UNII Test Report

FCC ID: ZNFV30A

Test Report

Download: PDF
FCCID_3611248

PCTEST ENGINEERING LABORATORY, INC. 7185 Oakland Mills Road, Columbia, MD 21046 USA Tel. 410.290.6652 / Fax 410.290.6654 http://www.pctestlab.com MEASUREMENT REPORT FCC Part 15.407 UNII 802.11 Applicant Name: Date of Testing: LG Electronics MobileComm U.S.A 10/5/2017 1000 Sylvan Avenue Test Site/Location: Englewood Cliffs, NJ 07632 PCTEST Lab, Columbia, MD, USA United States Test Report Serial No.: 1M1710060267-02.ZNF FCC ID: ZNFV30A APPLICANT: LG Electronics MobileComm U.S.A Application Type: Class II Permissive Change Model: LG-H931 LGH931, H931, LG-H933, LGH933, LG-VS996, LGVS996, VS996, LG- Additional Model(s): US998, LGUS998, US998, H933 EUT Type: Portable Handset FCC Classification: Unlicensed National Information Infrastructure (UNII) FCC Rule Part(s): Part 15.407 Test Procedure(s): KDB 789033 D02 v01r04, KDB 662911 D01 v02r01 Class II Permissive Change: Enabling TDWR Channels This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 789033 D02 v01r04. Test results reported herein relate only to the item(s) tested. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 1 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

T A B L E O F C O N T E N T S FCC PART 15.407 MEASUREMENT REPORT ..............................................................................................................................................3 1.0 INTRODUCTION ................................................................................................................................................................................ 4 1.1 Scope .................................................................................................................................................................................... 4 1.2 PCTEST Test Location ......................................................................................................................................................... 4 2.0 PRODUCT INFORMATION ................................................................................................................................................................ 5 2.1 Equipment Description .......................................................................................................................................................... 5 2.2 Device Capabilities ............................................................................................................................................................... 5 2.3 Test Configuration ................................................................................................................................................................. 7 2.4 EMI Suppression Device(s)/Modifications ............................................................................................................................ 7 3.0 DESCRIPTION OF TESTS ................................................................................................................................................................. 8 3.1 Evaluation Procedure ............................................................................................................................................................ 8 3.2 Environmental Conditions ..................................................................................................................................................... 8 4.0 ANTENNA REQUIREMENTS ............................................................................................................................................................. 9 5.0 MEASUREMENT UNCERTAINTY ................................................................................................................................................... 10 6.0 TEST EQUIPMENT CALIBRATION DATA ....................................................................................................................................... 11 7.0 TEST RESULTS ............................................................................................................................................................................... 12 7.1 Summary ............................................................................................................................................................................. 12 7.2 26dB Bandwidth Measurement – 802.11 ............................................................................................................................ 13 7.3 UNII Output Power Measurement – 802.11 ........................................................................................................................ 20 7.4 Maximum Power Spectral Density – 802.11 ....................................................................................................................... 25 8.0 CONCLUSION .................................................................................................................................................................................. 33 FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 2 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

MEASUREMENT REPORT FCC Part 15.407 § 2.1033 General Information APPLICANT: LG Electronics MobileComm U.S.A APPLICANT ADDRESS: 1000 Sylvan Avenue Englewood Cliffs, NJ 07632, United States TEST SITE: PCTEST ENGINEERING LABORATORY, INC. TEST SITE ADDRESS: 7185 Oakland Mills Road, Columbia, MD 21046 USA FCC RULE PART(S): Part 15.407 BASE MODEL: LG-H931 FCC ID: ZNFV30A FCC CLASSIFICATION: Unlicensed National Information Infrastructure (UNII) 15532, 15482, 15490, Test Device Serial No.: Production Pre-Production Engineering 15508, 15482 DATE(S) OF TEST: 10/5/2017 TEST REPORT S/N: 1M1710060267-02.ZNF Test Facility / Accreditations Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.  PCTEST facility is an FCC registered (PCTEST Reg. No. 159966) test facility with the site description report on file and has met all the requirements specified in Section 2.948 of the FCC Rules and Industry Canada (2451B-1).  PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and Technology (NIST) under the National Voluntary Laboratory Accreditation Program (NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.  PCTEST Lab is accredited to ISO 17025-2005 by the American Association for Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry Canada Rules.  PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).  PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules and Industry Canada Standards (RSS).  PCTEST facility is an IC registered (2451B-1) test laboratory with the site description on file at Industry Canada.  PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS, CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 3 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

1.0 INTRODUCTION 1.1 Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2 PCTEST Test Location The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington, DC area. (See Figure 1-1). These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at 7185 Oakland Mills Road, Columbia, MD 21046. The site coordinates are 39o 10’23” N latitude and 76o 49’50” W longitude. The facility is 0.4 miles North of the FCC laboratory, and the ambient signal and ambient signal strength are approximately equal to those of the FCC laboratory. The detailed description of the measurement facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2014 on January 22, 2015. Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 4 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

2.0 PRODUCT INFORMATION 2.1 Equipment Description The Equipment Under Test (EUT) is the LG Portable Handset FCC ID: ZNFV30A. The test data contained in this report pertains only to the emissions due to the EUT’s UNII transmitter. 2.2 Device Capabilities This device contains the following capabilities: 850/1900 CDMA/EvDO Rev0/A, 1x Advanced (BC0, BC1), 850/1900 GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n/ac WLAN, 802.11a/n/ac UNII, Bluetooth (1x, EDR, LE), NFC Band 1 Band 2A Band 2C Band 3 Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) 36 5180 52 5260 100 5500 149 5745 : : : : : : : : 42 5210 56 5280 120 5600 157 5785 : : : : : : : : 48 5240 64 5320 144 5720 165 5825 Table 2-1. 802.11a / 802.11n / 802.11ac (20MHz) Frequency / Channel Operations Band 1 Band 2A Band 2C Band 3 Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) 38 5190 54 102 5510 5270 151 5755 : : : : : : : : 46 5230 62 118 5590 5310 159 5795 : : 142 5710 Table 2-2. 802.11n / 802.11ac (40MHz BW) Frequency / Channel Operations Band 1 Band 2A Band 2C Band 3 Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) Ch. Frequency (MHz) 42 5210 58 106 5290 5530 155 5775 : : 138 5690 Table 2-3. 802.11ac (80MHz BW) Frequency / Channel Operations FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 5 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Notes: 1. 5GHz NII operation is possible in 20MHz, and 40MHz, and 80MHz channel bandwidths. The maximum achievable duty cycles for all modes were determined based on measurements performed on a spectrum analyzer in zero-span mode with RBW = 8MHz, VBW = 50MHz, and detector = peak per the guidance of Section B)2)b) of KDB 789033 D02 v01r04. The RBW and VBW were both greater than 50/T, where T is the minimum transmission duration, and the number of sweep points across T was greater than 100. The duty cycles are as follows: Maximum Achievable Duty Cycles Duty Cycle [%] 802.11 Mode/Band ANT1 ANT2 MIMO a 94.3 94.3 94.9 n (HT20) 93.7 94.1 94.5 ac (HT20) 93.8 93.9 90.3 5GHz n (HT40) 91.3 92.1 93.6 ac (HT40) 91.9 91.9 86.7 ac (HT80) 91.4 91.5 85.8 Table 2-4. Measured Duty Cycles 2. The device employs MIMO technology. Below are the possible configurations. SISO SDM CDD WiFi Configurations ANT1 ANT2 ANT1 ANT2 ANT1 ANT2 11a       11n (20MHz)       5GHz 11n (40MHz)       11ac (80MHz)       Table 2-5. Frequency / Channel Operations = Support ;  = NOT Support SISO = Single Input Single Output SDM = Spatial Diversity Multiplexing – MIMO function CDD = Cyclic Delay Diversity - 2Tx Function Data Rate(s) Tested: 6, 9, 12, 18, 24, 36, 48, 54Mbps (802.11a) 6.5/7.2, 13/14.4, 19.5/21.7, 26/28.9, 39/43.3, 52/57.8, 58.5/65, 65/72.2 (n/ac – 20MHz) 13.5/15, 27/30, 40.5/45, 54/60, 81/90, 108/120, 121.5/135, 135/150 (n/ac – 40MHz BW) 29.3/32.5, 58.5/65, 87.8/97.5, 117/130, 175.5/195, 234/260, 263.3/292.5, 292.5/325, 351/390, 390/433.3 (ac – 80MHz BW) 13/14.4, 26.28.9, 39/43.3, 52/57.8, 78/86.7, 104/115.6, 117/130, 130/144.4MBps (MIMO n/ac – 20MHz) 156/173Mbps (MIMO ac – 20MHz) 27/30, 54/60, 81/90, 108/120, 162/180, 216/240, 243,270, 270/300Mbps (MIMO n/ac – 40MHz) 324/360, 360/400Mbps (MIMO ac – 40MHz) 58.5/65, 117/130, 175.5/195, 234/260, 351/390, 468/520, 526.5/585, 585/650, 702/780, 780/866.7Mbps (MIMO ac – 80MHz) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 6 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

3. This device supports simultaneous transmission operation, which allows for two SISO channels to operate independent of one another in the 2.4GHz and 5GHz bands simultaneously on Antenna 1 and Antenna 2 respectively. Table 2-6 shows the worst case configuration determined during testing. The data for these configurations is contained in this test report. Configuration 1: ANT1 transmitting in 2.4GHz mode and ANT2 in 5GHz mode Description 2.4 GHz Emission 5 GHz Emission Antenna 1 2 Channel 6 48 Operating Frequency (MHz) 2437 5380 Data Rate (Mbps) MCS0 MCS0 Mode 802.11n 802.11n Table 2-6. Config-1 (ANT1 2.4GHz & ANT2 5GHz) 2.3 Test Configuration The EUT was tested per the guidance of KDB 789033 D02 v01r04. See Sections 7.2,7.3, and 7.4 for antenna port conducted emissions test setups. 2.4 EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 7 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

3.0 DESCRIPTION OF TESTS 3.1 Evaluation Procedure The measurement procedures described in the American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices (ANSI C63.10-2013) and the guidance provided in KDB 789033 D02 v01r04 were used in the measurement of the EUT. Deviation from measurement procedure……………………………………...……………..........................None 3.2 Environmental Conditions The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of 10% to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar). FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 8 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

4.0 ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antennas of the EUT are permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The EUT complies with the requirement of §15.203. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 9 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

5.0 MEASUREMENT UNCERTAINTY The measurement uncertainties shown below were calculated in accordance with the requirements of ANSI C63.10-2013. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a 95% level of confidence. The measurement uncertainty shown below meets or exceeds the UCISPR measurement uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to determine compliance. Contribution Expanded Uncertainty (±dB) Conducted Bench Top 1.13 Measurements FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 10 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

6.0 TEST EQUIPMENT CALIBRATION DATA Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST). Measurements antennas used during testing were calibrated in accordance to the requirements of ANSI C63.5-2006. Manufacturer Model Description Cal Date Cal Interval Cal Due Serial Number Agilent N9020A MXA Signal Analyzer 10/28/2016 Annual 10/28/2017 US46470561 Anritsu ML2495A Power Meter 10/16/2015 Biennial 10/16/2017 941001 Seekonk NC‐100 Torque Wrench 5/16", 8" lbs 3/2/2016 Biennial 3/2/2018 N/A ‐ WL25‐1 Conducted Cable Set (25GHz) 6/14/2017 Annual 6/14/2018 WL25‐1 Agilent N9030A PXA Signal Analyzer (44GHz) 3/27/2017 Annual 3/27/2018 MY52350166 Anritsu ML2495A Power Meter 10/16/2015 Biennial 10/16/2017 1328004 Anritsu ML2496A Power Meter 6/8/2017 Annual 6/8/2018 1405003 Table 6-1. Annual Test Equipment Calibration Schedule for Conducted Measurements Note: For equipment listed above that has a calibration date or calibration due date that falls within the test date range, care was taken to ensure that this equipment was used after the calibration date and before the calibration due date. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 11 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

7.0 TEST RESULTS 7.1 Summary Company Name: LG Electronics MobileComm U.S.A FCC ID: ZNFV30A Method/System: Unlicensed National Information Infrastructure (UNII) FCC Part Test Test Test Description Test Limit Reference Section(s) Condition Result N/A 26dB Bandwidth N/A PASS Section 7.2 15.407 (a.1.iv), Maximum Conducted Maximum conducted powers must meet CONDUCTED PASS Section 7.3 (a.2), (a.3) Output Power the limits detailed in 15.407 (a) 15.407 (a.1.iv), Maximum Power Spectral Maximum power spectral density must PASS Section 7.4 (a.2), (a.3) Density meet the limits detailed in 15.407 (a) Table 7-1. Summary of Test Results Notes: 1) All channels, modes, and modulations/data rates were investigated among all UNII bands. The test results shown in the following sections represent the worst case emissions. 2) The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 3) All antenna port conducted emissions testing was performed on a test bench with the antenna port of the EUT connected to the spectrum analyzer through calibrated cables and attenuators. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 12 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

7.2 26dB Bandwidth Measurement – 802.11 Test Overview and Limit The bandwidth at 26dB down from the highest in-band spectral density is measured with a spectrum analyzer connected to the antenna terminal while the EUT is operating at its maximum duty cycle, at its maximum power control level, as defined in KDB 789033 D02 v01r04, and at the appropriate frequencies. The spectrum analyzer’s bandwidth measurement function is configured to measure the 26dB bandwidth. The 26dB bandwidth is used to determine the conducted power limits. Test Procedure Used KDB 789033 D02 v01r04 – Section C Test Settings 1. The signal analyzers’ automatic bandwidth measurement capability was used to perform the 26dB bandwidth measurement. The “X” dB bandwidth parameter was set to X = 26. The automatic bandwidth measurement function also has the capability of simultaneously measuring the 99% occupied bandwidth. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. 2. RBW = approximately 1% of the emission bandwidth 3. VBW > 3 x RBW 4. Detector = Peak 5. Trace mode = max hold Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-1. Test Instrument & Measurement Setup Test Notes None. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 13 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Antenna-1 26 dB Bandwidth Measurements Measured 26dB Frequency Channel 802.11 Mode Data Rate [Mbps] Bandwidth [MHz] No. [MHz] Band 2C 5600 120 a 6 21.47 5600 120 n (20MHz) 6.5/7.2 (MCS0) 21.21 5590 118 n (40MHz) 13.5/15 (MCS0) 39.92 5610 122 ac (80MHz) 29.3/32.5 (MCS0) 81.22 Table 7-2. Conducted Bandwidth Measurements FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 14 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-1. 26dB Bandwidth Plot (802.11a (UNII Band 2C) – Ch. 120) Plot 7-2. 26dB Bandwidth Plot (20MHz BW 802.11n (UNII Band 2C) – Ch. 120) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 15 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-3. 26dB Bandwidth Plot (40MHz BW 802.11n (UNII Band 2C) – Ch. 118) Plot 7-4. 26dB Bandwidth Plot (80MHz BW 802.11ac (UNII Band 2C) – Ch. 122) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 16 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Antenna-2 26dB Bandwidth Measurements Measured 26dB Frequency Channel 802.11 Mode Data Rate [Mbps] Bandwidth [MHz] No. [MHz] Band 2C 5600 120 a 6 21.55 5600 120 n (20MHz) 6.5/7.2 (MCS0) 21.77 5590 118 n (40MHz) 13.5/15 (MCS0) 39.88 5610 122 ac (80MHz) 29.3/32.5 (MCS0) 81.59 Table 7-3. Conducted Bandwidth Measurements FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 17 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-5. 26dB Bandwidth Plot (802.11a (UNII Band 2C) – Ch. 120) Plot 7-6. 26dB Bandwidth Plot (20MHz BW 802.11n (UNII Band 2C) – Ch. 120) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 18 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-7. 26dB Bandwidth Plot (40MHz BW 802.11n (UNII Band 2C) – Ch. 118) Plot 7-8. 26dB Bandwidth Plot (80MHz BW 802.11ac (UNII Band 2C) – Ch. 122) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 19 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

7.3 UNII Output Power Measurement – 802.11 §15.407(a.1.iv) §15.407(a.2) §15.407(a.3) Test Overview and Limits A transmitter antenna terminal of the EUT is connected to the input of an RF pulse power sensor. Measurement is made using a broadband average power meter while the EUT is operating at its maximum duty cycle, at its maximum power control level, as defined in KDB 789033 D02 v01r04, and at the appropriate frequencies. In the 5.47 – 5.725GHz band, the maximum permissible conducted output power is the lesser of 250mW (23.98dBm) and 11 dBm + 10log10(26dB BW) = 11 dBm + 10log10(21.93) = 24.41dBm. Test Procedure Used KDB 789033 D02 v01r04 – Section E)3)b) Method PM-G KDB 662911 v02r01 – Section E)1) Measure-and-Sum Technique Test Settings Average power measurements were performed only when the EUT was transmitting at its maximum power control level using a broadband power meter with a pulse sensor. The power meter implemented triggering and gating capabilities which were set up such that power measurements were recorded only during the ON time of the transmitter. The trace was averaged over 100 traces to obtain the final measured average power. Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-2. Test Instrument & Measurement Setup Test Notes None FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 20 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Antenna-1 Conducted Output Power Measurements 5GHz (20MHz) Conducted Power [dBm] IEEE Transmission Mode Freq [MHz] Channel 802.11a 802.11n 802.11ac 5600 120 16.49 16.39 16.24 5620 124 16.47 16.38 16.39 5640 128 16.49 16.16 16.21 Table 7-4. 20MHz BW (UNII) Maximum Conducted Output Power 5GHz (40MHz) Conducted Power [dBm] IEEE Transmission Mode Freq [MHz] Channel 802.11n 802.11ac 5590 118 15.50 15.50 5630 126 15.39 15.26 Table 7-5. 40MHz BW (UNII) Maximum Conducted Output Power 5GHz (80MHz) Conducted Power [dBm] IEEE Transmission Freq [MHz] Channel Mode 802.11ac 5610 122 11.53 Table 7-6. 80MHz BW (UNII) Maximum Conducted Output Power FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 21 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Antenna-2 Conducted Output Power Measurements 5GHz (20MHz) Conducted Power [dBm] IEEE Transmission Mode Freq [MHz] Channel 802.11a 802.11n 802.11ac 5600 120 15.78 15.61 15.61 5620 124 15.73 15.81 15.89 5640 128 15.72 15.72 15.31 Table 7-7. 20MHz BW (UNII) Maximum Conducted Output Power 5GHz (40MHz) Conducted Power [dBm] IEEE Transmission Mode Freq [MHz] Channel 802.11n 802.11ac 5590 118 14.98 14.93 5630 126 14.58 14.57 Table 7-8. 40MHz BW (UNII) Maximum Conducted Output Power 5GHz (80MHz) Conducted Power [dBm] IEEE Transmission Freq [MHz] Channel Mode 802.11ac 5610 122 11.07 Table 7-9. 80MHz BW (UNII) Maximum Conducted Output Power FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 22 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

MIMO Maximum Conducted Output Power Measurements 5GHz (20MHz) Conducted Power [dBm] Freq [MHz] Channel ANT1 ANT2 MIMO 5600 120 16.49 15.78 19.16 5620 124 16.47 15.73 19.13 5640 128 16.49 15.72 19.13 Table 7-10. CDD 20MHz BW 802.11a (UNII) Maximum Conducted Output Power 5GHz (20MHz) Conducted Power [dBm] Freq [MHz] Channel ANT1 ANT2 MIMO 5600 120 16.39 15.61 19.03 5620 124 16.38 15.81 19.11 5640 128 16.16 15.72 18.96 Table 7-11. MIMO 20MHz BW 802.11n (UNII) Maximum Conducted Output Power 5GHz (20MHz) Conducted Power [dBm] Freq [MHz] Channel ANT1 ANT2 MIMO 5600 120 16.24 15.61 18.95 5620 124 16.39 15.89 19.16 5640 128 16.21 15.31 18.79 Table 7-12. MIMO 20MHz BW 802.11ac (UNII) Maximum Conducted Output Power 5GHz (40MHz) Conducted Power [dBm] Freq [MHz] Channel ANT1 ANT2 MIMO 5590 118 15.50 14.98 18.26 5630 126 15.39 14.58 18.01 Table 7-13. MIMO 40MHz BW 802.11n (UNII) Maximum Conducted Output Power 5GHz (40MHz) Conducted Power [dBm] Freq [MHz] Channel ANT1 ANT2 MIMO 5590 118 15.50 14.93 18.23 5630 126 15.26 14.57 17.94 Table 7-14. MIMO 40MHz BW 802.11ac (UNII) Maximum Conducted Output Power 5GHz (80MHz) Conducted Power [dBm] Freq [MHz] Channel ANT1 ANT2 MIMO 5610 122 11.53 11.07 14.32 Table 7-15. MIMO 80MHz BW 802.11ac (UNII) Maximum Conducted Output Power Note: Per KDB 662911 v02r01 Section E)1), the conducted powers at Antenna 1 and Antenna 2 were first measured separately during MIMO transmission as shown in the section above. The measured values were then summed in linear power units then converted back to dBm. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 23 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Sample MIMO/CDD Calculation: At 5600MHz n mode, the average conducted output power was measured to be 16.39 dBm for Antenna-1 and 15.61 dBm for Antenna-2. Antenna 1 + Antenna 2 = MIMO ( 16.39 dBm + 15.61 dBm) = ( 43.55 mW + 36.39 mW) = 79.94 mW = 19.03 dBm FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 24 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

7.4 Maximum Power Spectral Density – 802.11 §15.407(a.1.iv) §15.407(a.2) §15.407(a.3) Test Overview and Limit The spectrum analyzer was connected to the antenna terminal while the EUT was operating at its maximum duty cycle, at its maximum power control level, as defined in KDB 789033 D02 v01r04, and at the appropriate frequencies. Method SA-1, as defined in KDB 789033 D02 v01r04, was used to measure the power spectral density. In the 5.15 – 5.25GHz, 5.25 – 5.35GHz, 5.47 – 5.725GHz bands, the maximum permissible power spectral density is 11dBm/MHz. In the 5.725 – 5.850GHz band, the maximum permissible power spectral density is 30dBm/500kHz. Test Procedure Used KDB 789033 D02 v01r04 – Section F KDB 662911 v02r01 – Section E)2) Measure-and-Sum Technique Test Settings 1. Analyzer was set to the center frequency of the UNII channel under investigation 2. Span was set to encompass the entire emission bandwidth of the signal 3. RBW = 1MHz 4. VBW = 3MHz 5. Number of sweep points > 2 x (span/RBW) 6. Sweep time = auto 7. Detector = power averaging (RMS) 8. Trigger was set to free run for all modes 9. Trace was averaged over 100 sweeps 10. The peak search function of the spectrum analyzer was used to find the peak of the spectrum. Test Setup The EUT and measurement equipment were set up as shown in the diagram below. Figure 7-3. Test Instrument & Measurement Setup Test Notes None FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 25 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Antenna-1 Power Spectral Density Measurements Measured Max Permissible Frequency Channel Margin 802.11 Mode Data Rate [Mbps] Power Density Power Density [MHz] No. [dB] [dBm] [dBm/MHz] 5600 120 a 6 6.89 11.0 -4.11 Band 2C 5600 120 n (20MHz) 6.5/7.2 (MCS0) 6.42 11.0 -4.58 5590 118 n (40MHz) 13.5/15 (MCS0) 2.82 11.0 -8.18 5610 122 ac (80MHz) 29.3/32.5 (MCS0) -3.14 11.0 -14.14 Table 7-16. Bands 2C Conducted Power Spectral Density Measurements FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 26 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-9. Power Spectral Density Plot (802.11a (UNII Band 2C) – Ch. 120) Plot 7-10. Power Spectral Density Plot (20MHz BW 802.11n (UNII Band 2C) – Ch. 120) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 27 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-11. Power Spectral Density Plot (40MHz BW 802.11n (UNII Band 2C) – Ch. 118) Plot 7-12. Power Spectral Density Plot (80MHz BW 802.11ac (UNII Band 2C) – Ch. 122) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 28 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Antenna-2 Power Spectral Density Measurements Measured Max Permissible Frequency Channel Margin 802.11 Mode Data Rate [Mbps] Power Density Power Density [MHz] No. [dB] [dBm] [dBm/MHz] 5600 120 a 6 6.16 11.0 -4.85 Band 2C 5600 120 n (20MHz) 6.5/7.2 (MCS0) 5.61 11.0 -5.39 5590 118 n (40MHz) 13.5/15 (MCS0) 2.31 11.0 -8.69 5610 122 ac (80MHz) 29.3/32.5 (MCS0) -3.58 11.0 -14.58 Table 7-17. Bands 2C Conducted Power Spectral Density Measurements FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 29 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-13. Power Spectral Density Plot (802.11a (UNII Band 2C) – Ch. 120) Plot 7-14. Power Spectral Density Plot (20MHz BW 802.11n (UNII Band 2C) – Ch. 120) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 30 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Plot 7-15. Power Spectral Density Plot (40MHz BW 802.11n (UNII Band 2C) – Ch. 118) Plot 7-16. Power Spectral Density Plot (80MHz BW 802.11ac (UNII Band 2C) – Ch. 122) FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 31 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

Summed MIMO/CDD Power Spectral Density Measurements Antenn-1 Antenn-2 Summed MIMO Max Permissible Frequency Channel Margin 802.11 Mode Data Rate [Mbps] Power Density Power Density Power Density Power Density [MHz] No. [dB] [dBm] [dBm] [dBm] [dBm/MHz] 5600 120 a 6.5/7.2 (MCS0) 6.89 6.16 9.55 11.0 -1.45 Band 2C 5600 120 n (20MHz) 6.5/7.2 (MCS0) 6.42 5.61 9.05 11.0 -1.95 5590 118 n (40MHz) 13.5/15 (MCS0) 2.82 2.31 5.59 11.0 -5.41 5610 122 ac (80MHz) 29.3/32.5 (MCS0) -3.14 -3.58 -0.34 11.0 -11.34 Table 7-18. Bands 2C MIMO/CDD Conducted Power Spectral Density Measurements Note: Per KDB 662911 v02r01 Section E)2), the power spectral density at Antenna 1 and Antenna 2 were first measured separately as shown in the section above. The measured values were then summed in linear power units then converted back to dBm. Sample MIMO/CDD Calculation: At 5600MHz n mode, the average conducted power spectral density was measured to be 6.89 dBm for Antenna-1 and 6.16 dBm for Antenna-2. Antenna 1 + Antenna 2 = MIMO (6.89 dBm + 6.16 dBm) = (4.89 mW + 4.13 mW) = 9.02 mW = 9.55 dBm FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 32 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.

8.0 CONCLUSION The data collected relate only the item(s) tested and show that the LG Portable Handset FCC ID: ZNFV30A is in compliance with Part 15E of the FCC Rules. FCC Pt. 15.407 802.11 UNII MEASUREMENT REPORT Approved by: FCC ID: ZNFV30A (CLASS II PERMISSIVE CHANGE) Quality Manager Test Report S/N: Test Dates: EUT Type: Page 33 of 33 1M1710060267-02.ZNF 10/5/2017 Portable Handset © 2017 PCTEST Engineering Laboratory, Inc. V 6.8 07/14/2017 © 2017 PCTEST Engineering Laboratory, Inc. All rights reserved. Unless otherwise specified, no part of this report may be reproduced or utilized in any part, form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from PCTEST Engineering Laboratory, Inc. If you have any questions about this international copyright or have an enquiry about obtaining additional rights to this report or assembly of contents thereof, please contact INFO@PCTESTLAB.COM.


Document Created: 2019-10-16 18:42:27
Document Modified: 2019-10-16 18:42:27
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC