HAC TCoil report

FCC ID: V65S1360

Test Report

Download: PDF
FCCID_2006271

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 Hearing Aid Compatibility (HAC) T-Coil FCC 47 CFR Part 20.19 Test Report For Kyocera Corporation c/o Kyocera Communications, Inc. Product: CDMA Mobile Phone Model: S1360 © 2013 Comptest Services LLC Page 1 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 TABLE OF CONTENTS 1 SUMMARY OF TESTING .................................................................................................................. 4 2 EQUIPMENT UNDER TEST INFORMATION .................................................................................... 5 3 TEST CONDITIONS .......................................................................................................................... 6 3.1 Test Facilities ............................................................................................................................. 6 3.2 Ambient Conditions .................................................................................................................... 6 3.3 RF characteristics of the test site ................................................................................................ 6 3.4 Ambient Noise of the test site ..................................................................................................... 6 3.5 Test Signal, Frequencies and Output Power............................................................................... 7 3.6 EUT Operating Conditions .......................................................................................................... 8 4 DESCRIPTION OF TEST EQUIPMENT ............................................................................................ 9 4.1 Test Equipment Used ................................................................................................................. 9 4.2 T-Coil Measurement System .................................................................................................... 10 4.3 Audio Magnetic Probe .............................................................................................................. 11 4.4 Audio Magnetic Measuring Instrument (AMMI) ......................................................................... 11 4.5 Audio Magnetic Calibration Coil (AMCC) .................................................................................. 11 5 SYSTEM VALIDATION & CALIBRATION ...................................................................................... 12 5.1 Input Channel Calibration ......................................................................................................... 12 5.2 Probe Calibration ...................................................................................................................... 13 5.3 Reference Input Level .............................................................................................................. 14 6 DESCRIPTION OF TEST PROCEDURE......................................................................................... 15 6.1 Test Positions ........................................................................................................................... 16 6.2 Audio Signals ........................................................................................................................... 16 6.3 Scan Procedures ...................................................................................................................... 18 7 DESCRIPTION OF TEST PROCEDURE......................................................................................... 19 8 T-COIL REQUIREMENTS AND CATEGORY ................................................................................. 20 8.1 RF Emissions ........................................................................................................................... 20 8.2 Axial Field Intensity................................................................................................................... 20 8.3 Signal Quality ........................................................................................................................... 20 8.4 Frequency Response ............................................................................................................... 21 9 T-COIL TEST RESULTS ................................................................................................................. 22 9.1 Field Strength and Signal Quality ............................................................................................. 22 9.2 Frequency Response ............................................................................................................... 23 10 Appendix A2: Ambient Noise Plots, 1900 MHz ........................................................................ 25 11 Appendix B: System Calibration Results ................................................................................. 26 12 Appendix C: ABM and SNR Test Results/Plots ....................................................................... 26 13 Appendix D: Probe Calibration Certificate ............................................................................... 26 14 Appendix E: Photo Test Setup .................................................................................................. 26 © 2013 Comptest Services LLC Page 2 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 ATTESTATION The tested device complies with the requirements in respect of all parameters subject to the test. The test results and statements relate only to the items tested. The test equipment used was suitable for the tests performed and within manufacturer’s published specifications and operating parameters. The test methods were consistent with the methods described in the relevant standards. Product: CDMA Mobile Phone with Bluetooth Model #: S1360 FCC ID: V65S1360 Tested in accordance with: FCC 47 CFR Part 20.19 ANSI C63.19-2007 Test Requested by: KYOCERA Corporation C/o KYOCERA Communications, Inc. 8611 Balboa Ave. San Diego, CA 92123 United States Test performed by: Comptest Services LLC Date of Test: May 03, 2013 Responsible Engineer Reviewed and approved by: Benjamin Nguyen Kelly Hill Benjamin Nguyen Kelly Hill Test Engineer Quality Manager © 2013 Comptest Services LLC Page 3 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 1 SUMMARY OF TESTING ANSI C63.19 (2007) Section 6 T-coil Mode Test Test Results T-Rating Verdict Min. Axial Field Strength, dB A/m 1.71 -- Pass CDMA Min. Radial Field Strength, dB A/m -8.00 -- Pass 1900- BC1 Min. Signal Quality (ABM1/ABM2), dB 50.01 4 Pass Frequency Response @ Axial position -- -- Pass Overall T-Rating: T4 M-Rating*: M4 HAC Category Rating: M4, T4 * M-rating obtained from HAC RF report. © 2013 Comptest Services LLC Page 4 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 2 EQUIPMENT UNDER TEST INFORMATION Product: CDMA Mobile Phone with Bluetooth FCC ID: V65S1360 Model Number: S1360 EUT Serial Number: 268435457816732379 Type: [ ] Identical Prototype, [X] Pre-Production, [ ] Production Device Category: Portable RF Exposure Environment: General Population / Uncontrolled Antenna: Internal Detachable: No External Input: Audio/Digital Data Quantity: Quantity production is planned Mode: CDMA 1x Band: BC-1 TX Frequency (MHz): 1851.25 - 1908.75 © 2013 Comptest Services LLC Page 5 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 3 TEST CONDITIONS 3.1 Test Facilities The test sites and measurement facilities used to collect data are located at 8611 Balboa Avenue, San Diego, CA 92123, USA 3.2 Ambient Conditions All tests were performed under the following environmental conditions: Ambient Temperature: 23 ± 2 Degrees C Relative Humidity (RH): 0% <RH < 80% Atmospheric Pressure: 101.3kPa + 10 to –5 kPa 3.3 RF characteristics of the test site All HAC measurements were performed inside a shielded room that provide isolation from external EM fields, with the RF ambient at least 20 dB below the intended measurement limits. 3.4 Ambient Noise of the test site All HAC measurements were performed inside a shielded room that provide isolation from external EM fields, with the RF ambient at least 20 dB below the intended measurement limits. The test site’s ambient magnetic level were determined and found to be at least 10dB below the measurement data ABM2, unless a very low level of AMB2. Measurement of the ambient level was performed for each probe orientation and results are shown in Appendix B. © 2013 Comptest Services LLC Page 6 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 3.5 Test Signal, Frequencies and Output Power The device supports CDMA2000 in 1X (Phase I, Protocol revision 6) mode. CDMA2000 1X includes TIA/EIA-95B as a subset and was approved for publishing in July 1999. It provides voice and data capabilities within a standard 1.25 MHz CDMA channel. This RF bandwidth is identical to the legacy IS-95 B system standard. Maximum average conducted powers were measured to ensure worst case power configuration was tested: CONFIGURATION CONDUCTED POWER (dBm) (Full Rate) CDMA 1900 Ch Ch Ch 25 600 1175 RC1 24.70 24.74 24.75 SO3 RC3 24.77 24.76 24.77 RC2 24.75 24.74 24.72 SO17 RC54 24.72 24.72 24.70 In all operating modes, the phone was set to rate maximum RF power level and the measurements were performed on low, mid and high channels. The measurement system measures power drift during HAC testing by comparing E/H-field in the same location at the beginning and at the end of measurement. These records were used to monitor stability of power output during tests. Conducted RF power measurements were also performed before and after each HAC measurements to confirm the output power. During tests, the EUT was put in in-call mode and controlled by a CDMA simulator to generate the required signal and power: Protocol: 6 (IS-2000) Radio Configuration: 3 Power Control: All Up Bits Service Option: 3 Vocoder: 8K Enhanced (low) Data Rate: Full © 2013 Comptest Services LLC Page 7 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 3.6 EUT Operating Conditions The EUT was tested with the follow configurations and conditions, if applicable: Voice Over IP Simultaneous Band C63.19 Mode Type Transport Transmissions (MHz) (Tested) (Data) (Not Tested) CDMA 1x 1900 Voice N/A Yes: BT Yes CDMA EVDO Rev0, A Bluetooth 2450 Data N/A Yes: CDMA N/A WiFi X Fully charged standard battery as supplied with the handset Closed configurations at ear use position1 Both retracted and extended antenna positions X Back-light always ON X LCD Contrast High X Receiver volume setting at maximum X Microphone muted Note 1: This device has only one configuration for ear usage © 2013 Comptest Services LLC Page 8 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 4 DESCRIPTION OF TEST EQUIPMENT 4.1 Test Equipment Used Below is a list of the calibrated equipment used for the measurements. The calibration certificates of Probe and Helmholtz Coil are attached in Appendix A. Description Manufacturer Model Serial Cal Due Number Number Date Power Meter Giga-tronics 8541C 1831306 05/16/13 Radio Communication Tester Rohde & Schwarz CMU200 101328 05/16/13 Data Acquisition Speag DAE4 527 07/30/13 Audio Band Magnetic Probe Speag AM1DV2 1045 09/20/13 Audio Band Magnetic Speag AMMI 1035 N/A Measuring Instrument Helmholtz Coil Speag AMCC 1001 N/A Test Arch Speag HAC 1015 N/A © 2013 Comptest Services LLC Page 9 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 4.2 T-Coil Measurement System The measurements were performed with Dasy4 automated near-field scanning system comprised of high precision robot, robot controller, computer, Magnetic probe, probe alignment sensor, non- conductive phone positioner, Test Arch and software extension. Figure 5.2 show the setup and cabling. The overall expanded uncertainty (K=2) of the measurement system is 12.3%. The measurement uncertainty budget is given in section 6. Figure 4.2a T-Coil setup with Helmholtz Coil Figure 4.2b Setup Cabling © 2013 Comptest Services LLC Page 10 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 4.3 Audio Magnetic Probe Model:  AM1D Application:  Active single sensor probe for both axial and radial measurement scans Construction:  Fully RF shielded  Rounded tip of 6 mm diameter incorporating a pickup coil with its center offset 3mm from the tip and the sides  Compatible with DAE, with adapted probe cup Frequency  ± 0.5dB of ideal differentiator from 100 Hz to 10 kHz Response: Linearity:  < 0.1 dB from 5 dB below limitation to 16 dB above noise level Dynamic Range:  Max 21 dB A/m @ 1 kHz, Noise level typ. –70 dB A/m @ 1kHz, ABM2 typ. –60 dB A/m Sensitivity:  Typ. -24 dBV / A./m @ 1kHz at probe output RF Shielding:  Immunity to AM (1 kHz, 80%) modulation RF signal 4.4 Audio Magnetic Measuring Instrument (AMMI) Model:  AMMI Application: AMMI is a desktop 19-inch unit containing a sampling unit, a waveform generator for test and calibration signals and a USB interface. Connection: Front connectors  Audio Out - audio signal to the base station simulator  Coil Out - test and calibration signal to the AMCC  Coil In - monitor signal from the AMCC BNO connector  Probe In - probe signal 4.5 Audio Magnetic Calibration Coil (AMCC) Model:  AMCC Application: The Audio Magnetic Calibration coil is a Helmholtz Coil designed according to ANSI C63.19-2006 section D.9, for calibration of the AM1D probe. The two horizontal coils generate a homogeneous magnetic field in the z direction. The DC input resistance is adjusted to approximately 50 Ohm by a series resistor, and a shunt resistor of 10 Ohm allows monitoring the current with a scale of 1:10. Connection:  Coil In  Coil Monitor © 2013 Comptest Services LLC Page 11 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 5 SYSTEM VALIDATION & CALIBRATION At the beginning of the HAC T-coil measurement, a 3-phase calibration was performed per Speag instruction to ensure accurate measurement of the voltages and ABM field. Reference input level was also validated and calibrated per C63.19. 5.1 Input Channel Calibration Phase 1: The AMMI audio output was switched off, and a 200 mV_pp symmetric rectangular signal of 1 kHz was generated and internally connected directly to both channels of the sampling unit (coil in, probe in). Phase 2: The AMMI audio output was off, and a 20 mV_pp symmetric 100 Hz signal was internally connected. The signals during phases 1 and 2 were available at the output on the rear panel of the AMMI. The output must however not be loaded in order not to influence the calibration. After the first two phases, the two input channels were both calibrated for absolute measurements of voltages. The resulting factors were displayed above the multimeter window. After phases 1 and 2, the input channels were calibrated to measure exact voltages. © 2013 Comptest Services LLC Page 12 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 5.2 Probe Calibration Phase 3: a multisine signal covering each third-octave band from 50 Hz to 5 kHz was generated and applied to both audio outputs. The probe was positioned in the center of the AMCC (user point “coil center”) and aligned in the z-direction, the field orientation of the AMCC. The Coil In channel was measuring the voltage over the AMCC internal shunt, which was proportional to the magnetic field in the AMCC. At the same time, the probe in channel samples the amplified signal picked up by the probe coil. The ratio of the two voltages – in each third-octave filter – leads to the calibration factor of the probe over the frequency band of interest for the spectral representation. The Coil signal is scaled in dBV, and the Probe signal is normalized to show dBV at a frequency of 1 kHz. The sensitivity is the ratio at 1 kHz. The frequency response of the probe (subject to an integrator) can be calculated from the difference of the two curves. The calibration result using a AM1DV2 probe is shown in Appendix B. The internal calibration factors of the coil and probe channel are listed. The graphics represent the values (applying the calibration factors from the previous steps) for the probe and coil channel in dB V for each third-octave filter from 100 Hz to 5 kHz. These values are interconnected with a blue line for the probe and a green line for the coil channel. The probe sensitivity in V / (A/m) at 1 kHz is calculated from the values in the chart. -20 dBV in the coil channel corresponds approx. to 1 A/m. The lines are typically horizontal. Deviations around 160 Hz typically result from power line interference, and the slight decay at the higher frequency is a result of the channel frequency response. Calibration Factors Measured Value Probe Sensitivity, V/(A/m) 0.0655 Probe calibration factor, V 1.1292 Coil calibration factor, V 2.3517 © 2013 Comptest Services LLC Page 13 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 5.3 Reference Input Level ANSI C63.19 requires the use of reference input level of –18dBm0 that correlate to a normal speech input level for CDMA air interface. In order to create the correct level the CMU200 audio codec and the AMMI output were calibrated. 5.3.1 CMU200 Audio Codec Calibration To determine the correct input level, the Encoder/Decorder of the CMU200 base station simulator was calibrated for measured full-scale input voltage level. The CMU200 0dBm0 input reference was determined utilizing the build-in functions of “Decoder Cal” and “Encoder Cal”. CMU200 S/N Modulation Ref. I/P Level Target Level 101328 CDMA -18dBm0 -20.49 Table 5.3a CMU200 Target Level 5.3.2 AMMI Signal Verification Verification of AMMI output level was performed within 24 hours of the compliance measurement. The measured results are shown in Table 5.3b Date Signal Measured AMMI Target Reference Delta Output Input (dBm0) (dBm0) (dB) 1KHz -20.49 -20.47 -0.02 5/3/2013 48k_voice_1kHz -20.49 -20.48 -0.01 48k_voice_300_3000 -20.51 -20.47 -0.04 Table 5.3b Measured Output Level © 2013 Comptest Services LLC Page 14 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 6 DESCRIPTION OF TEST PROCEDURE The device was positioned and setup according to ANSI C63.19-2006. Figure 6.0 shows the T-Coil Signal measurement flowchart:  Confirm calibration of Test Equipment  Configure and validate test setup  Establish WD reference level  Find measurement locations  Position and orient probe  Measure desired audio band signal strength  Measure undesired audio band signal strength   Calculate signal strength  Calculate signal quality  Measure frequency response (axial) All 3 locations measured? No Yes Intensity and response compliant ? No Yes Determine and record signal quality category Done Figure 6.0 T-Coil measurement flowchart © 2013 Comptest Services LLC Page 15 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 6.1 Test Positions The device was placed on a non-conductive phone positioner under the Test Arch. The acoustic output of the EUT was aligned with the center point of the area formed by the dielectric wire and the middle bar of the arch’s top frame. Please refer to Appendix E for the test setup photos. 6.2 Audio Signals During tests signal was fed to the EUT via communication Test set. Proper gain setting was used in software to ensure correct signal level fed to communication test set speech input. The following audio signals were pre-defined by DASY4 and used for calibration and measurements: 48k_voice_1kHz_1 s (duration 1 s): This signal is voice like and has been processed to have a narrow bandwidth mainly within the 1 kHz third-octave band and an even shorter duration of 1 second for faster measurement. This signal passes through a large variety of codecs and permits a direct amplitude and signal quality measurement (S/N) without considerable bandwidth compensation. Its spectrum is shown in a practical measurement in Figure 6.2a. Figure 6.2a 1.0 kHz Voice signal spectrum © 2013 Comptest Services LLC Page 16 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 Multisine signal 50 Hz – 5 kHz (duration 10 s): Signal with carrier centered in each third-octave band, as used during the calibration. Suited for frequency response measurements. Peak to RMS ratio: 11.1 dB. 48k_voice_300-3000 (duration 2 s): The signal is voice like and has been processed to have a duration of 2 seconds for fast measurement. At the same time, it has a flat spectrum across all third-octave band filters between 300 Hz to 3 kHz and is vanishing at the beginning and end in order to allow longer measurement sequences without transients. It has bandwidth sufficient for frequency response measurements. The spectrum is shown in a practical measurement in fig. 6.2b. The measurement window length of this signal must be set to a multiple of 2 s in order to integrate over the full voice sample. Peak to RMS ratio: 21.6 dB. Figure 6.2b Broadband signal spectrum © 2013 Comptest Services LLC Page 17 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 6.3 Scan Procedures 6.3.1 Signal Strength and SNR a) A 50mm x 50mm (10mm step) coarse axial scan was performed to search for the “optimal points” and spatial distribution of ABM1. b) Base on the coarse scan results, a 16mm x 16mm (4mm step) point scan in axial, a 24mmx16mm (4mm step) point scan in radial_L, and a 16mmx24mm (4mm step) point scan in radial-T coil orientation were performed for both ABM1and ABM2. 6.3.2 Frequency Response Base on the coarse axial scan results, a point axial scan was performed. © 2013 Comptest Services LLC Page 18 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 7 DESCRIPTION OF TEST PROCEDURE Table 7.1 shows the uncertainty budget for HAC Audio Band Magnetic Field (AMB) assessment according to ANSI C63.19-2006. The budget is valid for the DASY4 system and represents a worst- case analysis. For specific tests and configurations, the uncertainty could be smaller. Uncertainty Description Uncert. Prob. Div. Ci Ci Stand. Stand. Value Dist. (ABM1) (ABM2) Uncert Uncert ( %) (ABM1) (ABM2) (%) (%) PROBE SENSITIVITY Reference level 3.0 N 1.0 1 1 3.0 3.0 AMCC geometry 0.4 R 1.7 1 1 0.2 0.2 AMCC current 0.6 R 1.7 1 1 0.4 0.4 Probe positioning during 0.1 R 1.7 1 1 0.1 0.1 calibration Noise contribution 0.7 R 1.7 0.0143 1 0 0.4 Frequency slope 5.9 R 1.7 1 1 0.3 3.5 PROBE SYSTEM Repeatability / Drift 1.0 R 1.7 1 1 0.6 0.6 Linearity / Dynamic range 0.6 R 1.7 1 1 0.4 0.4 Acoustic noise 1.0 R 1.7 0.1 1 0.1 0.6 Probe angle 2.3 R 1.7 1 1 1.4 1.4 Spectral processing 0.9 R 1.7 1 1 0.5 0.5 Integration time 0.6 N 1.0 1 5 0.6 3.0 Field distribution 0.2 R 1.7 1 1 0.1 0.1 TEST SIGNAL Reference signal spectral 0.6 R 1.7 0 1 0 0.4 response POSITIONING Probe positioning 1.9 R 1.7 1 1 1.1 1.1 Phantom thickness 0.9 R 1.7 1 1 0.5 0.5 DUT positioning 1.9 R 1.7 1 1 1.1 1.1 EXTERNAL CONTRIBUTIONS RF interference 0 R 1.7 1 1 0 0 Test signal variation 2.0 R 1.7 1 1 1.2 1.2 COMBINED UNCERTAINTY Combined Standard Uncertainty (ABM): 4.1 6.1 Extended Standard Uncertainty (k=2) [%]: 8.1 12.3 N: Normal R: Rectangular Table 7.1 Worst-Case uncertainty budget for HAC ABM assessment © 2013 Comptest Services LLC Page 19 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 8 T-COIL REQUIREMENTS AND CATEGORY 8.1 RF Emissions EUT has to fulfill RF emission requirements at the axial measurement location. 8.2 Axial Field Intensity Table 8.2 shows the minimum limits for ABM1 field intensity: Component ABN1 Magnetic Field Condition dB(A/m) Axial (z) ≥-18 1 kHz, in 1/3 octave band filter Radial (x, y) ≥-18 Table 8.2 ABM1 Intensity Requirements 8.3 Signal Quality Table 8.3 provides the signal quality requirement for the intended T-Coil signal from a Wireless Device. The worst Signal Quality of the axial and radial components of the magnetic field was used to determine the T-Coil category. Category Signal Quality (Signal+Noise to Noise) [dB] T1 0 to 10 T2 10 to 20 T3 20 to 30 T4 > 30 AWF=0 Table 8.3 T-coil Signal Quality Categories © 2013 Comptest Services LLC Page 20 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 8.4 Frequency Response The frequency response of the axial component must follow the frequency curve specified in ANSI C63.19-2007 section 7.3.2, over the frequency range 300-3000 Hz (Figure 8.4). Magnetic Field Response (300Hz to 3kHz) for devices with a field £15dB (A/m) at 1 kHz 20.00 -4 dB/Oct. dB relative to value at 1kHz 10.00 +2 dB +2 dB 0.00 -6 dB/Oct. -10.00 +6 dB/Oct. lower limit upper limit -20.00 100.00 1000.00 10000.00 Frequency (Hz) Figure 8.4a Magnetic Field Response (300Hz to 3kHz) for devices with a field 15dB (A/m) at 1 kHz Magnetic Fieldy Response (300Hz to 3kHz) for devices with a field that > -10dB (A/m) at 1 kHz 20.00 dB relative to value at 1kHz -4 dB/Oct. +2 dB 10.00 -2 dB 0.00 -7 dB/Oct. -10.00 6 dB/Oct. lower limit -12 dB/Oct. upper limit -20.00 100.00 1000.00 10000.00 Frequency (Hz) Figure 8.4b Magnetic Field Response (300Hz to 3kHz) for devices with a field that > -15dB (A/m) at 1 kHz © 2013 Comptest Services LLC Page 21 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 9 T-COIL TEST RESULTS 9.1 Field Strength and Signal Quality ANSI C63.19 (2007) Section 6 T-coil Field Strength and Signal Quality Slide Close Band Ch. Probe Ambient ABM1 ABM2 ABM1/ABM2 T- Position Noise dB A/m dB A/m dB Rating dB A/m Axial (z) -52.99 1.99 -52.86 54.85 4 25 Radial_L (x) -55.78 -4.89 -57.08 52.19 4 Radial_T (y) -55.78 -8.00 -58.01 50.01 4 CDMA Axial (z) -52.99 2.18 -52.97 55.15 4 1900- 600 Radial_L (x) -55.78 -6.15 -56.46 50.31 4 BC1 Radial_T (y) -55.78 -7.73 -57.96 50.23 4 Axial (z) -52.99 1.71 -52.89 54.60 4 1175 Radial_L (x) -55.78 -4.98 -55.87 50.89 4 Radial_T (y) -55.78 -7.39 -57.79 50.40 4 Note:  Bold Number = worst case at each frequency band  Data plots are showed in Appendix D © 2013 Comptest Services LLC Page 22 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 9.2 Frequency Response ANSI C63.19 (2007) Section 6 T-coil Frequency Response Mode Probe Position Signal Type Result CDMA 1900 Axial Voice Pass Figure 9.2 show the worst-case frequency response of the axial component of the magnetic field. © 2013 Comptest Services LLC Page 23 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 Figure 9.2a CDMA 1900 BC-1, Frequency Response © 2013 Comptest Services LLC Page 24 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 10 APPENDIX A2: AMBIENT NOISE PLOTS, 1900 MHZ Ambient Noise Spectrum Plot Axial (z) Ambient Noise Spectrum Plot Radial_Longitudinal (x) Ambient Noise Spectrum Plot Radial_Transversal (y) © 2013 Comptest Services LLC Page 25 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.

Applicant: Kyocera FCC ID: V65S1360 Report #: CT-S1360-13-0513-R0 11 APPENDIX B: SYSTEM CALIBRATION RESULTS 12 APPENDIX C: ABM AND SNR TEST RESULTS/PLOTS (See attachment) 13 APPENDIX D: PROBE CALIBRATION CERTIFICATE (See attachment) 14 APPENDIX E: PHOTO TEST SETUP (See attachment) © 2013 Comptest Services LLC Page 26 of 26 HAC T-coil Report This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


Document Created: 2013-05-15 14:56:44
Document Modified: 2013-05-15 14:56:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC