Test Report

FCC ID: WQJ-KIOSKIII

Test Report

Download: PDF
FCCID_2612142

Report No.: C150205Z03-RP1 FCC 47 CFR PART 15 SUBPART C TEST REPORT for ViVOpay Kiosk III MODEL: ViVOpay Kiosk III Brand: ViVOpay Test Report Number: C150205Z03-RP1 Issued for ID TECH 10721 Walker Street, Cypress, California 90630 Issued by: Compliance Certification Services (Shenzhen) Inc. No.10-1, Mingkeda Logistics Park, NO.18, Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen, China TEL: 86-755-28055000 FAX: 86-755-28055221 Issued Date: March 24, 2015 检 测 CNAS L4818 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NVLAP, NIST or any government agencies. The test results in the report only apply to the tested sample. FCC ID : WQJ-KIOSKIII Page 1 / 26

Report No.: C150205Z03-RP1 Revision History Effect Issue Date Rev. Revisions Page Revised By 00 March 24, 2015 Initial Issue ALL Nancy Fu FCC ID : WQJ-KIOSKIII Page 2 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 TABLE OF CONTENTS 1 TEST CERTIFICATION ................................................................................................. 4 2 EUT DESCRIPTION....................................................................................................... 5 3 TEST METHODOLOGY................................................................................................. 6 3.1. DESCRIPTION OF TEST MODES ...................................................................................... 6 4 TEST METHODOLOGY................................................................................................. 7 4.1. EUT CONFIGURATION ....................................................................................................... 7 4.2. EUT EXERCISE...................................................................................................................7 4.3. GENERAL TEST PROCEDURES ....................................................................................... 7 4.4. FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................................... 8 5 INSTRUMENT CALIBRATION ...................................................................................... 9 6 SETUP OF EQUIPMENT UNDER TEST ....................................................................... 9 6.1. DESCRIPTION OF SUPPORT UNITS................................................................................. 9 6.2. CONFIGURATION OF SYSTEM UNDER TEST ................................................................. 9 7 FACILITIES AND ACCREDITATIONS ........................................................................ 10 7.1. FACILITIES ........................................................................................................................ 10 7.2. ACCREDITATIONS ........................................................................................................... 10 7.3. MEASUREMENT UNCERTAINTY..................................................................................... 10 8 FCC PART 15.225 REQUIREMENTS ......................................................................... 11 8.1. TIMING OF THE TRANSMITTER ...................................................................................... 11 8.2. 99 % EMISSION BANDWIDTH.......................................................................................... 12 8.3. POWER LINE CONDUCTED EMISSIONS MEASUREMENT........................................... 14 8.4. SPURIOUS EMISSIONS MEASUREMENT....................................................................... 19 8.5. FREQUENCY STABILITY.................................................................................................. 25 FCC ID : WQJ-KIOSKIII Page 3 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 1 TEST CERTIFICATION Product ViVOpay Kiosk III Model ViVOpay Kiosk III Brand ViVOpay Tested February 5~ March 24, 2015 ID TECH Applicant 10721 Walker Street, Cypress, California 90630 ID TECH Manufacturer 10721 Walker Street, Cypress, California 90630 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted DEVIATION FROM APPLICABLE STANDARD None We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10: 2013 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.225. The test results of this report relate only to the tested sample EUT identified in this report. Approved by: Reviewed by: Sunday Hu Ruby Zhang Supervisor of EMC Dept. Supervisor of Report Dept. Compliance Certification Service Inc. Compliance Certification Service Inc. FCC ID : WQJ-KIOSKIII Page 4 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 2 EUT DESCRIPTION Product ViVOpay Kiosk III Model Number ViVOpay Kiosk III Brand ViVOpay Model Discrepancy N/A Identify Number C150205Z03-RP1 Received Date February 5, 2015 Power Supply DC7.5V supplied by the adapter DVE / DSA-12PFA-05 FUS 075100 Adapter Manufacturer / I/P: AC100-240V, 50/60Hz, 0.5A Model No. O/P: DC7.5V, 1A DC Output Cable: Unshielded, 1.80m(with a core) Frequency Range 13.56 MHz Transmit Power 63.94dBuV/m(measured at 3m) Modulation Technique ASK Number of Channels 1Channel Antenna Specification PCB antenna with 0dBi gain (Max) Temperature Range 5°C ~ +50°C Hardware Version 80136110 Software Version 80136120 Note: 1. The sample selected for test was engineering sample that approximated to production product and was provided by manufacturer. 2. This submittal(s) (test report) is intended for FCC ID: WQJ-KIOSKIII filing to comply with Section 15.225 of the FCC Part 15, Subpart C Rules. FCC ID : WQJ-KIOSKIII Page 5 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 3 TEST METHODOLOGY 3.1. DESCRIPTION OF TEST MODES The EUT had been tested under operating condition. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in normal link(powered by the adapter) mode only, and powerline conducted emission below 30MHz, which worst case was in normal link mode with charging only. Channel 1 (13.56MHz) was chosen for the final testing. FCC ID : WQJ-KIOSKIII Page 6 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 4 TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.10: 2013 and FCC CFR 47 15.207, 15.209 and 15.225. 4.1. EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 4.2. EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209, 15.225 under the FCC Rules Part 15 Subpart C. 4.3. GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.10: 2013. Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.10: 2013. FCC ID : WQJ-KIOSKIII Page 7 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 4.4. FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 ( 2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. FCC ID : WQJ-KIOSKIII Page 8 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 5 INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 6 SETUP OF EQUIPMENT UNDER TEST 6.1. DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Data Power No. Equipment Model No. Serial No. FCC ID Brand Cable Cord Unshielded 1 Notebook B475 WB04861612 DOC LENOVO N/A 1.80m Note: Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. 6.2. CONFIGURATION OF SYSTEM UNDER TEST See test photographs attached in Appendix II for the actual connections between EUT and support equipment. FCC ID : WQJ-KIOSKIII Page 9 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 7 FACILITIES AND ACCREDITATIONS 7.1. FACILITIES All measurement facilities used to collect the measurement data are located at No10-1, Mingkeda Logistics Park, No.18 Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen, China The sites are constructed in conformance with the requirements of ANSI C63.4, ANSI C63.7 and CISPR Publication 22. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” 7.2. ACCREDITATIONS Our laboratories are accredited and approved by the following accreditation body according to ISO/IEC 17025. USA A2LA China CNAS The measuring facility of laboratories has been authorized or registered by the following approval agencies. Canada Industry Canada Japan VCCI(C-3478, R-3135, T-652, G-624) Taiwan BSMI USA FCC Copies of granted accreditation certificates are available for downloading from our web site, http://www.ccsrf.com 7.3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: Parameter Uncertainty Radiated Emission, 30 to 200 MHz +/-3.6880dB Test Site : 966(2) Radiated Emission, 200 to 1000 MHz +/-3.6695dB Test Site : 966(2) Radiated Emission, 1 to 8 GHz +/-5.1782dB Radiated Emission, 8 to 18 GHz +/-5.2173dB Conducted Emissions +/-3.6836dB Band Width 178kHz Peak Output Power MU +/-1.906dB Band Edge MU +/-0.182dB Channel Separation MU 416.178Hz Duty Cycle MU 0.054ms Frequency Stability MU 226Hz This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. The measured result is above (below) the specification limit by a margin less than the measurement uncertainty; it is therefore not possible to state compliance based on the 95% level of confidence. However, the result indicates that compliance (non-compliance) is more probable than non-compliance) with the specification limit. FCC ID : WQJ-KIOSKIII Page 10 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8 FCC PART 15.225 REQUIREMENTS 8.1. TIMING OF THE TRANSMITTER LIMIT FCC Timing of the transmitter (c) Unless otherwise specified, e.g. Section 15.255(b), when the radiated emission limits are expressed in terms of the average value of the emission, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum value. The exact method of calculating the average field strength shall be submitted with any application for certification or shall be retained in the measurement data file for equipment subject to notification or verification. MEASUREMENT Measurement parameter Detector： Positive peak Sweep time: 100ms Resolution bandwidth: 100kHz Video bandwidth: 300kHz Span: Zero span Trace-Mode: Single sweep Duty cycle of the EUT: 100% RESULT: passed FCC ID : WQJ-KIOSKIII Page 11 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.2. 99 % EMISSION BANDWIDTH LIMIT None; for reporting purposes only. MEASUREMENT EQUIPMENT USED Radiated Emission Test Site 966(2) Serial Last Due Name of Equipment Manufacturer Model Number Number Calibration Calibration PSA Series Spectrum Agilent E4446A US44300399 03/01/2015 03/01/2016 Analyzer EMI TEST RECEIVER ROHDE&SCHWARZ ESCI 100783 03/09/2015 03/08/2016 Amplifier MITEQ AM-1604-3000 1123808 03/18/2015 03/17/2016 High Noise Amplifier Agilent 8449B 3008A01838 03/18/2015 03/17/2016 Board-Band Horn Antenna Schwarzbeck BBHA 9170 9170-497 07/10/2014 07/09/2015 Bilog Antenna SCHAFFNER CBL6143 5082 03/01/2015 03/01/2016 Horn Antenna SCHWARZBECK BBHA9120 D286 03/01/2015 03/01/2016 Loop Antenna COM-POWER AL-130 121044 09/27/2014 09/26/2015 Turn Table N/A N/A N/A N.C.R N.C.R Controller Sunol Sciences SC104V 022310-1 N.C.R N.C.R Controller CT N/A N/A N.C.R N.C.R Temp. / Humidity Meter Anymetre JR913 N/A 02/28/2015 02/27/2016 Antenna Tower SUNOL TLT2 N/A N.C.R N.C.R Test S/W FARAD LZ-RF / CCS-SZ-3A2 Test Configuration EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW= 1kHz, VBW = 3kHz, Span = 10kHz, Sweep = auto. 4. Mark the peak frequency and 26dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted. FCC ID : WQJ-KIOSKIII Page 12 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 Test Data Bandwidth (TX / CH 13.56MHz) FCC ID : WQJ-KIOSKIII Page 13 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.3. POWER LINE CONDUCTED EMISSIONS MEASUREMENT 8.3.1. LIMITS OF CONDUCTED EMISSIONS MEASUREMENT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Limits Frequency Range (dBμV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 NOTE: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. (3) All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. TEST INSTRUMENTS Conducted Emission Test Site Name of Last Due Manufacturer Model Number Serial Number Equipment Calibration Calibration EMI TEST RECEIVER ROHDE&SCHWARZ ESCI 100783 04/21/2014 04/21/2015 LISN(EUT) ROHDE&SCHWARZ ENV216 101543-WX 03/01/2015 03/01/2016 LISN EMCO 3825/2 8901-1459 03/01/2015 03/01/2016 Temp. / Humidity Meter VICTOR HTC-1 N/A 03/17/2015 03/17/2016 Test S/W FARAD EZ-EMC/ CCS-3A1-CE NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Request. FCC ID : WQJ-KIOSKIII Page 14 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.3.2. TEST PROCEDURES (please refer to measurement standard) z The EUT and Support equipment, if needed, was placed on a non-conducted table, which is 0.8m above the ground plane and 0.4m away from the conducted wall. z The test equipment EUT installed received AC main power, through a Line Impedance Stabilization Network (LISN), which supplied power source and was grounded to the ground plane. All support equipment power received from a second LISN. The two LISNS provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. z The EUT test program was started. Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT. z The frequency range from 150 kHz to 30 MHz was searched. The test data of the worst-case condition(s) was recorded. Emission levels under limit 20dB were not recorded. FCC ID : WQJ-KIOSKIII Page 15 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.3.3. TEST SETUP Vert. reference plane EMI receiver 40cm EUT 80cm LISN Reference ground plane z For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 8.3.4. DATA SAMPLE Frequency QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Line Reading Reading Factor Result Result Limit Limit Margin Margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) (L1/L2) X.XXXX 32.69 25.65 11.52 44.21 37.17 65.78 55.79 -21.57 -18.62 L1 Factor = Insertion loss of LISN + Cable Loss Result = Quasi-peak Reading/ Average Reading + Factor Limit = Limit stated in standard Margin = Result (dBuV) – Limit (dBuV) L1 = Hot side L2 = Neutral side FCC ID : WQJ-KIOSKIII Page 16 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.3.5. TEST RESULTS Model No. ViVOpay Kiosk III RBW,VBW 9 kHz Environmental o 22 C, 45% RH Test Mode Normal Conditions Tested by Eve Wang Line L1 Test Date March 24, 2015 Frequency QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Remark Reading Reading Factor Result Result Limit Limit Margin Margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) (Pass/Fail) 0.1860 44.79 11.92 9.66 54.45 21.58 64.21 54.21 -9.76 -32.63 Pass 0.2140 44.20 17.82 9.69 53.89 27.51 63.04 53.05 -9.15 -25.54 Pass 0.3620 39.84 24.73 9.68 49.52 34.41 58.68 48.68 -9.16 -14.27 Pass 2.0180 37.29 24.90 9.73 47.02 34.63 56.00 46.00 -8.98 -11.37 Pass 7.4900 39.30 25.66 9.80 49.10 35.46 60.00 50.00 -10.90 -14.54 Pass 13.5620 41.41 37.55 9.90 51.31 47.45 60.00 50.00 -8.69 -2.55 Pass Note: 1. Measuring frequencies from 0.15 MHz to 30MHz. 2. The emissions measured in frequency range from 0.15 MHz to 30MHz were made with an instrument using Peak detector, Quasi-peak detector and average detector. 3. “---” denotes the emission level was or more than 2dB below the Average limit. 4. The IF bandwidth of SPA between 0.15MHz to 30MHz was 10kHz; the IF bandwidth of Test Receiver between 0.15MHz to 30MHz was 9kHz; 5. L1= Line One (Live Line) FCC ID : WQJ-KIOSKIII Page 17 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 Model No. ViVOpay Kiosk III RBW,VBW 9 kHz Environmental o 22 C, 45% RH Test Mode Normal Conditions Tested by Eve Wang Line L2 Test Date March 24, 2015 Frequency QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average Remark Reading Reading Factor Result Result Limit Limit Margin Margin (MHz) (dBuV) (dBuV) (dB) (dBuV) (dBuV) (dBuV) (dBuV) (dB) (dB) (Pass/Fail) 0.2540 40.18 22.03 9.77 49.95 31.80 61.62 51.63 -11.67 -19.83 Pass 0.3980 36.35 21.75 9.71 46.06 31.46 57.89 47.90 -11.83 -16.44 Pass 0.4900 36.54 22.26 9.68 46.22 31.94 56.17 46.17 -9.95 -14.23 Pass 0.7780 33.14 12.91 9.73 42.87 22.64 56.00 46.00 -13.13 -23.36 Pass 6.3859 35.83 16.62 9.78 45.61 26.40 60.00 50.00 -14.39 -23.60 Pass 13.5620 41.82 38.02 9.76 51.58 47.78 60.00 50.00 -8.42 -2.22 Pass Note: 1. Measuring frequencies from 0.15 MHz to 30MHz. 2. The emissions measured in frequency range from 0.15 MHz to 30MHz were made with an instrument using Peak detector, Quasi-peak detector and average detector. 3. “---” denotes the emission level was or more than 2dB below the Average limit. 4. The IF bandwidth of SPA between 0.15MHz to 30MHz was 10kHz; the IF bandwidth of Test Receiver between 0.15MHz to 30MHz was 9kHz; 5. L2= Line Two (Neutral Line) FCC ID : WQJ-KIOSKIII Page 18 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.4. SPURIOUS EMISSIONS MEASUREMENT 8.4.1. LIMITS OF RADIATED EMISSIONS MEASUREMENT LIMIT According to §15.225, (a) The field strength of any emissions within the band 13.553 – 13.567 MHz shall not exceed 15,848 microvolts / meter at 30 meters. (b) Within the bands 13.410 – 13.553 MHz and 13.567 -13.710 MHz, the field strength of any emissions shall not exceed 334 microvolts / meter at 30 meters. (c) Within the bands 13.110 – 13.410 MHz and 13.710 – 14.010 MHz the field strength of any emissions shall not exceed 106 microvolts / meter at 30 meters. (d) The field strength of any emissions appearing outside of the 13.110 – 14.010 MHz and shall not exceed the general radiated emission limits in §15.209. 1. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency (MHz) Field Strength (μV/m) Measurement Distance (m) 0.009-0.490 2400/F(kHz) 300 0.490-1.705 24000/F(kHz) 30 1.705-30.0 30 30 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. FCC ID : WQJ-KIOSKIII Page 19 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.4.2. TEST INSTRUMENTS Radiated Emission Test Site 966(2) Serial Last Due Name of Equipment Manufacturer Model Number Number Calibration Calibration PSA Series Spectrum Agilent E4446A US44300399 03/01/2015 03/01/2016 Analyzer EMI TEST RECEIVER ROHDE&SCHWARZ ESCI 100783 03/09/2015 03/08/2016 Amplifier MITEQ AM-1604-3000 1123808 03/18/2015 03/17/2016 High Noise Amplifier Agilent 8449B 3008A01838 03/18/2015 03/17/2016 Board-Band Horn Antenna Schwarzbeck BBHA 9170 9170-497 07/10/2014 07/09/2015 Bilog Antenna SCHAFFNER CBL6143 5082 03/01/2015 03/01/2016 Horn Antenna SCHWARZBECK BBHA9120 D286 03/01/2015 03/01/2016 Loop Antenna COM-POWER AL-130 121044 09/27/2014 09/26/2015 Turn Table N/A N/A N/A N.C.R N.C.R Controller Sunol Sciences SC104V 022310-1 N.C.R N.C.R Controller CT N/A N/A N.C.R N.C.R Temp. / Humidity Meter Anymetre JR913 N/A 02/28/2015 02/27/2016 Antenna Tower SUNOL TLT2 N/A N.C.R N.C.R Test S/W FARAD LZ-RF / CCS-SZ-3A2 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. N.C.R = No Calibration Required. 8.3.3 TEST PROCEDURE (please refer to measurement standard) 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Belove 30MHz: 9kHz~150kHz: RBW=200Hz / VBW=600Hz / Sweep=AUTO 150kHz~30MHz: RBW=9kHz / VBW=27kHz / Sweep=AUTO Above 30MHz: RBW=100kHz / VBW=300kHz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. FCC ID : WQJ-KIOSKIII Page 20 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.4.2.1. TEST SETUP Below 30MHz Anten na tower 10m Loop antenna EU T 4m Spe ctrum / Re ce ive r Turnta ble 1m 0.8m P re -a mp R ef er ence gr ound pla ne Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. FCC ID : WQJ-KIOSKIII Page 21 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.4.2.2. DATA SAMPLE Below 1GHz Correction Antenna Frequency Reading Result Limit Margin Remark Factor Pole (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) (V/H) XXX.XXXX 37.47 -16.41 21.06 40.00 -18.94 V Peak Above 1GHz Correction Antenna Frequency Reading Result Limit Margin Remark Factor Pole (MHz) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) (V/H) XXXX.XXXX 55.54 4.56 60.10 74.00 -13.90 V Peak XXXX.XXXX 29.66 4.56 34.22 54.00 -19.78 V AVG Frequency (MHz) = Emission frequency in MHz Reading (dBuV) = Uncorrected Analyzer / Receiver reading Correction Factor (dB/m) = Antenna factor + Cable loss – Amplifier gain Result (dBuV/m) = Reading (dBuV) + Corr. Factor (dB/m) Limit (dBuV/m) = Limit stated in standard Margin (dB) = Result (dBuV/m) – Limit (dBuV/m) Q.P. = Quasi-peak Reading Peak = Peak Reading AVG = Average Reading FCC ID : WQJ-KIOSKIII Page 22 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.4.2.3. TEST RESULTS Blow 1GHz Operation Mode: TX / CH 1 (13.56) Test Date: March 20, 2015 Temperature: 24°C Tested by: Eve Wang Humidity: 52 % RH Polarity: Ver. / Hor. Fundamental Frequency Reading Correction Result Limit Margin Remark (MHz) (dBuV) Factor (dBuV/m) (dBuV/m) (dB) (dB/m) 13.5600 49.65 14.29 63.94 124.00 -60.06 Peak FCC ID : WQJ-KIOSKIII Page 23 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 Frequency Reading Correction Result Limit Margin Antenna Remark Factor Pole (MHz) (dBuV) (dB/m) (dBuV/m) (dBuV/m) (dB) (V/H) 38.7300 42.59 -11.27 31.32 40.00 -8.68 V Peak 99.8400 38.64 -14.13 24.51 43.50 -18.99 V Peak 199.7500 38.38 -12.20 26.18 43.50 -17.32 V Peak 600.3600 37.79 -5.84 31.95 46.00 -14.05 V Peak 666.3200 45.58 -4.87 40.71 46.00 -5.29 V Peak 900.0900 32.91 -2.33 30.58 46.00 -15.42 V Peak 39.7000 39.07 -11.25 27.82 40.00 -12.18 H Peak 232.7300 42.12 -10.85 31.27 46.00 -14.73 H Peak 299.6600 40.48 -10.01 30.47 46.00 -15.53 H Peak 600.3600 37.45 -5.84 31.61 46.00 -14.39 H Peak 666.3200 40.40 -4.87 35.53 46.00 -10.47 H Peak 834.1300 36.57 -3.07 33.50 46.00 -12.50 H Peak **Note: The emission found is too lower to record between lowest internal used/generated frequency to 30 MHz. REMARKS: 1. Radiated emissions measured in frequency range from 9kHz to 1GHz were made with an instrument using peak/quasi-peak detector mode. 2. Quasi-peak test would be performed if the peak result were greater than the quasi-peak limit or as required by the applicant. 3. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with “ N/A ” remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. 4. Margin (dB) = Remark result (dBuV/m) – Quasi-peak limit (dBuV/m) FCC ID : WQJ-KIOSKIII Page 24 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 8.5. FREQUENCY STABILITY LIMIT According to §15.225(e), the frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating frequency over a temperature variation of –20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery. Test Configuration Temperature and Voltage Measurement (under normal and extreme test conditions) Temperature Chamber Spectrum Analyzer EUT AC/DC Power supply TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the environment into appropriate environment. 4. Set the spectrum analyzer as RBW=1kHz, VBW = RBW, Span = 200kHz, Sweep = auto. 5. Mark the peak frequency and measure the frequency tolerance using frequency counter function. 6. Repeat until all the results are investigated. FCC ID : WQJ-KIOSKIII Page 25 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No.: C150205Z03-RP1 TEST RESULTS No non-compliance noted. Temperature Variations Measured Delta Temp. Voltage Tolerance Limit Margin Result o Frequency Frequency ( C) (VAC) (%) (±%) (%) (Pass/Fail) (MHz) (Hz) -20 13.56008 10 0.00007 0.01 -0.00993 Pass -10 13.56003 30 0.00022 0.01 -0.00978 Pass 0 13.56001 10 0.00007 0.01 -0.00993 Pass 10 13.56017 170 0.00125 0.01 -0.00875 Pass 7.5 20 13.56001 10 0.00007 0.01 -0.00993 Pass 30 13.56008 80 0.00059 0.01 -0.00941 Pass 40 13.55998 20 0.00015 0.01 -0.01015 Pass 50 13.56010 100 0.00074 0.01 -0.00926 Pass Voltage Variations Measured Delta Temp. Voltage Tolerance Limit Margin Result Frequency Frequency (oC) (VAC) (%) (±%) (%) (Pass/Fail) (MHz) (Hz) 6.75 13.56015 150 0.00111 0.01 -1.00889 Pass 20 7.50 13.56001 10 0.00007 0.01 -2.00993 Pass 8.25 13.56004 40 0.00029 0.01 -3.00971 Pass FCC ID : WQJ-KIOSKIII Page 26 / 26 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.


Document Created: 2015-05-12 10:47:11
Document Modified: 2015-05-12 10:47:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC