DFS Test Report

FCC ID: ZNFH960

Test Report

Download: PDF
FCCID_2762515

74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Korea TEL: +82-31-645-6300 FAX: +82-31-645-6401 FCC DFS REPORT FCC Certification Applicant Name: Date of Issue: LG Electronics MobileComm U.S.A., Inc. September 08, 2015 Test Site/Location: HCT CO., LTD., 74, Seoicheon-ro 578beon-gil, Majang- Address: myeon, Icheon-si, Gyeonggi-do, Korea 1000 Sylvan Avenue, Englewood Cliffs NJ 07632 Report No.: HCT-R-1509-F021 HCT FRN: 0005866421 FCC ID : ZNFH960 APPLICANT : LG Electronics MobileComm U.S.A., Inc. FCC Model(s): LG-H960 Additional Model(s): LGH960, H960, LG-H960P, LGH960P, H960P, LG-H960AR, LGH960AR, H960AR, LG-H960YK, LGH960YK, H960YK EUT Type: Cellular/PCS GSM/WCDMA/LTE Phone with WLAN, Bluetooth and NFC Max. RF Channel Frequency Output Power Power Power Band Mode Bandwidth Range (Average): (dBm) (W) (MHz) (MHz) 802.11a 20 5260 – 5320 14.62 0.0290 802.11n 20 5260 – 5320 14.30 0.0269 802.11n 40 5270 – 5310 12.77 0.0189 UNII2A 802.11ac 20 5260 – 5320 15.14 0.0327 802.11ac 40 5270 – 5310 12.80 0.0191 802.11ac 80 5290 12.00 0.0158 802.11a 20 5500 – 5720 14.00 0.0251 802.11n 20 5500 – 5720 13.59 0.0229 802.11n 40 5510 – 5710 12.50 0.0178 UNII2C 802.11ac 20 5500 – 5720 14.51 0.0282 802.11ac 40 5510 – 5710 12.51 0.0178 802.11ac 80 5530 – 5690 12.30 0.0170 Frequency Range: 20MHz :5260 MHz - 5320 MHz (UNII 2A)/ 5500 MHz - 5720 MHz (UNII 2C) 40MHz :5270 MHz - 5310 MHz (UNII 2A)/ 5510 MHz - 5670 MHz (UNII 2C) 80MHz: 5290 MHz(UNII 2A)/ 5530 MHz - 5690 MHz(UNII 2C) Modulation type OFDM FCC Classification: Unlicensed National Information Infrastructure (UNII) FCC Rule Part(s): Part 15.407(DFS) F-01P-02-014 (Rev.00) HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ２ of 23 Model: LG-H960 Engineering Statement: The measurements shown in this report were made in accordance with the procedures indicated, and the emissions from this equipment were found to be within the limits applicable. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. HCT CO., LTD. Certifies that no party to this application has subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1998,21 U.S. C.853(a) Report prepared by Approved by : Kyung Soo Kang : Sang Jun Lee Test Engineer of RF Team Manager of RF Team This report only responds to the tested sample and may not be reproduced, except in full, without written approval of the HCT Co., Ltd. F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ３ of 23 Model: LG-H960 Version TEST REPORT NO. DATE DESCRIPTION HCT-R-1509-F021 September 08, 2015 - First Approval Report F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ４ of 23 Model: LG-H960 Table of Contents 1. GENERAL INFORMATION .......................................................................................................................... ５ 2. EUT DESCRIPTION ..................................................................................................................................... ５ 3. SCOPE ......................................................................................................................................................... ６ 4. INSTRUMENT CALIBRATION..................................................................................................................... ６ 5. FACILITIES AND ACCREDITATIONS ......................................................................................................... ６ 5.1 FACILITIES ......................................................................................................................................... ６ 5.2 EQUIPMENT ....................................................................................................................................... ６ 6. SUMMARY OF TEST RESULTS ................................................................................................................. ７ 7. DESCRIPTION OF DYNAMIC FREQUENCY SELECTION TEST.............................................................. ８ 7.1 APPLICABILITY ................................................................................................................................. ８ 7.2 REQUIREMENTS................................................................................................................................ ９ 7.3 DFS DETECTION THRESHOLD VALUES .................................................................................... １１ 7.4 PARAMETERS OF DFS TEST SIGNALS...................................................................................... １２ 7.5 TEST AND MEASUREMENT SYSTEM ......................................................................................... １４ 7.6 DESCRIPTION OF EUT.................................................................................................................. １６ 7.7 UNII2A TEST RESULT ................................................................................................................... １７ 7.8 UNII2C TEST RESULT ................................................................................................................... ２０ 8. LIST OF TEST EQUIPMENT ................................................................................................................... ２３ F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ５ of 23 Model: LG-H960 1. GENERAL INFORMATION Applicant: LG Electronics MobileComm U.S.A., Inc Address: 1000 Sylvan Avenue, Englewood Cliffs NJ 07632 FCC ID: ZNFH960 EUT Type: Cellular/PCS GSM/WCDMA/LTE Phone with WLAN, Bluetooth and NFC Model name(s): LG-H960 Date(s) of Tests: August 12, 2015 ~ September 8, 2015 Place of Tests: HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Korea. (IC Recognition No. : 5944A-3) 2. EUT DESCRIPTION FCC Model Name LG-H960 LGH960, H960, LG-H960P, LGH960P, H960P, LG-H960AR, LGH960AR, H960AR, Additional Model(s): LG-H960YK, LGH960YK, H960YK EUT Type Cellular/PCS GSM/WCDMA/LTE Phone with WLAN, Bluetooth and NFC Power Supply DC 3.85 V Model: BL-45B1F Battery Infomation Type: Li-ion Battery(Standard) TX_20 MHz BW: 5260 MHz - 5320 MHz (UNII 2A)/ 5500 MHz - 5720 MHz (UNII 2C) TX_40 MHz BW: 5270 MHz - 5310 MHz (UNII 2A)/ 5510 MHz - 5710 MHz (UNII 2C) TX_80 MHz BW: 5290 MHz(UNII 2A)/ 5530 MHz - 5690 MHz(UNII 2C) Frequency Range RX_20 MHz BW: 5260 MHz - 5320 MHz (UNII 2A)/ 5500 MHz - 5720 MHz (UNII 2C) RX_40 MHz BW: 5270 MHz - 5310 MHz (UNII 2A)/ 5510 MHz - 5710 MHz (UNII 2C) RX_80 MHz BW: 5290 MHz(UNII 2A)/ 5530 MHz - 5690 MHz(UNII 2C) Modulation Type OFDM(802.11a, 802.11n, 802.11ac) Antenna Specification Manufacturer: LS Mtron Co. Ltd. Antenna type: INTERNAL ANTENNA Peak Gain : -0.95 dBi (5260~5325 UNII2A BAND) / -3.79 dBi (5500~5720 UNII2C BAND) F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ６ of 23 Model: LG-H960 3. SCOPE This report has been prepared to demonstrate compliance with the requirements for Dynamic Frequency Selection(DFS) as stated in KDB 905462 D02 v01r02. Testing was performed in accordance with the measurement procedure described in FCC KDB 905462 D02 v01. 4. INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipments, which is traceable to recognized national standards. 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES The SAC(Semi-Anechoic Chamber) and conducted measurement facility used to collect the radiated data are located at the 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, Korea The site is constructed in conformance with the requirements of ANSI C63.4. (Version :2014) and CISPR Publication 22. Detailed description of test facility was submitted to the Commission and accepted dated July 07, 2015 (Registration Number: 90661) / June 22, 2015 (IC egistration Number: 5944A-5) 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of Linearly polarized antennas: tuned dipole, bi-conical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ７ of 23 Model: LG-H960 6. SUMMARY OF TEST RESULTS Band Parameter Limit Result Channel Move Time 10 seconds PASS 200 ms + aggregate of 60 ms over UNII2A Channel Closing Transmission Time PASS remaining 10 second period Non-occupancy Period 30 minutes PASS Channel Move Time 10 seconds PASS 200 ms + aggregate of 60 ms over UNII2C Channel Closing Transmission Time PASS remaining 10 second period Non-occupancy Period 30 minutes PASS F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ８ of 23 Model: LG-H960 7. DESCRIPTION OF DYNAMIC FREQUENCY SELECTION TEST 7.1 APPLICABILITY The following table from KDB905462 D02(05/15/2015) lists the applicable requirements for the DFS testing. The device evaluated in this report is considered a client device without radar detection capability. Operation Mode Requirement Client Without Radar Client With Radar Master Detection Detection Non-Occupancy Period Yes Not required Yes DFS Detection Threshold Yes Not required Yes Channel Availability Check Time Yes Not required Not required Uniform Spreading Yes Not required Not required U-NII Detection Bandwidth Yes Not required Yes Table 1-1. DFS Applicability Operation Mode Requirement Client Without Radar Client With Radar Master Detection Detection DFS Detection Threshold Yes Not required Yes Channel Closing Transmission Time Yes Yes Yes Channel Move Time Yes Yes Yes U-NII Detection Bandwidth Yes Not required Yes Table 1-2. DFS Applicability During Normal Operation F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ９ of 23 Model: LG-H960 7.2 REQUIREMENTS Per KDB905462 D02(05/15/2015) the following are the requirements for Client Devices: a) A Client Device will not transmit before having received appropriate control signals from a Master Device. b) A Client Device will stop all its transmissions whenever instructed by a Master Device to which it is associated and will meet the Channel Move Time and Channel Closing Transmission Time requirements. The Client Device will not resume any transmissions until it has again received control signals from a Master Device. c) If a Client Device is performing In-Service Monitoring and detects a Radar Waveform above the DFS Detection Threshold, it will inform the Master Device. This is equivalent to the Master Device detecting the Radar Waveform and d) through f) of section 5.1.1 apply. d) Irrespective of Client Device or Master Device detection the Channel Move Time and Channel Closing Transmission Time requirements remain the same. F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １０ of 23 Model: LG-H960 Channel Move Time and Channel Closing Transmission Time requirements are listed following table. Parameter Value Non-occupancy period Minimum 30 minutes Channel Availability Check Time 60 seconds 10 seconds Channel Move Time See Note 1. 200 milliseconds + an Aggregate of 60 milliseconds over Channel Closing Transmission Time Remaining 10 second period. See Notes 1 and 2. Minimum 100 % of the U-NII U-NII Detection Bandwidth 99 % transmission Power bandwidth. See Note 3. Note 1: Channel Move Time and the Channel Closing Transmission Time should be performed with Radar Type 0. The measurement timing begins at the end of the Radar Type 0 burst. Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of The Channel Move Time plus any additional intermittent control signals required to facilitate a Channell move (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The aggregate duration of control signals will not count quiet periods in between transmissions. Note3: During the U-NII Detection Bandwidth detection test, radar type 0 should be used. For each frequency step the minimum percentage of detection is 90 percent. Measurements are performed With no data traffic. Table 1-3: DFS Response requirements F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １１ of 23 Model: LG-H960 7.3 DFS DETECTION THRESHOLD VALUES The DFS detection thresholds are defined for Master devices and Client Devices with In-service monitoring. These detection thresholds are listed in the following table. Value Maximum Transmit Power (See Notes 1 and 2) ≥ 200 milliwatt -64 dBm < 200 milliwatt -62 dBm Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna. Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the test transmission waveforms to account for variations in measurement equipment. This will ensure that the test signal is at or above the detection threshold level to trigger a DFS response. Table 1-4: Detection Thresholds for Master Devices and Client Devices with Radar Detection F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １２ of 23 Model: LG-H960 7.4 PARAMETERS OF DFS TEST SIGNALS As the EUT is a Client Device with no Radar Detection only one type radar pulse is required for the testing. Radar Pulse type 0 was used in the evaluation of the Client device for the purpose of measuring the Channel Move Time and the Channel Closing Transmission Time. Table 1-5 lists the parameters for the Short Pulse Radar Waveforms. A plot of the Radar pulse Type 0 used for testing is included in Section 7.7 of this report. F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １３ of 23 Model: LG-H960 Minimum Pulse Number Percentage Minimum PRI Radar Type Width Of of Number of (μsec) (μsec) Pulses Successful Trials Detection 0 1 1428 18 See Note 1 See Note 1 Test A: 15 unique Roundup 1 60% 30 PRI values 360 6 Randomly selected 19·10 From the list of 23 PRI µsec PRI values in Table 5a Test B: 15 unique PRI values Randomly selected 1 1 within the range of 518-3066 µ sec, with a minimum increment of 1 µ sec, excluding PRI values selected in Test A 2 1-5 150-230 23-29 60% 30 3 6-10 200-500 16-18 60% 30 4 11-20 200-500 12-16 60% 30 80% 120 Note1: Short pulse Radar Type 0 should be used for the detection bandwidth test, channel move time, and channel closing time tests. Table 1-5: Parameters for Short Pulse Radar Waveforms F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １４ of 23 Model: LG-H960 7.5 TEST AND MEASUREMENT SYSTEM General Test Setup Procedure: 1. The EUT was operating 802.11a mode (18Mbps) during the test. 2. Connect FCC approved Master AP to a network, via wired Ethernet, that allows connection to an FTP server. 3. Associate the EUT with the Master AP. 4. Launch the FTP application on the EUT. 5. Connect to the FTP server application to the FTP server hosting the file 6. Initiate an FTP download of the file from the host. 7. Monitor the channel loading during transfer. 8. Reduce the maximum allowed data rate for the Master AP, using the AP’s GUI interface. 9. Repeat steps 5-7 until the channel loading is as close to 20 % as possible. 10. Record the data rate setting on the Master AP and the channel loading. 11. While the system is performing an FTP transfer using the settings form item 9 above, perform the Channel Closing Transmission Time and Channel Move Time Measurements as required by KDB905462 D02(05/15/2015) using a conducted test. PROCEDURE The KDB905462 D02(05/15/2015) describes a radiated test setup and a conducted test setup. A radiated test setup was used for this testing. Figure 3-1 shows the typical test setup. Each one channel selected between 5260 and 5320 MHz, 5500 and 5720 is chosen for the testing. Figure 3-1. Conducted Test Setup for DFS F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １５ of 23 Model: LG-H960 1. The radar pulse generator is setup to provide a pulse at the frequency that the Master and Client are operating. A Type 0 radar pulse with a 1 μs pulse width and a 1428 μs PRI is used for the testing. 2. The vector signal generator is adjusted to provide the radar burst (18 pulses) at a level of approximately -62 dBm at the antenna of the Master device. 3. The Client Device (EUT) is set up per the diagram in Figure 3-1 and communications between the Master device and the Client is established. 4. The MPEG file specified by the FCC (”6½ Magic Hours”) is streamed from the “file computer” through the Master to the Slave Device and played in full motion video using Media Player Classic Ver.6.4.8.6 in order to properly load the network. 5. The real time spectrum analyzer is set to record about 15 sec window to any transmissions occurring up to and after 10 sec. 6. The system is again setup and the monitoring time is shortened in order to capture the Channel Closing Transmission Time. This time is measured to insure that the Client ceases transmission within 200 ms and the aggregate of emissions occurring after 200 ms up to 10 sec do not exceed 60 ms. (Note: the channel may be different since the Master and Client have changed channels due to the detection of the initial radar pulse.) 7. After the initial radar burst the channel is monitored for 30 minutes to insure no transmissions or beacons occur. A second monitoring setup is used to verify that the Master and Client have both moved to different channels. SYSTEM CALIBRATION A-50-ohm load is connected in place of the spectrum analyzer, and the spectrum analyzer is connected to a coaxial cable. The signal generator is set to CW mode. The amplitude of the signal generator is adjusted to yield a level of - 62 dBm as measured on the spectrum analyzer. Without changing any of the instrument settings, the spectrum analyzer is reconnected to the common port of the spectrum analyzer combiner or divider. The spectrum analyzer displays the level of the signal generator higher than the client TX level. Because we can not search the signal generator in the spectrum analyzer when the signal generator level is - 62 dBm. The spectrum analyzer will still indicate the level higher than the client TX level. F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １６ of 23 Model: LG-H960 7.6 DESCRIPTION OF EUT The EUT operates over the 5260 MHz - 5320 MHz and 5500 MHz - 5720 MHz ranges. The EUT is a slave device without radar detection. The EUT antenna has a gain of -0.95 dBi in 5260 MHz - 5320 MHz band and -3.79 dBi in 5500 MHz- 5720 MHz band. The highest power level within these bands in 14.19 dBm EIRP in the 5260 MHz - 5320 MHz band and 10.72 dBm EIRP in the 5500 MHz – 5720 MHz band. The EUT one transmitter/receiver chain connected to a coaxial cable to perform conducted tests. TPC is not required since the maximum EIRP is less than 500 mW. The EUT utilizes the 802.11a/n/ac architecture. Three nominal channel bandwidth is implemented: 20 MHz, 40 MHz and 80 MHz F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １７ of 23 Model: LG-H960 7.7 UNII2A TEST RESULT ▣ RESULT PLOTS(UNII2A Band) Type0 Radar Pulse Number – Ch.60 Marker Descriptions: Number of Pulse Form M1R to M1 : 18 Type0 PRI F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １８ of 23 Model: LG-H960 Time Display, Non WLAN Channel Traffic Time Display, WLAN Channel Traffic (Streaming Video) F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page １９ of 23 Model: LG-H960 ㆍChannel Move Time : 0.156022 s(Limit : 10 s) ㆍChannel Closing Transmission Time, Aggregate Time After 200 ms : 0.000270 s(Limit : 60 ms) Non-occupancy Period – Monitoring live real time spectrum – Elapse time 30 minutes F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ２０ of 23 Model: LG-H960 7.8 UNII2C TEST RESULT ▣ RESULT PLOTS_(UNII2C Band) Type0 Radar Pulse Number – Ch.100 Marker Descriptions: Number of Pulse Form M1R to M1 : 18 Type0 PRI F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ２１ of 23 Model: LG-H960 Time Display, Non WLAN Channel Traffic Time Display, WLAN Channel Traffic (Streaming Video) F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ２２ of 23 Model: LG-H960 ㆍChannel Move Time : 0.136564 s(Limit : 10 s) ㆍChannel Closing Transmission Time, Aggregate Time After 200 ms : 0.000413 s(Limit : 60 ms) Non-occupancy Period – Monitoring live real time spectrum – Elapse time 30 minutes F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.

Report No.: HCT-R-1509-F021 Page ２３ of 23 Model: LG-H960 8. LIST OF TEST EQUIPMENT Calibration Calibration Manufacturer Model / Equipment Serial No. Date Interval S2LF812265 SAMSUNG WEA453e / Wireless AP N/A N/A FCC ID: ELECTRONICS (Master Device) A3LWEA453E ADLINK PXI/DFS Measurement System 11/25/2014 Annual 301081/711 Agilent N9020A / SIGNAL ANALYZER 06/30/2015 Annual MY51110085 Agilent N9020A / SIGNAL ANALYZER 07/02/2015 Annual MY50510304 Agilent N1911A/Power Meter 07/09/2015 Annual MY45100523 Agilent N1921A /POWER SENSOR 07/09/2015 Annual MY45241059 Hewlett Packard 11636B/Power Divider 10/28/2014 Annual 11377 Agilent 87300B/Directional Coupler 12/08/2014 Annual 3116A03621 Hewlett Packard 11667B / Power Splitter 06/11/2015 Annual 5001 DIGITAL EP-3010 /DC POWER SUPPLY 10/30/2014 Annual 3110117 Agilent 8493C / Attenuator(10 dB) 08/20/2015 Annual 76649 WEINSCHEL 2-3 / Attenuator(3 dB) 10/30/2014 Annual BR0617 F-01P-02-014 (Rev.00) FCC ID: ZNFH960 HCT Co.,Ltd.


Document Created: 2015-09-16 10:04:39
Document Modified: 2015-09-16 10:04:39
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC