Test report (DTS-BT LE) rev2

FCC ID: XPYNINAB30

Test Report

Download: PDF
FCCID_4481231

FCC Test Report (BT-LE) Report No.: RF181120C09D-2 FCC ID: XPYNINAB30 Test Model: NINA-B3 Received Date: Mar. 29, 2019 Test Date: Aug. 30 to Sep. 02, 2019 Issued Date: Sep. 20, 2019 Applicant: u-blox-AG Address: Zuercherstrasse 68 8800 Thalwil, Switzerland Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. Test Location: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. FCC Registration / 723255 / TW2022 Designation Number: This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF181120C09D-2 Page No. 1 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 Summary of Test Results ..................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information .............................................................................................................................. 6 3.1 General Description of EUT (BT-LE) ................................................................................................... 6 3.2 Description of Test Modes ................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail ............................................................................. 8 3.3 Duty Cycle of Test Signal .................................................................................................................. 10 3.4 Description of Support Units .............................................................................................................. 11 3.4.1 Configuration of System under Test .................................................................................................. 12 3.5 General Description of Applied Standards ........................................................................................ 13 4 Test Types and Results ...................................................................................................................... 14 4.1 Radiated Emission and Bandedge Measurement ............................................................................. 14 4.1.1 Limits of Radiated Emission and Bandedge Measurement .............................................................. 14 4.1.2 Test Instruments ................................................................................................................................ 15 4.1.3 Test Procedures ................................................................................................................................. 16 4.1.4 Deviation from Test Standard ............................................................................................................ 17 4.1.5 Test Setup .......................................................................................................................................... 17 4.1.6 EUT Operating Conditions................................................................................................................. 18 4.1.7 Test Results ....................................................................................................................................... 19 4.2 Conducted Emission Measurement .................................................................................................. 27 4.2.1 Limits of Conducted Emission Measurement .................................................................................... 27 4.2.2 Test Instruments ................................................................................................................................ 27 4.2.3 Test Procedures ................................................................................................................................. 28 4.2.4 Deviation from Test Standard ............................................................................................................ 28 4.2.5 Test Setup .......................................................................................................................................... 28 4.2.6 EUT Operating Conditions................................................................................................................. 28 4.2.7 Test Results ....................................................................................................................................... 29 4.3 Conducted Output Power Measurement ........................................................................................... 31 4.3.1 Limits of Conducted Output Power Measurement ............................................................................ 31 4.3.2 Test Setup .......................................................................................................................................... 31 4.3.3 Test Instruments ................................................................................................................................ 31 4.3.4 Test Procedures ................................................................................................................................. 31 4.3.5 Deviation from Test Standard ............................................................................................................ 31 4.3.6 EUT Operating Conditions................................................................................................................. 31 4.3.7 Test Results ....................................................................................................................................... 32 5 Pictures of Test Arrangements .......................................................................................................... 33 Appendix – Information of the Testing Laboratories ................................................................................. 34 Report No.: RF181120C09D-2 Page No. 2 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

Release Control Record Issue No. Description Date Issued RF181120C09D-2 Original release. Sep. 20, 2019 Report No.: RF181120C09D-2 Page No. 3 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

1 Certificate of Conformity Product: Stand-alone radio module Brand: u-blox-AG Test Model: NINA-B3 Sample Status: ENGINEERING SAMPLE Applicant: u-blox-AG Test Date: Aug. 30 to Sep. 02, 2019 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: Sep. 20, 2019 Claire Kuan / Specialist Approved by : , Date: Sep. 20, 2019 May Chen / Manager Report No.: RF181120C09D-2 Page No. 4 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.247) FCC Test Item Result Remarks Clause Meet the requirement of limit. 15.207 AC Power Conducted Emission PASS Minimum passing margin is -16.45dB at 0.44297MHz. 15.205 / Meet the requirement of limit. 15.209 / Radiated Emissions Measurement PASS Minimum passing margin is -9.4dB at 15.247(d) 2483.50MHz. 15.247(b) Conducted power PASS Meet the requirement of limit. Note: 1. Determining compliance based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. 2. This report is prepared for FCC Class II permissive change. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Expanded Uncertainty Measurement Frequency (k=2) (±) Conducted Emissions at mains ports 150kHz ~ 30MHz 1.8 dB 9kHz ~ 1GHz 3.0 dB Radiated Emissions up to 1 GHz 30MHz ~ 1GHz 5.1 dB 1GHz ~ 6GHz 5.1 dB Radiated Emissions above 1 GHz 6GHz ~ 18GHz 5.0 dB 18GHz ~ 40GHz 5.2 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF181120C09D-2 Page No. 5 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3 General Information 3.1 General Description of EUT (BT-LE) Product Stand-alone radio module Brand u-blox-AG Test Model NINA-B3 Status of EUT ENGINEERING SAMPLE Power Supply Rating DC 3.3V from host equipment Modulation Type GFSK Modulation Technology DTS Transfer Rate Up to 2Mbps Operating Frequency 2.402GHz ~ 2.480GHz Number of Channel 40 BT-LE 1M: 2.223mW Output Power BT-LE 2M: 2.218mW Antenna Type Refer to Note Antenna Connector Refer to Note Accessory Device NA Data Cable Supplied NA Note: 1. This report is prepared for FCC Class II permissive change. The difference compared with the original design is as the following information:  BLE Module Antenna trace layout design changed and antenna changed. 2. According to above conditions, only AC Power Conducted Emission, Radiated Emissions and Conducted power test items need to be performed. And all data were verified to meet the requirements. 3. The antennas provided to the EUT, please refer to the following table: Antenna Antenna Antenna Connector Cable Brand Model Net Gain Frequency range No. Type Type Length (dBi) BLE u-blox-AG 95XKAB15.G40 3.2 2.4~2.4835GHz Dipole i-pex(MHF) 97mm Antenna 4. Simultaneously transmission condition. Condition Technology 1 BT-LE WWAN (LTE) Note: The emission of the simultaneous operation has been evaluated and no non-compliance was found. 5. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. Report No.: RF181120C09D-2 Page No. 6 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3.2 Description of Test Modes 40 channels are provided to this EUT: FREQ. FREQ. FREQ. FREQ. CHANNEL CHANNEL CHANNEL CHANNEL (MHz) (MHz) (MHz) (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Report No.: RF181120C09D-2 Page No. 7 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3.2.1 Test Mode Applicability and Tested Channel Detail EUT APPLICABLE TO CONFIGURE DESCRIPTION MODE RE1G RE<1G PLC APCM - √ √ √ √ - RE1G: Radiated Emission above 1GHz & Where RE<1G: Radiated Emission below 1GHz Bandedge Measurement PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement NOTE: 1. The EUT’s antenna had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on X-plane. 2. “-” means no effect. Radiated Emission Test (Above 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) 0 to 39 0, 19, 39 GFSK 1 0 to 39 0, 19, 39 GFSK 2 Radiated Emission Test (Below 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) 0 to 39 0 GFSK 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) 0 to 39 0 GFSK 1 Report No.: RF181120C09D-2 Page No. 8 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

Antenna Port Conducted Measurement: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. AVAILABLE CHANNEL TESTED CHANNEL MODULATION TYPE DATA RATE (Mbps) 0 to 39 0, 19, 39 GFSK 1 0 to 39 0, 19, 39 GFSK 2 Test Condition: INPUT POWER APPLICABLE TO ENVIRONMENTAL CONDITIONS TESTED BY (SYSTEM) RE1G 23deg. C, 68%RH 120Vac, 60Hz Tom Yang RE<1G 23deg. C, 67%RH 120Vac, 60Hz Tom Yang PLC 25deg. C, 75%RH 120Vac, 60Hz Andy Ho APCM 22deg. C, 63%RH 120Vac, 60Hz Jyunchun Lin Report No.: RF181120C09D-2 Page No. 9 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3.3 Duty Cycle of Test Signal BT-LE 1M Duty cycle = 0.387 ms/0.625 ms = 0.619 BT-LE 2M Duty cycle = 0.201 ms/0.629 ms = 0.32 Report No.: RF181120C09D-2 Page No. 10 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3.4 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. ID Product Brand Model No. Serial No. FCC ID Remarks A. Test Tool NA NA NA NA Supplied by client B. Laptop Lenovo 80WG YD025N5Q NA Provided by Lab DC POWER C. Topward 6603D 795551 NA Provided by Lab SUPPLY Note: 1. All power cords of the above support units are non-shielded (1.8m). Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. DC Cable 1 1.8 No 0 Provided by Lab 2. Console Cable 1 0.235 Yes 0 Supplied by client Note: The core is originally attached to the cable. Report No.: RF181120C09D-2 Page No. 11 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3.4.1 Configuration of System under Test EUT (2) (A) Test Tool (B) Laptop (1) Under Table (C) DC Power Supply Report No.: RF181120C09D-2 Page No. 12 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

3.5 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.247) KDB 558074 D01 15.247 Meas Guidance v05r02 ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Note: The EUT has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF181120C09D-2 Page No. 13 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table. Other emissions shall be at least 20dB below the highest level of the desired power: Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 Note: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Report No.: RF181120C09D-2 Page No. 14 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.1.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010156 July 17, 2019 July 16, 2020 Agilent Pre-Amplifier EMC001340 980142 May 30, 2019 May 29, 2020 EMCI Loop Antenna EM-6879 264 Jan. 22, 2019 Jan. 21, 2020 Electro-Metrics RF Cable NA LOOPCAB-001 Jan. 14, 2019 Jan. 13, 2020 RF Cable NA LOOPCAB-002 Jan. 14, 2019 Jan. 13, 2020 Pre-Amplifier ZFL-1000VH2B AMP-ZFL-05 Apr. 30, 2019 Apr. 29, 2020 Mini-Circuits Trilog Broadband Antenna VULB 9168 9168-361 Nov. 22, 2018 Nov. 21, 2019 SCHWARZBECK RF Cable 8D 966-3-1 Mar. 18, 2019 Mar. 17, 2020 RF Cable 8D 966-3-2 Mar. 18, 2019 Mar. 17, 2020 RF Cable 8D 966-3-3 Mar. 18, 2019 Mar. 17, 2020 Fixed attenuator UNAT-5+ PAD-3m-3-01 Sep. 27, 2018 Sep. 26, 2019 Mini-Circuits Horn_Antenna BBHA9120-D 9120D-406 Nov. 25, 2018 Nov. 24, 2019 SCHWARZBECK Pre-Amplifier EMC12630SE 980384 Jan. 28, 2019 Jan. 27, 2020 EMCI RF Cable EMC104-SM-SM-1200 160922 Jan. 28, 2019 Jan. 27, 2020 RF Cable EMC104-SM-SM-2000 180601 June 10, 2019 June 09, 2020 RF Cable EMC104-SM-SM-6000 180602 June 10, 2019 June 09, 2020 Spectrum Analyzer N9030A MY54490679 July 17, 2019 July 16, 2020 Keysight Pre-Amplifier EMC184045SE 980387 Jan. 28, 2019 Jan. 27, 2020 EMCI Horn_Antenna BBHA 9170 BBHA9170519 Nov. 25, 2018 Nov. 24, 2019 SCHWARZBECK RF Cable EMC102-KM-KM-1200 160924 Jan. 28, 2019 Jan. 27, 2020 RF Cable EMC102-KM-KM-1200 160925 Jan. 28, 2019 Jan. 27, 2020 Software ADT_Radiated_V8.7.08 NA NA NA Antenna Tower & Turn Table MF-7802 MF780208406 NA NA Max-Full Boresight Antenna Fixture FBA-01 FBA-SIP01 NA NA Spectrum Analyzer FSV40 100964 June 04, 2019 June 03, 2020 R&S Power meter ML2495A 1014008 May 13, 2019 May 12, 2020 Anritsu Power sensor MA2411B 0917122 May 13, 2019 May 12, 2020 Anritsu Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in 966 Chamber No. 3. 3. Loop antenna was used for all emissions below 30 MHz. 4. Tested Date: Aug. 30 to Sep. 02, 2019 Report No.: RF181120C09D-2 Page No. 15 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.1.3 Test Procedures For Radiated emission below 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency below 30MHz. For Radiated emission above 30MHz a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detects function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98%) or 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. Report No.: RF181120C09D-2 Page No. 16 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.1.4 Deviation from Test Standard No deviation. 4.1.5 Test Setup For Radiated emission below 30MHz 1m EUT& 3m Support Units Turn Table 80cm Ground Plane Test Receiver For Radiated emission 30MHz to 1GHz Ant. Tower 1-4m Variable 3m 10m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver Report No.: RF181120C09D-2 Page No. 17 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

For Radiated emission above 1GHz Ant. Tower 1-4m Variable EUT& 3m Support Units Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions a. Placed the EUT on the testing table. b. Controlling software (HyperTerminal paste BB8 BLE SOP.doc command) has been activated to set the EUT on specific status. Report No.: RF181120C09D-2 Page No. 18 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.1.7 Test Results BT-LE 1M Above 1GHz Data: CHANNEL TX Channel 0 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 55.4 PK 74.0 -18.6 2.18 H 128 57.4 -2.0 2 2390.00 43.6 AV 54.0 -10.4 2.18 H 128 45.6 -2.0 3 *2402.00 94.4 PK 2.18 H 128 96.4 -2.0 4 *2402.00 92.7 AV 2.18 H 128 94.7 -2.0 5 4804.00 41.4 PK 74.0 -32.6 2.04 H 123 39.1 2.3 6 4804.00 31.5 AV 54.0 -22.5 2.04 H 123 29.2 2.3 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 55.2 PK 74.0 -18.8 1.73 V 148 57.2 -2.0 2 2390.00 43.4 AV 54.0 -10.6 1.73 V 148 45.4 -2.0 3 *2402.00 99.3 PK 1.73 V 148 101.3 -2.0 4 *2402.00 97.8 AV 1.73 V 148 99.8 -2.0 5 4804.00 43.0 PK 74.0 -31.0 1.05 V 203 40.7 2.3 6 4804.00 34.4 AV 54.0 -19.6 1.05 V 203 32.1 2.3 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. Margin value = Emission Level – Limit value 4. The other emission levels were very low against the limit. 5. " * ": Fundamental frequency. Report No.: RF181120C09D-2 Page No. 19 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

CHANNEL TX Channel 19 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 54.7 PK 74.0 -19.3 2.04 H 134 56.7 -2.0 2 2390.00 43.5 AV 54.0 -10.5 2.04 H 134 45.5 -2.0 3 *2440.00 92.4 PK 2.04 H 134 94.5 -2.1 4 *2440.00 90.1 AV 2.04 H 134 92.2 -2.1 5 2483.50 54.3 PK 74.0 -19.7 2.04 H 134 56.5 -2.2 6 2483.50 42.6 AV 54.0 -11.4 2.04 H 134 44.8 -2.2 7 4880.00 40.9 PK 74.0 -33.1 1.98 H 153 38.6 2.3 8 4880.00 31.0 AV 54.0 -23.0 1.98 H 153 28.7 2.3 9 7320.00 44.5 PK 74.0 -29.5 1.48 H 154 36.3 8.2 10 7320.00 33.6 AV 54.0 -20.4 1.48 H 154 25.4 8.2 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 55.1 PK 74.0 -18.9 1.48 V 149 57.1 -2.0 2 2390.00 43.3 AV 54.0 -10.7 1.48 V 149 45.3 -2.0 3 *2440.00 97.9 PK 1.48 V 149 100.0 -2.1 4 *2440.00 96.4 AV 1.48 V 149 98.5 -2.1 5 2483.50 54.2 PK 74.0 -19.8 1.48 V 149 56.4 -2.2 6 2483.50 43.0 AV 54.0 -11.0 1.48 V 149 45.2 -2.2 7 4880.00 41.3 PK 74.0 -32.7 1.53 V 212 39.0 2.3 8 4880.00 33.0 AV 54.0 -21.0 1.53 V 212 30.7 2.3 9 7320.00 44.4 PK 74.0 -29.6 1.87 V 192 36.2 8.2 10 7320.00 35.3 AV 54.0 -18.7 1.87 V 192 27.1 8.2 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. Margin value = Emission Level – Limit value 4. The other emission levels were very low against the limit. 5. " * ": Fundamental frequency. Report No.: RF181120C09D-2 Page No. 20 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

CHANNEL TX Channel 39 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2480.00 91.3 PK 2.15 H 134 93.5 -2.2 2 *2480.00 89.4 AV 2.15 H 134 91.6 -2.2 3 2483.50 54.8 PK 74.0 -19.2 2.15 H 134 57.0 -2.2 4 2483.50 42.3 AV 54.0 -11.7 2.15 H 134 44.5 -2.2 5 4960.00 41.2 PK 74.0 -32.8 2.20 H 135 38.7 2.5 6 4960.00 32.9 AV 54.0 -21.1 2.20 H 135 30.4 2.5 7 7440.00 44.8 PK 74.0 -29.2 1.53 H 142 36.4 8.4 8 7440.00 33.4 AV 54.0 -20.6 1.53 H 142 25.0 8.4 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2480.00 97.8 PK 2.31 V 140 100.0 -2.2 2 *2480.00 96.3 AV 2.31 V 140 98.5 -2.2 3 2483.50 54.1 PK 74.0 -19.9 2.31 V 140 56.3 -2.2 4 2483.50 43.1 AV 54.0 -10.9 2.31 V 140 45.3 -2.2 5 4960.00 42.7 PK 74.0 -31.3 1.19 V 199 40.2 2.5 6 4960.00 34.6 AV 54.0 -19.4 1.19 V 199 32.1 2.5 7 7440.00 44.3 PK 74.0 -29.7 1.33 V 186 35.9 8.4 8 7440.00 34.2 AV 54.0 -19.8 1.33 V 186 25.8 8.4 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF181120C09D-2 Page No. 21 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

Below 1GHz Data: CHANNEL TX Channel 0 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 9kHz ~ 1GHz FUNCTION ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 49.96 30.0 QP 40.0 -10.0 1.00 H 46 38.6 -8.6 2 128.65 25.4 QP 43.5 -18.1 3.00 H 210 34.8 -9.4 3 193.69 24.7 QP 43.5 -18.8 1.00 H 360 34.7 -10.0 4 326.43 26.7 QP 46.0 -19.3 1.00 H 43 32.3 -5.6 5 466.89 29.2 QP 46.0 -16.8 2.00 H 360 31.6 -2.4 6 616.27 31.7 QP 46.0 -14.3 1.00 H 360 30.5 1.2 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. Margin value = Emission Level – Limit value 4. The other emission levels were very low against the limit of frequency range 30MHz~1000MHz. 5. The emission levels were very low against the limit of frequency range 9kHz~30MHz: the amplitude of spurious emissions attenuated more than 20 dB below the permissible value to be report. Report No.: RF181120C09D-2 Page No. 22 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

CHANNEL TX Channel 0 DETECTOR Quasi-Peak (QP) FREQUENCY RANGE 9kHz ~ 1GHz FUNCTION ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 39.82 30.1 QP 40.0 -9.9 1.00 V 360 39.4 -9.3 2 62.98 27.4 QP 40.0 -12.6 1.50 V 360 36.3 -8.9 3 139.22 26.4 QP 43.5 -17.1 1.00 V 160 34.7 -8.3 4 267.67 25.0 QP 46.0 -21.0 1.00 V 133 32.6 -7.6 5 471.03 29.7 QP 46.0 -16.3 1.50 V 86 32.0 -2.3 6 621.12 32.8 QP 46.0 -13.2 1.50 V 101 31.5 1.3 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. Margin value = Emission Level – Limit value 4. The other emission levels were very low against the limit of frequency range 30MHz~1000MHz. 5. The emission levels were very low against the limit of frequency range 9kHz~30MHz: the amplitude of spurious emissions attenuated more than 20 dB below the permissible value to be report. Report No.: RF181120C09D-2 Page No. 23 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

BT-LE 2M Above 1GHz Data: CHANNEL TX Channel 0 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 53.8 PK 74.0 -20.2 2.77 H 103 55.8 -2.0 2 2390.00 44.1 AV 54.0 -9.9 2.77 H 103 46.1 -2.0 3 *2402.00 92.2 PK 2.77 H 103 94.2 -2.0 4 *2402.00 88.4 AV 2.77 H 103 90.4 -2.0 5 4804.00 43.4 PK 74.0 -30.6 2.05 H 220 41.1 2.3 6 4804.00 34.4 AV 54.0 -19.6 2.05 H 220 32.1 2.3 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 54.4 PK 74.0 -19.6 1.94 V 158 56.4 -2.0 2 2390.00 44.3 AV 54.0 -9.7 1.94 V 158 46.3 -2.0 3 *2402.00 99.7 PK 1.94 V 158 101.7 -2.0 4 *2402.00 96.9 AV 1.94 V 158 98.9 -2.0 5 4804.00 43.6 PK 74.0 -30.4 1.85 V 212 41.3 2.3 6 4804.00 35.3 AV 54.0 -18.7 1.85 V 212 33.0 2.3 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. Margin value = Emission Level – Limit value 4. The other emission levels were very low against the limit. 5. " * ": Fundamental frequency. Report No.: RF181120C09D-2 Page No. 24 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

CHANNEL TX Channel 19 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 55.4 PK 74.0 -18.6 2.86 H 95 57.4 -2.0 2 2390.00 44.1 AV 54.0 -9.9 2.86 H 95 46.1 -2.0 3 *2440.00 91.7 PK 2.86 H 95 93.8 -2.1 4 *2440.00 87.8 AV 2.86 H 95 89.9 -2.1 5 2483.50 54.3 PK 74.0 -19.7 2.86 H 95 56.5 -2.2 6 2483.50 43.6 AV 54.0 -10.4 2.86 H 95 45.8 -2.2 7 4880.00 43.0 PK 74.0 -31.0 2.16 H 197 40.7 2.3 8 4880.00 34.1 AV 54.0 -19.9 2.16 H 197 31.8 2.3 9 7320.00 43.3 PK 74.0 -30.7 1.80 H 166 35.1 8.2 10 7320.00 33.3 AV 54.0 -20.7 1.80 H 166 25.1 8.2 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 2390.00 56.3 PK 74.0 -17.7 2.47 V 148 58.3 -2.0 2 2390.00 44.2 AV 54.0 -9.8 2.47 V 148 46.2 -2.0 3 *2440.00 99.3 PK 2.47 V 148 101.4 -2.1 4 *2440.00 96.4 AV 2.47 V 148 98.5 -2.1 5 2483.50 54.9 PK 74.0 -19.1 2.47 V 148 57.1 -2.2 6 2483.50 43.6 AV 54.0 -10.4 2.47 V 148 45.8 -2.2 7 4880.00 43.4 PK 74.0 -30.6 1.62 V 188 41.1 2.3 8 4880.00 35.1 AV 54.0 -18.9 1.62 V 188 32.8 2.3 9 7320.00 44.0 PK 74.0 -30.0 1.50 V 173 35.8 8.2 10 7320.00 34.1 AV 54.0 -19.9 1.50 V 173 25.9 8.2 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. Margin value = Emission Level – Limit value 4. The other emission levels were very low against the limit. 5. " * ": Fundamental frequency. Report No.: RF181120C09D-2 Page No. 25 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

CHANNEL TX Channel 39 DETECTOR Peak (PK) FREQUENCY RANGE 1GHz ~ 25GHz FUNCTION Average (AV) ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2480.00 89.4 PK 2.89 H 88 91.6 -2.2 2 *2480.00 85.1 AV 2.89 H 88 87.3 -2.2 3 2483.50 54.9 PK 74.0 -19.1 2.89 H 88 57.1 -2.2 4 2483.50 44.3 AV 54.0 -9.7 2.89 H 88 46.5 -2.2 5 4960.00 43.2 PK 74.0 -30.8 1.42 H 222 40.7 2.5 6 4960.00 33.3 AV 54.0 -20.7 1.42 H 222 30.8 2.5 7 7440.00 43.1 PK 74.0 -30.9 1.73 H 178 34.7 8.4 8 7440.00 32.8 AV 54.0 -21.2 1.73 H 178 24.4 8.4 ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M EMISSION ANTENNA TABLE RAW CORRECTION FREQ. LIMIT MARGIN NO. LEVEL HEIGHT ANGLE VALUE FACTOR (MHz) (dBuV/m) (dB) (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 *2480.00 97.5 PK 2.29 V 153 99.7 -2.2 2 *2480.00 94.1 AV 2.29 V 153 96.3 -2.2 3 2483.50 54.5 PK 74.0 -19.5 2.29 V 153 56.7 -2.2 4 2483.50 44.6 AV 54.0 -9.4 2.29 V 153 46.8 -2.2 5 4960.00 43.5 PK 74.0 -30.5 1.50 V 202 41.0 2.5 6 4960.00 34.7 AV 54.0 -19.3 1.50 V 202 32.2 2.5 7 7440.00 44.3 PK 74.0 -29.7 1.68 V 186 35.9 8.4 8 7440.00 34.2 AV 54.0 -19.8 1.68 V 186 25.8 8.4 REMARKS: 1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission Level – Limit value 5. " * ": Fundamental frequency. Report No.: RF181120C09D-2 Page No. 26 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 4.2.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver ESCS 30 847124/029 Oct. 24, 2018 Oct. 23, 2019 R&S Line-Impedance Stabilization Network (for ESH3-Z5 848773/004 Oct. 22, 2018 Oct. 21, 2019 EUT) R&S Line-Impedance Stabilization Network ESH3-Z5 835239/001 Mar. 17, 2019 Mar. 16, 2020 (for Peripheral) R&S 50 ohms Terminator N/A 3 Oct. 22, 2018 Oct. 21, 2019 RF Cable 5D-FB COCCAB-001 Sep. 28, 2018 Sep. 27, 2019 Fixed attenuator STI02-2200-10 003 Mar. 14, 2019 Mar. 13, 2020 EMCI Software BVADT_Cond_ NA NA NA BVADT V7.3.7.4 Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Conduction 1. 3. Tested Date: Sep. 02, 2019 Report No.: RF181120C09D-2 Page No. 27 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. 4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT 40cm 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF181120C09D-2 Page No. 28 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.2.7 Test Results Quasi-Peak (QP) / Phase Line (L) Detector Function Average (AV) Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.44297 9.97 26.25 20.59 36.22 30.56 57.01 47.01 -20.79 -16.45 2 1.69922 10.05 12.40 5.56 22.45 15.61 56.00 46.00 -33.55 -30.39 3 8.48047 10.40 13.56 5.70 23.96 16.10 60.00 50.00 -36.04 -33.90 4 9.28125 10.44 18.99 10.54 29.43 20.98 60.00 50.00 -30.57 -29.02 5 10.14453 10.49 20.39 9.06 30.88 19.55 60.00 50.00 -29.12 -30.45 6 14.43359 10.73 20.91 5.55 31.64 16.28 60.00 50.00 -28.36 -33.72 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF181120C09D-2 Page No. 29 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

Quasi-Peak (QP) / Phase Neutral (N) Detector Function Average (AV) Corr. Reading Value Emission Level Limit Margin Freq. No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.44688 9.95 26.44 19.19 36.39 29.14 56.93 46.93 -20.54 -17.79 2 4.59375 10.14 1.74 -4.79 11.88 5.35 56.00 46.00 -44.12 -40.65 3 7.65234 10.27 7.77 1.75 18.04 12.02 60.00 50.00 -41.96 -37.98 4 9.81250 10.36 20.35 10.78 30.71 21.14 60.00 50.00 -29.29 -28.86 5 14.36719 10.55 21.24 5.98 31.79 16.53 60.00 50.00 -28.21 -33.47 6 21.23828 10.81 4.79 0.62 15.60 11.43 60.00 50.00 -44.40 -38.57 Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level – Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF181120C09D-2 Page No. 30 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.3 Conducted Output Power Measurement 4.3.1 Limits of Conducted Output Power Measurement For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30dBm) 4.3.2 Test Setup EUT Power Sensor Power Meter Attenuator 4.3.3 Test Instruments Refer to section 4.1.2 to get information of above instrument. 4.3.4 Test Procedures A peak power sensor was used on the output port of the EUT. A power meter was used to read the response of the peak power sensor. Record the power level. Average power sensor was used to perform output power measurement, trigger and gating function of wide band power meter is enabled to measure max output power of TX on burst. Duty factor is not added to measured value. 4.3.5 Deviation from Test Standard No deviation. 4.3.6 EUT Operating Conditions The software provided by client to enable the EUT under transmission condition continuously at lowest, middle and highest channel frequencies individually. Report No.: RF181120C09D-2 Page No. 31 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

4.3.7 Test Results BT-LE 1M FOR PEAK POWER Frequency Peak Power Peak Power Limit Channel Pass/Fail (MHz) (mW) (dBm) (dBm) 0 2402 2.223 3.47 30 Pass 19 2440 2.042 3.10 30 Pass 39 2480 1.854 2.68 30 Pass FOR AVERAGE POWER Frequency Average Power Average Power Channel (MHz) (mW) (dBm) 0 2402 2.208 3.44 19 2440 2.028 3.07 39 2480 1.837 2.64 BT-LE 2M FOR PEAK POWER Frequency Peak Power Peak Power Limit Channel Pass/Fail (MHz) (mW) (dBm) (dBm) 0 2402 2.218 3.46 30 Pass 19 2440 2.037 3.09 30 Pass 39 2480 1.849 2.67 30 Pass FOR AVERAGE POWER Frequency Average Power Average Power Channel (MHz) (mW) (dBm) 0 2402 2.198 3.42 19 2440 2.023 3.06 39 2480 1.832 2.63 Report No.: RF181120C09D-2 Page No. 32 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF181120C09D-2 Page No. 33 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01

Appendix – Information of the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Lin Kou EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF181120C09D-2 Page No. 34 / 34 Report Format Version: 6.1.1 Reference No.: 190329E01


Document Created: 2019-10-17 02:36:05
Document Modified: 2019-10-17 02:36:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC