Part 90 Test Report

FCC ID: ZNFX410AS

Test Report

Download: PDF
FCCID_3857140

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctest.com MEASUREMENT REPORT FCC Part 90 Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 3/14 - 5/17/2018 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab. Columbia, MD, USA United States Test Report Serial No.: 1M1803140041-12-R1.ZNF FCC ID: ZNFX410AS APPLICANT: LG Electronics MobileComm U.S.A Application Type: Certification Model: LM-X410AS Additional Model(s): LMX410AS, X410AS, LM-X410ASR, LMX410ASR, X410ASR EUT Type: Portable Handset FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) FCC Rule Part: §2.1049, §90 ISED Specification: RSS-140 Issue 1 Test Procedure(s): ANSI C63.26-2015, ANSI/TIA-603-E-2016, KDB 971168 D01 v03r01 This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in §2.947. Test results reported herein relate only to the item(s) tested. This revised Test Report (S/N: 1M1803140041-12-R1.ZNF) supersedes and replaces the previously issued test reports (S/N: 1M1803140041-12.ZNF) on the same subject device for the same type of testing as indicated. Please discard or destroy the previously issued test report(s) and dispose of it accordingly. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

T A B L E O F C O N T E N T S 1.0 INTRODUCTION ........................................................................................................................................... 4 1.1 Scope ................................................................................................................................................................. 4 1.2 PCTEST Test Location....................................................................................................................................... 4 1.3 Test Facility / Accreditations ............................................................................................................................... 4 2.0 PRODUCT INFORMATION........................................................................................................................... 5 2.1 Equipment Description ....................................................................................................................................... 5 2.2 Device Capabilities ............................................................................................................................................. 5 2.3 Test Configuration .............................................................................................................................................. 5 2.4 EMI Suppression Device(s)/Modifications .......................................................................................................... 5 3.0 DESCRIPTION OF TESTS ........................................................................................................................... 6 3.1 Evaluation Procedure ......................................................................................................................................... 6 3.2 Radiated Power and Radiated Spurious Emissions ........................................................................................... 6 4.0 MEASUREMENT UNCERTAINTY ................................................................................................................ 7 5.0 TEST EQUIPMENT CALIBRATION DATA ................................................................................................... 8 6.0 SAMPLE CALCULATIONS ........................................................................................................................... 9 7.0 TEST RESULTS .......................................................................................................................................... 10 7.1 Summary .......................................................................................................................................................... 10 7.2 Occupied Bandwidth ........................................................................................................................................ 11 7.3 Spurious and Harmonic Emissions at Antenna Terminal ................................................................................. 14 7.4 Band Edge Emission at the Antenna Terminal ................................................................................................. 17 7.5 Conducted Power Output Data ........................................................................................................................ 22 7.6 Radiated Power (ERP) ..................................................................................................................................... 23 7.7 Radiated Spurious Emissions Measurements .................................................................................................. 26 7.8 Frequency Stability / Temperature Variation .................................................................................................... 30 Frequency Stability / Temperature Variation ................................................................................................................ 31 8.0 CONCLUSION ............................................................................................................................................. 33 MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

MEASUREMENT REPORT FCC Part 90 Max. Max. Tx Frequency Emission Mode Measurement Power Power Modulation (MHz) Designator (W) (dBm) LTE Band 14 790.5 - 795.5 ERP 0.093 19.68 4M54G7D QPSK LTE Band 14 790.5 - 795.5 ERP 0.077 18.89 4M54W7D 16-QAM LTE Band 14 793 ERP 0.092 19.66 9M02G7D QPSK LTE Band 14 793 ERP 0.081 19.07 8M98W7D 16-QAM EUT Overview MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Innovation, Science and Economic Development Canada. 1.2 PCTEST Test Location These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The measurement facility is compliant with the test site requirements specified in ANSI C63.4-2014. 1.3 Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A. • PCTEST is an ISO 17025-2005 accredited test facility under the American Association for Laboratory Accreditation (A2LA) with Certificate number 2041.01 for Specific Absorption Rate (SAR), Hearing Aid Compatibility (HAC) testing, where applicable, and Electromagnetic Compatibility (EMC) testing for FCC and Innovation, Science, and Economic Development Canada rules. • PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC 17065-2012 by A2LA (Certificate number 2041.03) in all scopes of FCC Rules and ISED Standards (RSS). • PCTEST facility is a registered (2451B) test laboratory with the site description on file with ISED. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFX410AS. The test data contained in this report pertains to the emissions due to the EUT’s licensed transmitters that operate under the provisions of Part 90 and RSS-140. Test Device Serial No.: 1223, 1413, 1231 2.2 Device Capabilities This device contains the following capabilities: 850/1900 GSM/GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n WLAN, 802.11a/n/ac UNII, Bluetooth (1x, EDR, LE) 2.3 Test Configuration The EUT was tested per the guidance of ANSI/TIA-603-D-2010 and KDB 971168 D01 v03r01. See Section 7.0 of this test report for a description of the radiated and antenna port conducted emissions tests. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and no modifications were made during testing. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the document titled “Land Mobile FM or PM – Communications Equipment – Measurements and Performance Standards” (ANSI/TIA-603-D-2010) and “Procedures for Compliance Measurement of the Fundamental Emission Power of Licensed Wideband (> 1 MHz) Digital Transmission Systems” (KDB 971168 D01 v03r01) were used in the measurement of the EUT. 3.2 Radiated Power and Radiated Spurious Emissions §2.1053, §90.542, §90.543, RSS-140 The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x 5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections for measurements above 1GHz. For measurements below 1GHz, the absorbers are removed. A raised turntable is used for radiated measurement. The turn table is a continuously rotatable, remote-controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm tall test table made of Styrodur is placed on top of the turn table. A Styrodur pedestal is placed on top of the test table to bring the total table height to 1.5m. The equipment under test was transmitting while connected to its integral antenna and is placed on a wooden turntable 80cm above the ground plane and 3 meters from the receive antenna. The receive antenna height is adjusted between 1 and 4 meter height, the turntable is rotated through 360 degrees, and the EUT is manipulated through all orthogonal planes representative of its typical use to achieve the highest reading on the receive spectrum analyzer. Radiated power levels are also investigated with the receive antenna horizontally and vertically polarized. The maximized power level is recorded using the spectrum analyzer “Channel Power” function with the integration band set to the emissions’ occupied bandwidth, a RMS detector, RBW = 100kHz, VBW = 300kHz, and a 1 second sweep time over a minimum of 10 sweeps, per the guidelines of KDB 971168 D01 v03r01. Per the guidance of ANSI/TIA-603-D-2010, a half-wave dipole is then substituted in place of the EUT. For emissions above 1GHz, a horn antenna is substituted in place of the EUT. The substitute antenna is driven by a signal generator with the level of the signal generator being adjusted to obtain the same receive spectrum analyzer level previously recorded from the spurious emission from the EUT. The power of the emission is calculated using the following formula: Pd [dBm] = Pg [dBm] – cable loss [dB] + antenna gain [dBd/dBi] Where, Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). For fundamental radiated power measurements, the guidance of KDB 971168 D01 v03r01 is used to record the EUT power level that is subsequently matched via the aforementioned substitution method given in ANSI/TIA-603- D-2010. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

4.0 MEASUREMENT UNCERTAINTY The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.4-2014. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (±dB) Conducted Bench Top 1.13 Measurements Radiated Disturbance (<1GHz) 4.98 Radiated Disturbance (>1GHz) 5.07 Radiated Disturbance (>18GHz) 5.09 MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

5.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5- 2017. Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number - RE1 Radiated Emissions Cable Set (UHF/EHF) 6/21/2017 Annual 6/21/2018 RE1 - LTx3 LIcensed Transmitter Cable Set 8/10/2017 Annual 8/10/2018 LTx3 Agilent N9030A PXA Signal Analyzer (44GHz) 3/27/2017 Annual 3/27/2018 MY52350166 Com-Power AL-130 9kHz - 30MHz Loop Antenna 10/10/2017 Biennial 10/10/2019 121034 Com-Power PAM-103 Pre-Amplifier (1-1000MHz) 6/21/2017 Annual 6/21/2018 441128 Espec ESX-2CA Environmental Chamber 3/28/2018 Annual 3/28/2019 17620 ETS Lindgren 3117 1-18 GHz DRG Horn (Medium) 12/1/2016 Biennial 12/1/2018 125518 ETS Lindgren 3164-08 Quad Ridge Horn Antenna 3/28/2018 Biennial 3/28/2020 128337 Mini Circuits TVA-11-422 RF Power Amp N/A QA1317001 Mini Circuits PWR-SEN-4GHS USB Power Sensor 3/30/2018 Annual 3/30/2019 11401010036 Mini-Circuits SSG-4000HP Synthesized Signal Generator N/A 11403100002 Rohde & Schwarz CMW500 Radio Communication Tester N/A 100976 Rohde & Schwarz ESU40 EMI Test Receiver (40GHz) 7/31/2017 Annual 7/31/2018 100348 Rohde & Schwarz SFUNIT-Rx Shielded Filter Unit 7/3/2017 Annual 7/3/2018 102133 Table 5-1. Test Equipment Notes: 1. For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. 2. Equipment with a calibration date of “N/A” shown in this list was not used to make direct calibrated measurements. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

6.0 SAMPLE CALCULATIONS Emission Designator QPSK Modulation Emission Designator = 8M62G7D LTE BW = 8.62 MHz G = Phase Modulation 7 = Quantized/Digital Info D = Data transmission, telemetry, telecommand 16QAM Modulation Emission Designator = 8M45W7D LTE BW = 8.45 MHz W = Amplitude/Angle Modulated 7 = Quantized/Digital Info D = Data transmission, telemetry, telecommand Spurious Radiated Emission – LTE Band Example: Middle Channel LTE Mode 2nd Harmonic (1564 MHz) The average spectrum analyzer reading at 3 meters with the EUT on the turntable was –81.0 dBm. The gain of the substituted antenna is 8.1 dBi. The signal generator connected to the substituted antenna terminals is adjusted to produce a reading of –81.0 dBm on the spectrum analzyer. The loss of the cable between the signal generator and the terminals of the substituted antenna is 2.0 dB at 1564 MHz. So 6.1 dB is added to the signal generator reading of –30.9 dBm yielding –24.80 dBm. The fundamental EIRP was 25.501 dBm so this harmonic was 25.501 dBm – (-24.80). MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.0 TEST RESULTS 7.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFX410AS FCC Classification: PCS Licensed Transmitter Held to Ear (PCE) Mode(s): LTE Band: B14 FCC Part Test Test Test Description Test Limit Reference Section(s) Condition Result 2.1049 Occupied Bandwidth N/A PASS Section 7.2 On all frequencies between 769- 775 MHz and 799-805 MHz, attenuation by a factor not less than 65 + 10 log (P) dB in a 6.25 kHz band segment, for mobile 2.1051 Conducted Band Edge / Sections and portable stations. PASS 90.543 Spurious Emissions 7.3, 7.4 CONDUCTED On any frequency between 775- 788 MHz, above 805 MHz, and below 758 MHz, attenuation by at least 43 + 10 log (P) dB. 2.1055 Frequency Stability < 2.5 ppm PASS Section 7.8 90.213 2.1046 Conducted Power N/A PASS Section 7.5 Effective Radiated Power 90.542 3 Watts PASS Section 7.7 (ERP) > 43 + log10 (P[Watts]) for all out- of-band emissions all emissions including RADIATED 2.1053 Radiated Spurious harmonics in the band 1559- PASS Section 7.7 90.543 Emissions 1610 MHz shall be limited to −70 dBW/MHz equivalent isotropically radiated power (EIRP) for wideband signals, and −80 dBW EIRP Table 7-1. Summary of Test Results Notes: 1) All modes of operation and data rates were investigated. The test results shown in the following sections represent the worst case emissions. 2) The analyzer plots shown in Section 7.0 were taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables, directional couplers, and attenuators used as part of the system to maintain a link between the call box and the EUT at all frequencies of interest. 3) All antenna port conducted emissions testing was performed on a test bench with the antenna port of the EUT connected to the spectrum analyzer through calibrated cables, attenuators, and couplers. 4) For conducted spurious emissions, automated test software was used to measure emissions and capture the corresponding plots necessary to show compliance. The measurement software utilized is PCTEST “2G/3G Automation,” Version 3.9. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.2 Occupied Bandwidth §2.1049, RSS-140 Test Overview The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. All modes of operation were investigated and the worst case configuration results are reported in this section. Test Procedure Used KDB 971168 D01 v03r01 – Section 4.2 Test Settings 1. The signal analyzer’s automatic bandwidth measurement capability was used to perform the 99% occupied bandwidth and the 26dB bandwidth. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. 2. RBW = 1 – 5% of the expected OBW 3. VBW ≥ 3 x RBW 4. Detector = Peak 5. Trace mode = max hold 6. Sweep = auto couple 7. The trace was allowed to stabilize 8. If necessary, steps 2 – 7 were repeated after changing the RBW such that it would be within 1 – 5% of the 99% occupied bandwidth observed in Step 7 Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-1. Test Instrument & Measurement Setup Test Notes None. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-1. Occupied Bandwidth Plot (LTE B14 - 5.0MHz QPSK – RB Size 25) Plot 7-2 Occupied Bandwidth Plot (LTE B14 - 5.0MHz 16-QAM – RB Size 25) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-3 Occupied Bandwidth Plot (LTE B14 - 10.0MHz QPSK – RB Size 50) Plot 7-4 Occupied Bandwidth Plot (LTE B14 - 10.0MHz 16-QAM – RB Size 50) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.3 Spurious and Harmonic Emissions at Antenna Terminal §2.1051 §90.543, RSS-140 Test Overview The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible attenuation level of any spurious emission is 43 + log10(P[Watts]), where P is the transmitter power in Watts. Test Procedure Used KDB 971168 D01 v03r01– Section 6.0 Test Settings 1. Start frequency was set to 30MHz and stop frequency was set to 10GHz (separated into at least two plots per channel) 2. RBW ≥ 1MHz 3. VBW ≥ 3 x RBW 4. Detector = RMS 5. Trace mode = max hold 6. Sweep time = auto couple 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-2. Test Instrument & Measurement Setup Test Notes Compliance with the applicable limits is based on the use of measurement instrumentation employing a resolution bandwidth of 100 kHz or greater for Part 22. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-5. Conducted Spurious Plot (LTE B14 – 10.0MHz QPSK – RB Size 1, RB Offset 0) Plot 7-6. Conducted Spurious Plot (LTE B14 – 10.0MHz QPSK – RB Size 1, RB Offset 0) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-7. Conducted Spurious Plot (LTE B14 – 10.0MHz QPSK – RB Size 1, RB Offset 0) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.4 Band Edge Emission at the Antenna Terminal §2.1051 §90.543, RSS-140 Test Overview All out of band emissions are measured with a spectrum analyzer connected to the antenna terminal of the EUT while the EUT is operating at maximum power, and at the appropriate frequencies. All data rates were investigated to determine the worst case configuration. All modes of operation were investigated and the worst case configuration results are reported in this section. The minimum permissible attenuation level of any spurious emission removed from the EA licensee’s frequency block is 43 + log10(P[Watts]), where P is the transmitter power in Watts. On all frequencies between 769-775 MHz and 799-805 MHz, by a factor not less than 65 + 10 log (P) dB in a 6.25 kHz band segment, for mobile and portable stations. Test Procedure Used KDB 971168 D01 v03r01– Section 6.0 Test Settings 1. Span was set large enough so as to capture all out of band emissions near the band edge 2. RBW = 100 kHz 3. VBW = 300 kHz 4. Detector = RMS 5. Trace mode = trace average 6. Sweep time = auto couple 7. The trace was allowed to stabilize Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-3. Test Instrument & Measurement Setup Test Notes None. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-8. Lower Band Edge Plot (LTE B14 5MHz QPSK – RB Size 25) Plot 7-9. Lower Emission Mask Plot (LTE B14 5MHz QPSK – RB Size 25) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-10. Upper Band Edge Plot (LTE B14 5MHz QPSK – RB Size 25) Plot 7-11. Upper Emission Mask Plot (LTE B14 5MHz QPSK – RB Size 25) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 19 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-12. Lower Band Edge Plot (LTE B14 10MHz QPSK – RB Size 50) Plot 7-13. Lower Emission Mask Plot (LTE B14 10MHz QPSK – RB Size 50) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 20 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Plot 7-14. Upper Band Edge Plot (LTE B14 10MHz QPSK – RB Size 50) Plot 7-15. Upper Emission Mask Plot (LTE B14 10MHz QPSK – RB Size 50) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 21 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.5 Conducted Power Output Data Channel Frequency Cond. PWR Cond. PWR Bandwidth Mod. [MHz] [dBm] [Watts] [MHz] 793.00 5 QPSK 25.15 0.327 793.00 5 16-QAM 23.90 0.245 793.00 10 QPSK 25.17 0.329 793.00 10 16-QAM 24.19 0.262 Table 7-2. LTE Band 14 Conducted Power Output Data NOTES: 1. For LTE mode, the device was tested under all modulations, RB sizes and offsets, and channel bandwidth configurations and the worst case emissions are reported with 1 RB. 2. This unit was tested with its standard battery. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 22 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.6 Radiated Power (ERP) §90.542 Test Overview Effective Radiated Power (ERP) measurements are performed using the substitution method described in ANSI/TIA-603-D-2010 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using vertically and horizontally polarized tuned dipole antennas. All measurements are performed as RMS average measurements while the EUT is operating at its maximum duty cycle, at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 D01 v03r01 – Section 5.2.1 ANSI/TIA-603-D-2010 – Section 2.2.17 Test Settings 1. Radiated power measurements are performed using the signal analyzer’s “channel power” measurement capability for signals with continuous operation. 2. RBW = 1 – 5% of the expected OBW, not to exceed 1MHz 3. VBW ≥ 3 x RBW 4. Span = 1.5 times the OBW 5. No. of sweep points > 2 x span / RBW 6. Detector = RMS 7. Trigger is set to “free run” for signals with continuous operation with the sweep times set to “auto”. 8. The integration bandwidth was roughly set equal to the measured OBW of the signal for signals with continuous operation. 9. Trace mode = trace averaging (RMS) over 100 sweeps 10. The trace was allowed to stabilize MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 23 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-4. Radiated Test Setup <1GHz Test Notes 1) The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case emissions are reported with the EUT positioning, modulations, RB sizes and offsets, and channel bandwidth configurations shown in the tables below. 2) This unit was tested with its standard battery. 3) For LTE mode, the device was tested under all modulations, RB sizes and offsets, and channel bandwidth configurations and the worst case emissions are reported with 1 RB. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 24 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Channel Ant. Antenna Turntable Substitute Ant. ERP Frequency RB ERP ERP Margin Bandwidth Mod. Pol. Height Azimuth Level Gain Limit [MHz] Size/Offset [dBm] [Watts] [dB] [MHz] [H/V] [cm] [degree] [dBm] [dBi] [dBm] 790.50 5 QPSK H 150 29 1/0 19.58 2.12 19.55 0.090 34.77 -15.22 793.00 5 QPSK H 150 9 1/0 19.70 2.13 19.68 0.093 34.77 -15.09 795.50 5 QPSK H 150 14 1/0 19.46 2.14 19.45 0.088 34.77 -15.32 790.50 5 16-QAM H 150 29 1/0 18.92 2.12 18.89 0.078 34.77 -15.88 793.00 5 16-QAM H 150 9 1/0 18.24 2.13 18.22 0.066 34.77 -16.55 795.50 5 16-QAM H 150 14 1/0 18.73 2.14 18.72 0.075 34.77 -16.05 793.00 10 QPSK H 150 9 1 / 25 19.68 2.13 19.66 0.093 34.77 -15.11 793.00 10 16-QAM H 150 9 1 / 25 19.09 2.13 19.07 0.081 34.77 -15.70 793.00 5 QPSK V 150 85 1/0 19.32 2.13 19.30 0.085 34.77 -15.47 Table 7-3. Summary of Test Results MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 25 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.7 Radiated Spurious Emissions Measurements §2.1053 §90.543, RSS-140 Test Overview Radiated spurious emissions measurements are performed using the substitution method described in ANSI/TIA- 603-D-2010 with the EUT transmitting into an integral antenna. Measurements on signals operating below 1GHz are performed using horizontally and vertically polarized tuned dipole antennas. Measurements on signals operating above 1GHz are performed using vertically and horizontally polarized broadband horn antennas. All measurements are performed as peak measurements while the EUT is operating at maximum power, and at the appropriate frequencies. Test Procedures Used KDB 971168 D01 v03r01– Section 5.8 ANSI/TIA-603-D-2010 – Section 2.2.12 Test Settings 1. RBW = 100kHz for emissions below 1GHz and 1MHz for emissions above 1GHz 2. VBW ≥ 3 x RBW 3. Span = 1.5 times the OBW 4. No. of sweep points > 2 x span / RBW 5. Detector = RMS 6. Trace mode = Average (Max Hold for pulsed emissions) 7. The trace was allowed to stabilize MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 26 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-5. Test Instrument & Measurement Setup Test Notes 1. This unit was tested with its standard battery. 2. The EUT was tested in three orthogonal planes and in all possible test configurations and positioning. The worst case setup is reported in the tables below. 3. The "-" shown in the following RSE tables are used to denote a noise floor measurement. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 27 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

OPERATING FREQUENCY: 790.50 MHz MODULATION SIGNAL: QPSK BANDWIDTH: 5.0 MHz DISTANCE: 3 meters LIMIT: -13 dBm Ant. Antenna Turntable Level at Substitute Spurious Frequency Margin Pol. Height Azimuth Antenna Antenna Gain Emission Level [MHz] [dB] [H/V] [cm] [degree] Terminals [dBm] [dBi] [dBm] 2371.50 H 150 350 -57.92 5.72 -52.20 -39.2 3162.00 H - - -64.05 6.67 -57.38 -44.4 Table 7-4. Radiated Spurious Data (LTE Band 14 – Low Channel) OPERATING FREQUENCY: 793.00 MHz MODULATION SIGNAL: QPSK BANDWIDTH: 5.0 MHz DISTANCE: 3 meters LIMIT: -13 dBm Ant. Antenna Turntable Level at Substitute Spurious Frequency Margin Pol. Height Azimuth Antenna Antenna Gain Emission Level [MHz] [dB] [H/V] [cm] [degree] Terminals [dBm] [dBi] [dBm] 2379.00 H 150 356 -57.01 5.71 -51.29 -38.3 3172.00 H - - -63.23 6.59 -56.63 -43.6 Table 7-5. Radiated Spurious Data (LTE Band 14 – Mid Channel) OPERATING FREQUENCY: 795.50 MHz MODULATION SIGNAL: QPSK BANDWIDTH: 5.0 MHz DISTANCE: 3 meters LIMIT: -13 dBm Ant. Antenna Turntable Level at Substitute Spurious Frequency Margin Pol. Height Azimuth Antenna Antenna Gain Emission Level [MHz] [dB] [H/V] [cm] [degree] Terminals [dBm] [dBi] [dBm] 2386.50 H 150 352 -59.42 5.71 -53.71 -40.7 3182.00 H - - -62.50 6.52 -55.99 -43.0 Table 7-6. Radiated Spurious Data (LTE Band 14 – High Channel) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 28 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

MODULATION SIGNAL: QPSK BANDWIDTH: 5.00 MHz DISTANCE: 3 meters NARROWBAND EMISSION LIMIT: -50 dBm WIDEBAND EMISSION LIMIT: -40 dBm/MHz Ant. Antenna Turntable Level at Substitute Spurious Frequency Margin Pol. Height Azimuth Antenna Antenna Gain Emission Level [MHz] [dB] [H/V] [cm] [degree] Terminals [dBm] [dBi] [dBm] 1581.00 H 150 359 -65.28 5.93 -59.35 -19.3 1586.00 H 150 5 -65.53 5.95 -59.58 -19.6 1591.00 H 150 355 -66.17 5.96 -60.21 -20.2 Table 7-7. Radiated Spurious Data (LTE Band 14 – Wide Band) MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 29 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

7.8 Frequency Stability / Temperature Variation §2.1055 §90.213 Test Overview and Limit Frequency stability testing is performed in accordance with the guidelines of ANSI/TIA-603-D-2010. The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm) of the center frequency. Test Procedure Used ANSI/TIA-603-D-2010 Test Settings 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Test Setup The EUT was connected via an RF cable to a spectrum analyzer with the EUT placed inside an environmental chamber. Test Notes None MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 30 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Frequency Stability / Temperature Variation §2.1055, §90.213 OPERATING FREQUENCY: 793,000,000 Hz CHANNEL: 23330 REFERENCE VOLTAGE: 3.80 VDC VOLTAGE POWER TEMP FREQUENCY Freq. Dev. Deviation (%) (VDC) o (Hz) (Hz) (%) ( C) 100 % 3.80 + 20 (Ref) 792,999,838 -162 -0.0000204 100 % - 30 792,999,982 -18 -0.0000023 100 % - 20 793,000,144 144 0.0000182 100 % - 10 793,000,233 233 0.0000294 100 % 0 792,999,809 -191 -0.0000241 100 % + 10 792,999,861 -139 -0.0000175 100 % + 20 792,999,894 -106 -0.0000134 100 % + 30 792,999,682 -318 -0.0000401 100 % + 40 793,000,124 124 0.0000156 100 % + 50 792,999,954 -46 -0.0000058 BATT. ENDPOINT 3.05 + 20 792,999,748 -252 -0.0000318 Table 7-8. LTE B14 Frequency Stability Data MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 31 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

Frequency Stability 3.5 2.5 1.5 Deviation (ppm) 0.5 -0.5 -1.5 -2.5 -3.5 Tem perature (°C) Figure 7-6. Radiated Test Setup <1GHz MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 32 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.

8.0 CONCLUSION The data collected relate only to the item(s) tested and show that the LG Portable Handset FCC ID: ZNFX410AS complies with all the requirements of Parts 90 of the FCC rules and RSS-140 of the Innovation, Science and Economic Development Canada Rules. MEASUREMENT REPORT Approved by: FCC ID: ZNFX410AS (CERTIFICATION) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 33 of 33 1M1803140041-12-R1.ZNF 3/14 - 5/17/2018 Portable Handset © 2018 PCTEST Engineering Laboratory, Inc. V 8.0 03/13/2018 All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTEST.COM.


Document Created: 2018-05-18 10:39:32
Document Modified: 2018-05-18 10:39:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC