SAR Validations

FCC ID: V65C5155

RF Exposure Info

Download: PDF
FCCID_1728639

                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0


EXHIBIT 9 APPENDIX A: SAR VALIDATION PLOTS


                                          Validation for HEAD




© 2012 Comptest Services LLC                         Page 1 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/21/2012

835MHz Validation @ 20dbm, Probe #1618, DAE#602, Dipole #467
Communication System: CDMA, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                                   3
Medium: Head 835 MHz,Medium parameters used: f = 835 MHz; σ = 0.91 mho/m; εr = 41.5; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ET3DV6 - SN1618, ConvF(6.31, 6.31, 6.31), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz Validation/Area Scan (61x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.06 mW/g

835MHz Validation/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 35.5 V/m; Power Drift = -0.123 dB
Peak SAR (extrapolated) = 1.41 W/kg

SAR(1 g) = 0.974 mW/g; SAR(10 g) = 0.639 mW/g
Maximum value of SAR (measured) = 1.05 mW/g




                                  0 dB = 1.06mW/g




© 2012 Comptest Services LLC                         Page 2 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                  COMPTEST                 Services LLC

                                                                   Interpolated SAR(x.y,z,f0)
                                                                   SAR; Z Scan: Value Along Z, X=0, Y=0




        al_R
                                /
            4
            T
 mW!g




        ab| _A
            T
        O
        &




        sal                                _ _]&
        0.0 |—                                                \M__H_HM                                                                       .        A.d—a——*—’*—"“““w
            1           |   L       _|          |   |   |          L   _|   |          |   |   |          L   _|   |          |   L   _|          |    L   _|          |   |   |

                 0.00                    0.02               0.04                0.06               0.08                0.10                0.12                 0.14               0.16
                                                                                                   m




[' "l riee epeceeepreabrordaiebueperarttr Ortiusmy rermg en reare srre reerirone oiuin on e urripe n ven evrrreve emen _ 1


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/22/2012

835MHz Validation @ 20dbm, Probe #1618, DAE#602, Dipole #467
Communication System: CDMA, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                                 3
Medium: Head 835 MHz,Medium parameters used: f = 835 MHz; σ = 0.92 mho/m; εr = 43; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ET3DV6 - SN1618, ConvF(6.31, 6.31, 6.31), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz Validation/Area Scan (61x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.06 mW/g

835MHz Validation/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 34.9 V/m; Power Drift = 0.019 dB
Peak SAR (extrapolated) = 1.40 W/kg

SAR(1 g) = 0.974 mW/g; SAR(10 g) = 0.639 mW/g
Maximum value of SAR (measured) = 1.05 mW/g




                                0 dB = 1.06mW/g




© 2012 Comptest Services LLC                         Page 4 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/26/2012

835MHz Validation @ 20dbm, Probe #1618, DAE#602, Dipole #467
Communication System: CDMA, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                                   3
Medium: Head 835 MHz,Medium parameters used: f = 835 MHz; σ = 0.91 mho/m; εr = 42.1; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ET3DV6 - SN1618, ConvF(6.31, 6.31, 6.31), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz Validation/Area Scan (61x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.04 mW/g

835MHz Validation/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 35.3 V/m; Power Drift = -0.196 dB
Peak SAR (extrapolated) = 1.33 W/kg

SAR(1 g) = 0.930 mW/g; SAR(10 g) = 0.610 mW/g
Maximum value of SAR (measured) = 1.01 mW/g




                                0 dB = 1.04mW/g




© 2012 Comptest Services LLC                         Page 5 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/19/2012

1900Mhz Validation @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
Medium: HSL1900,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.43 mho/m; ε r = 38.1; ρ = 1000
     3
kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(5.06, 5.06, 5.06), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 4.80 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 54.8 V/m; Power Drift = 0.008 dB
Peak SAR (extrapolated) = 7.39 W/kg

SAR(1 g) = 3.99 mW/g; SAR(10 g) = 2.07 mW/g
Maximum value of SAR (measured) = 4.49 mW/g




                                    0 dB = 4.80mW/g




© 2012 Comptest Services LLC                         Page 6 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/20/2012

1900Mhz Validation @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
Medium: HSL1900,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.46 mho/m; ε r = 38.5; ρ = 1000
     3
kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(5.06, 5.06, 5.06), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 4.67 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 55.2 V/m; Power Drift = 0.069 dB
Peak SAR (extrapolated) = 7.51 W/kg

SAR(1 g) = 4.04 mW/g; SAR(10 g) = 2.09 mW/g
Maximum value of SAR (measured) = 4.53 mW/g




                                    0 dB = 4.67mW/g




© 2012 Comptest Services LLC                         Page 7 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


             COMPTEST
                                                                                   ty < < > >




                Services LLC

                         Interpolated SAR(x.y,z,f0)
                         SAR; Z Scan: Value Along Z, X=0, Y=0

       5.5

       5.0

       4.5

       4.0

       3.5

       3.0
mW!g




       2.5

       2.0

       1.5

       1.0

       0.5




                                                     bevwen n vever reeven ev weowe ner e per n neves w mev n rvevene en ues   =]


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/10/2012

1900Mhz Validation @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
                                                                                                            3
Medium: HSL1900,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.42 mho/m; εr = 39; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(5.06, 5.06, 5.06), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 4.92 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 54.5 V/m; Power Drift = -0.007 dB
Peak SAR (extrapolated) = 7.48 W/kg

SAR(1 g) = 4.03 mW/g; SAR(10 g) = 2.09 mW/g
Maximum value of SAR (measured) = 4.51 mW/g




                                    0 dB = 4.92mW/g




© 2012 Comptest Services LLC                         Page 9 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/05/2012

2450MHz Validation, Probe #3078, DAE #530, Dipole #776
Communication System: CW, Frequency: 2450 MHz, Duty Cycle: 1:1
                                                                                               3
Medium: HSL2450,Medium parameters used: f = 2450 MHz; σ = 1.86 mho/m; εr = 38.1; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3078, ConvF(4.36, 4.36, 4.36), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn530,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

2450MHz Validation @20dBm/Area Scan (61x71x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 7.17 mW/g

2450MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 53.3 V/m; Power Drift = -0.161 dB
Peak SAR (extrapolated) = 12.5 W/kg

SAR(1 g) = 5.62 mW/g; SAR(10 g) = 2.52 mW/g
Maximum value of SAR (measured) = 6.35 mW/g




                                 0 dB = 7.17mW/g




© 2012 Comptest Services LLC                        Page 10 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0




© 2012 Comptest Services LLC                        Page 11 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

                                          Validation for BODY




© 2012 Comptest Services LLC                        Page 12 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/06/2012

835MHz Validation (in Muscle), Probe #3035, DAE #602, Dipole #467
Communication System: CW, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                           3
Medium: M800,Medium parameters used: f = 835 MHz; σ = 0.94 mho/m; εr = 53.8; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3035, ConvF(6.09, 6.09, 6.09), Calibrated: 2/22/2012
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz/Area Scan (51x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.11 mW/g

835MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 34.8 V/m; Power Drift = 0.025 dB
Peak SAR (extrapolated) = 1.52 W/kg

SAR(1 g) = 1.04 mW/g; SAR(10 g) = 0.688 mW/g
Maximum value of SAR (measured) = 1.12 mW/g




                                0 dB = 1.11mW/g




© 2012 Comptest Services LLC                        Page 13 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                   COMPTEST                Services LLC

                                                                   Interpolated SAR(x.y,z,f0)
                                                                   SAR; Z Scan: Value Along Z, X=0, Y=0




       2l —f
       wl
       wl |
                                 /
             4
mW!g

             T




       ab [\
             T
       O
       O




       al                                  _A
       0.0                                                                       *#e                                    _               —          e—t)*« _

             _1          I   I       I          I   I   I          I   I   I          I   I   I          I   I   I          I   I   I          I   I   I          I   I   I

                  0.00                   0.02               0.04               0.06               0.08               0.10               0.12               0.14               0.16
                                                                                                  m




[' "l riee epecerepreabrordaiebueperartetr Orntofur fe nenrourerireeerirone oiuin on e urripe n ven evrrreve emen _ W


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/09/2012

835MHz Validation (in Muscle), Probe #3035, DAE #602, Dipole #467
Communication System: CW, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                           3
Medium: M800,Medium parameters used: f = 835 MHz; σ = 0.94 mho/m; εr = 53.3; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3035, ConvF(6.09, 6.09, 6.09), Calibrated: 2/22/2012
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz/Area Scan (51x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.12 mW/g

835MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 32.7 V/m; Power Drift = -0.020 dB
Peak SAR (extrapolated) = 1.50 W/kg

SAR(1 g) = 1.03 mW/g; SAR(10 g) = 0.686 mW/g
Maximum value of SAR (measured) = 1.11 mW/g




                             0 dB = 1.12mW/g




© 2012 Comptest Services LLC                        Page 15 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/10/2012

835MHz Validation (in Muscle), Probe #3035, DAE #602, Dipole #467
Communication System: CW, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                           3
Medium: M800,Medium parameters used: f = 835 MHz; σ = 0.94 mho/m; εr = 53.7; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3035, ConvF(6.09, 6.09, 6.09), Calibrated: 2/22/2012
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz/Area Scan (51x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.12 mW/g

835MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 34.0 V/m; Power Drift = 0.013 dB
Peak SAR (extrapolated) = 1.50 W/kg

SAR(1 g) = 1.03 mW/g; SAR(10 g) = 0.682 mW/g
Maximum value of SAR (measured) = 1.11 mW/g




                                 0 dB = 1.12mW/g




© 2012 Comptest Services LLC                        Page 16 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/11/2012

835MHz Validation (in Muscle), Probe #3035, DAE #602, Dipole #467
Communication System: CW, Frequency: 835 MHz, Duty Cycle: 1:1
                                                                                           3
Medium: M800,Medium parameters used: f = 835 MHz; σ = 0.94 mho/m; εr = 53.8; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3035, ConvF(6.09, 6.09, 6.09), Calibrated: 2/22/2012
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn602,Calibrated: 9/16/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                          22.0

835MHz/Area Scan (51x121x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 1.13 mW/g

835MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 32.1 V/m; Power Drift = 0.057 dB
Peak SAR (extrapolated) = 1.53 W/kg

SAR(1 g) = 1.04 mW/g; SAR(10 g) = 0.691 mW/g
Maximum value of SAR (measured) = 1.13 mW/g




                              0 dB = 1.13mW/g




© 2012 Comptest Services LLC                        Page 17 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                  COMPTEST
                         Services LLC

                                       Interpolated SAR(x.y,z,f0)
                                       SAR; Z Scan: Value Along Z, X=0, Y=0




       l _
                   /
mW!g

             I




       "H T
       &
       &




       s                 _A
       U.U   |_                                             |~~*—4——4.                   , _—#——t—#——4




[' "l riee epeceeepreabrordaiebueperarttr Orniut fe nenreurerireeerirone oiuin on e urripe n ven evrrreve emen _ 1


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/26/2012

1900Mhz Validation (Muscle) @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
                                                                                                             3
Medium: M1800,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.54 mho/m; ε r = 51.9; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(4.57, 4.57, 4.57), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 4.91 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 54.2 V/m; Power Drift = 0.022 dB
Peak SAR (extrapolated) = 7.44 W/kg

SAR(1 g) = 4.11 mW/g; SAR(10 g) = 2.15 mW/g
Maximum value of SAR (measured) = 4.66 mW/g




                                    0 dB = 4.91mW/g




© 2012 Comptest Services LLC                        Page 19 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/27/2012

1900Mhz Validation (Muscle) @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
                                                                                                             3
Medium: M1800,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.53 mho/m; ε r = 51.8; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(4.57, 4.57, 4.57), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 5.28 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 47.3 V/m; Power Drift = 0.125 dB
Peak SAR (extrapolated) = 7.73 W/kg

SAR(1 g) = 4.27 mW/g; SAR(10 g) = 2.23 mW/g
Maximum value of SAR (measured) = 4.87 mW/g




                                    0 dB = 5.28mW/g




© 2012 Comptest Services LLC                        Page 20 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                     COMPTEST                                              Services LLC

                                                                                                 Interpolated SAR(x.y,z,f0)
                                                                                                 SAR; Z Scan: Value Along Z, X=0, Y=0
     4.5
            TT T


                     4*




     4.0
                      a+r**|
             TT
             TT




     3.5
                               ;—/"__F’—.—‘
            TTTT




     3.0
                                              |_——~I
            TT TT
     ID)
       on




                                                       ’//r—""
             TT
mW!g

             TT
Do
S




                                                                 se
                                                                      _




     1.0                                                               s
                                                                       x




     0.5—                                                                        \
     UU       |—                                                                            |~@——g_—4——*l—*——*             *——*~—#+— 42004                                       ‘,_o—"-'_"'-_’_‘—\—‘_‘w

              [_|                    L                   __L__               1   __L__|          L   __L__          L   __L__          L   __L__          L   __L__          L    __L__          L   ____

                    0.00                                              0.02                0.04               0.06               0.08               0.10               0.12                0.14              0.16
                                                                                                                                m




[' "l riee epeceeepreabrordaiebuepertrttr Oritut fe nenirearerirereerirone oiuin on e urripe n ven evrrreve emen _ 1


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/03/2012

1900Mhz Validation (Muscle) @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
                                                                                                            3
Medium: M1800,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.51 mho/m; εr = 51.2; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(4.57, 4.57, 4.57), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 4.92 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 57.5 V/m; Power Drift = -0.074 dB
Peak SAR (extrapolated) = 7.53 W/kg

SAR(1 g) = 4.16 mW/g; SAR(10 g) = 2.17 mW/g
Maximum value of SAR (measured) = 4.76 mW/g




                                    0 dB = 4.92mW/g




© 2012 Comptest Services LLC                        Page 22 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 04/04/2012

1900Mhz Validation (Muscle) @ 20dBm Probe 3036, DAE 675 and Dipole 5d016
Communication System: CW, Frequency: 1900 MHz, Duty Cycle: 1:1
                                                                                                           3
Medium: M1800,Medium parameters used (interpolated): f = 1900 MHz; σ = 1.5 mho/m; εr = 51.3; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3036, ConvF(4.57, 4.57, 4.57), Calibrated: 5/11/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn675,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

1900MHz Validation @20dBm/Area Scan (61x61x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 4.95 mW/g

1900MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 54.7 V/m; Power Drift = -0.189 dB
Peak SAR (extrapolated) = 7.30 W/kg

SAR(1 g) = 4.06 mW/g; SAR(10 g) = 2.13 mW/g
Maximum value of SAR (measured) = 4.55 mW/g




                                    0 dB = 4.95mW/g




© 2012 Comptest Services LLC                        Page 23 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/27/2012

2450MHz Validation (in Muscle), Probe #3078, DAE #530, Dipole #776
Communication System: CW, Frequency: 2450 MHz, Duty Cycle: 1:1
                                                                                                          3
Medium: M2450,Medium parameters used (interpolated): f = 2450 MHz; σ = 2.03 mho/m; εr = 51; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3078, ConvF(4.16, 4.16, 4.16), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn530,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

2450MHz Validation @20dBm/Area Scan (61x71x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 7.57 mW/g

2450MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 52.8 V/m; Power Drift = -0.183 dB
Peak SAR (extrapolated) = 12.8 W/kg

SAR(1 g) = 5.89 mW/g; SAR(10 g) = 2.68 mW/g
Maximum value of SAR (measured) = 6.75 mW/g




                                 0 dB = 7.57mW/g




© 2012 Comptest Services LLC                        Page 24 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


               COMPTEST              Services LLC

                                                            Interpolated SAR(x.y,z,f0)
                                                           SAR; Z Scan: Value Along Z, X=0, Y=0




                                 *




        1          1   _|   1          1   __L__|          1__L__          1   1   _          1   __L__|          1   __L__|          1   _          L   _

            0.00                0.02                0.04            0.06               0.08                0.10                0.12           0.14           0.16
                                                                                       m




[' "l riee epeceeeprearbrordaiebuepertrttr Oritut fe nrenireuesrireeerirone oiuin on e urripe n ven evrrreve emen _ 1


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/28/2012

2450MHz Validation (in Muscle), Probe #3078, DAE #530, Dipole #776
Communication System: CW, Frequency: 2450 MHz, Duty Cycle: 1:1
                                                                                                         3
Medium: M2450,Medium parameters used (interpolated): f = 2450 MHz; σ = 2 mho/m; εr = 50.9; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3078, ConvF(4.16, 4.16, 4.16), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn530,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

2450MHz Validation @20dBm/Area Scan (61x71x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 7.43 mW/g

2450MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 53.0 V/m; Power Drift = -0.004 dB
Peak SAR (extrapolated) = 12.7 W/kg

SAR(1 g) = 5.86 mW/g; SAR(10 g) = 2.66 mW/g
Maximum value of SAR (measured) = 6.69 mW/g




                                 0 dB = 7.43mW/g




© 2012 Comptest Services LLC                        Page 26 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 03/29/2012

2450MHz Validation (in Muscle), Probe #3078, DAE #530, Dipole #776
Communication System: CW, Frequency: 2450 MHz, Duty Cycle: 1:1
                                                                                                         3
Medium: M2450,Medium parameters used (interpolated): f = 2450 MHz; σ = 2 mho/m; εr = 50.9; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3078, ConvF(4.16, 4.16, 4.16), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn530,Calibrated: 5/5/2011
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:
Room T = 21.8                           22.0

2450MHz Validation @20dBm/Area Scan (61x71x1): Measurement grid: dx=15mm, dy=15mm
Maximum value of SAR (interpolated) = 7.36 mW/g

2450MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 52.9 V/m; Power Drift = -0.013 dB
Peak SAR (extrapolated) = 12.9 W/kg

SAR(1 g) = 5.92 mW/g; SAR(10 g) = 2.68 mW/g
Maximum value of SAR (measured) = 6.74 mW/g




                                 0 dB = 7.36mW/g




© 2012 Comptest Services LLC                        Page 27 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.


                                                                       Applicant:   Kyocera
                                                                        FCC ID:     V65C5155
                                                                       Report #:    CT-C5155-9A-0312-R0

Test Laboratory: Comptest/Kyocera                                                               Date: 06/15/2012

2450MHz Validation (in Muscle), Probe #3078, DAE #530, Dipole #776

Communication System: CW, Frequency: 2450 MHz, Duty Cycle: 1:1
                                                                                                           3
Medium: M2450,Medium parameters used (interpolated): f = 2450 MHz; σ = 2.04 mho/m; ε r = 51; ρ = 1000 kg/m
Phantom: SAM 12,Phantom section: Flat Section
DASY4 Configuration:
Probe: ES3DV3 - SN3078, ConvF(4.16, 4.16, 4.16), Calibrated: 9/19/2011
Sensor-Surface: 4mm (Mechanical Surface Detection),
Electronics: DAE4 Sn530,Calibrated: 5/30/2012
Measurement SW: DASY4, V4.7 Build 80
Postprocessing SW: SEMCAD, V1.8 Build 186
Temperature:Room T = 21.8 +/- 1 deg C, Liquid T = 22.0 +/- 1 deg C

2450MHz Validation @20dBm/Area Scan (61x71x1): Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (interpolated) = 7.14 mW/g

2450MHz Validation @20dBm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm
Reference Value = 51.7 V/m; Power Drift = 0.188 dB
Peak SAR (extrapolated) = 12.5 W/kg
SAR(1 g) = 5.71 mW/g; SAR(10 g) = 2.58 mW/g

Maximum value of SAR (measured) = 6.54 mW/g




                             0 dB = 7.14mW/g




© 2012 Comptest Services LLC                        Page 28 of 28                           SAR Validation Plots
    This report shall not be reproduced except in full, without the written consent of CompTest Services LLC.



Document Created: 2012-06-18 12:23:17
Document Modified: 2012-06-18 12:23:17

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC