Test Report 1

FCC ID: ZNFX525WA

Test Report

Download: PDF

FCCID_4380566

Report No. HCT-EM-1906-FI002-R2

REVISION HISTORY

The revision history for this test report is shown in table.

Revision No. Date of Issue Description

0 June 27, 2019 Initial Release

1 July 09, 2019 Revised of typos

2 July 26, 2019 Revised Clause 1.6 Calibration of Measuring Instrument

The device bearing the trade name and model specified above, has been shown to comply with the applicable
technical standards as indicated in the measurement report and was tested in accordance with the measurement
procedures specified in ANSI C63.4-2014. (See Test Report if any modifications were made for compliance)
I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my
supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the
completeness of these measurements and vouch for the qualifications of all persons taking them.
HCT certifies that no party to application has been denial the FCC benefits pursuant to Section 5301 of the Anti-
Drug Abuse Act of 1988, 21 U.S.C 862

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 3 of 27

Report No. HCT-EM-1906-FI002-R2

CONTENTS

1. GENERAL INFORMATION 5
1.1 Description of EUT 5
1.2 Tested System Details 7
1.3 Cable Description 7
1.4 Noise Suppression Parts on Cable. (I/O Cable) 8
1.5 Test Facility 9
1.6 Calibration of Measuring Instrument 9
1.7 Measurement Uncertainty 9
2. DESCRIPTION OF TEST 10
2.1 Measurement of Conducted Emission 10
2.2 Measurement of Radiated Emission 11
2.3 Configuration of Tested System 12
3. PRELIMINARY TEST 13
3.1 Conducted Emission 13
3.2 Radiated Emission 13
4. CONDUCTED EMISSION AND RADIATED EMISSION TEST SUMMARY 14
4.1 Conducted Emission 14
4.2 Radiated Emission Below 1 GHz 21
4.3 Radiated Emission Above 1 GHz 23
5. CONCLUSION 26
6. APPENDIX A. TEST SETUP PHOTOGRAPHS 27

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 4 of 27

Report No. HCT-EM-1906-FI002-R2

1. GENERAL INFORMATION

1.1 Description of EUT

Its basic purpose is used for communications.

FCC ID ZNFX525WA

IC 2703C-X525WA

Model LM-X525WA

Series Model Name LMX525WA, X525WA, LM-X525PR, LMX525PR, X525PR

EUT Type Multi-band GSM/WCDMA/LTE Phone with BT, WLAN and NFC

824.20 MHz to 848.80 MHz (GSM 850)
1 850.20 MHz to 1 909.80 MHz (GSM 1 900)
1 852.4 MHz to 1 907.6 MHz (WCDMA B2)
1712.4 MHz to 1752.6 MHz (WCDMA B4)
826.40 MHz to 846.60 MHz (WCDMA B5)
1 850 MHz to 1 910 MHz (LTE B2)
1 710 MHz to 1 755 MHz (LTE B4)
824 MHz to 849 MHz (LTE B5)
2 496 MHz to 2570 MHz (LTE B7)
699 MHz to 716 MHz (LTE B12)

TX Frequency 777 MHz to 787 MHz (LTE B13)
704 MHz to 716 MHz (LTE B17)
1 710 MHz to 1 780 MHz (LTE B66)
2 402 MHz to 2 480 MHz (Bluetooth)
2 412 MHz to 2 462 MHz (WiFi 2.4 GHz)
2 412 MHz to 2 462 MHz ( WiFi 2.4 GHz)
5 180 MHz to 5 240 MHz (WiFi 5 GHz_UNII 1)
5 260 MHz to 5 320 MHz (WiFi 5 GHz_UNII 2A)
5 500 MHz to 5 720 MHz (WiFi 5 GHz_UNII 2C)
5 745 MHz to 5 825 MHz (WiFi 5 GHz_UNII 3)
13.56 MHz (NFC)

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 5 of 27

Report No. HCT-EM-1906-FI002-R2

869.20 MHz to 893.80 MHz (GSM 850)
1 930.20 MHz to 1 989.80 MHz (GSM 1 900)
1 932.4 MHz to 1 987.6 MHz (WCDMA B2)
2 112.4 MHz to 2 152.6 MHz (WCDMA B4)
871.40 MHz to 891.60 MHz (WCDMA B5)
1 930 MHz to 1 990 MHz (LTE B2)
2 110 MHz to 2 155 MHz (LTE B4)
869 MHz to 894 MHz (LTE B5)
2 516 MHz to 2690 MHz (LTE B7)
729 MHz to 746 MHz (LTE B12)

RX Frequency 746 MHz to 756 MHz (LTE B13)
734 MHz to 746 MHz (LTE B17)
2 110 MHz to 2 200 MHz (LTE B66)
2 402 MHz to 2 480 MHz (Bluetooth)
2 412 MHz to 2 462 MHz (WiFi 2.4 GHz)
2 412 MHz to 2 462 MHz ( WiFi 2.4 GHz)
5 180 MHz to 5 240 MHz (WiFi 5 GHz_UNII 1)
5 260 MHz to 5 320 MHz (WiFi 5 GHz_UNII 2A)
5 500 MHz to 5 720 MHz (WiFi 5 GHz_UNII 2C)
5 745 MHz to 5 825 MHz (WiFi 5 GHz_UNII 3)
13.56 MHz (NFC)

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 6 of 27

Report No. HCT-EM-1906-FI002-R2

1.3 Cable Description

Product Power Cord I/O Cable Length
Port
Name Shielded (Y/N) Shielded (Y/N) (m)

Micro USB Y Y (P,D) 1.0
EUT
Earphone N/A N (D) 1.2

RJ 45 N/A N (D) 1.6

Notebook PC Serial(Mouse) N/A Y (D) 1.8

DC IN N N/A (P) 1.8

Gateway DC IN N N/A (P) 1.8
NOTE. The marked “(D)” means the data cable and “(P)” means the power cable.

1.4 Noise Suppression Parts on Cable (I/O Cable)

Product Ferrite Bead Metal Hood
Port Location Location
Name (Y/N) (Y/N)

Micro USB N N/A Y Both End
EUT
Earphone N N/A Y EUT End

RJ 45 N N/A N N/A

Notebook PC Notebook PC
Serial(Mouse) N N/A Y
End

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 8 of 27

Report No. HCT-EM-1906-FI002-R2

1.5 Test Facility

Test site is located at 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, South Korea.
Those measurement facilities are constructed in conformance with the requirements of ANSI C63.4-2014.
The Normalized site attenuations (30 MHz to 1 GHz) and Site validation (1 GHz to 18 GHz) were performed in
accordance with the standard in ANSI C63.4-2014

Measurement Facilities Designation No.

Radiated Field strength measurement facility
3 m Semi Anechoic chamber

Radiated Field strength measurement facility
KR0032
10 m Semi Anechoic chamber #1

Radiated Field strength measurement facility
10 m Semi Anechoic chamber #2

1.6 Calibration of Measuring Instrument

The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in ac
cordance with the manufacturers recommendations for utilizing calibration equipment, which is traceable to
recognized national standards.Espectially, all antenna for measurement is calibrated in accordance with the
requirements of C63.5:2017

1.7 Measurement Uncertainty

The measurement uncertainties shown below were calculated in accordance with the requirements
of ANSI C63.4-2014. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95 %
level of confidence. The measurement data shown herein meets or exceeds the UCISPR measurement uncertainty
values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance.

Parameter Expanded Uncertainty

Conducted Emission (0.15 MHz to 30 MHz) 1.78 dB

Radiated Emissions (30 MHz to 1 GHz) 6.00 dB

Radiated Emissions (1 GHz to 18 GHz) 4.78 dB

Radiated Emissions (18 GHz to 40 GHz) 4.94 dB

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 9 of 27

Report No. HCT-EM-1906-FI002-R2

2. DESCRIPTION OF TEST

2.1 Measurement of Conducted Emission

The test procedure was in accordance with ANSI C63.4-2014, Clause 7.3

a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the
power mains through a line impedance stabilization network (LISN).
If the EUT is connected to the PC through USB, the AC power-line adapter of the PC is directly connected to a
line impedance stabilization network (LISN).
Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/
50uH of coupling impedance for the measuring instrument.
b. Both conducted lines are measured in Quasi-Peak and Average mode, including the worst-case data points for
each tested configuration.
c. The frequency range from 150 kHz to 30 MHz was searched.

Conducted Emission Limits

Resolution Class A Class B
Frequency
Bandwidth Quasi-Peak Average Quasi-Peak Average
(MHz)
(kHz) (dBμV) (dBμV) (dBμV) (dBμV)

0.15 to 0.5 9 79 66 66 to 56* 56 to 46*

0.5 to 5 9 73 60 56 46

5 to 30 9 73 60 60 50

NOTE. Decreases with the logarithm of the frequency.

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 10 of 27

Report No. HCT-EM-1906-FI002-R2

2.2 Measurement of Radiated Emission

The test procedure was in accordance with ANSI C63.4-2014, Clause 8.3

a. The EUT was placed on the top of a turn table 0.8 meters above the ground at a semi-anechoic chamber.
The table was rotated 360 degrees to determine the position of the highest radiation.
b. The EUT was set 3 m away from the interference-receiving antenna, which was mounted on the top of a
variable-height antenna tower.
c. The antenna height is varied from 1 m to 4 m above the ground to determine the maximum value of the field
strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights
from 1 m to 4 m and the turn table was turned from 0 degrees to 360 degrees to find the maximum reading.
e. The test-receiver system was set to Quasi-Peak detect function and specified bandwidth with maximum hold
mode when the test frequency is below 1 GHz.
f. The test-receiver system was set to Peak and Average detect function and specified bandwidth with maximum
hold mode when the test frequency is above 1 GHz.
g. Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the
specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at
each frequency of significant emissions, with polarization oriented for maximum response.
(1 GHz to 40 GHz)

Radiated Emission Limits

Class A Class B
Frequency Antenna Field Antenna Field
(MHz) Quasi-Peak Quasi-Peak
Distance Strength Distance Strength
(dBμV/m) (dBμV/m)
(m) (μV/m) (m) (μV/m)

30 to 88 10 90 39.0 3 100 40.0

88 to 216 10 150 43.5 3 150 43.5

216 to 960 10 210 46.4 3 200 46.0

Above 960 10 300 49.5 3 500 54.0

Class A Class B
Frequency Antenna Distance
(MHz) (m) Peak Average Peak Average
(dBμV/m) (dBμV/m) (dBμV/m) (dBμV/m)

Above 1 000 3 80 60 74 54

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 11 of 27

Report No. HCT-EM-1906-FI002-R2

2.2.1 Frequency Range of Radiated Measurements

An unintentional radiator, including a digital device, the spectrum shall be investigated from the lowest radio
frequency signal generated or used in the device, without going below the lowest frequency for which a Radiated
Emission limit is specified, up to the frequency shown in the following table

Highest frequency generated or used in the device
Upper frequency of measurement range
or on which the device operates
(MHz)
or tunes (MHz)

Below 1.705 30

1.705 to 108 1 000
108 to 500 2 000
500 to 1 000 5 000
5th harmonic of the highest frequency
Above 1 000
or 40 놄, whichever is lower
Below 1.705 30

2.3 Configuration of Tested System

Notebook Notebook PC
Gateway Adaptor EUT
PC adaptor

Non-Conductive Table Earphone Serial Mouse

Power Line: 120 VAC, 60 Hz

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 12 of 27

Report No. HCT-EM-1906-FI002-R2

3. PRELIMINARY TEST

3.1 Conducted Emission

It was tested the following operating mode, after connecting all peripheral devices.

Operating Modes: Data Communication mode

3.2 Radiated Emission

It was tested the following operating mode, after connecting all peripheral devices.

Operating Modes: Data Communication mode

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 13 of 27

Report No. HCT-EM-1906-FI002-R2

4. CONDUCTED EMISSION AND RADIATED EMISSION TEST SUMMARY

4.1 Conducted Emission

4.1.1 Measuring instruments

Serial Calibration Calibration
Type Manufacturer Model Name
Number Cycle Date

EMI Test Receiver Rohde & Schwarz ESCI 100584 1 year 06.18.2019

LISN Rohde & Schwarz ENV216 102245 1 year 12.12.2018

LISN Rohde & Schwarz ENV216 100073 1 year 04.30.2019

Software Rohde & Schwarz EMC32 VER8.54.0 - - -

4.1.2 Operating Condition

The test results of conducted emission at mains ports provide the following information:

FCC CFR 47 PART 15 Subpart B Class B
Test Standard Used ICES-003 Issue 6 Class B
ANSI C63.4-2014

Detector Quasi-Peak, CISPR-Average

Bandwidth 9 kHz (6 dB)

Operating Mode Data Communication mode

Worst Case of Data Cable KSD (EAD62377922)

Kind of Test Site Shielded Room

Temperature 23.7 °C

Relative Humidity 43.8 %

Test Date June 20, 2019

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 14 of 27

Report No. HCT-EM-1906-FI002-R2

4.1.3 Measuring Data

Figure 1: Conducted Emission, AC Main Port, Line (L1)

FCC CLASS B

90

80

70

60

50
Level in dBμ

40

30

20

10

0

-10
150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M

Frequency in Hz

FCC CLASS B_QP FCC CLASS B_ AV Preview Result 1-PK+
Preview Result 2-AVG Final Result 1-QPK Final Result 2-CAV

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 15 of 27

Report No. HCT-EM-1906-FI002-R2

QuasiPeak Final Result, Line (L1)

Frequency QuasiPeak Bandwidth Corr. Margin Limit
Line
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.150000 43.3 9.000 L1 9.6 22.7 66.0
0.154000 42.9 9.000 L1 9.6 22.9 65.8
0.162000 43.3 9.000 L1 9.6 22.1 65.4
0.168000 44.0 9.000 L1 9.6 21.1 65.1
0.174000 44.0 9.000 L1 9.6 20.7 64.8
0.188000 41.8 9.000 L1 9.7 22.4 64.1
3.120000 31.8 9.000 L1 9.8 24.2 56.0
3.186000 30.4 9.000 L1 9.8 25.6 56.0
3.222000 31.0 9.000 L1 9.8 25.0 56.0
3.430000 30.2 9.000 L1 9.8 25.8 56.0
3.634000 29.0 9.000 L1 9.8 27.0 56.0
3.638000 29.4 9.000 L1 9.8 26.6 56.0
9.062000 28.6 9.000 L1 9.9 31.4 60.0
9.260000 29.4 9.000 L1 10.0 30.6 60.0
9.320000 29.3 9.000 L1 10.0 30.7 60.0
9.344000 29.6 9.000 L1 10.0 30.4 60.0
9.370000 29.4 9.000 L1 10.0 30.6 60.0
9.468000 29.4 9.000 L1 10.0 30.6 60.0

Calculation Formula:
1. Conductor L1 = Hot, Conductor N = Neutral
2. Corr. = LISN Factor + Cable Loss
3. QuasiPeak or CAverage= Receiver Reading + Corr.
4. Margin = Limit – QuasiPeak or CAverage

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 16 of 27

Report No. HCT-EM-1906-FI002-R2

CAverage Final Result, Line (L1)

Frequency CAverage Bandwidth Corr. Margin Limit
Line
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.150000 28.0 9.000 L1 9.6 28.0 56.0
0.162000 27.9 9.000 L1 9.6 27.5 55.4
0.166000 32.5 9.000 L1 9.6 22.7 55.2
0.172000 31.8 9.000 L1 9.6 23.0 54.9
0.176000 32.0 9.000 L1 9.6 22.7 54.7
0.188000 30.4 9.000 L1 9.7 23.7 54.1
3.120000 22.9 9.000 L1 9.8 23.1 46.0
3.222000 22.7 9.000 L1 9.8 23.3 46.0
3.226000 22.7 9.000 L1 9.8 23.3 46.0
3.428000 21.7 9.000 L1 9.8 24.3 46.0
3.634000 20.2 9.000 L1 9.8 25.8 46.0
3.638000 19.9 9.000 L1 9.8 26.1 46.0
9.062000 20.9 9.000 L1 9.9 29.1 50.0
9.204000 21.6 9.000 L1 9.9 28.4 50.0
9.272000 21.5 9.000 L1 10.0 28.5 50.0
9.320000 22.0 9.000 L1 10.0 28.0 50.0
9.344000 21.8 9.000 L1 10.0 28.2 50.0
9.370000 22.3 9.000 L1 10.0 27.7 50.0

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 17 of 27

Report No. HCT-EM-1906-FI002-R2

Figure 2: Conducted Emission, AC Main Port, Line (N)

FCC CLASS B

90

80

70

60

50
Level in dBμ

40

30

20

10

0

-10
150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M
Frequency in Hz

FCC CLASS B_QP FCC CLASS B_ AV Preview Result 1-PK+
Preview Result 2-AVG Final Result 1-QPK Final Result 2-CAV

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 18 of 27

Report No. HCT-EM-1906-FI002-R2

QuasiPeak Final Result, Line (N)

Frequency QuasiPeak Bandwidth Corr. Margin Limit
Line
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.152000 42.9 9.000 N 9.6 22.9 65.9
0.156000 42.3 9.000 N 9.6 23.3 65.7
0.166000 42.6 9.000 N 9.6 22.5 65.2
0.174000 44.7 9.000 N 9.6 20.1 64.8
0.178000 44.2 9.000 N 9.6 20.3 64.6
0.186000 43.5 9.000 N 9.6 20.7 64.2
3.814000 28.4 9.000 N 9.8 27.6 56.0
3.916000 27.7 9.000 N 9.8 28.3 56.0
3.922000 28.6 9.000 N 9.8 27.4 56.0
4.020000 29.6 9.000 N 9.8 26.4 56.0
4.158000 30.6 9.000 N 9.8 25.4 56.0
4.636000 28.5 9.000 N 9.8 27.5 56.0
5.160000 23.9 9.000 N 9.8 36.1 60.0
5.258000 23.9 9.000 N 9.8 36.1 60.0
9.380000 28.7 9.000 N 9.9 31.3 60.0
9.554000 29.1 9.000 N 9.9 30.9 60.0
9.648000 29.4 9.000 N 9.9 30.6 60.0
9.970000 29.2 9.000 N 9.9 30.8 60.0

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 19 of 27

Report No. HCT-EM-1906-FI002-R2

CAverage Final Result, Line (N)

Frequency CAverage Bandwidth Corr. Margin Limit
Line
(MHz) (dBμV) (kHz) (dB) (dB) (dBμV)
0.150000 27.5 9.000 N 9.6 28.5 56.0
0.154000 27.3 9.000 N 9.6 28.5 55.8
0.164000 28.6 9.000 N 9.6 26.7 55.3
0.168000 30.6 9.000 N 9.6 24.5 55.1
0.176000 31.6 9.000 N 9.6 23.1 54.7
0.184000 31.5 9.000 N 9.6 22.8 54.3
3.712000 17.8 9.000 N 9.8 28.2 46.0
3.814000 18.6 9.000 N 9.8 27.4 46.0
3.916000 19.5 9.000 N 9.8 26.5 46.0
4.018000 20.6 9.000 N 9.8 25.4 46.0
4.224000 21.9 9.000 N 9.8 24.1 46.0
4.406000 21.7 9.000 N 9.8 24.3 46.0
5.160000 15.7 9.000 N 9.8 34.3 50.0
5.258000 13.9 9.000 N 9.8 36.1 50.0
5.564000 13.4 9.000 N 9.9 36.6 50.0
9.380000 20.7 9.000 N 9.9 29.3 50.0
9.648000 21.2 9.000 N 9.9 28.8 50.0
9.970000 21.1 9.000 N 9.9 28.9 50.0

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 20 of 27

Report No. HCT-EM-1906-FI002-R2

4.2 Radiated Emission Below 1 GHz

4.2.1 Measuring instruments

Serial Calibration Calibration
Type Manufacturer Model Name
Number Cycle Date

EMI test receiver Rohde & Schwarz ESU40 100524 1 year 05.17.2019

Trilog antenna Schwarzbeck VULB 9168 255 2 year 03.26.2019

Antenna master INNCO Systems MA4640-XP-ET - N/A -
Antenna master CO3000/870/
INNCO Systems CO 3000 N/A -
controller 35990515/L
Turn Table INNCO Systems 1060 - N/A -
CO2000/095/
Turn table controller INNCO Systems CO2000 N/A -
7590304/L
Software Rohde & Schwarz EMC32 VER8.40.0 - - -

4.2.2 Operating Condition

The test results of radiated emission provide the following information:

FCC CFR 47 PART 15 Subpart B Class B
Used Test Standard ICES-003 Issue 6 Class B
ANSI C63.4-2014

Detector Quasi-Peak

Bandwidth 120 kHz (6 dB)

Operating Mode Data Communication mode

Worst Case of Data Cable KSD (EAD62377922)

Kind of Test Site 3 m semi anechoic chamber

Temperature 22.5 / 23.8 °C

Relative Humidity 42.1 / 43.1 %

Test Date June 25 / June 26, 2019

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 21 of 27

Report No. HCT-EM-1906-FI002-R2

4.2.3 Measuring Data

Antenna
Frequency Quasi Peak POL. Azimuth Corr. Margin Limit
Height
(MHz) (dBμV/m) (H/V) (deg) (dB) (dB) (dBμV/m)
(cm)
30.104800 24.5 100.0 V 22.0 18.3 15.5 40.0
87.378400 25.8 307.7 H 293.0 14.7 14.2 40.0
111.478400 23.2 100.0 V 8.0 16.5 20.3 43.5
265.522400 32.3 125.0 H 154.0 19.3 13.7 46.0
600.044000 36.9 100.0 V 346.0 27.4 9.1 46.0
800.022400 40.0 274.8 H 73.0 30.4 6.0 46.0

- Calculation Formula:
1. POL. H = Horizontal, POL. V = Vertical
2. QuasiPeak = Reading (Receiver Reading) + Corr.
3. Corr. (Correction Factor) = Antenna Factor + Cable Loss
4. Margin = Limit - QuasiPeak

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 22 of 27

Report No. HCT-EM-1906-FI002-R2

4.3 Radiated Emission Above 1 GHz

4.3.1 Measuring instruments

Serial Calibration Calibration
Type Manufacturer Model Name
Number Cycle Date

EMI test receiver Rohde & Schwarz ESU40 100524 1 year 05.17.2019

Antenna master INNCO Systems MA4640-XP-ET - N/A -

Antenna master CO3000/870/
INNCO Systems CO3000 N/A -
controller 35990515/L

Turn table INNCO Systems 1060 - N/A -

CO2000/095/
Turn table controller INNCO Systems CO2000 N/A -
7590304/L

Low Noise amplifier TESTEK TK-PA18H 170034-L 1 year 03.04.2019

Horn antenna Schwarzbeck BBHA 9120D 01836 1 year 07.20.2018

Power Amplifier TK-PA1840H TESTEK 170030-L 1 year 12.17.2018

BBHA9170
Horn Antenna BBHA 9170 Schwarzbeck 2 year 12.05.2017
#786

Software Rohde & Schwarz EMC32 VER8.40.0 - - -

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 23 of 27

Report No. HCT-EM-1906-FI002-R2

4.3.2 Operating Condition

The test results of radiated emission provide the following information:

FCC CFR 47 PART 15 Subpart B Class B
Used Test Standard ICES-003 Issue 6 Class B
ANSI C63.4-2014

Peak mode: Peak (RBW: 1 MHz, VBW: 3 MHz)
Detector
CISPR-Average mode: Peak (RBW: 1 MHz, VBW: 10 Hz)

Highest Frequency 5 825 MHz

Tested Frequency Range 1 GHz to 30 GHz

Operation Mode Data Communication mode

Worst Case of Data Cable KSD (EAD62377922)

Kind of Test Site 3 m semi anechoic chamber

Temperature 22.5 °C

Relative Humidity 42.1 %

Test Date June 25, 2019

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 24 of 27

Report No. HCT-EM-1906-FI002-R2

4.3.3 Measuring Data

Antenna
Frequency Peak POL. Azimuth Corr. Margin Limit
Height
(MHz) (dBμV/m) (H/V) (deg) (dB) (dB) (dBμV/m)
(cm)
1400.135000 48.3 232.6 V 256.0 -26.0 25.7 74.0
2010.145000 49.2 112.4 V 53.0 -25.2 24.8 74.0
2661.960000 50.3 125.7 V 0.0 -22.6 23.7 74.0
2796.700000 46.2 100.0 V 4.0 -22.0 27.8 74.0
5993.715000 44.2 111.4 V 323.0 -14.7 29.8 74.0
14659.635000 49.3 100.0 H 28.0 0.9 24.7 74.0

Antenna
Frequency CAverage POL. Azimuth Corr. Margin Limit
Height
(MHz) (dBμV/m) (H/V) (deg) (dB) (dB) (dBμV/m)
(cm)
1400.135000 46.4 232.6 V 256.0 -26.0 7.6 54.0
2010.145000 24.9 112.4 V 53.0 -25.2 29.1 54.0
2661.960000 23.6 125.7 V 0.0 -22.6 30.4 54.0
2796.700000 22.1 100.0 V 4.0 -22.0 31.9 54.0
5993.715000 28.4 111.4 V 323.0 -14.7 25.6 54.0
14659.635000 36.1 100.0 H 28.0 0.9 17.9 54.0

- Calculation Formula:
1. POL. H = Horizontal, POL. V = Vertical
2. Peak or CAverage = Reading (Receiver Reading) + Corr.
3. Corr. (Correction Factor) = Antenna Factor+ Cable Loss –Amplifier Gain
4. Margin = Limit - Peak or CAverage

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 25 of 27

Report No. HCT-EM-1906-FI002-R2

5. CONCLUSION

The data collected shows that the EUT Type: Multi-band GSM/WCDMA/LTE Phone with BT, WLAN and NFC,
Model: LM-X525WA complies with §15.107 and §15.109 of the FCC rules and ICES-003 Issue 6 of the IC rules.

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 26 of 27

Report No. HCT-EM-1906-FI002-R2

6. APPENDIX A. TEST SETUP PHOTO

Please refer to Appendix. A and test setup photo file no. as follows;

File No. Date of Issue Description

HCT-EM-1906-FI002-P June 27, 2019 Initial Release

End of report

This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd.

F-TP22-03 (Rev. 01) Page 27 of 27

Document Created: 2019-07-26 16:36:04
Document Modified: 2019-07-26 16:36:04

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC