MDE_ECOM_1203_FCCc Final part 27 Test report

FCC ID: XAM300011GR02

Test Report

Download: PDF
FCCID_2121077

Final Report on Ci70A FCC ID:XAM300011GR02 IC:8311A-300011GR02 Report Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Date: September 02, 2013 Test Laboratory: 7Layers AG Borsigstr. 11 40880 Ratingen Germany Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the test laboratory. 7Layers AG Aufsichtsratsvorsitzender Registergericht registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Ralf Mertens USt-IdNr  VAT No.: Phone: +49 (0) 2102 749 0 Vorstand Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. H.-J. Meckelburg TAX No. 147/5869/0385 www.7Layers.com

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 1 Administrative Data 1.1 Project Data Project Responsible: Imad Hjije Date Of Test Report: 2013/09/02 Date of first test: 2013/07/22 Date of last test: 2013/07/22 1.2 Applicant Data Company Name: ecom instruments GmbH Street: Industriestraße 2 City: 97959 Assamstadt Country: Germany Contact Person: Mr. Harald Fiederlein Phone: +49 (0) 6294 4224 973 Fax: +49 (0) 6294 4224 600 E-Mail: Harald.Fiederlein@ecom-ex.com 1.3 Test Laboratory Data The following list shows all places and laboratories involved for test result generation: 7 layers DE Company Name : 7 layers AG Street : Borsigstrasse 11 City : 40880 Ratingen Country : Germany Contact Person : Mr. Michael Albert Phone : +49 2102 749 201 Fax : +49 2102 749 444 E Mail : michael.albert@7Layers.de Laboratory Details Lab ID Identification Responsible Accreditation Info Lab 1 Radiated Emissions Mr. Robert Machulec DAkkS-Registration no. D-PL-12140-01-01 Mr. Andreas Petz 1.4 Signature of the Testing Responsible Patrick Lomax responsible for tests performed in: Lab 1 Page 2 of 27

layers Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 1.5 Signature of the Accreditation Responsible Qi [o Rerwl Accreditation scope responsible person responsible for Lab 1 2 Test Object Data 2.1 General OUT Description The following section lists all OUTs (Object‘s Under Test) involved during testing. OUT: i.roc Ci70 —Ex Type / Model / Family: C170A FCC ID: XAM300011GRO2 IC:8311A—300011GRO2 Product Category: Handheld Device Manufacturer: Company Name: Please see applicant data Contact Person: Parameter List: Parameter name Value Parameter for Scope FCC_v2: AC Power Supply (via AC/DC Charger) 120 (V) Antenna gain 1700 band 2.0 (dBi) Antenna gain 1900 band 3.2 (dBi) Antenna gain 850 band —1.0 (dBi) highest channel 251 (848.8MHz) for GSM850, 810 (1909.8MHz) for GSM1900, 4233 (846.6MHz) for FDDS, 9538 (1907.6MHz) for FDD2 lowest channel 128 (824.2MHz) for GSM850, 512 (1850.2MHz) for GSM1900, 4132 (826.4MHz) for FDDS, 9262 (1852.4MHz)for FDD2 MHz mid channel (190 ()836‘6MHZ) for GSM850, 661 (1880.0MHz) for GSM1900, 4183 (836.6MHz) for FDDS, 9400 (1880MHz) for FDD2 Powered by Battery 3.7 (V) Page 3 of 26

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 2.2 Detailed Description of OUT Samples Sample : a01 OUT Identifier i.roc Ci70 -Ex Sample Description Standard Sample Serial No. 012775000378490 HW Status P4 SW Status D3200-STSUGN-1575 Nominal Voltage 3.7 V Normal Temp. 25 °C 2.3 OUT Features Features for OUT: i.roc Ci70 -Ex Designation Description Allowed Values Supported Value(s) Features for scope: FCC_v2 CDMA2000 EUT supports CDMA2000 in band 824.7MHz - _BC0 848.3MHz (BC0) CDMA2000 EUT supports CDMA2000 in band 1851.25MHz - _BC1 1908.75MHz (BC1) CDMA2000 EUT supports CDMA2000 EV-DO in band _EV- 824.7MHz - 848.3MHz (BC0) DO_BC0 CDMA2000 EUT supports CDMA2000 EV-DO in band _EV- 1851.25MHz - 1908.75MHz (BC1) DO_BC1 EDGE850 EUT supports EDGE in the band 824 MHz - 849 MHz EDGE1900 EUT supports EDGE in the band 1850 MHz - 1910 MHz FDD2 EUT supports UMTS FDD2 in the band 1850 MHz - 1910 MHz FDD5 EUT supports UMTS FDD5 in the band 824 MHz - 849 MHz GSM850 EUT supports GSM850 band 824MHz - 849MHz HSDPA- EUT supports UMTS FDD2 HSDPA in the band FDD2 1850 MHz - 1910 MHz HSDPA- EUT supports UMTS FDD5 HSDPA in the band FDD5 824 MHz - 849 MHz HSUPA- EUT supports UMTS FDD2 HSUPA in the band FDD2 1850 MHz - 1910 MHz HSUPA- EUT supports UMTS FDD5 HSUPA in the band FDD5 824 MHz - 849 MHz Iant Integral Antenna: permanent fixed antenna, which may be built-in, designed as an indispensable part of the equipment PCS1900 EUT supports PCS1900 band 1850MHz - 1910MHz TantC temporary antenna connector, which may be only built-in for testing, designed as an example part of the equipment Page 4 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 2.4 Setups used for Testing For each setup a relation is given to determine if and which samples and auxiliary equipment is used. The left side list all OUT samples and the right side lists all auxiliary equipment for the given setup. Setup No. List of OUT samples List of auxiliary equipment Sample No. Sample Description AE No. AE Description A01_rad (sample #01 (radiated setup)) Sample: a01 Standard Sample 3 Results 3.1 General Documentation of tested Available at the test laboratory. devices: Interpretation of the The results of the inspection are described on the following test results: pages, where 'Conformity' or 'Passed' means that the certification criteria were verified and that the tested device is conform to the applied standard. In cases where 'Declaration' is printed, the required documents are available in the manufacturers product documentation. In cases where 'not applicable' is printed, the test case requirements are not relevant to the specific equipment implementation. Note: 1. The laboratory environmental conditions are recorded and available in the Interlab system for each performed test. 2. This product is a variant of a previously tested and certified product (FCC ID:XAM300011GR01). The only change to the product is the inclusion of a PCI WWAN module from Seirra Wireless (FCC ID: N7NMC8355). For this reason, only partial testing was performed. 3.2 List of the Applicable Body (Body for Scope: FCC_v2) Designation Description FCC47CFRChIPART27MISCELLANEOUS Part 27, Subpart C - Technical Standards WIRELESS COMMUNICATIONS SERVICES 3.3 List of Test Specification Test Specification: FCC part 2 and 27 Version 10-1-11 Edition Title: PART 2 - GENERAL RULES AND REGULATIONS PART 27 - MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Page 5 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 3.4 Summary Test Case Identifier / Name Lab Test (condition) Result Date of Test Ref. Setup 27.4 Field strength of spurious radiation §2.1053, §27.53 27.4; Frequency Band = FDD4, Mode = Passed 2013/07/22 Lab 1 A01_rad HSDPA, Channel = 1412, Frequency = 1732.4MHz 27.4; Frequency Band = FDD4, Mode = Passed 2013/07/22 Lab 1 A01_rad HSUPA, Channel = 1412, Frequency = 1732.4MHz 27.4; Frequency Band = FDD4, Mode = W- Passed 2013/07/22 Lab 1 A01_rad CDMA, Channel = 1412, Frequency = 1732.4MHz Page 6 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 3.5 Detailed Results 3.5.1 27.4 Field strength of spurious radiation §2.1053, §27.53 Test: 27.4; Frequency Band = FDD4, Mode = HSDPA, Channel = 1412, Frequency = 1732.4MHz Result: Passed Setup No.: A01_rad Date of Test: 2013/07/22 17:06 Body: FCC47CFRChIPART27MISCELLANEOUS WIRELESS COMMUNICATIONS SERVI Test Specification: FCC part 2 and 27 Detailed Results: resolution frequency peak value margin to antenna EUT detector trace bandwidth limit /dBm azimuth /° verdict /MHz /dBm limit /dB polarization orientation /kHz peak maxhold 1000 2132.5 -23.49 -13.00 10.49 0.0 vertical vertical passed peak maxhold 1000 2134.4 -27.64 -13.00 14.64 90.0 vertical vertical passed peak maxhold 1000 18653.3 -26.01 -13.00 13.01 -180.0 vertical vertical passed peak maxhold 1000 19214.4 -24.02 -13.00 11.02 -120.0 vertical horizontal passed peak maxhold 1000 19228.5 -23.98 -13.00 10.98 120.0 horizontal horizontal passed peak maxhold 1000 19312.6 -24.26 -13.00 11.26 -90.0 vertical vertical passed peak maxhold 1000 19326.7 -22.51 -13.00 9.51 45.0 vertical vertical passed no further values have been found with a margin of less than 20 dB Page 7 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Test: 27.4; Frequency Band = FDD4, Mode = HSUPA, Channel = 1412, Frequency = 1732.4MHz Result: Passed Setup No.: A01_rad Date of Test: 2013/07/22 15:51 Body: FCC47CFRChIPART27MISCELLANEOUS WIRELESS COMMUNICATIONS SERVI Test Specification: FCC part 2 and 27 Detailed Results: resolution frequency peak value margin to antenna EUT detector trace bandwidth limit /dBm azimuth /° verdict /MHz /dBm limit /dB polarization orientation /kHz peak maxhold 1000 1694.8 -32.90 -13.00 19.90 60.0 horizontal horizontal passed peak maxhold 1000 1701.9 -32.98 -13.00 19.98 60.0 horizontal horizontal passed peak maxhold 1000 1703.3 -32.49 -13.00 19.49 0.0 horizontal horizontal passed peak maxhold 1000 1707.6 -31.61 -13.00 18.61 60.0 horizontal horizontal passed peak maxhold 1000 18653.3 -25.65 -13.00 12.65 -90.0 vertical vertical passed peak maxhold 1000 19214.4 -24.23 -13.00 11.23 -45.0 horizontal vertical passed peak maxhold 1000 19312.6 -23.88 -13.00 10.88 -120.0 vertical horizontal passed peak maxhold 1000 19326.7 -23.17 -13.00 10.17 -120.0 horizontal horizontal passed peak maxhold 1000 19340.7 -24.55 -13.00 11.55 90.0 horizontal vertical passed no further values have been found with a margin of less than 20 dB Test: 27.4; Frequency Band = FDD4, Mode = W-CDMA, Channel = 1412, Frequency = 1732.4MHz Result: Passed Setup No.: A01_rad Date of Test: 2013/07/22 18:27 Body: FCC47CFRChIPART27MISCELLANEOUS WIRELESS COMMUNICATIONS SERVI Test Specification: FCC part 2 and 27 Page 8 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Detailed Results: resolution frequency peak value margin to antenna EUT detector trace bandwidth limit /dBm azimuth /° verdict /MHz /dBm limit /dB polarization orientation /kHz peak maxhold 1000 18653.3 -25.63 -13.00 12.63 60.0 vertical horizontal passed peak maxhold 1000 19214.4 -24.36 -13.00 11.36 -135.0 horizontal vertical passed peak maxhold 1000 19312.6 -24.83 -13.00 11.83 -60.0 vertical horizontal passed peak maxhold 1000 19326.7 -23.60 -13.00 10.60 -135.0 vertical vertical passed peak maxhold 1000 19340.7 -24.50 -13.00 11.50 -120.0 horizontal horizontal passed no further values have been found with a margin of less than 20 dB Page 9 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 4 Test Equipment Details 4.1 List of Used Test Equipment The calibration, hardware and software states are shown for the testing period. Test Equipment Anechoic Chamber Lab ID: Lab 1 Manufacturer: Frankonia Description: Anechoic Chamber for radiated testing Type: 10.58x6.38x6.00 m³ Calibration Details Last Execution Next Exec. NSA (FCC, IC) 2011/01/10 2014/01/10 Single Devices for Anechoic Chamber Single Device Name Type Serial Number Manufacturer Air compressor none - Atlas Copco Anechoic Chamber 10.58 x 6.38 x 6.00 m³ none Frankonia Calibration Details Last Execution Next Exec. FCC listing 96716 3m Part15/18 2011/01/11 2014/01/10 IC listing 3699A-1 3m 2011/02/07 2014/02/06 Controller Maturo MCU 961208 Maturo GmbH EMC camera CE-CAM/1 - CE-SYS EMC camera Nr.2 CCD-400E 0005033 Mitsubishi Filter ISDN B84312-C110-E1 Siemens&Matsushita Filter Universal 1A BB4312-C30-H3 - Siemens&Matsushita Page 10 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Test Equipment Auxiliary Equipment for Radiated emissions Lab ID: Lab 1 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Auxiliary Equipment for Radiated emissions Single Device Name Type Serial Number Manufacturer Antenna mast AM 4.0 AM4.0/180/11920 Maturo GmbH 513 Biconical Broadband SBA 9119 9119-005 Schwarzbeck Antenna Calibration Details Last Execution Next Exec. Standard Calibration 2009/06/04 2014/06/03 Biconical dipole VUBA 9117 9117-108 Schwarzbeck Calibration Details Last Execution Next Exec. Standard Calibration 2008/10/27 2013/10/26 Standard Calibration 2012/01/18 2015/01/17 Broadband Amplifier JS4-18002600-32-5P 849785 Miteq 18MHz-26GHz Broadband Amplifier AFS4-01000400-1Q-10P-4 - Miteq 1GHz-4GHz Broadband Amplifier JS4-00101800-35-5P 896037 Miteq 30MHz-18GHz Cable "ESI to EMI EcoFlex10 W18.01- Kabel Kusch Antenna" 2+W38.01-2 Cable "ESI to Horn UFB311A+UFB293C W18.02- Rosenberger Micro-Coax Antenna" 2+W38.02-2 Double-ridged horn HF 906 357357/001 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/05/18 2015/05/17 Double-ridged horn HF 906 357357/002 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/06/26 2015/06/25 High Pass Filter 4HC1600/12750-1.5-KK 9942011 Trilithic High Pass Filter 5HC2700/12750-1.5-KK 9942012 Trilithic High Pass Filter 5HC3500/12750-1.2-KK 200035008 Trilithic High Pass Filter WHKX 7.0/18G-8SS 09 Wainwright Horn Antenna BBHA 9170 Schwarzbeck 15-26 GHz BBHA 9170 Log.-per. Antenna HL 562 Ultralog 100609 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2012/12/18 2015/12/17 Log.-per. Antenna HL 562 Ultralog 830547/003 Rohde & Schwarz GmbH & Co. KG Loop Antenna HFH2-Z2 829324/006 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/10/27 2014/10/26 Page 11 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Single Devices for Auxiliary Equipment for Radiated emissions (continued) Single Device Name Type Serial Number Manufacturer Pyramidal Horn 3160-09 00083069 EMCO Elektronik GmbH Antenna 26,5 GHz Pyramidal Horn 3160-10 00086675 EMCO Elektronik GmbH Antenna 40 GHz Tilt device Maturo Antrieb TD1.5-10kg TD1.5- Maturo GmbH (Rohacell) 10kg/024/379070 9 Test Equipment Auxiliary Test Equipment Lab ID: Lab 1 Manufacturer: see single devices Description: Single Devices for various Test Equipment Type: various Serial Number: none Single Devices for Auxiliary Test Equipment Single Device Name Type Serial Number Manufacturer Broadband Power 1506A / 93459 LM390 Weinschel Associates Divider N (Aux) Broadband Power WA1515 A855 Weinschel Associates Divider SMA Digital Multimeter 03 Fluke 177 86670383 Fluke Europe B.V. (Multimeter) Calibration Details Last Execution Next Exec. Customized calibration 2011/10/19 2013/10/18 Fibre optic link FO RS232 Link 181-018 Pontis Satellite (Aux) Fibre optic link FO RS232 Link 182-018 Pontis Transceiver (Aux) Isolating Transformer LTS 604 1888 Thalheimer Transformatorenwerke GmbH Notch Filter Ultra WRCA800/960-6EEK 24 Wainwright Stable (Aux) Spectrum Analyser FSP3 836722/011 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard 2012/06/13 2015/06/12 Vector Signal SMIQ 03B 832492/061 Rohde & Schwarz GmbH & Generator Co.KG Page 12 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Test Equipment Digital Signalling Devices Lab ID: Lab 1 Description: Signalling equipment for various wireless technologies. Single Devices for Digital Signalling Devices Single Device Name Type Serial Number Manufacturer Bluetooth Signalling CBT 100589 Rohde & Schwarz GmbH & Unit CBT Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/24 2014/11/23 CMW500 CMW500 107500 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Initial factory calibration 2012/01/26 2014/01/25 Digital Radio CMD 55 831050/020 Rohde & Schwarz GmbH & Communication Tester Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/11/28 2014/11/27 Universal Radio CMU 200 102366 Rohde & Schwarz GmbH & Communication Tester Co. KG HW/SW Status Date of Start Date of End Hardware: 2007/07/16 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B56V14, B68 3v04, PCMCIA, U65V04 Software: K21 4v21, K22 4v21, K23 4v21, K24 4v21, K42 4v21, K43 4v21, K53 4v21, K56 4v22, K57 4v22, K58 4v22, K59 4v22, K61 4v22, K62 4v22, K63 4v22, K64 4v22, K65 4v22, K66 4v22, K67 4v22, K68 4v22, K69 4v22 Firmware: µP1 8v50 02.05.06 --- Universal Radio CMU 200 837983/052 Rohde & Schwarz GmbH & Communication Tester Co. KG Calibration Details Last Execution Next Exec. Standard calibration 2011/12/07 2014/12/06 HW/SW Status Date of Start Date of End HW options: 2007/01/02 B11, B21V14, B21-2, B41, B52V14, B52-2, B53-2, B54V14, B56V14, B68 3v04, B95, PCMCIA, U65V02 SW options: K21 4v11, K22 4v11, K23 4v11, K24 4v11, K27 4v10, K28 4v10, K42 4v11, K43 4v11, K53 4v10, K65 4v10, K66 4v10, K68 4v10, Firmware: µP1 8v40 01.12.05 --- SW: 2008/11/03 K62, K69 Vector Signal SMU200A 100912 Rohde & Schwarz GmbH & Generator Co. KG Page 13 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Test Equipment Emission measurement devices Lab ID: Lab 1 Description: Equipment for emission measurements Serial Number: see single devices Single Devices for Emission measurement devices Single Device Name Type Serial Number Manufacturer Personal Computer Dell 30304832059 Dell Power Meter NRVD 828110/016 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2013/05/03 2014/05/02 Sensor Head A NRV-Z1 827753/005 Rohde & Schwarz GmbH & Co.KG Calibration Details Last Execution Next Exec. Standard calibration 2013/04/30 2014/04/29 Signal Generator SMR 20 846834/008 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. standard calibration 2011/05/12 2014/05/11 Spectrum Analyzer ESIB 26 830482/004 Rohde & Schwarz GmbH & Co. KG Calibration Details Last Execution Next Exec. Standard Calibration 2011/12/05 2013/12/04 HW/SW Status Date of Start Date of End Firmware-Update 4.34.4 from 3.45 during calibration 2009/12/03 Page 14 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 5 Annex 5.1 Additional Information for Report Page 15 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Summary of Test Results _____________________ _____________________ The EUT complied with all performed tests as listed in the summary section of this report. __________________________________________________________________________ Technical Report Summary ______________________ ______________________ Type of Authorization : Certification for a GSM cellular radiotelephone device Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 0 to 69. The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification § 2.1046 Measurement required: RF power output § 2.1049 Measurement required: Occupied bandwidth § 2.1051 Measurement required: Spurious emissions at antenna terminals § 2.1053 Measurement required: Field strength of spurious radiation § 2.1055 Measurement required: Frequency stability § 2.1057 Frequency spectrum to be investigated Part 27, Subpart C—Technical Standards § 27.50 Power and antenna height limits § 27.53 Emissions limits § 27.54 Frequency stability additional documents ANSI TIA-603-C-2004 Description of Methods of Measurements ___________________________________ ___________________________________ ______________ RF Power Output ______________ Standard FCC Part 27, Subpart C The test was performed according to: FCC §2.1046 Test Description (conducted measurement procedure) Page 16 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 1) The EUT was coupled to a Spectrum Analyser and a Digital Communication Tester through a Power Divider. Refer to chapter "Setup Drawings". 2) The total insertion losses for signal path 1 and signal path 2 were measured. The values were used to correct the readings from the Spectrum Analyser and the Digital Communication Tester. 3) A call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Important Settings: - Channel (Frequency): please refer to the detailed results 4) The transmitted power of the EUT was recorded by using a spectrum analyser. Test Description (radiated measurement procedure) 1) The EUT was placed inside an anechoic chamber. Refer to chapter "Setup Drawings". The EUT was coupled to a Digital Communication Tester which was located outside the chamber via a small signalling antenna. 2) A call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Important Settings: - Output Power: Maximum - Channel: please refer to the detailed results 3) A substitution procedure is used so that the readings from the spectrum analyser are corrected and represent directly the equivalent radiated power (related to a lamda/2 dipole). 4) The output power was measured in both vertical and horizontal antenna polarisation during the call is established on the lowest channel, mid channel and on the highest channel. To find the worst case power all orientations (X, Y, Z) of the EUT have been measured. 5) The test procedure according to TIA-603-C-2004 has been considered. Test Requirements / Limits §2.1046 Measurements Required: RF Power Output (a) For transmitters other than single sideband, independent sideband and controlled carrier radiotelephone, power output shall be measured at the RF output terminals when the transmitter is adjusted in accordance with the tune-up procedure to give the values of current and voltage on the circuit elements specified in § 2.1033(c)(8). The electrical characteristics of the output terminals when this test is made shall be stated. §27.50 Power and antenna height limits. (d) The following power and antenna height requirements apply to stations transmitting in the 1710–1755 MHz and 2110–2155 MHz bands: (2) Fixed, mobile, and portable (hand-held) stations operating in the 1710–1755 MHz band are limited to a peak EIRP of 1 watt. Fixed stations operating in this band are limited to a maximum antenna height of 10 meters above ground, and mobile and portable stations must employ a means for limiting power to the minimum necessary for successful communications. ____________________________ Emission and Occupied Bandwidth ____________________________ Standard FCC Part 27, Subpart C The test was performed according to: FCC §2.1049 Test Description 1) The EUT was coupled to a Spectrum Analyser and a Digital Communication Tester through a Power Divider. Refer to chapter "Setup Drawings". 2) The total insertion losses for signal path 1 and signal path 2 were measured. The values were used to correct the readings from the Spectrum Analyser and the Digital Communication Tester. 3) A call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Important Settings: - Output Power: Maximum - Channel: please refer to the detailed results 4) Important Analyser Settings: - Resolution Bandwidth: >1% of the manufacturer’s stated occupied bandwidth 5) The maximum spectral level of the modulated signal was recorded as the reference. 6) The emission bandwidth is measured as follows: the two furthest frequencies above and below the frequency of the maximum reference level where the spectrum is –26 dB down have to be found. 7) The occupied bandwidth (99% Bandwidth) is measured as follows: Page 17 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 the occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers are each equal to 0.5 percent of the total mean power. Test Requirements / Limits § 2.1049 Measurements required: Occupied bandwidth The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured under the following conditions (as applicable): (h) Transmitters employing digital modulation techniques - when modulated by an input signal such that its amplitude and symbol rate represent the maximum rated conditions under which the equipment will be operated. The signal shall be applied through any filter networks, pseudo-random generators or other devices required in normal service. Additionally, the occupied bandwidth shall be shown for operation with any devices used for modifying the spectrum when such devices are optional at the discretion of the user. _________________________________ Spurious emissions at antenna terminals _________________________________ Standard FCC Part 27, Subpart C The test was performed according to FCC §2.1051 Test Description 1) The EUT was coupled to a Spectrum Analyser and a Digital Communication Tester through a Power Divider. Refer to chapter "Setup Drawings". 2) The total insertion losses for signal path 1 and signal path 2 were measured. The values were used to correct the readings from the Spectrum Analyser and the Digital Communication Tester. 3) A call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Important Settings: - Output Power: Maximum - Channel: please refer to the detailed results 4) Important Analyser Settings - [Resolution Bandwidth]: a) [>=1% of wanted signal bandwidth] in the Span of 1 MHz directly below and above the Band, b) otherwise [1 MHz] c) [reduced resolution bandwidth] in case the curve of the analyser IF-Filter or the wanted EUT signal leads to an exceeding of the limit, in this case a correction factor was used - Sweep Time: depending on the transmitting signal, the span and the resolution bandwidth 5) The spurious emissions peaks were measured in the frequency range from 9 kHz to 18 GHz (up to the 10th harmonic) during the call is established Test Requirements / Limits § 2.1051 Spurious emissions at antenna terminals The radio frequency voltage or power generated within the equipment and appearing on a spurious frequency shall be checked at the equipment output terminals when properly loaded with a suitable artificial antenna. Curves or equivalent data shall show the magnitude of each harmonic and other spurious emission that can be detected when the equipment is operated under the conditions specified in Sec. 2.1049 as appropriate. The magnitude of spurious emissions which are attenuated more than 20 dB below the permissible value need not be specified. § 2.1057 Frequency spectrum to be investigated. (a) In all of the measurements set forth in Secs. 2.1051 and 2.1053, the spectrum shall be investigated from the lowest radio frequency signal generated in the equipment, without going below 9 kHz, up to at least the frequency shown below: (1) If the equipment operates below 10 GHz: to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. (b) Particular attention should be paid to harmonics and subharmonics of the carrier frequency as well as to those frequencies removed from the carrier by multiples of the oscillator frequency. Radiation at the Page 18 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 frequencies of multiplier stages should also be checked. (c) The amplitude of spurious emissions which are attenuated more than 20 dB below the permissible value need not be reported. (d) Unless otherwise specified, measurements above 40 GHz shall be performed using a minimum resolution bandwidth of 1 MHz. § 27.53 Emission limits (h) For operations in the 1710–1755 MHz and 2110–2155 MHz bands, the power of any emission outside a licensee's frequency block shall be attenuated below the transmitter power (P) by at least 43 + 10 log10(P) dB. Remark of the test laboratory: This is calculated to be -13 dBm. (1) Compliance with this provision is based on the use of measurement instrumentation employing a resolution bandwidth of 1 megahertz or greater. However, in the 1 megahertz bands immediately outside and adjacent to the licensee's frequency block, a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. (2) When measuring the emission limits, the nominal carrier frequency shall be adjusted as close to the licensee's frequency block edges, both upper and lower, as the design permits. (3) The measurements of emission power can be expressed in peak or average values, provided they are expressed in the same parameters as the transmitter power. For reporting only spurious emission levels reaching to the 20dB margin to limit were noted. _______________________________ Field strength of spurious radiation _______________________________ Standard FCC Part 27, Subpart C The test was performed according to: FCC §2.1053 Test Description 1) The EUT was placed inside an anechoic chamber. Refer to chapter "Setup Drawings". The EUT was coupled to a Digital Communication Tester which was located outside the chamber via a small signalling antenna. 2) A call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Important Settings: - Output Power: Maximum - Channel : please refer to the detailed results 3) A pre-calibration procedure is used so that the readings from the spectrum analyser are corrected and represent directly the equivalent radiated power (related to a lamda/2 dipole). 4) All spurious radiation measurements were made with spectrum analyser and the appropriate calibrated antennas for the frequency range of 30 MHz to 18 GHz (up to the 10th harmonic of the transmit frequency). The frequency range from 9 kHz to 30 MHz has been examined during the conducted spurious emission measurements. 5) Important Analyser Settings - [Resolution Bandwidth / Video Bandwidth]: a) [3 kHz / 10 kHz] in the Span of 1 MHz directly below and above the Band, b) [10 kHz / 30 kHz] in case the curve of the analyser IF-Filter leads to an exceeding of the limit, in this case a worst case correction factor of 20 dB (1 MHz -> 10 kHz) was used c) [1 MHz / 3 MHz] otherwise - Sweep Time: depending on the transmitting signal, the span and the resolution bandwidth 6) The spurious emissions peaks were measured in both vertical and horizontal antenna polarisation during the call is established on the lowest channel, mid channel and on the highest channel. To find the worst case peaks all orientations (X, Y, Z) of the EUT have been measured. Test Requirements / Limits § 2.1053 Measurements required: Field strength of spurious radiation. Measurements shall be made to detect spurious emissions that may be radiated directly from the cabinet, control circuits, power leads, or intermediate circuit elements under normal conditions of installation and operation. Curves or equivalent data shall be supplied showing the magnitude of each harmonic and other Page 19 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 spurious emission. For this test, single sideband, independent sideband, and controlled carrier transmitters shall be modulated under the conditions specified in paragraph (c) of Sec. 2.1049, as appropriate. For equipment operating on frequencies below 890 MHz, an open field test is normally required, with the measuring instrument antenna located in the far-field at all test frequencies. In the event it is either impractical or impossible to make open field measurements (e.g. a broadcast transmitter installed in a building) measurements will be accepted of the equipment as installed. Such measurements must be accompanied by a description of the site where the measurements were made showing the location of any possible source of reflections which might distort the field strength measurements. Information submitted shall include the relative radiated power of each spurious emission with reference to the rated power output of the transmitter, assuming all emissions are radiated from halfwave dipole antennas. (b) The measurements specified in paragraph (a) of this section shall be made for the following equipment: (2) All equipment operating on frequencies higher than 25 MHz. § 2.1057 Frequency spectrum to be investigated. (a) In all of the measurements set forth in Secs. 2.1051 and 2.1053, the spectrum shall be investigated from the lowest radio frequency signal generated in the equipment, without going below 9 kHz, up to at least the frequency shown below: (1) If the equipment operates below 10 GHz: to the tenth harmonic of the highest fundamental frequency or to 40 GHz, whichever is lower. (b) Particular attention should be paid to harmonics and subharmonics of the carrier frequency as well as to those frequencies removed from the carrier by multiples of the oscillator frequency. Radiation at the frequencies of multiplier stages should also be checked. (c) The amplitude of spurious emissions which are attenuated more than 20 dB below the permissible value need not be reported. (d) Unless otherwise specified, measurements above 40 GHz shall be performed using a minimum resolution bandwidth of 1 MHz. § 27.53 Emission limits (h) For operations in the 1710–1755 MHz and 2110–2155 MHz bands, the power of any emission outside a licensee's frequency block shall be attenuated below the transmitter power (P) by at least 43 + 10 log10(P) dB. Remark of the test laboratory: This is calculated to be -13 dBm (effective radiated power) which corresponds to 84.6 dBµV/m (field strength) in a distance of 3 m. (1) Compliance with this provision is based on the use of measurement instrumentation employing a resolution bandwidth of 1 megahertz or greater. However, in the 1 megahertz bands immediately outside and adjacent to the licensee's frequency block, a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emissions are attenuated at least 26 dB below the transmitter power. (2) When measuring the emission limits, the nominal carrier frequency shall be adjusted as close to the licensee's frequency block edges, both upper and lower, as the design permits. (3) The measurements of emission power can be expressed in peak or average values, provided they are expressed in the same parameters as the transmitter power. For reporting only spurious emission levels reaching to the 20dB margin to limit were noted. _______________ Frequency stability _______________ Standard FCC Part 27, Subpart C The test was performed according to FCC §2.1055 Test Description 1) The EUT was placed inside a temperature chamber. 2) The EUT was coupled to a Digital Communication Tester. Refer to chapter "Setup Drawings". 3) The climatic chamber was cycled down/up to a certain temperature, starting with the EUT minimum temperature. 4) After the temperature was stabilized the EUT was switched on and a call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Important Settings: Page 20 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 - Output Power: Maximum - Mid Channel 5) The frequency error of the EUT was recorded by using an internal measurement function of the Digital Communication Tester immediately after the call was established, five minutes after the call was established and ten minutes after the call was established. 6) This measurement procedure was performed for temperature variation from –30°C to +50°C in increments of 10°C, if not otherwise stated in the detailed results. When the EUT did not operate at certain temperature levels, these measurements were left out. Test Requirements / Limits §2.1055 Measurements required: Frequency stability (a) The frequency stability shall be measured with variation of ambient temperature as follows: (1) From -30° to +50° centigrade for all equipment except that specified in paragraphs (a) (2) and (3) of this section. (b) Frequency measurements shall be made at the extremes of the specified temperature range and at intervals of not more than 10° centigrade through the range. A period of time sufficient to stabilize all of the components of the oscillator circuit at each temperature level shall be allowed prior to frequency measurement. The short term transient effects on the frequency of the transmitter due to keying (except for broadcast transmitters) and any heating element cycling normally occurring at each ambient temperature level also shall be shown. Only the portion or portions of the transmitter containing the frequency determining and stabilizing circuitry need be subjected to the temperature variation test. (d) The frequency stability shall be measured with variation of primary supply voltage as follows: (1) Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried battery equipment. (2) For hand carried, battery powered equipment, reduce primary supply voltage to the battery operating end point which shall be specified by the manufacturer. (3) The supply voltage shall be measured at the input to the cable normally provided with the equipment, or at the power supply terminals if cables are not normally provided. Effects on frequency of transmitter keying (except for broadcast transmitters) and any heating element cycling at the nominal supply voltage and at each extreme also shall be shown. §27.54 Frequency stability The frequency stability shall be sufficient to ensure that the fundamental emissions stay within the authorized bands of operation. 7Layers interpretation of limit: To ensure that the frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block following limit was used: +/- 2.5 ppm = 4350 Hz for channel 1450, frequency 1740.0 MHz +/- 2.5 ppm = 4331 Hz for channel 1412, frequency 1732.4 MHz in accordance with FCC Part 22, Subpart H, §22.355, table C-1: Frequency tolerance for the carrier frequency of mobile transmitters in the Public Mobile Service in the frequency range 821 to 896 MHz. __________________ Band edge compliance __________________ Standard FCC Part 27, Subpart C The test was performed according to: FCC §27.53 Test Description 1) The EUT was coupled to a Spectrum Analyser and a Digital Communication Tester through a Power Divider. Refer to chapter "Setup Drawings". 2) The total insertion losses for signal path 1 and signal path 2 were measured. The values were used to correct the readings from the Spectrum Analyser and the Digital Communication Tester. 3) A call was established on a Traffic Channel between the EUT and the Digital Communication Tester. Page 21 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Important Settings: - Output Power: Maximum - Channel: please refer to the detailed results 4) Important Analyser Settings: - Resolution Bandwidth = Video Bandwidth: >1% of the manufacturer’s stated occupied bandwidth Test Requirements / Limits § 27.53 Effective radiated power limits Refer to chapter "Field strength of spurious radiation". Page 22 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 _____________ Subtests HSDPA _____________ Sub- c d d c/d HS CM (dB) MPR (dB) test (SF) (Note1, Note 2) (Note 3) (Note 3) 1 2/15 15/15 64 2/15 4/15 0.0 0.0 2 12/15 15/15 64 12/15 24/15 1.0 0.0 (Note (Note 4) (Note 4) 4) 3 15/15 8/15 64 15/8 30/15 1.5 0.5 4 15/15 4/15 64 15/4 30/15 1.5 0.5 Note 1: ? ACK, ? NACK and ? CQI = 30/15 with  hs = 30/15 *  c . Note 2: For the HS-DPCCH power mask requirement test in clause 5.2C, 5.7A, and the Error Vector Magnitude (EVM) with HS-DPCCH test in clause 5.13.1A, and HSDPA EVM with phase discontinuity in clause 5.13.1AA, ? ACK and ? NACK = 30/15 with  hs = 30/15 *  c , and ? CQI = 24/15 with  hs = 24/15 *  c . Note 3: CM = 1 for c/d =12/15, hs/c=24/15. For all other combinations of DPDCH, DPCCH and HS- DPCCH the MPR is based on the relative CM difference. This is applicable for only UEs that support HSDPA in release 6 and later releases. Note 4: For subtest 2 the c/d ratio of 12/15 for the TFC during the measurement period (TF1, TF0) is achieved by setting the signalled gain factors for the reference TFC (TF1, TF1) to c = 11/15 and d = 15/15. _____________ Subtests HSUPA _____________ Number of E- Loopback Rel99 HSDPA DPDCH Subtest Mode Mode RMC FRC HSUPA Test Channels 12.2kbps 1 Rel6 HSUPA Test Mode 1 RMC H-Set1 HSUPA Loopback 1 12.2kbps 2 Rel6 HSUPA Test Mode 1 RMC H-Set1 HSUPA Loopback 1 12.2kbps 3 Rel6 HSUPA Test Mode 1 RMC H-Set1 HSUPA Loopback 2 12.2kbps 4 Rel6 HSUPA Test Mode 1 RMC H-Set1 HSUPA Loopback 1 12.2kbps 5 Rel6 HSUPA Test Mode 1 RMC H-Set1 HSUPA Loopback 1 Max UL Data Rate Subtest (kb/s) βc/βd βhs βed CM 1 242.1 11/15 22/15 1309/225 1 2 161.3 6/15 12/15 94/75 3 3 524.7 15/9 30/15 47/15 2 4 197.6 2/15 4/15 56/75 3 5 299.6 15/15 30/15 134/15 1 Page 23 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 _____________ Setup Drawings _____________ Principle set-up for radiated measurements Page 24 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 Principle set-up for conducted measurements under nominal conditions Principle set-up for tests under extreme test conditions Page 25 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 this page is intentionally left blank. Page 26 of 27

Reference: MDE_ECOM_1203_FCCc According to: FCC 47 CFR Ch.1 Part 27 6 Index 1 Administrative Data 2 1.1 Project Data 2 1.2 Applicant Data 2 1.3 Test Laboratory Data 2 1.4 Signature of the Testing Responsible 2 1.5 Signature of the Accreditation Responsible 3 2 Test Object Data 3 2.1 General OUT Description 3 2.2 Detailed Description of OUT Samples 4 2.3 OUT Features 4 2.4 Setups used for Testing 5 3 Results 5 3.1 General 5 3.2 List of the Applicable Body 5 3.3 List of Test Specification 5 3.4 Summary 6 3.5 Detailed Results 7 3.5.1 27.4 Field strength of spurious radiation §2.1053, §27.53 7 4 Test Equipment Details 10 4.1 List of Used Test Equipment 10 5 Annex 15 5.1 Additional Information for Report 15 6 Index 27 Page 27 of 27


Document Created: 2013-09-02 11:36:22
Document Modified: 2013-09-02 11:36:22
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC