Test Report

FCC ID: Z64-CC3200MODR1

Test Report

Download: PDF
FCCID_2414073

ONE WORLD OUR APPROVAL Test report 264561-1TRFWL Date of issue: September 25, 2014 Applicant: Texas Instruments Inc. Product: CC3200 LaunchPad Model: CC3200MODR1M2AMOB FCC ID: IC Registration number: Z64-CC3200MODR1 451I-CC3200MODR1 Specifications:  FCC 47 CFR Part 15 Subpart C, §15.247 Operation in the 902–928 MHz, 2400–2483.5 MHz, 5725–5850 MHz  RSS-210, Issue 8, December 2010, Annex 8 Frequency Hopping and Digital Modulation Systems Operating in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz Bands www.nemko.com Nemko Canada Inc., a testing laboratory, is SCC Accredited LAB accredited by the Standards Council of Canada. The tests included in this report are within the scope of this accreditation LAB Accrédité CCN FCC 15.247 and RSS-210 A8.docx; Date: May 2013 TM

Test location Company name: Nemko Canada Inc. Address: 303 River Road City: Ottawa Province: Ontario Postal code: K1V 1H2 Country: Canada Telephone: +1 613 737 9680 Facsimile: +1 613 737 9691 Toll free: +1 800 563 6336 Website: www.nemko.com Site number: FCC: 176392; IC: 2040A-4 (3 m semi anechoic chamber) Tested by: Kevin Rose, Wireless/EMC Specialist Reviewed by: Andrey Adelberg, Senior Wireless/EMC Specialist Date: September 25, 2014 Signature: Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contain in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: 264561-1TRFWL Page 2 of 33

Table of contents Table of contents .......................................................................................................................................................................................................... 3 Section 1. Report summary ................................................................................................................................................................................. 4 1.1 Applicant and manufacturer .................................................................................................................................................................................... 4 1.2 Test specifications .................................................................................................................................................................................................... 4 1.3 Test methods............................................................................................................................................................................................................ 4 1.4 Statement of compliance ......................................................................................................................................................................................... 4 1.5 Exclusions ................................................................................................................................................................................................................. 4 1.6 Test report revision history ...................................................................................................................................................................................... 4 Section 2. Summary of test results ....................................................................................................................................................................... 5 2.1 FCC Part 15 Subpart C, general requirements test results ........................................................................................................................................ 5 2.2 FCC Part 15 Subpart C, intentional radiators test results.......................................................................................................................................... 5 2.3 IC RSS-GEN, Issue 3, test results ............................................................................................................................................................................... 5 2.4 IC RSS-210, Issue 8, test results ................................................................................................................................................................................ 6 Section 3. Equipment under test (EUT) details ..................................................................................................................................................... 7 3.1 Sample information .................................................................................................................................................................................................. 7 3.2 EUT information ....................................................................................................................................................................................................... 7 3.3 Technical information .............................................................................................................................................................................................. 7 3.4 Product description and theory of operation ........................................................................................................................................................... 7 3.5 EUT exercise details .................................................................................................................................................................................................. 7 3.6 EUT setup diagram ................................................................................................................................................................................................... 8 Section 4. Engineering considerations .................................................................................................................................................................. 9 4.1 Modifications incorporated in the EUT..................................................................................................................................................................... 9 4.2 Technical judgment .................................................................................................................................................................................................. 9 4.3 Deviations from laboratory tests procedures ........................................................................................................................................................... 9 Section 5. Test conditions .................................................................................................................................................................................. 10 5.1 Atmospheric conditions ......................................................................................................................................................................................... 10 5.2 Power supply range ................................................................................................................................................................................................ 10 Section 6. Measurement uncertainty ................................................................................................................................................................. 11 6.1 Uncertainty of measurement ................................................................................................................................................................................. 11 Section 7. Test equipment ................................................................................................................................................................................. 12 7.1 Test equipment list ................................................................................................................................................................................................. 12 Section 8. Testing data ...................................................................................................................................................................................... 13 8.1 FCC 15.207(a) and RSS-Gen 7.2.4 AC power line conducted emissions limits ........................................................................................................ 13 8.2 FCC 15.247(a)(2) and RSS-210 A8.2(a) Minimum 6 dB bandwidth for systems using digital modulation techniques ............................................ 17 8.3 RSS-Gen 4.6.1 Occupied bandwidth ....................................................................................................................................................................... 19 8.4 FCC 15.247(b) and RSS-210 A8.4 (4) Transmitter output power and e.i.r.p. requirements .................................................................................... 21 8.5 FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions....................................................................................................................... 23 8.6 FCC 15.247(e) and RSS-210 A8.2(b) Power spectral density for digitally modulated devices ................................................................................. 31 Section 9. Block diagrams of test set-ups ........................................................................................................................................................... 33 9.1 Radiated emissions set-up...................................................................................................................................................................................... 33 9.2 Conducted emissions set-up .................................................................................................................................................................................. 33 Report reference ID: 264561-1TRFWL Page 3 of 33

Section 1 Report summary Section 1. Report summary 1.1 Applicant and manufacturer Company name Texas Instruments Inc. Address 12500 TI Boulevard City Dallas Province/State Texas Postal/Zip code 75243 Country USA 1.2 Test specifications FCC 47 CFR Part 15, Subpart C, Clause 15.247 Operation in the 902–928 MHz, 2400–2483.5 MHz, 5725–5850 MHz Frequency Hopping and Digital Modulation Systems Operating in the 902–928 MHz, 2400–2483.5 MHz, RSS-210, Issue 8 Annex 8 and 5725–5850 MHz Bands 1.3 Test methods Guidance for compliance measurements on DTS 558074 D01 Meas Guidance v03r02 (June 6, 2014) operating under 15.247 American National Standard for Methods of Measurement of Radio- Noise Emissions from Low-Voltage ANSI C64.3 v 2003 Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz 1.4 Statement of compliance In the configuration tested, the EUT was found compliant. Testing was completed against all relevant requirements of the test standard. Results obtained indicate that the product under test complies in full with the requirements tested. The test results relate only to the items tested. See “Summary of test results” for full details. 1.5 Exclusions None 1.6 Test report revision history Revision # Details of changes made to test report TRF Original report issued Report reference ID: 264561-1TRFWL Page 4 of 33

Section 2: Summary of test results Section 2. Summary of test results 2.1 FCC Part 15 Subpart C, general requirements test results Part Test description Verdict §15.207(a) Conducted limits Pass §15.31(e) Variation of power source Pass1 §15.203 Antenna requirement Pass2 Notes: 1 Measurements of the variation of the input power or the radiated signal level of the fundamental frequency component of the emission, as appropriate, was performed with the supply voltage varied between 85 % and 115 % of the nominal rated supply voltage. No noticeable output power variation was observed 2 The Antennas are located within the enclosure of EUT and not user accessible. 2.2 FCC Part 15 Subpart C, intentional radiators test results Part Test description Verdict §15.247(a)(1)(i) Frequency hopping systems operating in the 902–928 MHz band Not applicable §15.247(a)(1)(ii) Frequency hopping systems operating in the 5725–5850 MHz band Not applicable §15.247(a)(1)(iii) Frequency hopping systems operating in the 2400–2483.5 MHz band Not applicable §15.247(a)(2) Minimum 6 dB bandwidth for systems using digital modulation techniques Pass §15.247(b)(1) Maximum peak output power of frequency hopping systems operating in the 2400–2483.5 MHz band and Not applicable 5725–5850 MHz band §15.247(b)(2) Maximum peak output power of Frequency hopping systems operating in the 902–928 MHz band Not applicable §15.247(b)(3) Maximum peak output power of systems using digital modulation in the 902–928 MHz, 2400–2483.5 Pass MHz, and 5725–5850 MHz bands §15.247(c)(1) Fixed point-to-point operation with directional antenna gains greater than 6 dBi Not applicable §15.247(c)(2) Transmitters operating in the 2400–2483.5 MHz band that emit multiple directional beams Not applicable §15.247(d) Spurious emissions Pass §15.247(e) Power spectral density for digitally modulated devices Pass §15.247(f) Time of occupancy for hybrid systems Not applicable 2.3 IC RSS-GEN, Issue 3, test results Part Test description Verdict 4.6.1 Occupied bandwidth Pass 6.1 Receiver spurious emissions limits (radiated) Not applicable 6.2 Receiver spurious emissions limits (antenna conducted) Not applicable1 7.2.4 AC power lines conducted emission limits Pass Notes: 1 According to Notice 2012-DRS0126 (from January 2012) section 2.2 of RSS-Gen, Issue 3 has been revised. The EUT does not have a stand-alone receiver neither scanner receiver, therefore exempt from receiver requirements. Report reference ID: 264561-1TRFWL Page 5 of 33

Section 2: Summary of test results 2.4 IC RSS-210, Issue 8, test results Part Test description Verdict A8.1 Frequency hopping systems A8.1 (a) Bandwidth of a frequency hopping channel Not applicable A8.1 (b) Minimum channel spacing for frequency hopping systems Not applicable A8.1 (c) Frequency hopping systems operating in the 902–928 MHz band Not applicable A8.1 (d) Frequency hopping systems operating in the 2400–2483.5 MHz band Not applicable A8.1 (e) Frequency hopping systems operating in the 5725–5850 MHz band Not applicable A8.2 Digital modulation systems A8.2 (a) Minimum 6 dB bandwidth Pass A8.2 (b) Maximum power spectral density Pass A8.3 Hybrid systems A8.3 (1) Digital modulation turned off Not applicable A8.3 (2) Frequency hopping turned off Not applicable A8.4 Transmitter output power and e.i.r.p. requirements A8.4 (1) For frequency hopping systems operating in the 902–928 MHz band Not applicable A8.4 (2) For frequency hopping systems operating in the 2400–2483.5 MHz band Not applicable A8.4 (3) For frequency hopping systems operating in the 5725–5850 MHz Not applicable A8.4 (4) For systems employing digital modulation techniques Pass A8.4 (5) For point-to-point systems in 2400–2483.5 MHz and 5725–5850 MHz band Not applicable A8.4 (6) For transmitters which operate in the 2400–2483.5 MHz band with multiple directional beams Not applicable A8.5 Out-of-band emissions Pass Notes: None Report reference ID: 264561-1TRFWL Page 6 of 33

Section 3: Equipment under test (EUT) details Section 3. Equipment under test (EUT) details 3.1 Sample information Receipt date July 21, 2014 Nemko sample ID number 5 3.2 EUT information Product name CC3200 LaunchPad Model CC3200MODR1M2AMOB Serial number QLA0033 and QLA0031 3.3 Technical information Operating band 2400–2483.5 MHz Operating frequency 2412–2462 MHz Modulation type 802.11b/g/n Occupied bandwidth (99 %) 14.03 MHz (802.11b), 16.34 MHz (802.11g), 17.59 MHz (802.11n) Emission designator W7D Power requirements 120 VAC, 60 Hz via Laptop power adapter connected with USB cord to EUT Taiyo Yuden 2.4 GHz Multilayer RadiEdge Antenna, MN: AH 316M245001, Peak Gain: 1.9 dBi Antenna information The EUT uses a unique antenna coupling/ non-detachable antenna to the intentional radiator. 3.4 Product description and theory of operation The EUT is designed to be used as a standalone development platform for application development using the CC3200 device. It can be also used in conjunction with compatible booster-packs to enhance the peripherals available in the system. The board features on-board emulation using FTDI device and has an array of sensors for an out of the box experience. This board can be directly connected to the PC using software development platforms including CCS and IAR. 3.5 EUT exercise details There were 2 samples provided for testing: one with the permanent antenna and the second one is with the 50 Ω antenna cable for conducted measurements. EUT was controlled from laptop using Radio Tool 0.5 CLI application. Report reference ID: 264561-1TRFWL Page 7 of 33

Section 3: Equipment under test (EUT) details 3.6 EUT setup diagram Figure 3.6-1: Setup diagram Report reference ID: 264561-1TRFWL Page 8 of 33

Section 4: Engineering consideration Section 4. Engineering considerations 4.1 Modifications incorporated in the EUT There were no modifications performed to the EUT during this assessment. 4.2 Technical judgment None 4.3 Deviations from laboratory tests procedures No deviations were made from laboratory procedures. Report reference ID: 264561-1TRFWL Page 9 of 33

Section 5: Test conditions Section 5. Test conditions 5.1 Atmospheric conditions Temperature 15–30 °C Relative humidity 20–75 % Air pressure 860–1060 mbar When it is impracticable to carry out tests under these conditions, a note to this effect stating the ambient temperature and relative humidity during the tests shall be recorded and stated. 5.2 Power supply range The normal test voltage for equipment to be connected to the mains shall be the nominal mains voltage. For the purpose of the present document, the nominal voltage shall be the declared voltage, or any of the declared voltages ±5 %, for which the equipment was designed. Report reference ID: 264561-1TRFWL Page 10 of 33

Section 6: Measurement uncertainty Section 6. Measurement uncertainty 6.1 Uncertainty of measurement Nemko Canada Inc. has calculated measurement uncertainty and is documented in EMC/MUC/001 “Uncertainty in EMC measurements.” Measurement uncertainty was calculated using the methods described in CISPR 16-4 Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC measurements; as well as described in UKAS LAB34: The expression of Uncertainty in EMC Testing. Measurement uncertainty calculations assume a coverage factor of K=2 with 95% certainty. Report reference ID: 264561-1TRFWL Page 11 of 33

Section 7: Test equipment Section 7. Test equipment 7.1 Test equipment list Table 7.1-1: Equipment list Equipment Manufacturer Model no. Asset no. Cal cycle Next cal. 3 m EMI test chamber TDK SAC-3 FA002047 1 year Mar. 18/15 Flush mount turntable Sunol FM2022 FA002082 — NCR Controller Sunol SC104V FA002060 — NCR Antenna mast Sunol TLT2 FA002061 — NCR Horn antenna (1–18 GHz) EMCO 3115 FA000825 1 year Mar. 10/15 Pre-amplifier (1–18 GHz) JCA JCA118-503 FA002091 1 year June 23/15 Bilog antenna (20–3000 MHz) Sunol JB3 FA002108 1 year Mar. 12/15 50 Ω coax cable C.C.A. None FA002555 1 year June 23/15 50 Ω coax cable Huber + Suhner NONE FA002074 1 year June 23/15 Horn antenna 18–40 GHz EMCO 3116 FA001847 2 year Sept. 06/14 18–26 GHz pre-amplifier Narda BBS-1826N612 FA001550 — VOU Note: NCR - no calibration required, VOU - verify on use Report reference ID: 264561-1TRFWL Page 12 of 33

Section 8 Testing data Test name FCC 15.207(a) and RSS-Gen 7.2.4 AC power line conducted emissions limits Specification FCC Part 15 Subpart C and RSS-Gen, Issue 3 Section 8. Testing data 8.1 FCC 15.207(a) and RSS-Gen 7.2.4 AC power line conducted emissions limits 8.1.1 Definitions and limits FCC: Except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table, as measured using a 50 μH/50 Ω line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. IC: The purpose of this test is to measure unwanted radio frequency currents induced in any AC conductor external to the equipment which could conduct interference to other equipment via the AC electrical network. Except when the requirements applicable to a given device state otherwise, for any licence-exempt radiocommunication device equipped to operate from the public utility AC power supply, either directly or indirectly, the radio frequency voltage that is conducted back onto the AC power lines in the frequency range of 0.15 MHz to 30 MHz shall not exceed the limits shown in Table 2. The tighter limit applies at the frequency range boundaries. The conducted emissions shall be measured with a 50 Ω/50 µH line impedance stabilization network (LISN). Table 8.1-1: Conducted emissions limit Frequency of emission, Conducted limit, dBµV MHz Quasi-peak Average 0.15–0.5 66 to 56* 56 to 46* 0.5–5 56 46 5–30 60 50 Note: * - Decreases with the logarithm of the frequency. 8.1.2 Test summary Test date July 24, 2014 Temperature 23 °C Test engineer Kevin Rose Air pressure 1003 mbar Verdict Pass Relative humidity 36 % Report reference ID: 264561-1TRFWL Page 13 of 33

Section 8 Testing data Test name FCC 15.207(a) and RSS-Gen 7.2.4 AC power line conducted emissions limits Specification FCC Part 15 Subpart C and RSS-Gen, Issue 3 8.1.3 Observations, settings and special notes The EUT was set up as tabletop configuration. The spectral scan has been corrected with transducer factors (i.e. cable loss, LISN factors, and attenuators) for determination of compliance. A preview measurement was generated with the receiver in continuous scan mode. Emissions detected within 6 dB or above limit were re-measured with the appropriate detector against the correlating limit and recorded as the final measurement. Receiver settings for preview measurements: Resolution bandwidth 9 kHz Video bandwidth 30 kHz Detector mode Peak and Average Trace mode Max Hold Measurement time 1000 ms Receiver settings for final measurements: Resolution bandwidth 9 kHz Video bandwidth 30 kHz Detector mode Quasi-Peak and Average Trace mode Max Hold Measurement time 1000 ms Report reference ID: 264561-1TRFWL Page 14 of 33

Section 8 Testing data Test name FCC 15.207(a) and RSS-Gen 7.2.4 AC power line conducted emissions limits Specification FCC Part 15 Subpart C and RSS-Gen, Issue 3 8.1.4 Test data 70 65 60 55 50 45 Level in dBµV 40 35 30 25 20 15 10 5 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz N EX -264561 CE E m issio n s 120 V ac 60 Hz Phase CISPR 22 M ain s Q P Class B CISPR 22 M ain s A V Class B Pre view Re sult 1-PK+ Pre view Re sult 2-A VG Plot 8.1-1: Conducted emissions on phase line Report reference ID: 264561-1TRFWL Page 15 of 33

Section 8 Testing data Test name FCC 15.207(a) and RSS-Gen 7.2.4 AC power line conducted emissions limits Specification FCC Part 15 Subpart C and RSS-Gen, Issue 3 8.1.4 Test data, continued 70 65 60 55 50 45 Level in dBµV 40 35 30 25 20 15 10 5 0 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz N EX -264561 CE E m issio n s 120 V ac 60 Hz N eu tral CISPR 22 M ain s Q P Class B CISPR 22 M ain s A V Class B Pre view Re sult 1-PK+ Pre view Re sult 2-A VG Plot 8.1-2: Conducted emissions on neutral line Report reference ID: 264561-1TRFWL Page 16 of 33

Section 8 Testing data FCC 15.247(a)(2) and RSS-210 A8.2(a) Minimum 6 dB bandwidth for systems using digital Test name modulation techniques Specification FCC 15 Subpart C and RSS-210, Issue 8 8.2 FCC 15.247(a)(2) and RSS-210 A8.2(a) Minimum 6 dB bandwidth for systems using digital modulation techniques 8.2.1 Definitions and limits FCC and IC: (a) Operation under the provisions of this Section is limited to frequency hopping and digitally modulated intentional radiators that comply with the following provisions: (2) Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 8.2.2 Test summary Test date July 28, 2014 Temperature 21 °C Test engineer Kevin Rose Air pressure 1003 mbar Verdict Pass Relative humidity 38 % 8.2.3 Observations, settings and special notes Spectrum analyser settings: Resolution bandwidth 1–5 % of DTS BW (no wider than 100 kHz) Video bandwidth ≥3 × RBW Frequency span 30 MHz Detector mode Peak Trace mode Max Hold 8.2.4 Test data Table 8.2-1: 6 dB bandwidth results Modulation Frequency, MHz 6 dB bandwidth, MHz Minimum limit, MHz Margin, MHz 2412 10.04 0.5 9.54 802.11b 2437 9.99 0.5 9.49 2462 10.04 0.5 9.54 2412 15.19 0.5 14.69 802.11g 2437 15.09 0.5 14.59 2462 15.19 0.5 14.69 2412 15.19 0.5 14.69 802.11n 2437 15.19 0.5 14.69 2462 15.08 0.5 14.58 Report reference ID: 264561-1TRFWL Page 17 of 33

Section 8 Testing data FCC 15.247(a)(2) and RSS-210 A8.2(a) Minimum 6 dB bandwidth for systems using digital Test name modulation techniques Specification FCC 15 Subpart C and RSS-210, Issue 8 8.2.4 Test data, continued * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -4.50 dBm VBW 300 kHz -0.91 dBm Ref 11.4 dBm Att 25 dB SWT 15 ms 2.406951923 GHz Ref 11.4 dBm Att 25 dB SWT 15 ms 2.444548077 GHz 10 Offset 11.4 dB Delta 1 [T1 ] 10 Offset 11.4 dB Delta 1 [T1 ] 0.39 dB -1.14 dB 10.048076923 MHz A 1 -15.096153846 MHz A 1 0 1 0 1 1 PK 1 PK VIEW VIEW -10 LVL -10 LVL -20 -20 -30 -30 -40 -40 3DB 3DB -50 -50 -60 -60 -70 -70 -80 -80 Center 2.412 GHz 3 MHz/ Span 30 MHz Center 2.437 GHz 3 MHz/ Span 30 MHz Date: 28.JUL.2014 13:46:36 Date: 28.JUL.2014 13:51:19 Figure 8.2-1: 6 dB bandwidth on 802.11b, sample plot Figure 8.2-2: 6 dB bandwidth on 802.11g, sample plot * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -4.64 dBm Ref 11.4 dBm Att 25 dB SWT 15 ms 2.469548077 GHz 10 Offset 11.4 dB Delta 1 [T1 ] 0.60 dB -15.086538462 MHz A 0 1 1 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.462 GHz 3 MHz/ Span 30 MHz Date: 28.JUL.2014 14:02:06 Figure 8.2-3: 6 dB bandwidth on 802.11n, sample plot Report reference ID: 264561-1TRFWL Page 18 of 33

Section 8 Testing data Test name RSS-Gen 4.6.1 Occupied bandwidth Specification RSS-Gen, Issue 3 8.3 RSS-Gen 4.6.1 Occupied bandwidth 8.3.1 Definitions and limits When an occupied bandwidth value is not specified in the applicable RSS, the transmitted signal bandwidth to be reported is to be its 99 percent emission bandwidth, as calculated or measured. The transmitter shall be operated at its maximum carrier power measured under normal test conditions. The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. 8.3.2 Test summary Test date July 28, 2014 Temperature 21 °C Test engineer Kevin Rose Air pressure 1003 mbar Verdict Pass Relative humidity 38 % 8.3.3 Observations, settings and special notes Spectrum analyser settings: Resolution bandwidth 100 kHz Video bandwidth ≥3 × RBW Frequency span 30 MHz Detector mode Peak Trace mode Max Hold 8.3.4 Test data Table 8.3-1: 99 % bandwidth results Modulation Frequency, MHz 99 % occupied bandwidth, MHz 2412 14.03 802.11b 2437 13.99 2462 13.99 2412 16.29 802.11g 2437 16.34 2462 16.29 2412 17.50 802.11n 2437 17.59 2462 17.50 Report reference ID: 264561-1TRFWL Page 19 of 33

Section 8 Testing data Test name RSS-Gen 4.6.1 Occupied bandwidth Specification RSS-Gen, Issue 3 8.3.4 Test data, continued * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -43.14 dBm VBW 300 kHz -27.57 dBm Ref 11.4 dBm Att 5 dB SWT 15 ms 2.427000000 GHz Ref 11.4 dBm Att 5 dB SWT 15 ms 2.452000000 GHz 10 Offset 11.4 dB OBW 14.038461538 MHz 10 Offset 11.4 dB OBW 16.346153846 MHz Temp 1 [T1 OBW] Temp 1 [T1 OBW] -11.94 dBm A -5.91 dBm A 0 0 2.404980769 GHz 2.428826923 GHz T1 T2 1 PK Temp 2 [T1 OBW] 1 PK Temp 2 [T1 OBW] MAXH MAXH T1 T2 -11.77 dBm -6.15 dBm -10 LVL -10 LVL 2.419019231 GHz 2.445173077 GHz -20 -20 1 -30 -30 -40 1 -40 3DB 3DB -50 -50 -60 -60 -70 -70 -80 -80 Center 2.412 GHz 3 MHz/ Span 30 MHz Center 2.437 GHz 3 MHz/ Span 30 MHz Date: 28.JUL.2014 14:15:45 Date: 28.JUL.2014 14:13:43 Figure 8.3-1: 99 % bandwidth on 802.11b, sample plot Figure 8.3-2: 99 % bandwidth on 802.11g, sample plot * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -0.44 dBm Ref 11.4 dBm Att 5 dB SWT 15 ms 2.459451923 GHz 10 Offset 11.4 dB OBW 17.500000000 MHz Temp 1 [T1 OBW] 1 -9.25 dBm A 0 2.453250000 GHz 1 PK TempT2 2 [T1 OBW] T1 MAXH -9.01 dBm -10 LVL 2.470750000 GHz -20 -30 -40 3DB -50 -60 -70 -80 Center 2.462 GHz 3 MHz/ Span 30 MHz Date: 28.JUL.2014 14:11:50 Figure 8.3-3: 99 % bandwidth on 802.11n, sample plot Report reference ID: 264561-1TRFWL Page 20 of 33

Section 8 Testing data Test name FCC 15.247(b) and RSS-210 A8.4 (4) Transmitter output power and e.i.r.p. requirements Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.4 FCC 15.247(b) and RSS-210 A8.4 (4) Transmitter output power and e.i.r.p. requirements 8.4.1 Definitions and limits FCC: (b) The maximum peak conducted output power of the intentional radiator shall not exceed the following: (3) For systems using digital modulation in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands: 1 W (30 dBm). As an alternative to a peak power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted Output Power is defined as the total transmit power delivered to all antennas and antenna elements averaged across all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or is transmitting at a reduced power level. If multiple modes of operation are possible (e.g., alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any mode. (4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. (i) Systems operating in the 2400–2483.5 MHz band that are used exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain greater than 6 dBi provided the maximum peak output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. Fixed, point-to-point operation, as used in paragraphs (b)(3)(i) and (b)(3)(ii) of this section, excludes the use of point-to-multipoint systems, omnidirectional applications, and multiple co-located intentional radiators transmitting the same information. The operator of the spread spectrum intentional radiator or, if the equipment is professionally installed, the installer is responsible for ensuring that the system is used exclusively for fixed, point-to-point operations. The instruction manual furnished with the intentional radiator shall contain language in the installation instructions informing the operator and the installer of this responsibility. (c) Operation with directional antenna gains greater than 6 dBi. (2) In addition to the provisions in paragraphs (b)(1), (b)(3), (b)(4) and (c)(1)(i) of this section, transmitters operating in the 2400–2483.5 MHz band that emit multiple directional beams, simultaneously or sequentially, for the purpose of directing signals to individual receivers or to groups of receivers provided the emissions comply with the following: (i) Different information must be transmitted to each receiver. (ii) If the transmitter employs an antenna system that emits multiple directional beams but does not do emit multiple directional beams simultaneously, the total output power conducted to the array or arrays that comprise the device, i.e., the sum of the power supplied to all antennas, antenna elements, staves, etc. and summed across all carriers or frequency channels, shall not exceed the limit specified in paragraph (b)(1) or (b)(3) of this section, as applicable. However, the total conducted output power shall be reduced by 1 dB below the specified limits for each 3 dB that the directional gain of the antenna/antenna array exceeds 6 dBi. The directional antenna gain shall be computed as follows: (A) The directional gain shall be calculated as the sum of 10 log (number of array elements or staves) plus the directional gain of the element or stave having the highest gain. IC: A8.4 (4) Transmitter Output Power and e.i.r.p. Requirements for systems employing digital modulation techniques operating in the bands 902–928 MHz, 2400–2483.5 MHz and 5725–5850 MHz bands For systems employing digital modulation techniques operating in the bands 902–928 MHz, 2400–2483.5 MHz and 5725–5850 MHz, the maximum peak conducted output power shall not exceed 1 W. Except as provided in Section A8.4(5), the e.i.r.p. shall not exceed 4 W. As an alternative to a peak power measurement, compliance can be based on a measurement of the maximum conducted output power (see RSS-Gen). 8.4.2 Test summary Test date July 28, 2014 Temperature 21 °C Test engineer Kevin Rose Air pressure 1003 mbar Verdict Pass Relative humidity 38 % Report reference ID: 264561-1TRFWL Page 21 of 33

Section 8 Testing data Test name FCC 15.247(b) and RSS-210 A8.4 (4) Transmitter output power and e.i.r.p. requirements Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.4.3 Observations, settings and special notes The test was performed according to DTS guidelines section 9.2.2.2 Method AVGSA-1 (trace averaging with the EUT transmitting at full power throughout each sweep). Spectrum analyser settings: Resolution bandwidth 1 MHz Video bandwidth ≥3 × RBW Frequency span 50 MHz Detector mode RMS Trace mode Power averaging over 100 sweeps Power integration Power over 20 MHz 8.4.4 Test data Table 8.4-1: Output power measurements results Frequency, Conducted output power, dBm Antenna EIRP, EIRP limit, EIRP margin, Modulation Margin, dB MHz Measured Limit gain, dBi dBm dBm dB 2412 12.18 30 17.82 1.9 14.08 36 21.92 802.11b 2437 14.14 30 15.86 1.9 16.04 36 19.96 2462 12.24 30 17.76 1.9 14.14 36 21.86 2412 12.75 30 17.25 1.9 14.65 36 21.35 802.11g 2437 14.64 30 15.36 1.9 16.54 36 19.46 2462 12.98 30 17.02 1.9 14.88 36 21.12 2412 11.43 30 18.57 1.9 13.33 36 22.67 802.11n 2437 14.20 30 15.80 1.9 16.10 36 19.9 2462 11.58 30 18.42 1.9 13.48 36 22.52 * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] VBW 10 MHz -48.44 dBm VBW 10 MHz -45.61 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.437000000 GHz Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.387000000 GHz Offset 11.4 dB Offset 11.4 dB 10 10 0 A 0 A -10 -10 1 RM * GAT 1 RM * GAT MAXH -20 TRG MAXH -20 TRG LVL LVL -30 -30 SWP 100 of 100 SWP 100 of 100 1 -40 1 -40 -50 -50 -60 -60 -70 3DB -70 3DB Center 2.462 GHz 5 MHz/ Span 50 MHz Center 2.412 GHz 5 MHz/ Span 50 MHz Tx Channel Tx Channel Bandwidth 20 MHz Power 12.24 dBm Bandwidth 20 MHz Power 12.75 dBm Figure 8.4-1: Output power on 802.11b, sample plot Figure 8.4-2: Output power on 802.11g, sample plot * RBW 1 MHz Marker 1 [T1 ] VBW 10 MHz 2.66 dBm Ref 20 dBm * Att 20 dB SWT 2.5 ms 2.437000000 GHz Offset 11.4 dB 10 1 0 A -10 1 RM * GAT VIEW -20 TRG LVL -30 SWP 100 of 100 -40 -50 Date: 28.JUL.2014 15:22:10 Date: 28.JUL.2014 15:27:06 -60 -70 3DB Center 2.437 GHz 5 MHz/ Span 50 MHz Tx Channel Bandwidth 20 MHz Power 14.20 dBm Figure 8.4-3: Output power on 802.11n, sample plot Report reference ID: 264561-1TRFWL Page 22 of 33 Date: 28.JUL.2014 15:35:19

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5 FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions 8.5.1 Definitions and limits FCC: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). IC: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the radio frequency power that is produced shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under Section A8.4(4), the attenuation required shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in Tables 2 and 3 is not required. Table 8.5-1: FCC §15.209 and RSS-Gen – Radiated emission limits Frequency, Field strength of emissions Measurement distance, m MHz µV/m dBµV/m 0.009–0.490 2400/F 67.6 – 20 × log10(F) 300 0.490–1.705 24000/F 87.6 – 20 × log10(F) 30 1.705–30.0 30 29.5 30 30–88 100 40.0 3 88–216 150 43.5 3 216–960 200 46.0 3 above 960 500 54.0 3 Notes: In the emission table above, the tighter limit applies at the band edges. For frequencies above 1 GHz the limit on peak RF emissions is 20 dB above the maximum permitted average emission limit applicable to the equipment under test Table 8.5-2: IC restricted frequency bands MHz MHz MHz GHz 0.090–0.110 12.51975–12.52025 399.9–410 5.35–5.46 2.1735–2.1905 12.57675–12.57725 608–614 7.25–7.75 3.020–3.026 13.36–13.41 960–1427 8.025–8.5 4.125–4.128 16.42–16.423 1435–1626.5 9.0–9.2 4.17725–4.17775 16.69475–16.69525 1645.5–1646.5 9.3–9.5 4.20725–4.20775 16.80425–16.80475 1660–1710 10.6–12.7 5.677-5.683 25.5–25.67 1718.8–1722.2 13.25–13.4 6.215–6.218 37.5–38.25 2200–2300 14.47–14.5 6.26775–6.26825 73–74.6 2310–2390 15.35–16.2 6.31175–6.31225 74.8–75.2 2655–2900 17.7–21.4 8.291–8.294 108–138 3260–3267 22.01–23.12 8.362–8.366 156.52475–156.52525 3332–3339 23.6–24.0 8.37625–8.38675 156.7–156.9 3345.8–3358 31.2–31.8 8.41425–8.41475 240–285 3500–4400 36.43–36.5 12.29–12.293 322–335.4 4500–5150 Above 38.6 Note: Certain frequency bands listed in Table 8.5-2 and above 38.6 GHz are designated for low-power licence-exempt applications. These frequency bands and the requirements that apply to the devices are set out in this Standard Report reference ID: 264561-1TRFWL Page 23 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.1 Definitions and limits, continued Table 8.5-3: FCC restricted frequency bands MHz MHz MHz GHz 0.090–0.110 16.42–16.423 399.9–410 4.5–5.15 0.495–0.505 16.69475–16.69525 608–614 5.35–5.46 2.1735–2.1905 16.80425–16.80475 960–1240 7.25–7.75 4.125–4.128 25.5–25.67 1300–1427 8.025–8.5 4.17725–4.17775 37.5–38.25 1435–1626.5 9.0–9.2 4.20725–4.20775 73–74.6 1645.5–1646.5 9.3–9.5 6.215–6.218 74.8–75.2 1660–1710 10.6–12.7 6.26775–6.26825 108–121.94 1718.8–1722.2 13.25–13.4 6.31175–6.31225 123–138 2200–2300 14.47–14.5 8.291–8.294 149.9–150.05 2310–2390 15.35–16.2 8.362–8.366 156.52475–156.52525 2483.5–2500 17.7–21.4 8.37625–8.38675 156.7–156.9 2690–2900 22.01–23.12 8.41425–8.41475 162.0125–167.17 3260–3267 23.6–24.0 12.29–12.293 167.72–173.2 3332–3339 31.2–31.8 12.51975–12.52025 240–285 3345.8–3358 36.43–36.5 12.57675–12.57725 322–335.4 3600–4400 Above 38.6 13.36–13.41 8.5.2 Test summary Test date July 28, 2014 Temperature 21 °C Test engineer Kevin Rose Air pressure 1003 mbar Verdict Pass Relative humidity 38 % 8.5.3 Observations, settings and special notes The spectrum was searched from 30 MHz to the 10th harmonic. Cabinet radiation measurements were performed at a distance of 3 m; No emissions higher than 10 dB below the limit were detected. Since fundamental power was tested using average method, the spurious emissions outside restricted bands limit is −30 dBc/100 kHz Spectrum analyser settings for radiated measurements within restricted bands below 1 GHz: Resolution bandwidth 100 kHz Video bandwidth 300 kHz Detector mode Peak Trace mode Max Hold Spectrum analyser settings for peak radiated measurements within restricted bands above 1 GHz: Resolution bandwidth 1 MHz Video bandwidth 3 MHz Detector mode Peak Trace mode Max Hold Spectrum analyser settings for average radiated measurements within restricted bands above 1 GHz: Resolution bandwidth 1 MHz Video bandwidth 10 Hz Detector mode Peak Trace mode Max Hold Report reference ID: 264561-1TRFWL Page 24 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.3 Observations, settings and special notes, continued Spectrum analyser settings for conducted spurious emissions measurements outside restricted bands: Resolution bandwidth 100 kHz Video bandwidth 300 kHz Detector mode Peak Trace mode Max Hold Spectrum analyser settings for conducted spurious emissions measurements within restricted bands below 1 GHz: Resolution bandwidth 100 kHz Video bandwidth 300 kHz Detector mode Peak Trace mode Max Hold Note: as per 12.2.3 Quasi-Peak measurement procedure of the 558074 D01 DTS Meas Guidance v03r02: As an alternative to CISPR quasi-peak measurement, compliance was demonstrated to the applicable emission limits using a peak detector. Spectrum analyser settings for conducted spurious emissions peak measurements within restricted bands above 1 GHz: Resolution bandwidth 1 MHz Video bandwidth 3 MHz Detector mode Peak Trace mode Max Hold Spectrum analyser settings for conducted spurious emissions average measurements within restricted bands above 1 GHz: Resolution bandwidth 1 MHz Video bandwidth 3 MHz Detector mode RMS Trace mode Power average over 100 sweeps Report reference ID: 264561-1TRFWL Page 25 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.4 Test data * RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ] VBW 300 kHz -50.35 dBm VBW 300 kHz -45.67 dBm Ref 20 dBm * Att 20 dB SWT 2.5 s 70.016025641 MHz Ref 20 dBm * Att 20 dB SWT 2.5 s 110.032051282 MHz 20 Offset 11.4 dB Marker 1 [T1 ] 20 Offset 11.4 dB Marker 1 [T1 ] 0.57 dBm 3.60 dBm 2.390945513 GHz A 2.430961538 GHz A 10 10 1 1 PK 1 1 PK VIEW VIEW 0 0 LVL LVL -10 -10 -20 -20 -30 -30 3DB 3DB -40 -40 2 2 -50 -50 -60 -60 -70 -70 -80 -80 Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Date: 28.JUL.2014 15:03:19 Date: 28.JUL.2014 15:04:06 Figure 8.5-1: Conducted spurious 802.11b, low channel Figure 8.5-2: Conducted spurious 802.11b, mid channel * RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Delta 1 [T1 ] VBW 300 kHz -48.87 dBm VBW 300 kHz -44.15 dB Ref 20 dBm * Att 20 dB SWT 2.5 s 110.032051282 MHz Ref 11.4 dBm * Att 10 dB SWT 10 ms -15.032051282 MHz 20 Offset 11.4 dB Marker 1 [T1 ] 10 Offset 11.4 dB Marker 1 [T1 ] 1.28 dBm 1.40 dBm 1 2.430961538 GHz A 2.412500000 GHz A 10 0 1 PK 1 1 PK MAXH VIEW 0 LVL -10 LVL -10 -20 -20 -30 -30 1 -40 3DB 3DB -40 -50 2 -50 -60 -60 -70 -70 -80 -80 Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Center 2.4 GHz 10 MHz/ Span 100 MHz Date: 28.JUL.2014 15:04:39 Date: 28.JUL.2014 14:53:49 Figure 8.5-3: Conducted spurious 802.11b, high channel Figure 8.5-4: Conducted spurious 802.11b, Lower band edge Report reference ID: 264561-1TRFWL Page 26 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.5 Test data, continued * RBW 100 kHz Delta 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ] VBW 300 kHz -53.77 dB VBW 300 kHz -52.08 dBm Ref 20 dBm * Att 20 dB SWT 10 ms 23.717948718 MHz Ref 20 dBm * Att 20 dB SWT 2.5 s 2.791105769 GHz 20 Offset 11.4 dB Marker 1 [T1 ] 20 Offset 11.4 dB Marker 1 [T1 ] 2.35 dBm -0.08 dBm 2.461384615 GHz A 2.390945513 GHz A 10 10 1 1 PK 1 PK 1 MAXH MAXH 0 0 LVL LVL -10 -10 -20 -20 -30 -30 3DB 3DB -40 -40 2 2 -50 -50 -60 -60 -70 -70 -80 -80 Center 2.4835 GHz 10 MHz/ Span 100 MHz Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Date: 28.JUL.2014 15:11:44 Date: 28.JUL.2014 15:07:09 Figure 8.5-5: Conducted spurious 802.11b, upper band edge Figure 8.5-6: Conducted spurious 802.11g, low channel * RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ] VBW 300 kHz -31.42 dBm VBW 300 kHz -50.32 dBm Ref 20 dBm * Att 20 dB SWT 2.5 s 2.390945513 GHz Ref 20 dBm * Att 20 dB SWT 2.5 s 3.271298077 GHz 20 Offset 11.4 dB Marker 1 [T1 ] 20 Offset 11.4 dB Marker 1 [T1 ] 0.50 dBm -1.22 dBm 2.430961538 GHz A 2.470977564 GHz A 10 10 1 PK 1 1 PK VIEW MAXH 1 0 0 LVL LVL -10 -10 -20 -20 2 -30 -30 3DB 3DB -40 -40 2 -50 -50 -60 -60 -70 -70 -80 -80 Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Date: 28.JUL.2014 15:06:36 Date: 28.JUL.2014 15:09:35 Figure 8.5-7: Conducted spurious 802.11g, mid channel Figure 8.5-8: Conducted spurious 802.11g, high channel Report reference ID: 264561-1TRFWL Page 27 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.6 Test data, continued * RBW 100 kHz Delta 1 [T1 ] * RBW 100 kHz Delta 2 [T1 ] VBW 300 kHz -32.69 dB VBW 300 kHz -47.41 dB Ref 11.4 dBm * Att 10 dB SWT 10 ms -13.525641026 MHz Ref 20 dBm * Att 20 dB SWT 10 ms 24.038461538 MHz 10 Offset 11.4 dB Marker 1 [T1 ] 20 Offset 11.4 dB Marker 1 [T1 ] 1 1.76 dBm 0.89 dBm 2.413301282 GHz A 2.460743590 GHz A 10 0 1 PK 1 PK 1 VIEW VIEW 0 -10 LVL LVL -10 -20 1 -20 -30 -30 -40 3DB 3DB -40 -50 2 -50 -60 -60 -70 -70 -80 -80 Center 2.4 GHz 10 MHz/ Span 100 MHz Center 2.4835 GHz 10 MHz/ Span 100 MHz Date: 28.JUL.2014 14:53:16 Date: 28.JUL.2014 15:11:07 Figure 8.5-9: Conducted spurious 802.11g, lower band edge Figure 8.5-10: Conducted spurious 802.11g, upper band edge * RBW 100 kHz Delta 2 [T1 ] * RBW 100 kHz Marker 2 [T1 ] VBW 300 kHz -53.10 dB VBW 300 kHz -54.20 dBm Ref 20 dBm * Att 20 dB SWT 2.5 s 800.320512821 MHz Ref 20 dBm * Att 20 dB SWT 2.5 s 4.071618590 GHz 20 Offset 11.4 dB Marker 1 [T1 ] 20 Offset 11.4 dB Marker 1 [T1 ] 0.06 dBm 2.41 dBm 2.390945513 GHz A 2.430961538 GHz A 10 10 1 1 PK 1 PK 1 VIEW MAXH 0 0 LVL LVL -10 -10 -20 -20 -30 -30 3DB 3DB -40 -40 -50 2 -50 2 -60 -60 -70 -70 -80 -80 Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Date: 28.JUL.2014 15:08:06 Date: 28.JUL.2014 15:08:47 Figure 8.5-11: Conducted spurious 802.11n, low channel Figure 8.5-12: Conducted spurious 802.11n, mid channel Report reference ID: 264561-1TRFWL Page 28 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.4 Test data, continued * RBW 100 kHz Marker 2 [T1 ] * RBW 100 kHz Delta 1 [T1 ] VBW 300 kHz -50.32 dBm VBW 300 kHz -34.82 dB Ref 20 dBm * Att 20 dB SWT 2.5 s 3.271298077 GHz Ref 11.4 dBm * Att 10 dB SWT 10 ms -14.903846154 MHz 20 Offset 11.4 dB Marker 1 [T1 ] 10 Offset 11.4 dB Marker 1 [T1 ] -1.22 dBm -0.15 dBm 2.470977564 GHz A 1 2.414423077 GHz A 10 0 1 PK 1 PK MAXH 1 VIEW 0 LVL -10 LVL -10 -20 -20 -30 1 -30 -40 3DB 3DB -40 -50 2 -50 -60 -60 -70 -70 -80 -80 Center 12.515 GHz 2.497 GHz/ Span 24.97 GHz Center 2.4 GHz 10 MHz/ Span 100 MHz Date: 28.JUL.2014 15:09:35 Date: 28.JUL.2014 14:50:42 Figure 8.5-13: Conducted spurious 802.11n, high channel Figure 8.5-14: Conducted spurious 802.11n, lower band edge * RBW 100 kHz Delta 2 [T1 ] VBW 300 kHz -46.19 dB Ref 20 dBm * Att 20 dB SWT 10 ms 20.320512821 MHz 20 Offset 11.4 dB Marker 1 [T1 ] 0.33 dBm 2.464429487 GHz A 10 1 PK 1 VIEW 0 LVL -10 -20 -30 3DB -40 2 -50 -60 -70 -80 Center 2.4835 GHz 10 MHz/ Span 100 MHz Date: 28.JUL.2014 15:10:36 Figure 8.5-15: Conducted spurious 802.11g, upper band edge Report reference ID: 264561-1TRFWL Page 29 of 33

Section 8 Testing data Test name FCC 15.247(d) and RSS-210 A8.5 Spurious (out-of-band) emissions Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.5.4 Test data, continued 55 90 85 50 80 75 45 70 40 65 Level in dBµV/m Level in dBµV/m 60 35 55 50 30 45 25 40 35 20 30 25 15 30M 50 60 80 100M 200 300 400 500 800 1G 20 Frequency in Hz 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Figure 8.5-16: Radiated Spurious 30-1000 MHz Figure 8.5-17: Radiated Spurious 1-18 GHz Table 8.5-4: Radiated band edge emissions within restricted bands Frequency, Peak level, dBµV/m Margin, Average level, dBµV/m Margin, Modulation Channel MHz Measured Limit dB Measured Limit dB Low 2390 52.55 74 21.45 52.55 54 1.45 802.11b High 2483.5 51.89 74 22.11 51.89 54 2.11 Low 2390 63.20 74 10.80 52.82 54 1.18 802.11g High 2483.5 62.81 74 11.19 53.25 54 0.75 Low 2390 67.33 74 6.67 53.62 54 0.38 802.11n High 2483.5 64.51 74 9.49 53.72 54 0.28 Report reference ID: 264561-1TRFWL Page 30 of 33

Section 8 Testing data Test name FCC Clause 15.247(e) and RSS-210 A8.2(b) Power spectral density for digitally modulated devices Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.6 FCC 15.247(e) and RSS-210 A8.2(b) Power spectral density for digitally modulated devices 8.6.1 Definitions and limits FCC: For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determined in accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall be used to determine the power spectral density. IC: The transmitter power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission or over 1.0 second if the transmission exceeds 1.0-second duration. This power spectral density shall be determined in accordance with the provisions of Section A8.4(4); (i.e. the power spectral density shall be determined using the same method for determining the conducted output power). 8.6.2 Test summary Test date July 28, 2014 Temperature 21 °C Test engineer Kevin Rose Air pressure 1003 mbar Verdict Pass Relative humidity 38 % 8.6.3 Observations, settings and special notes The test was performed using method described in section 10.2 Method PKPSD (EUT transmitting at full power throughout each sweep) of 558074 D01 DTS Meas Guidance v03r02. Spectrum analyser settings: Peak Detector was used as worst case. Resolution bandwidth Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz. Video bandwidth Set the VBW ≥ 3 × RBW. Frequency span 30 MHz Detector mode Peak Trace mode Max hold. Sweeps Allow trace to fully stabilize. 8.6.4 Test data Table 8.6-1: PSD measurements results Modulation Frequency, MHz PSD, dBm/100 kHz PSD limit, dBm/3 kHz Margin, dB 2412 1.66 8 6.34 802.11b 2437 4.08 8 3.92 2462 2.17 8 5.83 2412 1.12 8 6.88 802.11g 2437 3.16 8 4.84 2462 1.29 8 6.71 2412 0.42 8 7.58 802.11n 2437 3.01 8 4.99 2462 0.50 8 7.50 Report reference ID: 264561-1TRFWL Page 31 of 33

Section 8 Testing data Test name FCC Clause 15.247(e) and RSS-210 A8.2(b) Power spectral density for digitally modulated devices Specification FCC Part 15 Subpart C and RSS-210, Issue 8 8.6.4 Test data, continued * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 1.66 dBm VBW 300 kHz 1.29 dBm Ref 36.4 dBm * Att 20 dB SWT 10 ms 2.411487179 GHz Ref 36.4 dBm * Att 20 dB SWT 10 ms 2.464500000 GHz Offset 11.4 dB Offset 11.4 dB 30 30 A A 1 PK 1 PK 20 20 MAXH MAXH LVL LVL 10 10 1 1 0 0 -10 -10 -20 3DB -20 3DB -30 -30 -40 -40 -50 -50 -60 -60 Center 2.412 GHz 2 MHz/ Span 20 MHz Center 2.462 GHz 2 MHz/ Span 20 MHz Date: 28.JUL.2014 16:27:24 Date: 28.JUL.2014 16:30:35 Figure 8.6-1: PSD sample plot on 802.11b Figure 8.6-2: PSD sample plot on 802.11g * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 3.01 dBm Ref 36.4 dBm * Att 20 dB SWT 10 ms 2.438282051 GHz Offset 11.4 dB 30 A 1 PK 20 MAXH LVL 10 1 0 -10 -20 3DB -30 -40 -50 -60 Center 2.437 GHz 2 MHz/ Span 20 MHz Date: 28.JUL.2014 16:28:55 Figure 8.6-3: PSD sample plot on 802.11n Report reference ID: 264561-1TRFWL Page 32 of 33

Section 9: Block diagrams of test set-ups Section 9. Block diagrams of test set-ups 9.1 Radiated emissions set-up Radio absorbing material Antenna mast Test antenna 4m 3m Test EUT antenna Non- conducting table 1m 0.8 m Metal ground plane Turn table Receiver 9.2 Conducted emissions set-up Vertical ground plane 40 cm from EUT EUT 0.8 m Power supply Non- LISN conducting table 0.8 m Horizontal ground plane Receiver Report reference ID: 264561-1TRFWL Page 33 of 33


Document Created: 2014-09-25 12:52:22
Document Modified: 2014-09-25 12:52:22
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC