Test Reoprt

FCC ID: V7TN80

Test Report

Download: PDF
FCCID_1937330

FCC PART 15B, CLASS B TEST REPORT For SHENZHEN TENDA TECHNOLOGY CO.,LTD. Tenda Industrial Park, No. 34-1, Shilong Rd., Shiyan Town, Bao'an District, Shenzhen, P.R.China FCC ID: V7TN80 Product Type: Report Type: Wireless N900 Concurrent Dual-Band Original Report Gigabit Router Test Engineer: Leon Chen Report Number: R2DG130314004-00A Report Date: 2013-03-29 Ivan Cao Reviewed By: RF Leader Test Laboratory: Bay Area Compliance Laboratories Corp. (Dongguan) No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and shall be marked with an asterisk “★” (Rev.2)

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A TABLE OF CONTENTS GENERAL INFORMATION .......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE ...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................3 TEST FACILITY .............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 JUSTIFICATION .............................................................................................................................................................5 EUT EXERCISE SOFTWARE ..........................................................................................................................................5 EQUIPMENT MODIFICATIONS .......................................................................................................................................5 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................................5 EXTERNAL CABLE........................................................................................................................................................5 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 FCC §15.107 – AC LINE CONDUCTED EMISSIONS .............................................................................................8 MEASUREMENT UNCERTAINTY ....................................................................................................................................8 EUT SETUP ..................................................................................................................................................................8 EMI TEST RECEIVER SETUP .........................................................................................................................................9 TEST PROCEDURE ........................................................................................................................................................9 CORRECTED AMPLITUDE & MARGIN CALCULATION ...................................................................................................9 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................10 TEST RESULTS SUMMARY ..........................................................................................................................................10 TEST DATA ................................................................................................................................................................10 FCC §15.109 - RADIATED EMISSIONS .................................................................................................................13 MEASUREMENT UNCERTAINTY ..................................................................................................................................13 EUT SETUP ................................................................................................................................................................13 EMI TEST RECEIVER SETUP .......................................................................................................................................14 TEST PROCEDURE ......................................................................................................................................................14 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................15 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................15 TEST RESULTS SUMMARY ..........................................................................................................................................15 TEST DATA ................................................................................................................................................................15 FCC Part15B, Class B Page 2 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A GENERAL INFORMATION Product Description for Equipment under Test (EUT) The SHENZHEN TENDA TECHNOLOGY CO.,LTD.’s product, model number: N80 (FCC ID: V7TN80) or ("EUT”) in this report is Wireless N900 Concurrent Dual-Band Gigabit Router, which was measured approximately: 21.6 cm (L) x 15.6 cm (W) x 3.9 cm (H), rated input voltage: DC 12V from adapter. The highest operating frequency is 500MHz. Adapter information: Honor Model: ADS-40FSG-12 12030GPCU Input: AC 100-240V, 50/60Hz, Max.1.0A Output: DC 12V, 2.5A * All measurement and test data in this report was gathered from production sample serial number: 130314004 (Assigned by BACL, Dongguan). The EUT was received on 2013-03-15. Objective This report is prepared on behalf of SHENZHEN TENDA TECHNOLOGY CO.,LTD. in accordance with Part 2, Subpart J, Part 15, Subparts A and B of the Federal Communications Commission rules. The objective of the manufacturer is to determine compliance with FCC Part 15B, Class B. Related Submittal(s)/Grant(s) FCC Part 15C DTS submissions with FCC ID: V7TN80. FCC Part 15E NII submissions with FCC ID: V7TN80. FCC Part15B, Class B Page 3 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Dongguan) to collect test data is located on the No.69 Pulongcun, Puxinhu Industrial Zone, Tangxia, Dongguan, Guangdong, China Test site at Bay Area Compliance Laboratories Corp. (Dongguan) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 02, 2012. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4- 2003. The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: 273710. The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratories Corp. (Dongguan) is an ISO/IEC 17025 accredited laboratory, and is accredited by National Voluntary Laboratory Accredited Program (Lab Code 500069-0). The current scope of accreditations can be found at http://ts.nist.gov/standards/scopes/5000690.htm FCC Part15B, Class B Page 4 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A SYSTEM TEST CONFIGURATION Justification The system was configured for testing in a typical fashion (as normally used by a typical user). EUT Exercise Software The software ‘Broadcom MTool 2.0.0.3’ was used for testing, which was provided by manufacturer. Equipment Modifications No modification was made to the EUT. Support Equipment List and Details Manufacturer Description Model Serial Number HP Printer C3941A JPTVOB2337 SAST Modem AEM-2100 0293 DELL Keyboard L100 CNORH656658907BL05DC DELL Laptop PP11L N/A Kinston Flash Disk 4G / DELL PC GX620 / External Cable Cable Description Length (m) From Port To Shielded Detachable Printer Cable 1.2 Parallel Port of Laptop Printer Shielded Detachable Serial Cable 1.2 Serial Port of Laptop Modem Shielded Detachable Keyboard Cable 1.5 Keyboard Port of Laptop Keyboard RJ 45 Cable 1.0 Laptop EUT RJ45 Cable*4 10 EUT PC FCC Part15B, Class B Page 5 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Block Diagram of Test Setup PC Flash L ISN 2 D isk L ISN 1 M odem 10cm Printer 10cm L aptop 10cm EUT 10cm A dapter R eceptacle 1.0 Meter N on-C onductive T able 80 cm above G round Plane K eyboard 1.5 M eter FCC Part15B, Class B Page 6 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A SUMMARY OF TEST RESULTS FCC Rules Description of Test Results §15.107 AC Line Conducted Emissions Compliance §15.109 Radiated Emissions Compliance FCC Part15B, Class B Page 7 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A FCC §15.107 – AC LINE CONDUCTED EMISSIONS Measurement Uncertainty Compliance or non- compliance with a disturbance limit shall be determined in the following manner： If Ulab is less than or equal to Ucispr of Table 1, then: –compliance is deemed to occur if no measured disturbance level exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level exceeds the disturbance limit. If Ulab is greater than Ucispr of Table 1, then: –compliance is deemed to occur if no measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit. Based on CISPR 16-4-2: 2011, measurement uncertainty of conducted disturbance at mains port using AMN at Bay Area Compliance Laboratories Corp. (Dongguan) is 3.46 dB (150 kHz to 30 MHz). Table 1 – Values of Ucispr Measurement Ucispr Conducted disturbance at mains port using AMN (150 kHz to 30 MHz) 3.4 dB EUT Setup The setup of EUT is according with per ANSI C63.4-2003 measurement procedure. The specification used was with the FCC Part 15.107 Class B limits. FCC Part15B, Class B Page 8 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A The adapter was connected to a 120 VAC/60 Hz power source. EMI Test Receiver Setup The EMI test receiver was set to investigate the spectrum from 150 kHz to 30 MHz. During the conducted emission test, the EMI test receiver was set with the following configurations: Frequency Range IF B/W 150 kHz – 30 MHz 9 kHz Test Procedure During the conducted emission test, the adapter was connected to the outlet of the first LISN and the other support equipments were connected to the outlet of the second LISN. Maximizing procedure was performed on the six (6) highest emissions of the EUT. All data was recorded in the Quasi-peak and average detection mode. Corrected Amplitude & Margin Calculation The basic equation is as follows: VC = VR + AC + VDF Cf = AC + VDF Herein, VC (cord. Reading): corrected voltage amplitude VR: reading voltage amplitude Ac: attenuation caused by cable loss VDF: voltage division factor of AMN Cf: Correction Factor The “Margin” column of the following data tables indicates the degree of compliance within the applicable limit. For example, a margin of 7dB means the emission is 7dB below the maximum limit. The equation for margin calculation is as follows: Margin = Limit – Corrected Amplitude FCC Part15B, Class B Page 9 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date R&S EMI Test Receiver ESCS 30 830245/006 2012-11-29 2013-11-28 R&S LISN1 ESH3-Z5 843331/015 2012-09-17 2013-09-16 R&S LISN2 ESH3-Z5 100113 2012-11-29 2013-11-28 BACL Test Software BACL-EMC V1.0-2010 N/A N/A * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to National Primary Standards and International System of Units (SI). Test Results Summary According to the recorded data in following table, the EUT complied with the FCC Part 15.107, with the worst margin reading of: 12.28 dB at 0.260 MHz in the Neutral conducted mode. Test Data Environmental Conditions Temperature: 26.1 °C Relative Humidity: 61 % ATM Pressure: 100.4 kPa The testing was performed by Leon Chen on 2013-03-28. FCC Part15B, Class B Page 10 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Test mode: operating 120 V, 60 Hz, Line: Cord. Correction Frequency Limit Margin Detector Reading Factor (MHz) (dBμV) (dB) (PK/AV/QP) (dBμV) (dB) 0.170 49.08 1.03 65.43 16.35 QP 0.170 35.92 1.03 55.43 19.51 AV 0.250 37.31 0.89 63.14 25.83 QP 0.250 25.57 0.89 53.14 27.57 AV 0.540 31.41 0.51 56.00 24.59 QP 0.540 27.55 0.51 46.00 18.45 AV 1.360 31.22 0.33 56.00 24.78 QP 1.360 25.20 0.33 46.00 20.80 AV 2.230 30.37 0.37 56.00 25.63 QP 2.220 24.76 0.37 46.00 21.24 AV 3.470 28.95 0.41 56.00 27.05 QP 3.470 22.40 0.41 46.00 23.60 AV FCC Part15B, Class B Page 11 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A 120 V, 60 Hz, Neutral: Cord. Correction Frequency Limit Margin Detector Reading Factor (MHz) (dBμV) (dB) (PK/AV/QP) (dBμV) (dB) 0.170 49.37 1.74 65.43 16.06 QP 0.170 37.38 1.74 55.43 18.05 AV 0.260 44.13 1.28 62.86 18.73 QP 0.260 40.58 1.28 52.86 12.28 AV 0.300 42.58 1.07 61.71 19.13 QP 0.300 35.28 1.07 51.71 16.43 AV 0.610 34.44 0.48 56.00 21.56 QP 0.610 29.23 0.48 46.00 16.77 AV 1.310 32.67 0.24 56.00 23.33 QP 1.310 27.06 0.24 46.00 18.94 AV 2.320 31.04 0.28 56.00 24.96 QP 2.320 23.86 0.28 46.00 22.14 AV FCC Part15B, Class B Page 12 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A FCC §15.109 - RADIATED EMISSIONS Measurement Uncertainty Compliance or non- compliance with a disturbance limit shall be determined in the following manner： If Ulab is less than or equal to Ucispr of Table 2, then: –compliance is deemed to occur if no measured disturbance level exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level exceeds the disturbance limit. If Ulab is greater than Ucispr of Table 1, then: –compliance is deemed to occur if no measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit; –non - compliance is deemed to occur if any measured disturbance level, increased by (Ulab − Ucispr), exceeds the disturbance limit. Based on CISPR 16-4-2: 2011, measurement uncertainty of radiated emission at a distance of 3m at Bay Area Compliance Laboratories Corp. (Dongguan) is: 30M~200MHz: 5.0 dB 200M~1GHz: 6.2 dB 1G~6GHz: 4.45 dB 6G~18GHz: 5.23 dB Table 2 – Values of Ucispr Measurement Ucispr Radiated disturbance (electric field strength at an OATS or in a SAC) (30 MHz to 1000 MHz) 6.3 dB Radiated disturbance (electric field strength in a FAR) (1 GHz to 6 GHz) 5.2 dB Radiated disturbance (electric field strength in a FAR) (6 GHz to 18 GHz) 5.5 dB EUT Setup Below 1 GHz: FCC Part15B, Class B Page 13 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Above 1 G: The radiated emission tests were performed in the 3 meters chamber test site, using the setup accordance with the ANSI C63.4-2003. The specification used was the FCC Part 15.109, Class B limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The adapter connected to a 120 VAC/60 Hz power source. EMI Test Receiver Setup According to FCC 15.33 requirements, the system was measured from 30 MHz to 6 GHz. During the radiated emission test, the EMI test receiver was set with the following configurations: Frequency Range RBW Video B/W Detector 30 MHz – 1000 MHz 120 kHz 300 kHz QP Above 1 GHz 1MHz 3 MHz Peak Above 1 GHz 1MHz 10 Hz Ave Test Procedure For the radiated emissions test, the adapter was connected to the first AC floor outlet and the other support equipments were connected to the second AC floor outlet. Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. The data was recorded in Quasi-peak detection mode for 30 MHz to 1 GHz, Peak and average detection mode above 1 GHz. FCC Part15B, Class B Page 14 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Loss and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Loss + Cable Loss - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit – Corrected Amplitude Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date EMI TEST R&S ESCI 100224 2012-5-14 2013-5-13 RECIEVER Sunol Antenna JB3 A060611-1 2012-9-6 2013-9-5 Sciences HP HP AMPLIFIER 8447E 2434A02181 N/A N/A R&S Spectrum analyzer FSEM 30 849016/001 2012-9-4 2013-9-3 ETS LINDGREN horn antenna 3115 000 527 35 2012-9-6 2013-9-5 Mini-Circuit Amplifier ZVA-213-S+ 054201245 N/A N/A Rohde & Schwarz Spectrum Analyzer FSP38 100478 2012-5-14 2013-5-13 * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to National Primary Standards and International System of Units (SI). Test Results Summary According to the data in the following table, the EUT complied with the FCC §15.109, Class B, with the worst margin reading of: 3.17 dB at 79.4700 MHz in the Vertical polarization below 1GHz Test Data Environmental Conditions Temperature: 24.8°C Relative Humidity: 68 % ATM Pressure: 100.8 kPa The testing was performed by Leon Chen on 2013-03-27 Test mode: operating FCC Part15B, Class B Page 15 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Below 1G: Horizontal: Receiver Detector Correction Cord. Frequency Limit Margin Reading (PK/QP/Ave Factor Amp. (MHz) (dBuV/m) (dB) (dBuV/m) ) (dB) (dBuV/m) 250.1900 42.57 QP -8.18 34.39 46.00 11.61 300.6300 45.67 QP -6.17 39.50 46.00 6.50 375.3200 37.00 QP -4.50 32.50 46.00 13.50 500.4500 36.75 QP -2.27 34.48 46.00 11.52 625.5800 39.88 QP -0.50 39.38 46.00 6.62 891.3600 37.54 QP 2.85 40.39 46.00 5.61* *Within measurement uncertainty! FCC Part15B, Class B Page 16 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Vertical: Receiver Detector Correction Cord. Frequency Limit Margin Reading (PK/QP/Ave Factor Amp. (MHz) (dBuV/m) (dB) (dBuV/m) ) (dB) (dBuV/m) 79.4700 49.43 QP -12.60 36.83 40.00 3.17* 304.5100 43.08 QP -6.03 37.05 46.00 8.95 375.3200 41.02 QP -4.50 36.52 46.00 9.48 500.4500 37.96 QP -2.27 35.69 46.00 10.31 625.5800 42.07 QP -0.50 41.57 46.00 4.43* 875.8400 39.51 QP 2.57 42.08 46.00 3.92* *Within measurement uncertainty! FCC Part15B, Class B Page 17 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Above 1G: Horizontal: Receiver Detector Correction Cord. Frequency Limit Margin Reading (PK/QP/Ave Factor Amp. (MHz) (dBuV/m) (dB) (dBuV/m) ) (dB) (dBuV/m) 2082.164 49.49 peak -2.37 47.12 74.00 26.88 2082.164 38.84 AVG -2.37 36.47 54.00 17.53 2222.445 48.86 peak -2.07 46.79 74.00 27.21 2222.445 37.39 AVG -2.07 35.32 54.00 18.68 2382.765 52.54 peak -1.54 51.00 74.00 23.00 2382.765 41.10 AVG -1.54 39.56 54.00 14.44 FCC Part15B, Class B Page 18 of 19

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: R2DG130314004-00A Vertical: Receiver Correction Cord. Frequency Detector Limit Margin Reading Factor Amp. (MHz) (PK/QP/Ave) (dBuV/m) (dB) (dBuV/m) (dB) (dBuV/m) 1951.904 47.39 peak -2.60 44.79 74.00 29.21 1951.904 38.27 AVG -2.60 35.67 54.00 18.33 2082.164 49.39 peak -2.37 47.02 74.00 26.98 2082.164 39.31 AVG -2.37 36.94 54.00 17.06 2923.848 43.68 peak -0.43 43.25 74.00 30.75 2923.848 34.71 AVG -0.43 34.28 54.00 19.72 ***** END OF REPORT ***** FCC Part15B, Class B Page 19 of 19


Document Created: 2013-04-09 10:46:00
Document Modified: 2013-04-09 10:46:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC