DCD Test Report

FCC ID: V65E6910

Test Report

Download: PDF
FCCID_4038241

FCC Test Report Report No.: RF180821C20-4 FCC ID: V65E6910 Test Model: E6910 Received Date: Aug. 21, 2018 Test Date: Sep. 18, 2018 Issued Date: Sep. 25, 2018 Applicant: Kyocera Corporation c/o Kyocera International, Inc. Address: 8611 Balboa Avenue, San Diego, CA 92123 Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) Test Location (1): No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC Registration / 788550 / TW0003 Designation Number: This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF180821C20-4 Page No. 1 / 25 Report Format Version: 6.1.1

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ........................................................................................................................... 4 2 Summary of Test Results ........................................................................................................................... 5 2.1 Measurement Uncertainty ..................................................................................................................... 5 2.2 Modification Record .............................................................................................................................. 5 3 General Information ................................................................................................................................... 6 3.1 General Description of EUT .................................................................................................................. 6 3.2 Description of Test Modes..................................................................................................................... 7 3.2.1 Test Mode Applicability and Tested Channel Detail .................................................................... 7 3.3 Description of Support Units ................................................................................................................. 8 3.3.1 Configuration of System under Test ........................................................................................... 8 3.4 General Description of Applied Standards ............................................................................................ 8 4 Test Types and Results .............................................................................................................................. 9 4.1 Radiated Emission and Bandedge Measurement ................................................................................ 9 4.1.1 Limits of Radiated Emission and Bandedge Measurement ....................................................... 9 4.1.2 Test Instruments ....................................................................................................................... 10 4.1.3 Test Procedures ......................................................................................................................... 11 4.1.4 Deviation from Test Standard .................................................................................................... 11 4.1.5 Test Setup ................................................................................................................................. 12 4.1.6 EUT Operating Conditions ........................................................................................................ 12 4.1.7 Test Results .............................................................................................................................. 13 4.2 Conducted Emission Measurement .................................................................................................... 19 4.2.1 Limits of Conducted Emission Measurement ........................................................................... 19 4.2.2 Test Instruments ....................................................................................................................... 19 4.2.3 Test Procedures ........................................................................................................................ 20 4.2.4 Deviation from Test Standard ................................................................................................... 21 4.2.5 Test Setup ................................................................................................................................. 21 4.2.6 EUT Operating Conditions ........................................................................................................ 21 4.2.7 Test Results .............................................................................................................................. 22 5 Pictures of Test Arrangements................................................................................................................ 24 Appendix – Information on the Testing Laboratories ................................................................................ 25 Report No.: RF180821C20-4 Page No. 2 / 25 Report Format Version: 6.1.1

Release Control Record Issue No. Description Date Issued RF180821C20-4 Original Release Sep. 25, 2018 Report No.: RF180821C20-4 Page No. 3 / 25 Report Format Version: 6.1.1

1 Certificate of Conformity Product: Smart Phone Brand: Kyocera Test Model: E6910 Sample Status: Identical Prototype Applicant: Kyocera Corporation c/o Kyocera International, Inc. Test Date: Sep. 18, 2018 Standards: 47 CFR FCC Part 15, Subpart C (Section 15.209) ANSI C63.10: 2013 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s RF characteristics under the conditions specified in this report. Prepared by : , Date: Sep. 25, 2018 Ivonne Wu / Supervisor Approved by : , Date: Sep. 25, 2018 Dylan Chiou / Project Engineer Report No.: RF180821C20-4 Page No. 4 / 25 Report Format Version: 6.1.1

2 Summary of Test Results 47 CFR FCC Part 15, Subpart C (Section 15.209) FCC Clause Test Item Result Remarks Meet the requirement of limit. 15.207 Conducted emission test Pass Minimum passing margin is —14.34 dB at 0.48626 MHz. Meet the requirement of limit. 15.209 Radiated emission test Pass Minimum passing margin is —9.16 dB at 33.88 MHz. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16—4—2: M T F Expended Uncertainty easuremen requenc Mss (k=2) ) Conducted Emissions at mains ports 150 kHz ~ 30 MHz 2.44 dB 30 MHz ~ 200 MHz 2.93 dB Radiated Emissions up to 1 GHz 200 MHz ~ 1000 MHz 2.95 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: RF180821C20—4 Page No. 5 / 25 Report Format Version: 6.1.1

3 General Information 3.1 General Description of EUT Product Smart Phone Brand Kyocera Test Model E6910 Status of EUT Identical Prototype 3.8 Vdc (Battery) Power Supply Rating 5 Vdc or 9 Vdc or 12 Vdc (Adapter) 5 Vdc (Host equipment) Operating Frequency 150 kHz Antenna Connector N/A Accessory Device Refer to Note as below Data Cable Supplied Refer to Note as below Note: 1. The EUT’s accessories list refers to Ext. Pho. 2. The above EUT information is declared by manufacturer and for more detailed features description, please refers to the manufacturer's specifications or user's manual. Report No.: RF180821C20-4 Page No. 6 / 25 Report Format Version: 6.1.1

3.2 Description of Test Modes 1 channel is provided to this EUT: Channel Frequency (kHz) 1 150 3.2.1 Test Mode Applicability and Tested Channel Detail EUT Configure Applicable To Description Mode RE<1G PLC A √ √ Charging Mode B √ - Standby Mode Where RE<1G: Radiated Emission below 1 GHz PLC: Power Line Conducted Emission Radiated Emission Test (Below 1 GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Available Channel Tested Channel A, B 1 1 Power Line Conducted Emission Test: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT Configure Mode Available Channel Tested Channel A 1 1 Test Condition: Applicable To Environmental Conditions Input Power Tested By RE 25 deg. C, 65 % RH 120 Vac, 60 Hz Jisyong Wang PLC 25 deg. C, 65 % RH 120 Vac, 60 Hz Jisyong Wang Report No.: RF180821C20-4 Page No. 7 / 25 Report Format Version: 6.1.1

3.3 Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product Brand Model No. Serial No. FCC ID A. Earphone Funkey FK130102 N/A N/A B. Wireless Charger PAD LG WCP-300 N/A N/A No. Signal Cable Description Of The Above Support Units 1. N/A 2. N/A Note: 1. All power cords of the above support units are non-shielded (1.8m). 3.3.1 Configuration of System under Test Wireless EUT Charger (Power from AC Adapter) Earphone *Test Table 3.4 General Description of Applied Standards The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart C (15.209) ANSI C63.10-2013 All test items have been performed and recorded as per the above standards. Report No.: RF180821C20-4 Page No. 8 / 25 Report Format Version: 6.1.1

4 Test Types and Results 4.1 Radiated Emission and Bandedge Measurement 4.1.1 Limits of Radiated Emission and Bandedge Measurement Frequencies Field Strength Measurement Distance (MHz) (microvolts/meter) (meters) 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30.0 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. For frequencies above 1000 MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20 dB under any condition of modulation. Report No.: RF180821C20-4 Page No. 9 / 25 Report Format Version: 6.1.1

4.1.2 Test Instruments Description & Date of Due Date of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver N9038A MY51210203 Mar. 16, 2018 Mar. 15, 2019 Agilent Spectrum Analyzer N9010A MY52220314 Nov. 24, 2017 Nov. 23, 2018 Agilent Spectrum Analyzer FSU43 101261 Jan. 11, 2018 Jan. 10, 2019 ROHDE & SCHWARZ BILOG Antenna VULB 9168 9168-472 Dec. 06, 2017 Dec. 05, 2018 SCHWARZBECK Loop Antenna EM-6879 269 Sep. 07, 2018 Sep. 06, 2019 Preamplifier EMC001340 980201 Nov. 01, 2017 Oct. 30, 2018 EMCI Preamplifier EMC 330H 980112 Oct. 13, 2017 Oct. 12, 2018 EMCI Power Sensor MA2411B 1315050 Sep. 04, 2018 Sep. 03, 2019 Anritsu RF Coaxial Cable 8D-FB Cable-Ch10-01 Oct. 20, 2017 Oct. 19, 2018 Worken Boresight Antenna Fixture FBA-01 FBA-SIP01 NA NA Software E3 NA NA NA BV ADT 6.120103 Antenna Tower MFA-440H NA NA NA MF Turn Table MFT-201SS NA NA NA MF Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Chamber 10. 3. The horn antenna and preamplifier (model: EMC 184045) are used only for the measurement of emission frequency above 1GHz if tested. 4. The IC Site Registration No. is IC7450F-10. Report No.: RF180821C20-4 Page No. 10 / 25 Report Format Version: 6.1.1

4.1.3 Test Procedures For Radiated Emission below 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. Both Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9 kHz at frequency below 30 MHz. For Radiated Emission above 30 MHz a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. f. The test-receiver system was set to peak and average detected function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets average limit, measurement with the average detector is unnecessary. Note: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 kHz for Quasi-peak detection (QP) at frequency below 1 GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz for Peak detection (PK) at frequency above 1 GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T (Duty cycle < 98 %) or 10 Hz (Duty cycle ≥ 98 %) for Average detection (AV) at frequency above 1 GHz. 4. All modes of operation were investigated and the worst-case emissions are reported. 4.1.4 Deviation from Test Standard No deviation. Report No.: RF180821C20-4 Page No. 11 / 25 Report Format Version: 6.1.1

4.1.5 Test Setup <Radiated Emission below 30 MHz> 1m EUT& 3m Support Units Turn Table 80 cm Ground Plane Test Receiver <Radiated Emission 30 MHz to 1 GHz> Ant. Tower 1-4m Variable 3m 10m EUT& Support Units Turn Table 80cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.1.6 EUT Operating Conditions Set the EUT under transmission condition continuously at specific channel frequency. Report No.: RF180821C20-4 Page No. 12 / 25 Report Format Version: 6.1.1

4.1.7 Test Results <Charging Mode> EUT Test Condition Measurement Detail Input Power 120 Vac, 60 Hz Frequency Range 0.009 ~ 30 MHz Environmental Average 25 deg. C, 65 % RH Detector Function Conditions Quasi-Peak Tested By Jisyong Wang Antenna Polarity & Test Distance: Open at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 0.147 80.86 101.49 104.26 -23.4 20.31 0.02 40.96 100 360 Average 0.294 60.18 80.69 98.24 -38.06 20.27 0.02 40.8 100 360 Average 0.441 54.13 74.51 94.72 -40.59 20.26 0.05 40.69 100 360 Average 0.588 51.44 71.78 72.22 -20.78 20.25 0.08 40.67 100 360 QP 0.735 47.43 67.77 70.28 -22.85 20.26 0.1 40.7 100 360 QP 0.882 48.85 69.19 68.69 -19.84 20.27 0.12 40.73 100 360 QP 1.029 44.54 64.88 67.36 -22.82 20.27 0.13 40.74 100 360 QP Antenna Polarity & Test Distance: Close at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 0.147 77.81 98.44 104.26 -26.45 20.31 0.02 40.96 100 0 Average 0.294 60.93 81.44 98.24 -37.31 20.27 0.02 40.8 100 0 Average 0.441 56.52 76.9 94.72 -38.2 20.26 0.05 40.69 100 0 Average 0.588 49.89 70.23 72.22 -22.33 20.25 0.08 40.67 100 0 QP 0.735 49.18 69.52 70.28 -21.1 20.26 0.1 40.7 100 0 QP 0.882 46.72 67.06 68.69 -21.97 20.27 0.12 40.73 100 0 QP 1.029 43.91 64.25 67.36 -23.45 20.27 0.13 40.74 100 0 QP Antenna Polarity & Test Distance: Ground-parallel at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 0.147 80.48 101.11 104.26 -23.78 20.31 0.02 40.96 100 360 Average 0.294 60.35 80.86 98.24 -37.89 20.27 0.02 40.8 100 360 Average 0.441 53.77 74.15 94.72 -40.95 20.26 0.05 40.69 100 360 Average 0.588 49.54 69.88 72.22 -22.68 20.25 0.08 40.67 100 360 QP 0.735 48.77 69.11 70.28 -21.51 20.26 0.1 40.7 100 360 QP 0.882 47.88 68.22 68.69 -20.81 20.27 0.12 40.73 100 360 QP 1.029 44.62 64.96 67.36 -22.74 20.27 0.13 40.74 100 360 QP Remarks: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. Above limits have been translated by the formula Report No.: RF180821C20-4 Page No. 13 / 25 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Input Power 120 Vac, 60 Hz Frequency Range 30 MHz ~ 1000 MHz Environmental 25 deg. C, 65 % RH Detector Function Peak Conditions Tested By Jisyong Wang Horizontal Vertical Report No.: RF180821C20-4 Page No. 14 / 25 Report Format Version: 6.1.1

Antenna Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Cable Antenna Table Frequency Limit Margin Preamp Level Level Factor Loss Height Angle Remark (MHz) (dBuV/m) (dB) Factor (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 43.58 22.64 39.66 40 -17.36 13.59 0.5 31.11 152 111 Peak 202.66 27.3 48.3 43.5 -16.2 9.48 1.24 31.72 165 231 Peak 324.88 19.78 36.32 46 -26.22 13.54 1.77 31.85 185 265 Peak 633.34 24.28 33.35 46 -21.72 20.01 3.04 32.12 111 185 Peak 851.59 28.39 33.54 46 -17.61 22.89 3.84 31.88 111 231 Peak 947.62 29.5 33.34 46 -16.5 23.78 4.22 31.84 165 285 Peak Antenna Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Cable Antenna Table Frequency Limit Margin Preamp Level Level Factor Loss Height Angle Remark (MHz) (dBuV/m) (dB) Factor (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 204.6 21.29 42.17 43.5 -22.21 9.56 1.25 31.69 165 132 Peak 378.23 18.65 33.77 46 -27.35 14.82 2 31.94 111 195 Peak 580.96 23.05 33.18 46 -22.95 19.17 2.82 32.12 174 152 Peak 705.12 25.78 33.32 46 -20.22 20.89 3.33 31.76 165 231 Peak 795.33 27.97 33.57 46 -18.03 22.16 3.66 31.42 158 111 Peak 902.03 28.89 33.34 46 -17.11 23.52 4.05 32.02 165 132 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor 2. Margin value = Emission level – Limit value. 3. The other emission levels were very low against the limit. Report No.: RF180821C20-4 Page No. 15 / 25 Report Format Version: 6.1.1

<Standby Mode> EUT Test Condition Measurement Detail Input Power 120 Vac, 60 Hz Frequency Range 0.009 ~ 30 MHz Environmental Average 25 deg. C, 65 % RH Detector Function Conditions Quasi-Peak Tested By Jisyong Wang Antenna Polarity & Test Distance: Open at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 0.261 66.01 86.53 99.27 -33.26 20.28 0.02 40.82 100 360 Average 0.399 65.01 85.42 95.58 -30.57 20.26 0.04 40.71 100 360 Average 0.529 50.23 70.57 73.13 -22.9 20.25 0.07 40.66 100 360 QP 0.669 61.21 81.55 71.1 -9.89 20.26 0.09 40.69 100 360 QP 0.789 48.12 68.46 69.66 -21.54 20.26 0.11 40.71 100 360 QP 0.911 52.01 72.35 68.41 -16.4 20.27 0.12 40.73 100 360 QP Antenna Polarity & Test Distance: Close at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 0.278 63.01 83.53 98.72 -35.71 20.27 0.02 40.81 100 0 Average 0.351 62.85 83.31 96.7 -33.85 20.26 0.03 40.75 100 0 Average 0.501 50.75 71.09 73.61 -22.86 20.25 0.06 40.65 100 0 QP 0.629 57.25 77.59 71.63 -14.38 20.26 0.08 40.68 100 0 QP 0.771 45.98 66.33 69.86 -23.88 20.26 0.1 40.71 100 0 QP 0.899 48.03 68.37 68.53 -20.5 20.27 0.12 40.73 100 0 QP Antenna Polarity & Test Distance: Ground-parallel at 3 m Emission Read Antenna Preamp Antenna Table Frequency Limit Margin Cable Level Level Factor Factor Height Angle Remark (MHz) (dBuV/m) (dB) Loss (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 0.236 64.01 84.56 100.15 -36.14 20.28 0.02 40.85 100 360 Average 0.371 65.25 85.68 96.22 -30.97 20.26 0.04 40.73 100 360 Average 0.485 50.98 71.33 93.89 -42.91 20.25 0.06 40.66 100 360 QP 0.621 58.65 78.99 71.74 -13.09 20.26 0.08 40.68 100 360 QP 0.748 48.25 68.59 70.13 -21.88 20.26 0.1 40.7 100 360 QP 0.889 50.36 70.7 68.63 -18.27 20.27 0.12 40.73 100 360 QP Remarks: 1. Emission level (dBuV/m) = Raw Value (dBuV) + Correction Factor (dB/m) 2. Correction Factor (dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) – Pre-Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level – Limit value. 5. Above limits have been translated by the formula Report No.: RF180821C20-4 Page No. 16 / 25 Report Format Version: 6.1.1

EUT Test Condition Measurement Detail Input Power 120 Vac, 60 Hz Frequency Range 30 MHz ~ 1000 MHz Environmental 25 deg. C, 65 % RH Detector Function Peak Conditions Tested By Jisyong Wang Horizontal Vertical Report No.: RF180821C20-4 Page No. 17 / 25 Report Format Version: 6.1.1

Antenna Polarity & Test Distance: Horizontal at 3 m Emission Read Antenna Cable Antenna Table Frequency Limit Margin Preamp Level Level Factor Loss Height Angle Remark (MHz) (dBuV/m) (dB) Factor (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 206.54 25.69 46.44 43.5 -17.81 9.65 1.26 31.66 152 213 Peak 323.91 17.9 34.47 46 -28.1 13.52 1.77 31.86 111 231 Peak 461.65 20.74 33.82 46 -25.26 16.56 2.33 31.97 165 285 Peak 589.69 23.15 33.07 46 -22.85 19.37 2.85 32.14 195 251 Peak 738.1 26.2 32.89 46 -19.8 21.35 3.46 31.5 111 165 Peak 914.64 29.07 33.4 46 -16.93 23.59 4.11 32.03 102 251 Peak Antenna Polarity & Test Distance: Vertical at 3 m Emission Read Antenna Cable Antenna Table Frequency Limit Margin Preamp Level Level Factor Loss Height Angle Remark (MHz) (dBuV/m) (dB) Factor (dB) (dBuV/m) (dBuV) (dB/m) (dB) (cm) (Degree) 33.88 30.84 48.83 40 -9.16 12.63 0.46 31.08 102 251 Peak 202.66 20.42 41.42 43.5 -23.08 9.48 1.24 31.72 165 231 Peak 416.06 19.36 33.59 46 -26.64 15.66 2.14 32.03 147 185 Peak 620.73 23.85 33.17 46 -22.15 19.86 2.99 32.17 165 285 Peak 852.56 28.28 33.4 46 -17.72 22.9 3.86 31.88 165 295 Peak 965.08 30.16 33.89 54 -23.84 23.87 4.3 31.9 111 165 Peak Remarks: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor 2. Margin value = Emission level – Limit value. 3. The other emission levels were very low against the limit. Report No.: RF180821C20-4 Page No. 18 / 25 Report Format Version: 6.1.1

4.2 Conducted Emission Measurement 4.2.1 Limits of Conducted Emission Measurement Conducted Limit (dBuV) Frequency (MHz) Quasi-Peak Average 0.15 - 0.5 66 - 56 56 - 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50 Note: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 4.2.2 Test Instruments Description & Date of Due Date of Model No. Serial No. Manufacturer Calibration Calibration Test Receiver ESCI 100613 Nov. 23, 2017 Nov. 22, 2018 ROHDE & SCHWARZ RF signal cable 5D-FB Cable-cond1-01 Sep. 05, 2018 Sep. 04, 2019 Woken LISN/AMN ROHDE & SCHWARZ ENV216 101826 Feb. 26, 2018 Feb. 25, 2019 (EUT) LISN/AMN ROHDE & SCHWARZ ESH3-Z5 100311 Aug. 19, 2018 Aug. 18, 2019 (Peripheral) Software BV ADT_Cond_ NA NA NA ADT V7.3.7.4 Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. Report No.: RF180821C20-4 Page No. 19 / 25 Report Format Version: 6.1.1

4.2.3 Test Procedures a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50 uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20 dB) was not recorded. NOTE: The resolution bandwidth and video bandwidth of test receiver is 9 kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15 MHz - 30 MHz. Report No.: RF180821C20-4 Page No. 20 / 25 Report Format Version: 6.1.1

4.2.4 Deviation from Test Standard No deviation. 4.2.5 Test Setup Vertical Ground Reference Plane Test Receiver EUT o o o o 40cm U 1 5 a s o 80cm LISN L L1 L \ N Ho T rizontal G round Refere Plane nce Note: 1.Support units were connected to second LISN. For the actual test configuration, please refer to the attached file (Test Setup Photo). 4.2.6 EUT Operating Conditions Same as 4.1.6. Report No.: RF180821C20—4 Page No. 21 / 25 Report Format Version: 6.1.1

4.2.7 Test Results Detector Function & . Frequency Range 150kHz ~ 30MHz Resolu}ion S:;'S;;;Ze(%/go:lzr/lz Bandwidth " Input Power 120Vac, 60Hz Eg‘r’]';‘ii?o’:]‘:”‘a' 25°C, 65%RH Tested by Jisyong Wang Test Date 2018/9/18 Phase Of Power : Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15000 9.67 30.53 16.62 40.20 26.29 66.00 56.00 —25.80 —29.71 2 0.18075 9.67 28.42 1541 38.09 25.08 64.45 54.45 —26.36 —29.37 3 0.39635 9.66 23.74 10.05 33.40 19.71 57.93 47.93 —24.53 —28.22 4 0.48626 9.66 82.23 15.07 41.89 24.73 56.23 46.23 —14.34 —21.50 5 2.06981 9.68 24.76 8.59 34.44 18.27 56.00 46.00 —21.56 —27.73 6 7.84097 9.81 30.94 1543 40.75 25.24 60.00 50.00 —19.25 —24.76 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value =aaaeaeaaufig soke 0 a mane Report No.: RF180821C20—4 Page No. 22 / 25 Report Format Version: 6.1.1

Detector Function & Quasi—Peak (QP) / Frequency Range 150kHz ~ 30MHz g{giglwultgl)fl Average (AV), 9KHz Input Power 120Vac, 60Hz Eg‘r’]';‘ii?o”r:sma' 25°C, 65%RH Tested by Jisyong Wang Test Date 2018/9/18 Phase Of Power : Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuyV) (dBuV) (dBuyV) (dB) (MHz) (dB) Q.P. AV. Q.P AV. Q.P. AV. Q.P. AV. 1 0.17283 9.68 12.93 1.33 22.61 11.01 64.82 54.82 —42.21 —43.81 2 0.47453 9.67 15.90 0.92 25.57 10.59 56.43 46.43 —30.86 —35.84 3 0.81861 9.66 15.58 2.86 25.24 12.52 56.00 46.00 —30.76 —33.48 4 7.86834 9.81 21.15 240 30.96 12.21 60.00 50.00 —29.04 —37.79 5 12.87314 9.91 22.87 4.70 8278 14.61 60.00 50.00 —27.22 —35.39 6 17.17023 9.97 21.74 2.34 31.71 12.31 60.00 50.00 —28.29 —37.69 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value $# B # s g 8 g s 8 B0 8 59 :l'llm & rane Report No.: RF180821C20—4 Page No. 23 / 25 Report Format Version: 6.1.1

5 Pictures of Test Arrangements Please refer to the attached file (Test Setup Photo). Report No.: RF180821C20-4 Page No. 24 / 25 Report Format Version: 6.1.1

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC recognized accredited test firms and accredited according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: RF180821C20-4 Page No. 25 / 25 Report Format Version: 6.1.1


Document Created: 2019-05-01 01:35:31
Document Modified: 2019-05-01 01:35:31
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC