14_KB3 TestRpt JBP

FCC ID: ZRQKB3

Test Report

Download: PDF
FCCID_3987438

Page 1 of 23 FCC Test Report Report No.: AGC00803180702FE01 APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Penclic mini keyboard KB3 BRAND NAME : Penclic MODEL NAME : KB3 CLIENT : Penclic AB DATE OF ISSUE : Jul. 25, 2018 STANDARD(S) : FCC Part 15 Subpart B REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

Report No.: AGC00803180702FE01 Page 2 of 23 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 25, 2018 Valid Initial release

Report No.: AGC00803180702FE01 Page 3 of 23 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY ...................................................................................... 4 2. SYSTEM DESCRIPTION ...................................................................................................... 5 3. MEASUREMENT UNCERTAINTY........................................................................................ 5 4. SUMMARY OF TEST RESULTS .......................................................................................... 5 5. PRODUCT INFORMATION .................................................................................................. 6 6. SUPPORT EQUIPMENT....................................................................................................... 6 7. TEST FACILITY .................................................................................................................... 7 8. TEST EQUIPMENT LIST ...................................................................................................... 7 9. FCCLINE CONDUCTED EMISSION TEST .......................................................................... 8 9.1. LIMITS OF LINE CONDUCTED EMISSION TEST ....................................................... 8 9.2. BLOCK DIAGRAM OF TEST SETUP ........................................................................... 8 9.3. PROCEDURE OF LINE CONDUCTED EMISSION TEST ............................................ 9 9.4. TEST RESULT OF LINE CONDUCTED EMISSION TEST ......................................... 10 10. FCC RADIATED EMISSION TEST ................................................................................... 12 10.1. LIMITS OF RADIATED EMISSION TEST ................................................................. 12 10.2. BLOCK DIAGRAM OF TEST SETUP ....................................................................... 13 10.3. PROCEDURE OF RADIATED EMISSION TEST ...................................................... 14 10.4. TEST RESULT OF RADIATED EMISSION TEST ..................................................... 15 APPENDIX A: PHOTOGRAPHS OF TEST SETUP ............................................................... 17 APPENDIX B: PHOTOGRAPHS OF EUT .............................................................................. 18

® * * A\G § 43— }a; *fi ;I)]l] Report No.: AGC00803180702F E01 Attestation of Global Compliance Page 4 of 23 1. VERIFICATION OF CONFORMITY Applicant Penclic AB Address Vendev. 90, Danderyd, 182 32, Sweden Manufacturer Shenzhen Hangshi Technology Co., Ltd hadress Hangshi Technology Park, Democracy West Industry Area, Shajing Town, Bao‘an District, Shenzhen, China. Product Designation Penclic mini keyboard KB3 Brand Name Penclic Test Model KB3 Date of test Jul. 23, 2018 to Jul. 24, 2018 Deviation None Condition of Test Sample |Normal Report Template AGCRT—US—IT/AC The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. For compliance with the requirements set forth in the FCC Rules and Regulations Part 15, the measurement procedure according to ANSI ©C63.4:2014. This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment are within the compliance requirements. The test results of this report relate only to the tested sample identified in this report. Tested By Soder vht Jonhen Wang(Wang Yonghuan) Jul. 24, 2018 Reviewed By oi e Cool Cheng(Cheng Mengguo) Jul. 25, 2018 Approved By Forrest Lei(Lei Yonggang) Jul. 25, 2018 Authorized Officer The results ’m,6tison| o thisfea es report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A (§€ this docu/t& it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed t;!?ttp://www.agc-«drS t.com. o Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00803180702FE01 Page 5 of 23 2. SYSTEM DESCRIPTION EUT set up procedure: 1. Connect the EUT with PC. 2. Make sure the EUT c operates normally during the test. Test Mode TEST MODE DESCRIPTION NO. TEST MODE DESCRIPTION WORST 1 Data transmission V Note: V means EMI worst mode. 3. MEASUREMENT UNCERTAINTY The uncertainty is calculated using the methods suggested in the “Guide to the Expression of Uncertainty in Measurement” (GUM) published by ISO. - Uncertainty of Conducted Emission, Uc = ±3.2 dB - Uncertainty of Radiated Emission, Uc = ±3.2 dB 4. SUMMARY OF TEST RESULTS FCC Rules Description Of Test Result §15.107 Conduction Emission Compliant §15.109 Radiated Emission Compliant

Report No.: AGC00803180702FE01 Page 6 of 23 5. PRODUCT INFORMATION Housing Type Plastic and Metal Voltage DC 3.7V by battery I/O Port Information ( Applicable Not Applicable) I/O Port of EUT I/O Port Type Q’TY Cable Tested with USB Port 1 0 1 6. SUPPORT EQUIPMENT Device Type Manufacturer Model Name Serial No. Power Cable PC APPLE A1534 N/A 0 PC APPLE A1465 N/A 0 PC Adapter APPLE E132068 N/A 2m unshielded USB Cable N/A N/A N/A 1m unshielded Note: All the above equipment/cables were placed in worse case positions to maximize emission signals during emission test.

Report No.: AGC00803180702FE01 Page 7 of 23 7. TEST FACILITY Test Site Attestation of Global Compliance (Shenzhen) Co., Ltd 1-2F., Bldg.2, No.1-4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Location 1 Bao’an District, Shenzhen, Guangdong, P.R.China B112-B113, Bldg.12, Baoan Bldg Materials Center, No.1 of Xixiang Inner Ring Location 2 Road, Baoan District, Shenzhen 518012 Note: The test item conducted emission was tested in the laboratory of the location 1, the others were tested in the laboratory of the location 2. 8. TEST EQUIPMENT LIST TEST EQUIPMENT OF CONDUCTED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due Test Receiver ROHDE&SCHWARZ ESCI 100694 July 2, 2018 July 1, 2019 LISN R&S ESH3-Z5 838979/009 Mar.01 2018 Feb. 28, 2019 TEST EQUIPMENT OF RADIATED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESCI 10096 Jun.20, 2018 Jun.19, 2019 EXA Signal Analyzer Aglient N9010A MY53470504 Dec.08, 2017 Dec.07, 2018 ANTENNA SCHWARZBECK VULB9168 D69250 Sep.28, 2017 Sep.27, 2018 HORN ANTENNA EM EM-AH-10180 N/A Mar.01, 2018 Feb.28, 2019

Report No.: AGC00803180702FE01 Page 8 of 23 9. FCCLINE CONDUCTED EMISSION TEST 9.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz-500kHz 66-56 56-46 500kHz-5MHz 56 46 5MHz-30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50MHz. 9.2. BLOCK DIAGRAM OF TEST SETUP

Report No.: AGC00803180702FE01 Page 9 of 23 9.3. PROCEDURE OF LINE CONDUCTED EMISSION TEST (1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. (2) Support equipment, if needed, was placed as per ANSI C63.4. (3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. (4) The EUT received charging voltage by PC which receive AC120V/60Hz power from a LISN. (5) The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. (6) Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. (7) During the above scans, the emissions were maximized by cable manipulation. (8) A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. (9) Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. The test data of the worst case condition (mode 1) was reported on the Summary Data page.

Report No.: AGC00803180702FE01 Page 10 of 23 9.4. TEST RESULT OF LINE CONDUCTED EMISSION TEST LINE CONDUCTED EMISSION TEST-L

Report No.: AGC00803180702FE01 Page 11 of 23 LINE CONDUCTED EMISSION TEST-N RESULT: PASS

Report No.: AGC00803180702FE01 Page 12 of 23 10. FCC RADIATED EMISSION TEST 10.1. LIMITS OF RADIATED EMISSION TEST Frequency Distance Maximum Field Strength Limit (MHz) (m) (dBuV/m/ Q.P.) 30~88 3 40.0 88~216 3 43.5 216~960 3 46.0 960~1000 3 54.0 Above 1000 3 Other:74.0 dB(μV)/m (Peak) 54.0 dB(μV)/m (Average) Note: The lower limit shall apply at the transition frequency. 10.1.1 The following table is the setting of spectrum analyzer and receiver: Spectrum Parameter Setting Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP 1GHz~13GHz Start ~Stop Frequency RBW 1MHz/ VBW 3MHz for Peak, RBW 1MHz/ VBW 10Hz for Average Receiver Parameter Setting Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP

® * * A\G § 43— % *fi ;IJI’IJ Report No.: AGC00803180702F E01 Attestation of Global Compliance Page 13 of 23 10.2. BLOCK DIAGRAM OF TEST SETUP RADIATED EMISSION TEST SETUP 30MHz—1000MHz RX Antenna Ant. feed point [_~ z Spectrum Analyzer j Receiver System Simulator P yz * RADIATED EMISSION TEST SETUP ABOVE 1000MHz e Spectrum Analyzer / Receiver System Simulator The results s‘ & virl fii@sfi‘ kreport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued b , this docf&o it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed t;fittp://www.agc-«drS t.com. o Attestatic m ® ) i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 B# Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

® * * A\G § 43— }a; *fi ;I)]l] Report No.: AGC00803180702F E01 Attestation of Global Compliance Page 14 of 23 10.3. PROCEDURE OF RADIATED EMISSION TEST 1. Configure the EUT according to ANSI C63.4. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on the top of a height—variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test—receiver system to Peak or CISPR quasi—peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum values. The results ,u' & virl fiifisfi" treport refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A (§€ this docufi it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-«& t.com. o Attestatic s i Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@age—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00803180702FE01 Page 15 of 23 10.4. TEST RESULT OF RADIATED EMISSION TEST Radiated Emission Test at 3m Distance-Horizontal

Report No.: AGC00803180702FE01 Page 16 of 23 Radiated Emission Test at 3m Distance-Vertical RESULT: PASS Note: Measurement = Reading + Factor, Over = Measurement – Limit. 1~13GHz at least have 20dB margin. No recording in the test report.

Report No.: AGC00803180702FE01 Page 17 of 23 APPENDIX A: PHOTOGRAPHS OF TEST SETUP FCC LINE CONDUCTED EMISSION TEST SETUP FCC RADIATED EMISSION TEST SETUP

Report No.: AGC00803180702FE01 Page 18 of 23 APPENDIX B: PHOTOGRAPHS OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT

Report No.: AGC00803180702FE01 Page 19 of 23 FRONT VIEW OF EUT BACK VIEW OF EUT

Report No.: AGC00803180702FE01 Page 20 of 23 LEFT VIEW OF EUT RIGHT VIEW OF EUT

Report No.: AGC00803180702FE01 Page 21 of 23 VIEW OF EUT (Port) OPEN VIEW OF EUT

Report No.: AGC00803180702FE01 Page 22 of 23 VIEW OF BATTERY INTERNAL VIEW OF EUT-1 Antenna

Report No.: AGC00803180702FE01 Page 23 of 23 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 ----END OF REPORT----


Document Created: 2018-08-31 17:43:55
Document Modified: 2018-08-31 17:43:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC