Test report

FCC ID: WDS-T01

Test Report

Download: PDF
FCCID_1489261

Shenzhen Certification Technology Service Co., Ltd 3F, Bldg27,Area A, Tanglang Industrial Zone, Xili Town, Nanshan District, ShenZhen, Guang dong, P.R. China. TEST REPORT FCC ID: WDS-T01 Applicant : SAGE HUMAN ELECTRONICS INTERNATIONAL CO., LTD Address : Floor 4, Building A9, QingHu Industry Zone, Silicon Valley Power, LongHua Town, Shenzhen City, China Equipment under Test (EUT): Name : FM Transmitter Model : T01 Standards : FCC Part15.239 Report No. : STE110613478 Date of Test : June 15-17, 2011 Date of Issue : June 18, 2011 Test Result : PASS * * In the configuration tested, the EUT complied with the standards specified above Authorized Signature (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Certification Technology Service Co., Ltd. Or test done by Shenzhen Certification Technology Service Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Certification Technology Service Co., Ltd. Approvals in writing. FCC ID: WDS-T01 Page 1 of 30

Report No.:STE110613478 TABLE OF CONTENT Description Page 1 General Information ---------------------------------------------------------------------3 1.1 Description of Device (EUT) ------------------------------------------------------------------- 3 1.2 Description of Test Facility --------------------------------------------------------------------- 4 2 Test Equipment List ---------------------------------------------------------------------4 3 Test Procedure ---------------------------------------------------------------------------5 4 Summary of Measurement ------------------------------------------------------------5 5 POWER LINE CONDUCTED EMISSION -----------------------------------------6 5.1 Conducted Emission Limits(15.209&249) --------------------------------------------------- 7 5.3 Test Setup-------------------------------------------------------------------------------------------- 7 5.3 Test Procedure-------------------------------------------------------------------------------------- 7 5.4 Test Resluts ----------------------------------------------------------------------------------------- 8 6 Radiated Emission Test ----------------------------------------------------------------9 6.1 Radiated Emission Limits(15.209&239) --------------------------------------------------- 10 6.2 Test Setup for Emission measurement ---------------------------------------------------- 10 6.3 Test Procedure ----------------------------------------------------------------------------------- 12 6.4 Test Condition ------------------------------------------------------------------------------------ 13 7 Bandwidth Test ------------------------------------------------------------------------- 19 7.1 Limit for Bandwidth ------------------------------------------------------------------------------ 19 7.2 Method of measurement ----------------------------------------------------------------------- 19 7.3 Test Setup------------------------------------------------------------------------------------------ 19 7.4 Test Results --------------------------------------------------------------------------------------- 19 8 Band Edge Test ------------------------------------------------------------------------ 21 8.1 Test Limit------------------------------------------------------------------------------------------ 21 8.2 Test Procedure ---------------------------------------------------------------------------------- 21 8.3 Test Results -------------------------------------------------------------------------------------- 21 9 Antenna Requirement ---------------------------------------------------------------- 23 9.1 Standard requirement--------------------------------------------------------------------------- 23 9.2 Result ----------------------------------------------------------------------------------------------- 23 10 Photographs of Test Setup ---------------------------------------------------------- 24 11 Photographs of EUT ------------------------------------------------------------------ 26 FCC ID: WDS-T01 Page 2 of 30

Report No.:STE110613478 1 General Information 1.1 Description of Device (EUT) Trade Name : N/A EUT : FM Transmitter Model No. : T01 : Type of Antenna : Integral Antenna 88.1-107.9MHZ(All turning channels is manually verified Operation Frequency : Which will be only between 88MHZ~108MHZ) Modulation type FM Power Supply : DC 3.7V Supply by adapter or DC 5V Supply by PC Rated RF output Power 41.34 dBuV(AV detector) Applicant : SAGE HUMAN ELECTRONICS INTERNATIONAL CO., LTD Address : Floor 4, Building A9, QingHu Industry Zone, Silicon Valley Power, LongHua Town, Shenzhen City, China Manufacturer : SAGE HUMAN ELECTRONICS INTERNATIONAL CO., LTD Address : Floor 4, Building A9, QingHu Industry Zone, Silicon Valley Power, LongHua Town, Shenzhen City, China FCC ID: WDS-T01 Page 3 of 30

Report No.:STE110613478 1.2 Description of Test Facility Shenzhen Certification Technology Service Co.,Ltd. 3F, Bldg.27, Area A, Tanglang Industrial Zone, Xili Town, Nanshan District, Shenzhen 518055, Guangdong, P.R. China FCC Registered No.:305283 2 Test Equipment List Equipment Manufacture Model No. Serial No. Last cal. Cal Interval 3m Semi-Anechoic ETS-LINDGREN N/A SEL0017 06/06/2011 1Year Spectrum analyzer Agilent E4443A MY46185649 06/06/2011 1Year Receiver R&S ESCI 100492 04/06/2011 1Year Receiver R&S ESCI 101202 07/01/2011 1Year Bilog Antenna Sunol JB3 A121206 04/06/2011 1Year L.I.S.N. R&S ESH3-Z5 100305 16/06/2011 1Year Horn Antenna EMCO 3115 640201028-0 04/06/2011 1Year 6 Power Meter Anritsu ML2487A 6K00001491 23/02/2011 1Year ETS Horn Antenna ETS 3160 SEL0076 12/08/2010 1Year Active Loop Antenna Beijing Daze ZN30900A SEL0097 15/06/2011 1Year Cable Resenberger N/A No.1 04/06/2011 1Year Cable SCHWARZBECK N/A No.2 04/06/2011 1Year Cable SCHWARZBECK N/A No.3 04/06/2011 1Year Pre-amplifier R&S AFS42-00101 SEL0081 06/06/2011 1Year 800-25-S-42 Pre-amplifier R&S AFS33-18002650 SEL0080 06/06/2011 1Year -30-8P-44 FCC ID: WDS-T01 Page 4 of 30

Report No.:STE110613478 3 Test Procedure POWER LINE CONDUCTED INTERFERENCE: The test procedure used was ANSI Standard C63.4-2003 using a 50ｕH LISN. Both Lines were observed. The bandwidth of the receiver was 10kHz with an appropriate sweep speed. The ambient temperature of the EUT was 25℃ with a humidity of 58%. RADIATION INTERFERENCE: The test procedure used was ANSI Standard C63.4-2003 using a ANRITSU spectrum analyzer with a pre-selector. The analyzer was calibrated in dB above a micro volt at the output of the antenna. The resolution bandwidth was 100kHz and the video bandwidth was 300 kHz up to 1 GHz and 1 MHz with a video BW of 3MHz above 1 GHz. The ambient temperature of the EUT was 25℃ with a humidity of 58%. FORMULA OF CONVERSION FACTORS: The Field Strength at 3m was established by adding the meter reading of the spectrum analyzer (which is set to read in units of dBuV) to the antenna correction factor supplied by the antenna manufacturer and cable loss. The antenna correction factors and cable loss are stated in terms of dB. The gain of the Pre-selector was accounted for in the Spectrum Analyzer Meter Reading. Example: Freq (MHz) METER READING + ACF + CABLE = FS 33.20 dBuV + 10.36 dB + 0.9 dB= 44.46 dBuV/m @ 3m ANSI STANDARD C63.4-2003 10.1.7 MEASUREMENT PROCEDURES: The EUT was placed on a table 80 cm high and with dimensions of 1m by 1.5m. The EUT was placed in the center of the table (1.5m side). The table used for radiated measurements is capable of continuous rotation. When an emission was found, the table was rotated to produce the maximum signal strength. At this point, the antenna was raised and lowered from 1m to 4m. The antenna was placed in both the horizontal and vertical planes. The situation was similar for the conducted measurement except that the table did not rotate. The EUT was setup as described in ANSI Standard C63.4-2003 10.1.7 with the EUT 40 cm from the vertical ground wall. 4 Summary of Measurement FCC ID: WDS-T01 Page 5 of 30

Report No.:STE110613478 Note: The EUT has been tested as an independent unit. And Continual transmitting in Test Item Test Requirement Standard Paragraph Result Antenna Requirement FCC PART15 15.203 Compliance Conducted Emission FCC PART15 15.207 Compliance Radiation Emission FCC PART15 15.209&15.239 Compliance Bandwidth Requirement FCC PART15 15.239 Compliance Band edge Requirement FCC PART15 15.239 Compliance maximum power (The new battery be used during Test). The EUT has been tested on under the worst case test mode, has tested the modulation mode. 5 POWER LINE CONDUCTED EMISSION FCC ID: WDS-T01 Page 6 of 30

Report No.:STE110613478 5.1 Conducted Emission Limits(15.209&249) Frequency Limits dB(μV) MHz Quasi-peak Level Average Level 0.15 -0.50 66 -56* 56 - 46* 0.50 -5.00 56 46 5.00 -30.00 60 50 Notes: 1. *Decreasing linearly with logarithm of frequency. 2. The lower limit shall apply at the transition frequencies. 3.The limit decreases in line with the logarithm of the frequency in the rang of 0.15 to 0.50 MHz. 5.3 Test Setup 5.3 Test Procedure The EUT is put on the plane 0.8m high above the ground by insulating support and is FCC ID: WDS-T01 Page 7 of 30

Report No.:STE110613478 connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC lines are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to ANSI C63.4-2003 on Conducted Emission Measurement. The bandwidth of test receiver (R & S ESCS30) is set at 9 kHz. 5.4 Test Resluts PASS Detailed information please see the following page. FCC ID: WDS-T01 Page 8 of 30

Report No.:STE110613478 EUT FM Transmitter Model Name T01 Temperature 25oC Relative Humidity 58% Pressure 960hPa Test voltage DC 5V supply by PC Test Mode Noraml FREQ PEAK Q.P. AVG Q.P. AVG Q.P. AVG MHz See See Limit Limit Margin Margin NOTE dBuV Peak Peak dBuV dBuV dBuV dBuV dBuV dBuV 0.173 40.10 --- --- 64.86 54.86 -24.76 -14.76 L1 0.301 38.87 --- --- 60.32 50.32 -21.45 -11.45 L1 0.592 39.24 --- --- 56.00 46.00 -16.76 -6.76 L1 1.698 38.95 --- --- 56.00 46.00 -17.05 -7.05 L1 4.653 38.82 --- --- 56.00 46.00 -17.18 -7.18 L1 9.607 38.02 --- --- 60.00 50.00 -21.98 -11.98 L1 0.251 38.15 --- --- 69.91 59.91 -23.76 -13.76 L2 0.362 37.49 --- --- 58.78 48.78 -21.29 -11.29 L2 0.573 37.33 --- --- 56.00 46.00 -18.67 -8.67 L2 1.453 38.10 --- --- 56.00 46.00 -17.90 -7.90 L2 2.931 38.60 --- --- 56.00 46.00 -17.40 -7.40 L2 10.407 37.87 --- --- 60.00 50.00 -22.13 -12.13 L2 Note: L1=Line One (Live Line) /L2= Line Two (Neutral Line) PEAK greater than QP greater than AVG 6 Radiated Emission Test FCC ID: WDS-T01 Page 9 of 30

Report No.:STE110613478 6.1 Radiated Emission Limits(15.209&239) Frequency Field Strength (MHZ) Limits at 3 metres (watts,e.i.r.p.) uV/m dB uV/m Measurement distance(m) 0.009-0.490 2400/F(kHz) XX 300 0.490-1.705 24000/F(kHz) XX 30 1.705-30 30 29.5 30 30~88 100(3nW) 40 3 88~216 150(6.8nW) 43.5 3 216~960 200(12nW) 46 3 Above960 500(75nW) 54 3 Carrier 250 48(AV) 3 frequency Carrier 68(PK) 3 frequency NOTE: a) The tighter limit applies at the band edges. b) Emission Level(dB uV/m)=20log Emission Level(uV/m) c) XX means the limit is unsure 6.2 Test Setup for Emission measurement Test Setup for Emission Below 30MHz FCC ID: WDS-T01 Page 10 of 30

Report No.:STE110613478 Test Setup for Emission above 30MHz Test Setup for Emission above 1GHz FCC ID: WDS-T01 Page 11 of 30

Report No.:STE110613478 6.3 Test Procedure a) The measuring distance of 3m shall be used for measurements at frequency up to 1GHZ and above 1 GHZ, The EUT was placed on a rotating 0.8 m high above ground. The table was rotated 360 degrees to determine the position of the highest radiation b) The Test antenna shall vary between 1m and 4m. Both Horizontal and Vertical antenna are set to make measurement. c) The initial step in collecting conducted emission data is a spectrum analyzer Peak detector mode pre-scanning the measurement frequency range. Significant Peaks are then marked and then Qusia Peak Detector mode premeasured d) If Peak value comply with QP limit Below 1GHZ.The EUT deemed to comply with QP limit. But the Peak value and average value both need to comply with applicable limit above 1GHZ. e) Repeated step a and d test with EUT in X, Y,Z position, and the maximum emissions data were recorded when EUT in X position as the test photo indicated. f) For the actual test configuration, please see the test setup photo. FCC ID: WDS-T01 Page 12 of 30

Report No.:STE110613478 g) Test Equipment Setting For emission test: 30MHZ~1GHZ: RBW 120KHZ VBW 300KHZ Above 1GHZ : RBW 1MHZ VBW 3MHZ for Peak value RBW 1MHZ VBW 10HZ for Average Value 6.4 Test Condition A continuously playing MP3 audio source (Ipod, Brand: Apple, Model: A1238, S/N: 2Z8181UQYMV) was connected during the test. The volume of the audio source was set to maximum to represent the worst case. The transmitter was transmitting continuously. We have scanned up the 10th harmonics about the EUT. FCC ID: WDS-T01 Page 13 of 30

Report No.:STE110613478 6.5 Test Results Radiated Emissions Result of Outside the band (88~108MHZ) EUT FM Transmitter Model Name T01 Temperature 26oC Relative Humidity 58% Pressure 960hPa Test voltage DC 3.7V Supply by battery Test Mode TX TX frequency 88.1MHZ Antenna polarization: Vertical Frequency Reading Cable Antenna Amplifier Correct Measurement Limit Loss Factor Factor Result line Over MHZ dBuV dB dB Gain dB dBuV/m dBuV/m Margin 40.670 39.39 0.55 14.07 29.81 -15.19 24.20 40.00 -15.80 147.370 38.48 1.12 13.90 28.90 -13.88 24.60 43.50 -18.90 353.010 39.53 2.21 13.87 29.28 -13.20 26.33 46.00 -19.67 438.370 39.72 2.67 15.68 29.47 -11.12 28.60 46.00 -17.40 507.240 40.19 3.01 16.65 29.63 -9.97 30.22 46.00 -15.78 592.610 39.18 3.18 18.16 29.80 -8.46 30.72 46.00 -15.28 -- -- -- -- -- -- -- -- -- Antenna polarization: Horizontal Frequency Reading Cable Antenna Amplifier Correct Measurement Limit Over Loss Factor Factor Result line MHZ dBuV dB dB Gain Db dBuV/m dBuV/m Margin 136.710 41.43 1.06 13.22 28.90 -14.62 26.81 43.50 -16.69 462.620 40.14 2.80 16.09 29.52 -10.63 29.51 46.00 -16.49 597.450 39.73 3.19 18.28 29.82 -8.35 31.38 46.00 -14.62 702.210 40.40 3.40 19.69 29.75 -6.66 33.74 46.00 -12.26 793.390 40.27 3.59 20.66 29.65 -5.40 34.87 46.00 -11.13 925.310 40.63 3.85 21.97 29.63 -3.81 36.82 46.00 -9.18 -- -- -- -- -- -- -- -- -- FCC ID: WDS-T01 Page 14 of 30

Report No.:STE110613478 EUT FM Transmitter Model Name T01 Temperature 26oC Relative Humidity 58% Pressure 960hPa Test voltage DC 3.7V Supply by battery Test Mode TX(IPod) TX frequency 98.1MHZ Antenna polarization: Vertical Frequency Reading Cable Antenna Amplifier Correct Measurement Limit Loss Factor Factor Result line Over MHZ dBuV dB dB Gain dB dBuV/m dBuV/m Margin 40.670 39.39 0.55 14.07 29.81 -15.19 24.20 40.00 -15.80 147.370 38.48 1.12 13.90 28.90 -13.88 24.60 43.50 -18.90 353.010 39.53 2.21 13.87 29.28 -13.20 26.33 46.00 -19.67 438.370 39.72 2.67 15.68 29.47 -11.12 28.60 46.00 -17.40 507.240 40.19 3.01 16.65 29.63 -9.97 30.22 46.00 -15.78 592.610 39.18 3.18 18.16 29.80 -8.46 30.72 46.00 -15.28 -- -- -- -- -- -- -- -- -- Antenna polarization: Horizontal Frequency Reading Cable Antenna Amplifier Correct Measurement Limit Over Loss Factor Factor Result line MHZ dBuV dB dB Gain Db dBuV/m dBuV/m Margin 136.710 41.43 1.06 13.22 28.90 -14.62 26.81 43.50 -16.69 462.620 40.14 2.80 16.09 29.52 -10.63 29.51 46.00 -16.49 597.450 39.73 3.19 18.28 29.82 -8.35 31.38 46.00 -14.62 702.210 40.40 3.40 19.69 29.75 -6.66 33.74 46.00 -12.26 793.390 40.27 3.59 20.66 29.65 -5.40 34.87 46.00 -11.13 925.310 40.63 3.85 21.97 29.63 -3.81 36.82 46.00 -9.18 -- -- -- -- -- -- -- -- -- FCC ID: WDS-T01 Page 15 of 30

Report No.:STE110613478 EUT FM Transmitter Model Name T01 Temperature 26oC Relative Humidity 58% Pressure 960hPa Test voltage DC 3.7V Supply by battery Test Mode TX(IPod) TX frequency 107.9MHZ Antenna polarization: Vertical Frequency Reading Cable Antenna Amplifier Correct Measurement Limit Loss Factor Factor Result line Over MHZ dBuV dB dB Gain dB dBuV/m dBuV/m Margin 40.670 39.39 0.55 14.07 29.81 -15.19 24.20 40.00 -15.80 147.370 38.48 1.12 13.90 28.90 -13.88 24.60 43.50 -18.90 353.010 39.53 2.21 13.87 29.28 -13.20 26.33 46.00 -19.67 438.370 39.72 2.67 15.68 29.47 -11.12 28.60 46.00 -17.40 507.240 40.19 3.01 16.65 29.63 -9.97 30.22 46.00 -15.78 592.610 39.18 3.18 18.16 29.80 -8.46 30.72 46.00 -15.28 -- -- -- -- -- -- -- -- -- Antenna polarization: Horizontal Frequency Reading Cable Antenna Amplifier Correct Measurement Limit Over Loss Factor Factor Result line MHZ dBuV dB dB Gain Db dBuV/m dBuV/m Margin 136.710 41.43 1.06 13.22 28.90 -14.62 26.81 43.50 -16.69 462.620 40.14 2.80 16.09 29.52 -10.63 29.51 46.00 -16.49 597.450 39.73 3.19 18.28 29.82 -8.35 31.38 46.00 -14.62 702.210 40.40 3.40 19.69 29.75 -6.66 33.74 46.00 -12.26 793.390 40.27 3.59 20.66 29.65 -5.40 34.87 46.00 -11.13 925.310 40.63 3.85 21.97 29.63 -3.81 36.82 46.00 -9.18 -- -- -- -- -- -- -- -- -- Notes: --Means other frequency and mode comply with standard requirements and at least have 20dB margin. Correct Factor=Cable Loss+Antenna Factor-Amplifier Gain Measurement Result=Reading + Correct Factor Margin=Measurement Result-Limit FCC ID: WDS-T01 Page 16 of 30

Report No.:STE110613478 Radiated Emissions Result of Inside band (88~108MHZ) EUT FM Wireless Transmitter Model Name SV-301FT o Temperature 26 C Relative Humidity 58% Pressure 960hPa Test voltage DC 3.7V Supply by battery Test Mode TX (IPod) Antenna polarization Horizontal/Vertical Channel Low(88.1MHZ) Fre. Plority Reading Antenna Cable Amplifier Correct Measure Result Limit Margin dBuV Factor Loss Gain Factor dBuV/m dBuV/m dB MHz H/V dB dB dB dB 88.1 H 76.82（PK） 5.7 0.57 26.65 -20.38 56.44 68.00 -11.56 88.1 H 59.43 (AV) 5.7 0.57 26.65 -20.38 39.05 48.00 -8.95 -- H -- -- -- -- -- -- -- -- 88.1 V 77.25（PK） 5.7 0.57 26.65 -20.38 56.87 68.00 -11.13 88.1 V 59.92 (AV) 5.7 0.57 26.65 -20.38 39.54 48.00 -8.46 -- V -- -- -- -- -- -- -- -- Channel Middle(98.1MHZ) Fre. Plority Reading Antenna Cable Amplifier Correct Measure Result Limit Margin dBuV Factor Loss Gain Factor dBuV/m dBuV/m dB MHz H/V dB dB dB dB 98.1 H 73.41 （PK） 8.4 0.61 26.75 -17.74 55.67 68.00 -12.33 98.1 H 58.62 (AV) 8.4 0.61 26.75 -17.74 40.88 48.00 -7.12 -- H -- -- -- -- -- -- -- -- 98.1 V 75.37（PK） 8.4 0.61 26.75 -17.74 57.63 68.00 -10.37 98.1 V 59.08 (AV) 8.4 0.61 26.75 -17.74 41.34 48.00 -6.66 -- V -- -- -- -- -- -- -- -- FCC ID: WDS-T01 Page 17 of 30

Report No.:STE110613478 Channel High(107.9MHZ) Fre. Plority Reading Antenna Cable Amplifier Correct Measure Result Limit Margin dBuV Factor Loss Gain Factor dBuV/m dBuV/m dB MHz H/V dB dB dB dB 107.9 H 72.74（PK） 10.9 0.68 26.65 -15.07 57.67 68.00 -10.33 107.9 H 54.96 (AV) 10.9 0.68 26.65 -15.07 39.89 48.00 -8.11 -- H -- -- -- -- -- -- -- -- H 107.9 V 73.86（PK） 10.9 0.68 26.65 -15.07 58.79 68.00 -9.21 107.9 V 55.49 (AV) 10.9 0.68 26.65 -15.07 40.42 48.00 -7.58 -- V -- -- -- -- -- -- -- -- V Notes: --Means other frequency and mode comply with standard requirements and at least have 20dB margin. Correct Factor=Cable Loss+Antenna Factor-Amplifier Gain Measurement Result=Reading + Correct Factor Margin=Measurement Result-Limit FCC ID: WDS-T01 Page 18 of 30

Report No.:STE110613478 7 Bandwidth Test 7.1 Limit for Bandwidth The occupied bandwidth shall not exceed 200 KHZ 7.2 Method of measurement a) The bandwidth is measured at an amplitude level reduced 20dB from the reference level. The reference level is the level of the highest amplitude signal observed from the transmitter at the fundamental frequency. Once the reference level is established, the equipment is conditioned with typical modulating signal to produce the worst-case (i.e. the widest) bandwidth. b) The test receiver RBW set 10KHZ,VBW set 30KHZ 7.3 Test Setup same as section 6.2 7.4 Test Results 88.1MHZ bandwidth test plot FCC ID: WDS-T01 Page 19 of 30

Report No.:STE110613478 98.1MHZ bandwidth test plot 107.9MHZ bandwidth test plot FCC ID: WDS-T01 Page 20 of 30

Report No.:STE110613478 8 Band Edge Test 8.1 Test Limit Please see the part 15.239a 8.2 Test Procedure a) Put the EUT on a 0.8m high table,power on the EUT. Emissions were scanned and measured rotating the EUT to 360 degrees,Find the maximum Emission b) Turning to Low and High frequency,then reduced 20dB from the reference level. The reference level is the level of the highest amplitude signal observed from the transmitter at the fundamental frequency. c) Check the spurious emissions out of band. d) RBW,VBW Setting, please see the following test plot. 8.3 Test Results Pass Detailed information, please see the following page. FCC ID: WDS-T01 Page 21 of 30

Report No.:STE110613478 88.1MHZ Test Plot 107.9MHZ Test Plot FCC ID: WDS-T01 Page 22 of 30

Report No.:STE110613478 9 Antenna Requirement 9.1 Standard requirement An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 9.2 Result The device is integral antenna, it comply with the standard requirement. FCC ID: WDS-T01 Page 23 of 30

Report No.:STE110613478 10 Photographs of Test Setup Photographs-Radiated Emission Test Setup in Chamber FCC ID: WDS-T01 Page 24 of 30

Report No.:STE110613478 Photographs-Conducted Emission Test Setup FCC ID: WDS-T01 Page 25 of 30

Report No.:STE110613478 11 Photographs of EUT Figure 1 Photo of EUT Front View [ ] Rear View [ ] Full View [√] Bottom View[ ] Left View [ ] Right View [ ] Internal View [ ] Figure 2 Photo of EUT Front View [ ] Rear View [ ] Top View [√] Bottom View[ ] Left View [ ] Right View [ ] Internal View [ ] FCC ID: WDS-T01 Page 26 of 30

Report No.:STE110613478 Figure 3 Photo of EUT Front View [ ] Rear View [ ] Top View [ ] Bottom View[√] Left View [ ] Right View [ ] Internal View [ ] Figure 4 Photo of EUT Front View [√] Rear View [ ] Top View [ ] Bottom View[ ] Left View [ ] Right View [ ] Internal View [ ] FCC ID: WDS-T01 Page 27 of 30

Report No.:STE110613478 Figure 5 Photo of EUT Front View [ ] Rear View [ ] Top View [ ] Bottom View[ ] Left View [√] Right View [ ] Internal View [ ] Figure 6 Photo of EUT Front View [ ] Rear View [√] Top View [ ] Bottom View[ ] Left View [ ] Right View [ ] Internal View [ ] FCC ID: WDS-T01 Page 28 of 30

Report No.:STE110613478 Figure 7 Photo of EUT Front View [ ] Rear View [ ] Top View [ ] Bottom View[ ] Left View [ ] Right View [√] Internal View [ ] Figure 8 Photo of EUT Front View [ ] Rear View [ ] Top View [ ] Bottom View[ ] Left View [ ] Right View [ ] Internal View [√] FCC ID: WDS-T01 Page 29 of 30

Report No.:STE110613478 Figure 9 Photo of EUT Front View [ ] Rear View [ ] Top View [ ] Bottom View[ ] Left View [ ] Right View [ ] Internal View [√] Figure 10 Photo of EUT Front View [ ] Rear View [ ] Top View [ ] Bottom View[ ] Left View [ ] Right View [ ] Internal View [√] ------- THE END OF REPORT------- FCC ID: WDS-T01 Page 30 of 30


Document Created: 2019-06-23 15:41:58
Document Modified: 2019-06-23 15:41:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC