Test Report for PCB_part 24

FCC ID: YR8ES710

Test Report

Download: PDF
FCCID_2566555

Report No.: RXA1502-0023RF02R2 Page 1of 33 TESTING No. L2264 Part 24 TEST REPORT Product Name GPS Tracker Model Name ES710 Brand Name eSky FCC ID YR8ES710 Applicant eSky wireless Inc. Manufacturer ASIATELCO TECHNOLOGIES CO. Date of issue March 20, 2015 TA Technology (Shanghai) Co., Ltd.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 2of 33 GENERAL SUMMARY FCC CFR47 Part 2 (2013) Frequency Allocations And Radio Treaty Matters; General Rules And Regulations FCC CFR47 Part 24E (2013) Personal Communications Services Reference Standard(s) ANSI/TIA-603-C(2004) Land mobile FM or PM Communications Equipment Measurements and Performance Standards. KDB 971168 D01 Power Meas License Digital Systems v02r02 Measurement Guidance for Certification of Licensed Digital Transmitters This fixed wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 2 of this test report are below limits specified in the relevant standards. Conclusion General Judgment: Pass Comment The test result only responds to the measured sample. Approved by Revised by Performed by Kai Xu Lingling Kang Changxu Wan Director RF Manager RF Engineer

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 3of 33 TABLE OF CONTENT 1. General Information ..................................................................................................................... 4 1.1. Notes of the test report .........................................................................................................4 1.2. Testing laboratory .................................................................................................................5 1.3. Applicant Information ............................................................................................................5 1.4. Manufacturer Information ......................................................................................................5 1.5. Information of EUT ................................................................................................................6 1.6. Test Date ..............................................................................................................................6 2. Test Information ........................................................................................................................... 7 2.1. Summary of test results ........................................................................................................7 2.2. RF Power Output ..................................................................................................................7 2.3. Effective Isotropic Radiated Power .....................................................................................10 2.4. Occupied Bandwidth ...........................................................................................................12 2.5. Band Edge Compliance ......................................................................................................15 2.6. Peak-to-Average Power Ratio (PAPR) ...............................................................................18 2.7. Frequency Stability .............................................................................................................21 2.8. Spurious Emissions at Antenna Terminals .........................................................................23 2.8 Radiates Spurious Emission ...............................................................................................27 3. Main Test Instruments ................................................................................................................ 31 ANNEX A: EUT Appearance and Test Setup ..................................................................................... 32 A.1 EUT Appearance ................................................................................................................32 A.2 Test Setup ...........................................................................................................................33

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 4of 33 1. General Information 1.1. Notes of the test report TA Technology (Shanghai) Co., Ltd. has obtained the accreditation of China National Accreditation Service for Conformity Assessment (CNAS), and accreditation number: L2264. TA Technology (Shanghai) Co., Ltd. has been listed on the US Federal Communications Commission list of test facilities recognized to perform electromagnetic emissions measurements. The site recognition number is 428261. TA Technology (Shanghai) Co., Ltd. has been listed by industry Canada to perform electromagnetic emission measurement. The site recognition number is 8510A. TA Technology (Shanghai) Co., Ltd. guarantees the reliability of the data presented in this test report, which is the results of measurements and tests performed for the items under test on the date and under the conditions stated in this test report and is based on the knowledge and technical facilities available at TA Technology (Shanghai) Co., Ltd. at the time of execution of the test. TA Technology (Shanghai) Co., Ltd. is liable to the client for the maintenance by its personnel of the confidentiality of all information related to the items under test and the results of the test. The sample under test was selected by the Client.This report only refers to the item that has undergone the test. This report standalone dose not constitute or imply by its own an approval of the product by the certification Bodies or competent Authorities. This report cannot be used partially or in full for publicity and/or promotional purposes without previous written approval of TA Technology (Shanghai) Co., Ltd. and the Accreditation Bodies, if it applies. If the electrical report is inconsistent with the printed one, it should be subject to the latter.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 5of 33 1.2. Testing laboratory Company: TA Technology (Shanghai) Co., Ltd. Address: No.145, Jintang Rd, Tangzhen Industry Park, Pudong City: Shanghai Post code: 201201 Country: P. R. China Contact: Xu Kai Telephone: +86-021-50791141/2/3 Fax: +86-021-50791141/2/3-8000 Website: http://www.ta-shanghai.com E-mail: xukai@ta-shanghai.com 1.3. Applicant Information Company: eSky wireless Inc. A311#,258,Road Ren'ai Suzhou 215021 Address: PR.China 1.4. Manufacturer Information Company: AsiaTelco Technologies Co. #289 Bisheng Road, Building-8, 3F, Zhangjiang Hi-Tech Park, Pudong, Address: Shanghai-201204, China

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 6of 33 1.5. Information of EUT General information MEID: A100003230B9D6 Hardware Version: P1 Software Version: 1.1.67T Antenna Type: Internal Antenna Device Operating Configurations: Test Mode(s): CDMA PCS: Support mode: 1x RTT Test Modulation: QPSK Maximum E.I.R.P. 22.36 dBm Rated Power Supply Voltage: 12V Extreme Voltage: Minimum: 6V Maximum: 40V Extreme Temperature: Lowest: -40°C Highest: +80°C Test Channel: 25 - 600 - 1175 (CDMA PCS) (tested) (Low - Middle - High) Band Tx (MHz) Rx (MHz) Operating Frequency Range(s) CDMA PCS 1851.25 ~ 1908.75 1931.25 ~ 1988.75 1.6. Test Date The test is performed from February 10, 2015 to February 12, 2015.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 7of 33 2. Test Information 2.1. Summary of test results Number Test Case Clause in FCC rules Verdict 1 RF power output 2.1046 PASS 2 Effective Isotropic Radiated power 24.232 PASS 3 Occupied Bandwidth 2.1049 PASS 4 Band Edge Compliance 24.238 PASS 5 Peak-to-Average Power Ratio KDB 971168 D01(5.7) PASS 6 Frequency Stability 2.1055 / 24.235 PASS 7 Spurious Emissions at Antenna Terminals 2.1051 / 24.238 PASS 8 Radiates Spurious Emission 2.1053 / 24.238 PASS PASS: The EUT complies with the essential requirements in the standard. FAIL: The EUT does not comply with the essential requirements in the standard.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 8of 33 2.2. RF Power Output Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Methods of Measurement During the process of the testing, The EUT is controlled by the Base Station Simulator to ensure max power transmission and proper modulation. Test Setup The loss between RF output port of the EUT and the input port of the tester has been taken into consideration. Limits No specific RF power output requirements in part 2.1046. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.4 dB.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 9of 33 Test Results Conducted Power(dBm) CDMA PCS Channel 25 Channel 600 Channel 1175 1851.25 (MHz) 1880 (MHz) 1908.75 (MHz) +F-SCH 23.18 23.12 22.62 SO32 +SCH 22.96 22.74 22.64 Note: 1) The maximum RF Output Power numbers are marks in bold. 2) The following testing is set to +F-SCH based on the maximum RF Output Power.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 10of 33 2.3. Effective Isotropic Radiated Power Ambient condition Temperature Relative humidity 21°C ~25°C 40%~60% Methods of Measurement The measurement procedures in TIA- 603C are used. 1. The EUT was placed on a turntable with 1.5 meter height in a fully anechoic chamber. 2. The EUT was set at 3 meters from the receiving antenna, which was mounted on the antenna tower. 3. GSM operating modes: Set RBW= 1MHz, VBW= 3MHz, RMS detector over burst; UMTS operating modes: Set RBW= 100 KHz, VBW= 300 KHz, RMS detector over frame, and use channel power option with bandwidth=5MHz, per section 4.0 of KDB 971168 D01. 4. The table was rotated 360 degrees to determine the position of the highest radiated power. 5. The height of the receiving antenna is adjusted to look for the maximum ERP/EIRP. 6. Taking the record of maximum ERP/EIRP. 7. A dipole antenna was substituted in place of the EUT and was driven by a signal generator. 8. The conducted power at the terminal of the dipole antenna is measured. 9. Repeat step 3 to step 5 to get the maximum ERP/EIRP of the substitution antenna. 10. ERP/EIRP = Ps + Et – Es + Gs = Ps + Rt – Rs + Gs Ps (dBm)：Input power to substitution antenna. Gs (dBi or dBd)：Substitution antenna Gain. Et = Rt + AF Es = Rs + AF AF (dB/m)：Receive antenna factor Rt：The highest received signal in spectrum analyzer for EUT. Rs：The highest received signal in spectrum analyzer for substitution antenna. Test Setup

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 11of 33 Limits Rule Part 24.232(b) specifies that "Mobile/portable stations are limited to 2 watts EIRP. Peak power” and Rule Part 24.232(c) specifies that "Peak transmit power must be measured over any interval of continuous transmission using instrumentation calibrated in terms of an rms-equivalent voltage”. Limit (EIRP) ≤ 2 W (33 dBm) Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 1.19 dB Test Results:Pass Rt Rs Ps Gs E.I.R.P. Mode Channel Polarization (dBm) (dBm) (dBm) (dBi) (dBm) 25 Vertical -36.81 -53.71 0 1.92 18.82 600 Vertical -37.71 -53.91 0 1.94 18.14 1175 Vertical -39.31 -54.55 0 1.92 17.16 CDMA PCS 25 Horizontal -33.35 -53.19 0 1.92 21.76 600 Horizontal -33.00 -53.42 0 1.94 22.36 1175 Horizontal -34.70 -53.64 0 1.92 20.86 Note: 1. EIRP= E.R.P+2.15

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 12of 33 2.4. Occupied Bandwidth Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to Spectrum Analyzer and Base Station Simulator via power Splitter. The occupied bandwidth is measured using spectrum analyzer. RBW is set to 30kHz, VBW is set to 300kHz for CDMA PCS. 99% power and -26dBc occupied bandwidths are recorded. Spectrum analyzer plots are included on the following pages. Test Setup Limits No specific occupied bandwidth requirements in part 2.1049. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 624Hz.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 13of 33 Test Result 99% Power -26dBc CDMA PCS Channel Frequency (MHz) Bandwidth (MHz) Bandwidth(MHz) 25 1851.25 1.2636 1.437 +F-SCH 600 1880.0 1.2664 1.427 1175 1908.75 1.2667 1.428 CDMA PCS +F-SCH CH25 Occupied Bandwidth

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 14of 33 CDMA PCS +F-SCH CH600 Occupied Bandwidth CDMA PCS +F-SCH CH1175 Occupied Bandwidth

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 15of 33 2.5. Band Edge Compliance Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to Spectrum Analyzer and Base Station Simulator via power Splitter. The band edge of the lowest and highest channels were measured. The Average detector is used and RBW is set to 15kHz, VBW is set to 30kHz for CDMA PCS. Spectrum analyzer plots are included on the following pages. Test Setup Limits Rule Part 24.238(a) specifies that “on any frequency outside a licensee's frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log10 (P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 1.96, U=0.684dB.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 16of 33 Test Result: Carrier Reference value CDMA PCS frequency Limit Conclusion (dBm) (MHz) 1850.0 -33.061 -13 PASS +F-SCH 1910.0 -34.983 -13 PASS CDMA PCS +F-SCH 25 Channel

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 17of 33 CDMA PCS +F-SCH 1175 Channel

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 18of 33 2.6. Peak-to-Average Power Ratio (PAPR) Ambient condition Temperature Relative humidity 21°C ~25°C 40%~60% Methods of Measurement The measurement procedures in KDB971168 are used. The inherent randomness of the power peaks in a noise-like signal makes it difficult to quantify the peak power using traditional measurement techniques for determining the peak power of an analog signal. The peak power of a digitally-modulated signal is predictable only on a statistical basis. Thus, for these types of signals, a statistical measurement of the peak power is necessary. Power Complementary Cumulative Distribution Function (CCDF) curves provide a means for characterizing the power peaks of a digitally modulated signal on a statistical basis. A CCDF curve depicts the probability of the peak signal amplitude exceeding the average power level. Most contemporary measurement instrumentation include the capability to produce CCDF curves for an input signal provided that the instrument’s resolution bandwidth can be set wide enough to accommodate the entire input signal bandwidth. Step 1. The EUT was connected to Spectrum Analyzer and Base Station via power divider. Step 2. Set the CCDF option in Spectrum analyzer. Step 3. Record the maximum PAPR level associated with a probability of 0.1%. Test Setup Limits No specific Peak-to-Average Ratio requirements in KDB 971168. Measurement Uncertainty The assessed measurement uncertainty to ensure 95% confidence level for the normal distribution is with the coverage factor k = 2, U= 0.4 dB.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 19of 33 Test Result: Mode Channel Frequency (MHz) Test Result(dB) 25 1851.25 3.67 +F-SCH 600 1880.0 3.87 1175 1908.75 3.91 CDMA PCS +F-SCH CH25 Channel

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 20of 33 CDMA PCS +F-SCH CH600 Channel CDMA PCS +F-SCH CH1175 Channel

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 21of 33 2.7. Frequency Stability Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement 1. Frequency Stability (Temperature Variation) The temperature inside the climate chamber is varied from -40°C to +80°C in 10°C step size, (1) With all power removed, the temperature was decreased to -40°C and permitted to stabilize for three hours. (2) Measure the carrier frequency with the test equipment in a “call mode”. These measurements should be made within 1 minute of powering up the mobile station, to prevent significant self warming. (3) Repeat the above measurements at 10°C increments from -40°C to +80°C. Allow at least 1.5 hours at each temperature, un-powered, before making measurements. 2. Frequency Stability (Voltage Variation) The frequency stability shall be measured with variation of primary supply voltage as follows: (1) Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. (2) For hand carried, battery powered equipment, reduce primary supply voltage to the battery-operating end point which shall be specified by the manufacturer. This transceiver is specified to operate with an input voltage of between 6 V and 40 V, with a nominal voltage of 12V. Test setup

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 22of 33 Limits No specific frequency stability requirements in part 24.235 Measurement Uncertainty The assessed measurement uncertainty to ensure 99.75％ confidence level for the normal distribution is with the coverage factor k = 3, U= 0.01ppm. Test Result Test Results (ppm) / 12 V Power supply Temperature Channel 600 (°C) +F-SCH -40 -0.005521277 -30 -0.005824468 -20 -0.006159574 -10 -0.006037234 0 -0.00587234 10 -0.006154255 20 -0.006085106 30 -0.005930851 40 -0.006446809 50 -0.006414894 60 -0.006042553 70 -0.006691489 80 -0.006611702 Test Results(ppm) / 20°C Voltage Channel 600 (V) +F-SCH 6 -0.006670213 12 -0.006085106 40 -0.008765957

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 23of 33 2.8. Spurious Emissions at Antenna Terminals Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The EUT was connected to Spectrum Analyzer and Base Station Simulator via power Splitter. The measurement is carried out using a spectrum analyzer. The spectrum analyzer scans from 30MHz to the 10th harmonic of the carrier. For CDMA PCS, RBW and VBW are set to 100 kHz, Sweep is set to ATUO. Of those disturbances below (limit – 20 dB), the mark is not required for the EUT. Test setup Limits Rule Part 24.238(a) specifies that “on any frequency outside a licensee's frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log10 (P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 99.75％ confidence level for the normal distribution is with the coverage factor k = 1.96. Frequency Uncertainty 100kHz-2GHz 0.684 dB 2GHz-18GHz 1.407 dB

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 24of 33 Test Result CDMA PCS CH25 0 -5 -10 FCC CSE -15 -20 -25 -30 Level in dBm -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 30M 50 60 80 100M 200 300 400 500 800 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Note: The signal beyond the limit is carrier. CDMA PCS CH25 30MHz~18GHz 0 -10 FCC CSE -20 -30 -40 Level in dBm -50 -60 -70 -80 -90 -100 18 18.2 18.4 18.6 18.8 19 19.2 19.4 19.6 19.8 20 Frequency in GHz CDMA PCS CH25 18GHz ~20GHz

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 25of 33 CDMA PCS CH600 0 -5 -10 -15 -20 -25 -30 Level in dBm -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 30M 50 60 80 100M 200 300 400 500 800 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Note: The signal beyond the limit is carrier. CDMA PCS CH600 30MHz~18GHz 0 -10 FCC CSE -20 -30 -40 Level in dBm -50 -60 -70 -80 -90 -100 18 18.2 18.4 18.6 18.8 19 19.2 19.4 19.6 19.8 20 Frequency in GHz CDMA PCS CH600 18GHz ~20GHz

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 26of 33 CDMA PCS CH1175 0 -5 -10 -15 -20 -25 -30 Level in dBm -35 -40 -45 -50 -55 -60 -65 -70 -75 -80 30M 50 60 80 100M 200 300 400 500 800 1G 2G 3G 4G 5G 6 8 10G 18G Frequency in Hz Note: The signal beyond the limit is carrier. CDMA PCS CH1175 30MHz~18GHz 0 -10 FCC CSE -20 -30 -40 Level in dBm -50 -60 -70 -80 -90 -100 18 18.2 18.4 18.6 18.8 19 19.2 19.4 19.6 19.8 20 Frequency in GHz CDMA PCS CH1175 18GHz ~20GHz

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 27of 33 2.8 Radiates Spurious Emission Ambient condition Temperature Relative humidity Pressure 23°C ~25°C 45%~50% 101.5kPa Method of Measurement The measurements procedures in TIA -603C are used. The spectrum was scanned from 30 MHz to the 10th harmonic of the highest frequency generated within the equipment. The procedure of Radiates Spurious Emission is as follows: Step 1: The measurement is carried out in the semi-anechoic chamber. EUT was placed on a 1.5 meters high non-conductive table at a 3 meters test distance from the test receive antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT. A radio link shall be established between EUT and Tester. The output power of the cell signal of the tester will be decreased until the output power of the EUT reach a maximum value. A peak detector is used while RBW and VBW are both set to 3MHz. During the measurement, the highest emission was recorded from analyzer power level (LVL) from the 360 degrees rotation of the turntable and the test antenna moved up and down over a range from 1 to 4 meters in both horizontally and vertically polarized orientations. The test setup refers to figure below. Step 2: A dipole antenna shall be substituted in place of the EUT. The antenna will be driven by a signal generator with a adjustable S.G. applied through a Tx cable. Adjust the level of the signal generator output until the value of the receiver reach the previously recorded analyzer power level (LVL).Then The E.R.P. /E.I.R.P. of the EUT can be calculated through the level of the signal generator, Tx cable loss and the gain of the substitution antenna. The test setup refers to figure below.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 28of 33 E.R.P（peak power）=S.G. - Tx Cable loss + Substitution antenna gain – 2.15. EIRP= E.R.P+2.15 The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in stand-up position (Z axis) and the antenna is vertical. Of those disturbances below (limit – 20 dB), the mark is not required for the EUT. Limits Rule Part 24.238(a) specifies that “on any frequency outside a licensee's frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log10 (P) dB.” Limit -13 dBm Measurement Uncertainty The assessed measurement uncertainty to ensure 95％ confidence level for the normal distribution is with the coverage factor k = 1.96, U= 3.55 dB.

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 29of 33 Test Result CDMA Cellular CH1013 TX ch.1013 Cable ERP SG Gain Antenna Limit Margin Azimuth Harmonic Frequency Loss Level (dBm) (dBi) Polarization (dBm) (dB) (deg) (MHz) (dB) (dBm) 2 1649.6 -45.21 2 10.15 Vertical -46.45 -13 33.45 270 3 2474.1 -66.74 2.51 11.35 Vertical -60.05 -13 47.05 0 4 3478.5 -64.45 4.2 10.85 Vertical -46.26 -13 33.26 225 5 4123.5 -62.89 5.2 11.35 Vertical -58.89 -13 45.89 90 6 4947.4 -63.43 5.5 11.95 Vertical -50.39 -13 37.39 225 7 5774.6 -61.76 5.7 13.55 Vertical -42.59 -13 29.59 315 8 6594.8 -61.10 6.3 13.75 Vertical -46.93 -13 33.93 270 9 7419.4 -61.08 6.8 13.85 Vertical -48.08 -13 35.08 180 10 8249.6 -61.86 6.9 14.25 Vertical -39.76 -13 26.76 270 Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2.We tested the vertical and horizontal polarization in the preliminary test and the vertical polarization are selected as the worst condition, CDMA Cellular CH384 TX ch.384 Cable ERP SG Gain Antenna Limit Margin Azimuth Harmonic Frequency Loss Level (dBm) (dBi) Polarization (dBm) (dB) (deg) (MHz) (dB) (dBm) 2 1672.3 -50.43 2 10.75 Vertical -39.66 -13 26.66 180 3 2509.56 -62.78 2.51 11.05 Vertical -56.39 -13 43.39 0 4 3526.2 -64.61 4.2 11.15 Vertical -46.24 -13 33.24 180 5 4182.6 -62.67 5.2 11.15 Vertical -58.87 -13 45.87 90 6 5019.12 -61.23 5.5 11.95 Vertical -56.93 -13 43.93 0 7 5856.8 -62.70 5.7 13.55 Vertical -42.48 -13 29.48 315 8 6694.1 -61.77 6.3 13.75 Vertical -48.78 -13 35.78 270 9 7528.68 -60.26 6.8 13.85 Vertical -55.36 -13 42.36 0 10 8365.9 -61.88 6.9 14.25 Vertical -49.23 -13 36.23 270 Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2.We tested the vertical and horizontal polarization in the preliminary test and the vertical polarization are selected as the worst condition,

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 30of 33 CDMA Cellular CH777 TX ch.777 Cable ERP SG Gain Antenna Limit Margin Azimuth Harmonic Frequency Loss Level (dBm) (dBi) Polarization (dBm) (dB) (deg) (MHz) (dB) (dBm) 2 1697.1 -55.04 2 10.15 Vertical -40.51 -13 27.51 270 3 2544.93 -56.6 2.51 11.05 Vertical -50.21 -13 37.21 0 4 3573.0 -64.16 4.2 11.15 Vertical -45.37 -13 32.37 0 5 4241.55 -61.50 5.2 11.15 Vertical -57.70 -13 44.70 180 6 5089.86 -62.89 5.5 11.95 Vertical -58.59 -13 45.59 90 7 5936.3 -63.04 5.7 13.55 Vertical -45.31 -13 32.31 0 8 6786.48 -60.84 6.3 13.75 Vertical -55.54 -13 42.54 270 9 7632.8 -60.52 6.8 13.85 Vertical -47.67 -13 34.67 45 10 8483.3 -62.22 6.9 14.25 Vertical -49.65 -13 36.65 225 Note: 1.The other Spurious RF Radiated emissions level is no more than noise floor. 2.We tested the vertical and horizontal polarization in the preliminary test and the vertical polarization are selected as the worst condition,

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 31of 33 3. Main Test Instruments Calibration Expiration Valid No. Name Type Manufacturer Serial Number Date Time Period Base Station 01 CMU200 R&S 118133 2014-05-26 2015-05-25 1 year Simulator SHX-GF2 02 Power Splitter Hua Xiang 10120101 NA NA NA -2-13 Spectrum 03 E4445A Agilent MY46181146 2014-05-26 2015-05-25 1 year Analyzer Universal Radio 04 Communication E5515C Agilent MY48367192 2014-05-26 2015-05-25 1 year Tester 05 Signal Analyzer FSV30 R&S 100815 2014-05-26 2015-05-25 1 year Signal SMB 06 R&S 102594 2014-05-26 2015-05-25 1 year generator 100A EMI Test 07 ESCI R&S 100948 2014-05-26 2015-05-25 1 year Receiver VUBL SCHWARZBE 08 Trilog Antenna 9163-201 2012-06-19 2015-06-18 3 years 9163 CK VUBL SCHWARZBE 09 Trilog Antenna 9163-391 2012-06-19 2015-06-18 3 years 9163 CK 10 Horn Antenna HF907 R&S 100126 2012-07-01 2015-06-30 3 years 11 Horn Antenna HF907 R&S 100125 2012-07-01 2015-06-30 3 years Climatic 12 PT-30B Re Ce 20101891 2014-09-01 2017-08-31 3 years Chamber 13 Horn Antenna 3160-09 ETS-Lindgren 00102643 2012-05-17 2015-05-16 3 years 14 Horn Antenna 3160-09 ETS-Lindgren 00102644 2012-05-17 2015-05-16 3 years SMA Two 15 RF Cable Agilent 0001 2015-02-09 2015-04-08 15cm months *****END OF REPORT *****

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 32of 33 ANNEX A: EUT Appearance and Test Setup A.1 EUT Appearance Picture 1 EUT and Auxiliary

TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1502-0023RF02R2 Page 33of 33 A.2 Test Setup Picture 2: Radiated Spurious Emissions Test setup


Document Created: 2015-03-20 18:12:44
Document Modified: 2015-03-20 18:12:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC