I19Z60700-SEM01_SAR_Rev1_Part5

FCC ID: YAMPNC550B9

RF Exposure Info

Download: PDF
FCCID_4368942

Calibratio ; n Laboratory of N/z ty St‘s S Schweizerischer Kalibrierdienst Schmid & Partner ila‘ \—/E“E—!'_ c Service suisse d‘étalonnage Englneenng AG T nds Servizio svizzero di taratura a m zz\wy Zeughausstrasse 43, 8004 Zurich, Switzerland *4/fi\\y‘ S Swiss Calibration Service Arolale Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) EC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2450V2—853_Jul17 Page 2 of 8

() S Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version Extrapolation Phantom Distance Dipole Center — TSL DASY5 Advanced Extrapolation Modular Flat Phantom 10 mm V52.10.0 with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2450 MHz # 1 MHz Head TSL barameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.2 1.80 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 37.8 x 6 % 1.87 mho/m # 6 % Head TSL temperature change during test <0.5 °C SAR result with Head TSL SAR averaged over 1 cm‘ (1 g) of Head TSL Condition SAR measured 250 mW input power 13.4 Wikg SAR for nominal Head TSL parameters normalized to 1W 52.2 Wikg a 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.26 Wikg SAR for nominal Head TSL parameters normalized to 1W 24.7 Wikg 2 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C §2.7 1.95 mho/m Measured Body TSL parameters (22.0 £0.2) °C 52.1 #6% 2.04 mho/m £ 6 % Body TSL temperature change during test <0.5 °C a~— ———— SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 12.9 Wikg SAR for nominal Body TSL parameters normalized to 1W 50.4 Wikg 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.03 W/kg SAR for nominal Body TSL parameters normalized to 1W 23.8 Wikg x 16.5 % (k=2) Certificate No: D2450V2—853_Jul1 7 Page 3 of 8 ~ o crucce

Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 52.0 Q + 5.0 jQ Return Loss —25.6 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 49.6 Q + 6.3 jQ Return Loss —24.0 dB General Antenna Parameters and Design IEectrical Delay (one direction) [ 1.161 ns 41 After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductorof the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on November 10, 2009 Certificate No: D2450V2—853_Jul17 Page 4 of 8

DASY5 Validation Report for Head TSL Date: 20.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 853 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 1.87 $/m; s = 37.8; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(8.12, 8.12, 8.12); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 112.7 V/m; Power Drift = —0.00 dB Peak SAR (extrapolated) = 27.0 W/kg SAR(1 g) = 13.4 W/kg; SAR(10 g) = 6.26 W/kg Maximum value of SAR (measured) = 21.5 W/kg dB 0 ~4.00 —8.00 —12.00 —16.00 —20.00 0 dB = 21.5 W/kg = 13.32 dBW/kg Certificate No: D2450V2—853_Jul17 Page 5 of 8 ~ o nu ce —

© Impedance Measurement Plot for Head TSL 20 Jul 2017 11:54:15 CHZ sii 1 U FS 4151965 a 4.9570 a 322.01 pH 2 450.000 000 MHz aer T . Av 188 H1d CH2 Ca Av 16° H1d START 2 250.000 @00 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—853_Jul17 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 21.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 853 Communication System: UID 0 — CW; Frequency: 2450 MHz Medium parameters used: f = 2450 MHz; 0 = 2.04 $/m; & = 52.1; p = 1000 kg/m‘ Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(8.1, 8.1, 8.1); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 & DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 104.1 V/m; Power Drift = —0.09 dB Peak SAR (extrapolated) = 25.5 W/kg SAR(I g) = 12.9 W/kg; SAR(10 g) = 6.03 W/kg Maximum value of SAR (measured) = 20.0 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 20.0 W/kg = 13.01 dBW/kg Certificate No: D2450V2—853_Jul17 Page 7 of 8

© Impedance Measurement Plot for Body TSL 21 Jul 2017 14142134 CHZ sii i uo rs 1149.619 a 6.2656 2 407.02 pH 2450.000 000 MHz — _ fAvg 16 H1d CH2 Ca Av 16" H1d START 2 250.000 000 MHz STOP 2 650.000 000 MHz Certificate No: D2450V2—853_Jul17 Page 8 of 8

& duveve y arik ame m k pecme ewe n nrneme n ne n n n n o on n en n en Calibration Laboratory of wl/7 S Schweizerischer Kalibrierdienst )§ & Schmid & Partner 9. Service suisse d‘étalonnage Engineering AG Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland LN3 Swiss Calibration Service Zulitabs® Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client CTTL—BJ (Auden) Certificate No: D2600V2—1012_Jul17 CALIBRATION CERTIFICATE Object D2600V2 — SN:1012 Calibration procedure(s) QA CAL—05.v9 Calibration procedure for dipole validation kits above 700 MHz Calibration date: July 21, 2017 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 04—Apr—17 (No. 217—02521/02522) Apr—18 Power sensor NRP—Z291 SN: 103244 04—Apr—17 (No. 217—02521) Apr—18 Power sensor NRP—Z291 SN: 108245 04—Apr—17 (No. 217—02522) Apr—18 Reference 20 dB Attenuator SN: 5058 (20k) 07—Apr—17 (No. 217—02528) Apr—18 Type—N mismatch combination SN: 5047.2 / 06827 O7—Apr—17 (No. 217—02529) Apr—18 Reference Probe EX3DV4 SN: 7349 31—May—17 (No. EX3—7349_May17) May—18 DAE4 SN: 601 28—Mar—17 (No. DAE4—601_Mar17) Mar—18 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter EPM—442A SN: GB37480704 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: US37202783 07—Oct—15 (in house check Oct—16) In house check: Oct—18 Power sensor HP 8481A SN: MY41092317 07—Oct—15 (in house check Oct—16) In house check: Oct—18 RF generator R&S SMT—06 SN: 100972 15—Jun—15 (in house check Oct—16) In house check: Oct—18 Network Analyzer HP 8753E SN: US37390585 18—Oct—01 (in house check Oct—16) In house check: Oct—17 Name Function Si ture Calibrated by: Michael Weber Laboratory Technician s Approved by: Katja Pokovic Technical Manager //%% Issued: July 24, 2017 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: D2600V2—1012_Jul17 Page 1 of 8 ~ onz s —

Calibn:ation Laboratory of s\o\‘;i‘\ijj'm,,’ Schmid & Partner ilfi%./{@ S Schweizerischer Kalibrierdienst Service suisse d‘étalonnage Engineering AG yyp: l C Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland €4,/fi\\x} S Swiss Calibration Service "thilale Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Glossary: TSL tissue simulating liquid ConvrF sensitivity in TSL / NORM x,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "[EEE Recommended Practice for Determining the Peak Spatial— Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for the assessment of Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c) IEC 62209—2, "Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz)", March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: e Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. e Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. e Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. e SAR measured: SAR measured at the stated antenna input power. e SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. e SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: D2600V2—1012_Jul17 Page 2 of 8 ,,,,,,,,

(iléfll, Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2600 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.0 1.96 mho/m Measured Head TSL parameters (22.0 + 0.2) °C 37.2 46 % 2.04 mho/m + 6 % Head TSL temperature change during test <0.5 °C —— SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 14.9 W/kg SAR for nominal Head TSL parameters normalized to 1W 57.9 Wikg + 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.57 Wi/kg SAR for nominal Head TSL parameters normalized to 1W 25.8 Wikg a 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.5 216 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 51.6 4 6 % 2.22 mho/m + 6 % Body TSL temperature change during test <0.5 °C ~~~ _ SAR result with Body TSL SAR averaged over 1 cm* (1 g) of Body TSL Condition SAR measured 250 mW input power 14.1 W/kg SAR for nominal Body TSL parameters normalized to 1W 55.5 Wikg + 17.0 % (k=2) SAR averaged over 10 cm‘ (10 g) of Body TSL condition SAR measured 250 mW input power 6.25 W/kg SAR for nominal Body TSL parameters normalized to 1W 24.8 Wikg # 16.5 % (k=2) Certificate No: D2600V2—1012_Jul17 Page 3 of 8

(uém» Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance, transformed to feed point 46.8 Q — 5.0 jQ Return Loss — 24.2 dB Antenna Parameters with Body TSL Impedance, transformed to feed point 43.5 0 — 5.3 jQ Return Loss —21.0 dB General Antenna Parameters and Design [ Electrical Delay (one direction) 1.151 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Manufactured on October 30, 2007 Certificate No: D2600V2—1012_Jul17 Page 4 of 8

_: | @77T,L y 1O _ DASY5 Validation Report for Head TSL Date: 20.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN: 1012 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.04 S/m; & = 37.2; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASY5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvF(7.96, 7.96, 7.96); Calibrated: 31.05.2017; * Sensor—Surface: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 $n601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 «_ DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 113.6 V/m; Power Drift = 0.05 dB Peak SAR (extrapolated) = 32.3 W/kg SAR(1 g) = 14.9 W/kg; SAR(10 g) = 6.57 W/kg Maximum value of SAR (measured) = 25.0 W/kg dB 0 —5.00 —10.00 —15.00 —20.00 —25.00 0 dB = 25.0 W/kg = 13.98 dBW/kg Certificate No: D2600V2—1012_Jul17 Page 5 of 8

® Impedance Measurement Plot for Head TSL 20 Jul 2017 12:14:05 S11 1 U FS 5: 46.836 0 —5.0410 0 12143 pF 2 600.000 000 MHz ~~1 Del Ca Av 16 * H1d CH2 Ca Av 16s H1d START 2 400.000 000 MHz STOP 2 800.000 000 MHz Certificate No: D2600V2—1012_Jul17 Page 6 of 8

DASY5 Validation Report for Body TSL Date: 21.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D2600V2; Serial: D2600V2 — SN: 1012 Communication System: UID 0 — CW; Frequency: 2600 MHz Medium parameters used: f = 2600 MHz; 0 = 2.22 $/m; & = 51.6; p = 1000 kg/m* Phantom section: Flat Section Measurement Standard: DASYS5 (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: e Probe: EX3DV4 — SN7349; ConvF(7.94, 7.94, 7.94); Calibrated: 31.05.2017; e Sensor—Surface: 1.4mm (Mechanical Surface Detection) e Electronics: DAE4 Sn601; Calibrated: 28.03.2017 * Phantom: Flat Phantom 5.0 (back); Type: QD 000 P50 AA; Serial: 1002 e DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Body Tissue/Pin=250 mW, d=10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 106.6 V/m; Power Drift = —0.07 dB Peak SAR (extrapolated) = 30.1 W/kg SAR(I g) = 14.1 W/kg; SAR(10 g) = 6.25 W/ikg Maximum value of SAR (measured) = 23.4 W/kg dB 0 —5.20 ~10.40 —15.60 —20.80 —26.00 0 dB = 23.4 W/kg = 13.69 dBW/kg Certificate No: D2600V2—1012_Jul17 Page 7 of 8 ~ o us ~

mm TL y Impedance Measurement Plot for Body TSL 21 Jul 2017 14:S50:41 §11 1 U FS 1: 43.541. a —5.3223 a 11.501 pF 2 600.000 000 MHz Del Ca Av 16 * H1d CH2 Ca fivg 16 H1d START 2 400.000 000 MHz STOP 2 800.000 000 MHz Certificate No: D2600V2—1012_Jul17 Page 8 of 8

No. I19Z60700-SEM01 Page 199 of 202 ANNEX I Extended Calibration SAR Dipole Referring to KDB865664 D01, if dipoles are verified in return loss ( <-20dBm, within 20% of prior calibration), and in impedance ( within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. Justification of Extended Calibration SAR Dipole D750V3– serial no.1017 Head Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-19 -27.5 54.4 0.5 2018-7-17 -26.0 5.5 55.1 0.7 -1.0 -1.5 Body Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-19 -29.1 49.3 -3.4 2018-7-17 -29.3 -0.69 51.5 2.2 -3.1 0.3 Justification of Extended Calibration SAR Dipole D835V2– serial no.4d069 Head Real Imaginary Date of Return-Loss Delta Delta Impedance Delta (ohm) Impedance Measurement (dB) (%) (johm) (ohm) (johm) 2017-7-19 -32.4 52.1 -1.2 2018-7-17 -30.3 6.5 53.0 1.1 -1.0 0.2 Body Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-19 -26.9 47.9 -3.9 2018-7-17 -25.5 5.2 48.5 0.6 -5.0 -1.1 ©Copyright. All rights reserved by CTTL.

No. I19Z60700-SEM01 Page 200 of 202 Justification of Extended Calibration SAR Dipole D1750V2– serial no.1003 Head Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-21 -37.1 50.9 1.1 2018-7-19 -35.6 4.0 49.5 -1.4 -1.6 -2.7 Body Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-21 -30.2 47.0 0.1 2018-7-19 -27.6 8.6 46.0 -1.0 -0.3 -0.4 Justification of Extended Calibration SAR Dipole D1900V2– serial no.5d101 Head Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-26 -24.5 51.7 5.8 2018-7-24 -22.9 6.5 50.6 -1.1 7.2 1.4 Body Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-26 -22.0 46.2 6.6 2018-7-24 -21.4 2.7 46.4 0.2 7.4 0.8 ©Copyright. All rights reserved by CTTL.

No. I19Z60700-SEM01 Page 201 of 202 Justification of Extended Calibration SAR Dipole D2450V2– serial no.853 Head Real Imaginary Date of Return-Loss Delta Delta Delta Impedance Impedance Measurement (dB) (%) (ohm) (johm) (ohm) (johm) 2017-7-21 -25.6 52.0 5.0 2018-7-19 -23.1 9.8 53.6 1.6 6.3 1.3 Body Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-21 -24.0 49.6 6.3 2018-7-19 -22.0 8.3 50.4 0.8 8.0 1.7 Justification of Extended Calibration SAR Dipole D2600V2– serial no.1012 Head Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-21 -24.2 46.8 -5.0 2018-7-19 -23.7 2.1 47.7 0.9 -5.9 -0.9 Body Real Imaginary Date of Return-Loss Delta Delta Delta (%) Impedance Impedance Measurement (dB) (ohm) (johm) (ohm) (johm) 2017-7-21 -21.0 43.5 -5.3 2018-7-19 -22.4 -6.7 44.4 0.9 -4.5 0.8 ©Copyright. All rights reserved by CTTL.

No. I19Z60700-SEM01 Page 202 of 202 ANNEX J Accreditation Certificate ©Copyright. All rights reserved by CTTL.


Document Created: 2019-07-16 10:48:55
Document Modified: 2019-07-16 10:48:55
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC