Users Manual

FCC ID: ZZH-WF500D

Users Manual

Download: PDF
FCCID_3846958

INSTALLATION INSTRUCTIONS WF500D  INSTALLATION  MULTIGANG INSTALLATION Wireless Home Automation This WF500D dimmer switch may be used in new installations or replace an existing When installing more than one control in the same wall box, it may be necessary wall switch. to remove the side tabs before installing (see below). Using pliers, bend each tab WIFI Control Device back and forth until they break off. Repeat for each tab to be removed. Removal Dimmer Switch of tabs WILL REDUCE MAXIMUM LOAD CAPACITY. Typical Dimmer Wiring Schematic: Black Red 120 VAC Green 60 Hz Light White  SPECIFICATIONS Voltage...............................................................................................120VAC, 60Hz Incandescent.....................................................................................................600W Wiring Diagram: Tabs Removed for Mulitgang installation CFL/LED/Electronic self-ballasted.............................................................2A (150W) Operating Temperature.........................................................32°F~104°F(0°C~40°C) LED/CFL Derating Chart Wire Strip Length..................................................................................16mm(5/8 in.) Red Load Capacity when Tabs are removed from: Supply Connection...............................................................................14 AWG wires Load (to light fixture) 0 Sides 1 Side 2 Sides Dimmable LED/CFL 150W 150W 150W Screw Torque.................................................................................................20 lbf-in Green Protocol...........................................................................................IEEE 802.11b/g/n Ground Wireless Type................................................................................................ 2.4GHz When using the Dimmer to control LED/CFL lights in conjunction with another Dimmer White Black  FEATURES Hot (from breaker) to control Incandescent /Halogen lights follow this Derating Chart for Maximum Neutral Capacitiy on EACH device. Perfect Replacement for regular wall ON/OFF & Dim switch, 120VAC Manual and Remote ON/OFF& Dim control of any permanently installed incandescent, Then the Maximum COMBINED Wattaged for the If the combined Incandescent/Halogen bulbs on EACH attached dimmer: dimmable LED and CFL lamp fixture Wattage of ALL If NO Tabs are If 1 side of Tabs If 2 sides of Tabs Preset light level option allows the dimmer will turn on to the light level that it was 1. WARNING : To avoid fire, shock, or death. High Voltage - Turn off power at circuit LED/CFL bulbs removed then are removed then are removed then adjusted to the previous time when the light was on on 1 dimmer is: Max Wattage is: Max Wattage is: Max Wattage is: breaker or fuse and test that power is off before wiring. 0W 600W 500W 400W Air-Gap Switch feature meets UL requirement and disconnect power from load 2. CAUTION : To Reduce The Risk of Overheating and Possible Damage to Other 1-25W 500W 400W 300W locally. Equipment, Do Not Install to Control a Receptacle, a Motor-Operated Appliance 26-50W 400W 300W 200W or a Fluorescent Lighting Fixture or a Transformer Supplied Appliance.  DESCRIPTION 51-75W 300W 200W 100W 3. Remove wall plate and existing switch mounting screws. 76-100W 200W 100W 50W The WF500D Dimmer Switch is a perfect wireless manual and remote on/off/ dim 4. Carefully remove the existing switch from the switch box. 101-125W 100W 50W 0W bright control replacement of regular on/off and dimmer switch, controlling incandescent, 126-150W 0W 0W 0W 5. Disconnect the wiring from the existing switch. dimmable LED and CFL. Sliding Air-Gap switch to a totally disconnect power while 6. Connect the dimmer switch as shown in the wiring diagram: Black lead to hot replacing light bulbs and preventing from leakage current from the fixture(s). The If you are using ONLY LED/CFL bulbs on ALL Dimmers, DO NOT USE this Derating wire, white lead to neutral wire, red lead to load wire, green lead to ground wire. LED dimming performance may vary based upon dimmer type, model, manufacturer, Chart. Follow the LED/ CFL Derating Chart. 7. Check connections to be sure they are tight and no bare conductors are exposed. circuit wiring and circuit loading. No specific recommendation on product selection and there are no warranties of performance or compatibility implied. 8. Insert the WF500D dimmer switch into the standard outlet box carefully.  OPERATIONS 9. Make sure the WF500D dimmer switch to the box using the supplied screws. 10. Attach the wall plate. WARNINGS AND CAUTIONS 11. Restore power at the circuit breaker and test the system. Be sure to read the instruction carefully before installation, and the manufacturer Air Gap Switch Dimmer Switch Paddle will not be responsible for any product damage that does not follow the instruction During normal operation, there is a small amount of power passing through the 1. Wet hands are strictly prohibited. switch to the load even when the dimmer switch is turned off. The WF500D has an LED indicator Air Gap Switch 2. Must work strictly according to the rated load. air gap switch on the lower right side to completely disconnect power to the load. Slide the air gap switch to left to disconnect the power while replacing light bulbs 3. Do not continue to work after self-disassembly of any nature and damage of and slide it to right for normal operation. The air gap switch must be all the way in external forces. for the dimmer to function and control the lighting. -01- -02- -03-

INSTALLATION INSTRUCTIONS Manual Control d. Click the bottom button e. Enter your Wifi password f. Finished 3. When the device fail to add in the App, please try to enter the AP mode. The WF500D dimmer switch allows the user to: Before enter the AP mode please press the top or bottom button 5 times Turn ON/OFF and control the brightness level of the connected lighting. continuously, then press and hold at the sixth for 5 seconds then release, 1. To turn the connected lighting ON: Tap the top of the dimmer switch paddle. the LED indicator in green and slowly blinks. The LED indicator will be turned on in blue. 2. To turn the connected lighting OFF: Tap the bottom of the dimmer switch paddle again. The LED indicator will be turned off. 3. To brighten the connected lighting: Press and hold the top of the dimmer switch paddle, release when desired level is achieved. 4. To dim the connected lighting: Press and hold the bottom of the dimmer switch paddle, release when desired level is achieved. 4. When the device is added successfully, this WIFI Dimmer can be turned ON/OFF Please note: pressing and holding the dimmer switch paddle until the light intensity and dimmed. is at the minimum setting does not turn the power OFF, you must still tap (short press) the bottom of the dimmer switch paddle to turn the power OFF. Restoring Factory Defaults Tuya Smart App Control When power on the device and confirm that indicator light if rapidly blinks, if not please press the top or bottom button 5 times continuously, then press and hold 1. Download Tuya Smart app from the App Store or Google Play. at the sixth time then release, the LED indicator in green and flashes quickly. Please Note: When power is reconnected after the interruption, the LED indicator in green will flash quickly which means that the Dimmer is searching for WIFI. It will stop flashing and turn off when WIFI is connected successfully for 5 seconds. when the LED indicator in solid green that means your network anomaly, pls check the network. 2. Connect mobile device to your 2.4GHz WIFI network. Please note this  LED INDICATION Smart Dimmer Switch can only be connected to 2.4GHz network. Quick Blinking Green: Connecting to the network. Slow Blinking Green: AP mode. Please Note: Green bright after 2 seconds off: Connected to the network. 1. During the process of adding device, you must select the correct name of WIFI Soild Green: Network abnormaly . router and fill in the correct WIFI password, otherwise the device will not be able Solid Blue: The WIFI Dimmer is switched on. 3. Launch Tuya and follow the in-app instructions to connect the to add successfully. Off: The WIFI Dimmer is switched off. Smart Dimmer Switch to your network. 2. Now, this WIFI Dimmer is paired with one phone device. If you want to control  FCC COMPLIANCE the WIFI Dimmer by different phones, click the "profile" then chose the This device complies with Part 15 of the FCC Rules. Operation is subject to the a. Login the Tuya b. Click the button “+” c. Select the "Wall switch" " Device Sharing". following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.  WARRANTY INFORMATION Our company warranties its products to be free of defects in materials and workman -ship for a period of two (2) years. There are no obligations or liabilities on the part of our company for consequential damages arising out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation or reinstallation. Apr, 2018 20180426-00089 -04- -05- -06-

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna.


Document Created: 2018-05-10 15:58:43
Document Modified: 2018-05-10 15:58:43
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC