PCE Test Report

FCC ID: UTWXM5WA

Test Report

Download: PDF
FCCID_2484326

FCC ID: UTWXMSWA IC: 6914A—XMSWA Report No.: DRTFCC1411—1498 Dt&C Total 25 Pages RF TEST REPORT Test item : Mobile Computer Model No. : FCC: XMS5 IC: XMSWA Order No. : DTNC1410—04626, DTNC1410—04629 Date of receipt : 2014—10—23 Test duration : _2014—11—03 ~2014—11—17 Date of issue : _2014—11—26 Use of report : FCC & IC Original Grant Applicant _: Janam Technologies LLC 100 Crossways Park West Suite 105, Woodbury, New York 11797 USA Test laboratory : DT&C Co., Ltd. 42, Yurim—ro, 154beon—gil, Cheoin—gu, Yongin—si, Gyeonggi—do, Korea 449—935 Test specification : §22(H), §24(E), RSS—132, RSS—133 Test environment _: See appended test report Test result ; Pass C Fail The test results presented in this test report are limited only to the sample supplied by applicant and the use of this test report is inhibited otherthanits purpose. This test report shall not be reproduced except in full, withoutthe written approval of DIG DT&C Co., Ltd. Tested by: Reviewed by: g§: w Engineer Technical Man’ager SeokHwan Hong HongHee Lee TRF—RF—210(04)140901 DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 Test Report Version Test Report No. Date Description DRTFCC1411-1498 Nov. 26, 2014 Initial issue TRF-RF-210(04)140901 Page 2 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 Table of Contents 1. GENERAL INFORMATION ......................................................... 4 2. INTRODUCTION ......................................................................... 5 2.1. EUT DESCRIPTION............................................................................................ 5 2.2. MEASURING INSTRUMENT CALIBRATION .................................................... 5 2.3. TEST FACILITY .................................................................................................. 5 3. DESCRIPTION OF TESTS .......................................................... 6 3.1 ERP & EIRP ......................................................................................................... 6 3.2 PEAK TO AVERAGE RATIO ............................................................................... 8 3.3 OCCUPIED BANDWIDTH. ................................................................................ 10 3.4 BAND EDGE EMISSIONS AT ANTENNA TERMINAL...................................... 11 3.5 SPURIOUS AND HARMONIC EMISSIONS AT ANTENNA TERMINAL. .......... 12 3.6 RADIATED SPURIOUS EMISSIONS ................................................................ 13 3.7 FREQUENCY STABILITY / VARIATION OF AMBIENT TEMPERATURE ........ 14 4. LIST OF TEST EQUIPMENT..................................................... 15 5. SUMMARY OF TEST RESULTS ............................................... 16 6. SAMPLE CALCULATION ......................................................... 17 7. TEST DATA ............................................................................... 18 7.1 EFFECTIVE RADIATED POWER ...................................................................... 18 7.2 EQUIVALENT ISOTROPIC RADIATED POWER .............................................. 19 7.3 RADIATED SPURIOUS EMISSIONS ................................................................ 20 7.3.1 RADIATED SPURIOUS EMISSIONS (GSM850) .......................................... 20 7.3.2 RADIATED SPURIOUS EMISSIONS (WCDMA850) .................................... 21 7.3.3 RADIATED SPURIOUS EMISSIONS (HSUPA850) ...................................... 22 7.3.4 RADIATED SPURIOUS EMISSIONS (GSM1900) ........................................ 23 7.3.5 RADIATED SPURIOUS EMISSIONS (WCDMA1900) .................................. 24 7.3.6 RADIATED SPURIOUS EMISSIONS (HSUPA1900) .................................... 25 TRF-RF-210(04)140901 Page 3 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 1. GENERAL INFORMATION Applicant Name: Janam Technologies LLC Address: 100 Crossways Park West Suite 105, Woodbury, New York 11797 USA FCC ID : UTWXM5WA FCC Classification : Licensed Portable Transmitter Held to Ear (PCE) EUT : Mobile Computer Model Name : FCC: XM5 IC: XM5WA Add Model Name : NA Supplying power : DC 3.7V Antenna Information : Internal Antenna - Type: Built-In type Tx Frequency : GSM850: 824.2 ~ 848.8 MHz GSM1900: 1850.2 ~ 1909.8 MHz EDGE850: 824.2 ~ 848.8 MHz EDGE1900: 1850.2 ~ 1909.8 MHz WCDMA850: 826.4 ~ 846.6 MHz WCDMA1900: 1852.4 ~ 1907.6 MHz HSUPA850: 826.4 ~ 846.6 MHz HSUPA1900: 1852.4 ~ 1907.6 MHz Rx Frequency : GSM850: 869.2 ~ 893.8 MHz GSM1900: 1930.2 ~ 1989.8 MHz EDGE850: 869.2 ~ 893.8 MHz EDGE1900: 1930.2 ~ 1989.8 MHz WCDMA850: 871.4 ~ 891.6 MHz WCDMA1900: 1932.4 ~ 1987.6 MHz HSUPA850: 871.4 ~ 891.6 MHz HSUPA1900: 1932.4 ~ 1987.6 MHz Max. RF Output Power : GSM850: 2.296W ERP(33.61dBm) GSM1900: 1.239W EIRP(30.93dBm) EDGE850: 0.414W ERP(26.17dBm) EDGE1900: 0.459W EIRP(26.62dBm) WCDMA850: 0.247W ERP(23.93dBm) WCDMA1900: 0.361W EIRP(25.58dBm) HSUPA850: 0.229W ERP(23.59dBm) HSUPA1900: 0.344W EIRP(25.36dBm) Emission Designator(s) : GSM850: 249KGXW GSM1900: 247KGXW EDGE850: 235KG7W EDGE1900: 241KG7W WCDMA850: 4M15F9W WCDMA1900: 4M15F9W HSUPA850: 4M17F9W HSUPA1900: 4M17F9W TRF-RF-210(04)140901 Page 4 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 2. INTRODUCTION 2.1. EUT DESCRIPTION The Equipment Under Test(EUT) supports a GSM/GPRS/EDGE /WCDMA/HSUPA and Bluetooth, 2.4GHz, 5GHz WLAN, NFC. 2.2. MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 2.3. TEST FACILITY The 3m test site and conducted measurement facility used to collect the radiated data are located at the 38, Yurim-ro, 154beon-gil, Cheoin-gu, Yongin-si, Gyeonggi-do, Korea 449-935. The site is constructed in conformance with the requirements. - Semi anechoic chamber registration Number : 165783 (FCC) & 5740A-3 (IC) TRF-RF-210(04)140901 Page 5 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

U TWXMSWA 6914A—XMSWA DTNC1410—04626, DTINC1410—04629 DRTIFCC1411—1498 3. DESCRIPTION OF TESTS 3.1 ERP & EIRP (Effective Radiated Power & Equivalent Isotropic Radiated Power) Test Set—up D LJ 1 -l [ | wion 1| &6¥ Test Procedure — ANSI/TIA—603—C—2004 — Section 2.2.17 — KDB971168 v02r01 — Section 5.2.1 These measurements were performed at 3 &10 m test site. The equipment under test is placed on a non—conductive table 0.8—meters above a turntable which is flush with the ground plane and 3 meters from the receive antenna. Test setting 1. Set span to at least 1.5 times the OBW. 2. Set RBW = 1—5 % of the OBW, not to exceed 1 MHz. 3. Set VBW > 3 x RBW. 4. Set number of points in sweep > 2 * span / RBW. 5. Sweep time = auto couple. 6. Detector = RMS (power averaging). 7. If the EUT can be configured to transmit continuously (i.e., burst duty cycle > 98 %), then set the trigger to free run. 8. If the EUT cannot be configured to transmit continuously (i.e., burst duty cycle < 98 %), then use a sweep trigger with the level set to enable triggering only on full power bursts and configure the EUT to transmit at full power for the entire duration of each sweep. Ensure that the sweep time is less than or equal to the transmission burst duration. 9. Trace average at least 100 traces in power averaging (i.e., RMS) mode. 10. Compute the power by integrating the spectrum across the OBW of the signal using the instrument‘s band power measurement function, with the band limits set equal to the OBW band edges. If theinstrument does not have a band power function, then sum the spectrum levels (in linear power units) at intervalls equal to the RBW extending across the entire OBW of the spectrum. TRF—RF—210(04)140901 Page 6 / 25 Copyright © 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 The receive antenna height and turntable rotations were adjusted for the highest reading on the receive spectrum analyzer. A half-wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same receive spectrum analyzer reading. The conducted power at the terminal of the substitute antenna is measured. The ERP/EIRP is calculated using the following formula: ERP/EIRP = The conducted power at the substitute antenna`s terminal [dBm] + Substitute Antenna gain [dBd for ERP , dBi for EIRP] For readings above 1 GHz, the above procedure is repeated using horn antennas and the difference between the gain of the horn antenna and an isotropic antenna are taken into consideration. TRF-RF-210(04)140901 Page 7 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

U TWXMSWA 6914A—XMSWA DTNC1410—04626, DTINC1410—04629 DRTIFCC1411—1498 3.2 PEAK TO AVERAGE RATIO Test set—up Spectrum Analyzer Base Station se eSE | ”I ====== SE “E" Power Splitter | ATT EUT Test Procedure A peak to average ratio measurement is performed using the following procedure. ©CCDF Procedure — KDB971168 v02r01—Section 5.7.1 ._ Set resolution/measurement bandwidth > signal‘s occupied bandwidth Set the number of counts to a value that stabilizes the measured CCDF curve 3. Set the measurement interval as follows: 1) For continuous transmissions, set to 1 ms 2) For burst transmissions, employ an external trigger that is synchronized with the EUT burst timing sequence, or use the internal burst trigger with a trigger level that allows the burst to stabilize and set the measurement interval to a time that is less than or equal to the burst duration. Record the maximum PAPR level associated with a probaibility of 0.1% TRF—RF—210(04)140901 Page 8 / 25 Copyright © 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 ▣Alternate Procedure - KDB971168 v02r01-Section 5.7.2 Use one of the measurement procedures of the peak power and record as PPk. Use one of the measurement procedures of the average power and record as PAvg. Both the peak and average power levels must be expressed in the same logarithmic units (e.g., dBm). Determine the PAPR from: PAPR (dB) = PPk (dBm) - PAvg (dBm). - Peak Power Measurement 1. Set the RBW ≥ OBW 2. Set VBW ≥ 3 × RBW 3. Set span ≥ 2 x RBW 4. Sweep time = auto couple 5. Detector = peak 6. Ensure that the number of measurement points ≥ span/RBW. 7. Trace mode = max hold 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the peak amplitude level. - Average Power Measurement 1. Set span to at least 1.5 times the OBW. 2. Set RBW = 1-5% of the OBW, not to exceed 1 MHz. 3. Set VBW ≥ 3 x RBW. 4. Set number of points in sweep ≥ 2 × span / RBW. 5. Sweep time = auto-couple. 6. Detector = RMS (power averaging). 7. If the EUT can be configured to transmit continuously (i.e., burst duty cycle ≥ 98%), then set the trigger to free run. 8. If the EUT cannot be configured to transmit continuously (i.e., burst duty cycle < 98 %), then use a sweep trigger with the level set to enable triggering only on full power bursts and configure the EUT to transmit at full power for the entire duration of each sweep. Ensure that the sweep time is less than or equal to the transmission burst duration. 9. Trace average at least 100 traces in power averaging (i.e., RMS) mode. 10. Compute the power by integrating the spectrum across the OBW of the signal using the instrument’s band power measurement function, with the band limits set equal to the OBW band edges. If the instrument does not have a band power function, then sum the spectrum levels (in linear power units) at intervals equal to the RBW extending across the entire OBW of the spectrum. TRF-RF-210(04)140901 Page 9 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

U TWXMSWA 6914A—XMSWA DTNC1410—04626, DTINC1410—04629 DRTIFCC1411—1498 3.3 OCCUPIED BANDWIDTH. Test set—up Spectrum Analyzer BIFEE SEEEE'_E“ ie sene ooo nnnnnn nnnnnnn nnu{:} nnnnnn Inl:u:l:i:l:l smmfi @ &6 o Power Splitter ATT EUT Offset value information Frequency Offset Value Frequency Offset Value Hz dB Hz dB Note. 1: The offset values from EUT to Spectrum analyzer were measured and used for test. Offset value = Cable A + Splitter +ATT+ Cable B Test Procedure KDB971168 vO02r01—Section 4.2 The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power of a given emission. Test setting 1. The signal analyzer‘s automatic bandwidth measurement capability was used to perform the 99 % occupied bandwidth and the 26 dB bandwidth. The bandwidth measurement was not influenced by any intermediate power nulls in the fundamental emission. RBW =1~5 % of the expected OBW & VBW > 3 X RBW ~ 9 oo B J N Detector = Peak Trance mode = Max hold Sweep = Auto couple The trace was allowed to stabilize If necessary, step 2 ~ 6 were repeated after changing the RBW such that it would be within 1 ~5 % of the 99 % occupied bandwidth observed in step 6. TRF—RF—210(04)140901 Page 10 / 25 Copyright © 2014, DT&C Co., Ltd.

U TWXMSWA 6914A—XMSWA DTNC1410—04626, DTINC1410—04629 DRTIFCC1411—1498 3.4 BAND EDGE EMISSIONS AT ANTENNA TERMINAL. Test set—up Spectrum Analyzer Base Station & 00B ngggn 3 9600El o00 4~, Il: nnnnn ¢ Power Splitter I Offset value information Frequency Offset Value Frequency Offset Value Frequency Offset Value Hz dB Hz dB Hz dB Note. 1: The offset value from EUT to Spectrum analyzer was measured and used for test. Offset value = Cable A + Splitter +ATT+ Cable B Test Procedure — KDB971168 v02r01 — Section 6.0 All out of band emissions are measured by means of a calibrated spectrum analyzer. The EUT was setup to maximum output power at its lowest and highest channel with all modulations. The power of any spurious emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB Test setting Start and stop frequency were set such that the band edge would be placed in the center of the plot co ~ 0J oo BP @ N — Span was set large enough so as to capture all out of band emissions nearthe band edge RBW > 1 % of the emission VBW > 3 X RBW Detector = RMS & Trace mode = Max hold Sweep time = Auto couple or 1 s for band edge Number of sweep point > 2 X span / RBW The trace was allowed to stabilize Note 1: In the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed to demonstrate compliance with the out—of—band emissions limit. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. TRF—RF—210(04)140901 Page 11 / 25 Copyright © 2014, DT&C Co., Ltd.

U TWXMSWA 6914A—XMSWA DTNC1410—04626, DTINC1410—04629 DRTIFCC1411—1498 3.5 SPURIOUS AND HARMONIC EMISSIONS AT ANTENNA TERMINAL. Test set—up Spectrum Analyzer BIFEE SEZEE" 8 Esn o o0 s oo o& O 00 g 9. eoo 5 9 O Os00 flfl'fl{:} =wt §E Googo Inl:u:l:i:l:l smmmentiine Power Splitter Offset value information Frequency Offset Value Frequency Offset Value Frequency Offset Value Hz dB Hz dB Hz dB Note. 1: The offset value from EUT to Spectrum analyzer was measured and used for test. Offset value = Cable A + Splitter +ATT+ Cable B Test Procedure — KDB971168 v02r01 — Section 6.0 The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The EUT was setup to maximum output power at its low, middle, high channel with all bandwidths. The spectrum is scanned from 30 MHz up to a frequency including its 10°" harmonic. The power of any spurious emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB Test setting 1. RBW = 100 KHz or 1 MHz & VBW >3 X RBW ( Refer to Note 1) 2. Detector = RMS & Trace mode = Max hold 3. Sweep time = Auto couple 4. Number of sweep point > 2 X span / RBW 5.. The trace was allowed to stabilize Note 1: Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 100 kHz or greater for Part 22 and 1 MHz or greater for Part 24. TRF—RF—210(04)140901 Page 12 / 25 Copyright © 2014, DT&C Co., Ltd.

U TWXMSWA 6914A—XMSWA DTNC1410—04626, DTINC1410—04629 DRTIFCC1411—1498 3.6 RADIATED SPURIOUS EMISSIONS Test Set—up 4 i .IJ.‘.I t i # E4J I -. CC | wrfo 16 Test Procedure — ANSI/TIA—603—C—2004 — Section 2.2.12 — KDB971168 v02r01 — Section 5.8 These measurements were performed at 3 & 10m test site. The equipment under test is placed on a non—conductive table 0.8—meters above a turntable which is flush with the ground plane and 3 meters from the receive antenna. Test setting 1. RBW = 100 kHz for below 1 GHz and 1 MHz for above 1 GHz / VBW > 3 X RBW 2. Detector = Peak & Trace mode = Max hold 3. Sweep time = Auto couple 4. Number of sweep point > 2 X span / RBW 5. The trace was allowed to stabilize The receive antenna height and turntable rotations were adjusted for the highest reading on the receive spectrum analyzer. For radiated power measurements below 1 GHz, a half—wave dipole was substituted in place of the EUT. This dipole antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same spectrum analyzer reading. For radiated power measurements above 1 GHz, a Horn antenna was substituted in place of the EUT. This Horn antenna was driven by a signal generator and the level of the signal generator was adjusted to obtain the same spectrum analyzer reading. The difference between the gain of the horn and an isotropic antenna are taken into consideration. This measurement was performed with the EUT oriented in 3 orthogonal axis. TRF—RF—210(04)140901 Page 13 / 25 Copyright © 2014, DT&C Co., Ltd.

FCCID: UTWXXM5WA IC: 6914A A-XM5WA C1410-04626 DTNC 6, DTNC1410 0-04629 Report No.: DRTFCCC1411-149 98 3.7 7 FREQUE ENCY STAB BILITY / VARIATION VA N OF AMBIENT TEM MPERATUR RE Test Set-up Test Proced dure - ANSI/TIIA-603-C-2 2004 - KDB971 1168 v02r0 01 - Sectio on 9.0 The e frequencyy stability of o the transsmitter is m measured by: b a.) a Temperrature: The tem mperature is i varied frrom - 30 °CC to + 50 °C C using an n environm mental cham mber. b.) b Primary y Supply Voltage: V The primmary suppply voltage is varied ffrom 85 % to 115 % of the nom minal value for non hand- h carried battery an nd AC pow wered equ uipment. For F hand-carried, batttery-powe ered equipment, primaryy supply vo oltage is re educed to tthe battery y operating g end poinnt which sh hall be spe ecified by the m manufacturrer. Speecification n: The frequenccy stability shall be sufficient s to o ensure th ndamental emission stays within the hat the fun autthorized frequency block for Part 24. The freq quency sta ability of the transmitter sha all be ma aintained wwithin ± 0.0 000 25 % (±± 2.5 ppm)) of the cennter freque ency for Paart 22. Tim me Period and Proce edure: 1. 1 The carrrier freque ency of the e transmitte er is measu ured at roo om temperaature. (25 °C to provide a referencce) 2. 2 The equ uipment is turned on in a “standdby” condition for one minute bbefore appllying poweer to the transmitter. Measurement of the ccarrier freqquency of the transm mitter is made m within n one minute aafter applying power to the tran nsmitter. 3. 3 Frequen ncy measu urements are a made a at 10 °C inttervals ranging from -30 °C to +50 + °C. A perio od of at lea ast one half-hour is p provided too allow sta uipment at each abilization of the equ temperature levell. TRF-R RF-210(04)140901 Page 14 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 4. LIST OF TEST EQUIPMENT Cal.Date Next.Cal.Date Type Manufacturer Model (yy/mm/dd) (yy/mm/dd) S/N Spectrum Analyzer Agilent E4440A 14/10/21 15/10/21 US45303051 Vector Signal Generator Rohde Schwarz SMBV100A 14/01/07 15/01/07 255571 Signal Generator Rohde Schwarz SMF100A 14/07/01 15/07/01 102341 PreAmplifier Agilent 8449B 14/02/27 15/02/27 3008A00370 Amplifier HP 8447E 14/01/08 15/01/08 2945A02865 Dipole Antenna Schwarzbeck VHA9103 13/10/24 15/10/24 2116 Dipole Antenna Schwarzbeck VHA9103 14/04/01 16/04/01 2117 Dipole Antenna Schwarzbeck UHA9105 13/10/24 15/10/24 2261 Dipole Antenna Schwarzbeck UHA9105 14/04/01 16/04/01 2262 Bilog Antenna Schwarzbeck VULB9160 14/07/10 16/07/10 3151 HORN ANT ETS 3115 14/02/26 16/02/26 6419 HORN ANT ETS 3115 13/02/28 15/02/28 00021097 HORN ANT A.H.Systems SAS-574 13/03/20 15/03/20 154 HORN ANT A.H.Systems SAS-574 13/05/27 15/05/27 155 High-pass filter Wainwright WHKX1.0 14/09/11 15/09/11 9 High-Pass Filter Wainwright WHNX2.1 14/09/11 15/09/11 1 8960 Series 10 Wireless Agilent E5515C 14/02/28 15/02/28 GB43461134 Comms Test Set Universal Radio Rohde Schwarz CMU200 14/02/28 15/02/28 106760 Communication Tester Amplifier EMPOWER BBS3Q7ELU 14/09/12 15/09/12 1020 Thermo hygrometer BODYCOM BJ5478 14/05/13 15/05/13 120612-2 TRF-RF-210(04)140901 Page 15 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 5. SUMMARY OF TEST RESULTS FCC Part RSS Status Parameter Section(s) Section(s) Note 1 RSS-132 (5.4) 2.1046 Conducted Output Power CNote 2 RSS-133 (4.1) RSS-132 (5.4) 22.913(a) [SRSP-503(5.1.3)] Effective Radiated Power C 24.232(c) RSS-133 (6.4) Equivalent Isotropic Radiated Power [SRSP-510(5.1.2)] 22.917(a) 24.238(a) RSS-Gen (4.6.1) Occupied Bandwidth NA Note 3 2.1049 22.917(a) RSS-132 (5.5) Band Edge 24.238(a) NA Note 3 RSS-133 (6.5) Spurious and Harmonic Emissions at Antenna Terminal 2.1051 24.232(d) RSS-133 (6.4) Peak to Average Ratio NA Note 3 22.917(a) RSS-132 (5.5) 24.238(a) Radiated Spurious and Harmonic Emissions C RSS-133 (6.5) 2.1053 22.355 RSS-132 (5.3) 24.235 Frequency Stability NA Note 3 RSS-133 (6.3) 2.1055 Note 1: C=Comply NC=Not Comply NT=Not Tested NA=Not Applicable Note 2: Refer to RF Exposure Report (Test Report_SAR) Note 3: These test items were not performed because this device uses the granted module. (FCCID: QIPPHS8-P) Please refer to the test report of the granted module. The module test report number: - MDE_CINTE_1108_FCCd, MDE_CINTE_1108_FCCe (By 7Layers AG) The sample was tested according to the following specification: ANSI/TIA/EIA-603-C-2004 and KDB 971168 D01 v02r01 TRF-RF-210(04)140901 Page 16 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 6. SAMPLE CALCULATION A. Emission Designator GSM850 Emission Designator GSM1900 Emission Designator Emission Designator = 249KGXW Emission Designator = 247KGXW EDGE850 Emission Designator EDGE1900 Emission Designator Emission Designator = 235KG7W Emission Designator = 241KG7W WCDMA850 Emission Designator WCDMA1900 Emission Designator Emission Designator = 4M15F9W Emission Designator = 4M15F9W HSUPA850 Emission Designator HSUPA1900 Emission Designator Emission Designator = 4M17F9W Emission Designator = 4M17F9W Note: Emission designators of the granted module were used. TRF-RF-210(04)140901 Page 17 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7. TEST DATA 7.1 EFFECTIVE RADIATED POWER - GSM850 data Test Conditions(Power Step: 5) EUT LEVEL@ Antenna CH. Position TX ANTENNA ERP ERP Rated Pol. (H/V) TERMINAL Gain Note. (Axis) (dBm) (W) Voltage (dBm) (dBd) 824.2 128 Y V 30.44 1.19 31.63 1.457 DC 3.7V GSM 836.6 190 Y V 29.63 1.19 30.82 1.207 DC 3.7V GSM 848.8 251 Y V 32.42 1.19 33.61 2.296 DC 3.7V GSM 848.8 251 Y V 24.98 1.19 26.17 0.414 DC 3.7V EDGE - WCDMA850 data Test Conditions(TPC bits all set to “1”) EUT LEVEL@ Antenna CH. Position TX ANTENNA ERP ERP Rated Pol. (H/V) TERMINAL Gain Note. (Axis) (dBm) (W) Voltage (dBm) (dBd) 826.4 Y V 21.97 1.19 23.16 0.207 DC 3.7V - 4132 836.6 4183 X H 21.45 1.19 22.64 0.184 DC 3.7V - 846.6 4233 X H 22.74 1.19 23.93 0.247 DC 3.7V - - HSUPA850 data Test Conditions(TPC bits all set to “1”) EUT LEVEL@ Antenna CH. Position TX ANTENNA ERP ERP Rated Pol. (H/V) TERMINAL Gain Note. (Axis) (dBm) (W) Voltage (dBm) (dBd) 826.4 4132 Y V 21.48 1.19 22.67 0.185 DC 3.7V - 836.6 4183 X H 21.17 1.19 22.36 0.172 DC 3.7V - 846.6 4233 X H 22.40 1.19 23.59 0.229 DC 3.7V - NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 18 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.2 EQUIVALENT ISOTROPIC RADIATED POWER - GSM1900 data TEST CONDITIONS(Power Step: 0) EUT LEVEL@ Antenna CH. Position TX ANTENNA EIRP EIRP Rated Pol. (H/V) TERMINAL Gain Note. (Axis) (dBm) (W) Voltage (dBm) (dBi) 1850.2 Z V 21.80 8.89 30.69 1.172 DC 3.7V GSM 512 1880.0 Y H 21.89 8.92 30.81 1.205 DC 3.7V GSM 661 1909.8 Z V 21.97 8.96 30.93 1.239 DC 3.7V GSM 810 1909.8 Z V 17.66 8.96 26.62 0.459 DC 3.7V EDGE 810 - WCDMA1900 data Test Conditions(TPC bits all set to “1”) EUT LEVEL@ Antenna CH. Position Pol. TX ANTENNA EIRP EIRP Rated TERMINAL Gain Note. (Axis) (H/V) (dBm) (W) Voltage (dBm) (dBi) 1850.2 Z V 16.50 8.89 25.39 0.346 DC 3.7V - 9262 1880.0 Z V 16.31 8.92 25.23 0.333 DC 3.7V - 9400 1909.8 Z V 16.62 8.96 25.58 0.361 DC 3.7V - 9538 - HSUPA1900 data Test Conditions(TPC bits all set to “1”) EUT LEVEL@ Antenna CH. Position Pol. TX ANTENNA EIRP EIRP Rated TERMINAL Gain Note. (Axis) (H/V) (dBm) (W) Voltage (dBm) (dBi) 1850.2 Z V 15.98 8.89 24.87 0.307 DC 3.7V - 9262 1880.0 Z V 15.85 8.92 24.77 0.300 DC 3.7V - 9400 1909.8 Z V 16.40 8.96 25.36 0.344 DC 3.7V - 9538 NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 19 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.3 RADIATED SPURIOUS EMISSIONS 7.3.1 RADIATED SPURIOUS EMISSIONS (GSM850) LEVEL@ Substitute Correct Channel EUT Freq. POL ANTENNA Antenna Generator Result Limit Position (ERP) (MHz) (H/V) TERMINAL Gain Level (dBc) (dBc) (Axis) (dBm) (dBd) (dBm) 1648.47 Y H -61.85 6.50 -55.35 86.99 128 2472.40 Y H -63.96 7.53 -56.43 88.07 44.63 (1.457 W) - - - - - - - 1672.95 Y H -61.84 6.53 -55.31 86.13 190 2509.08 Y H -64.01 7.57 -56.44 87.26 43.82 (1.207 W) - - - - - - - 1697.79 Y H -61.80 6.56 -55.24 88.85 251 2546.48 Y H -62.09 7.59 -54.50 88.11 46.61 (2.296 W) - - - - - - - - Limit Calculation= 43 + 10 log10( ERP [W] ) [dBc] - No other spurious and harmonic emissions were reported greater than listed emissions above table. NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 20 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.3.2 RADIATED SPURIOUS EMISSIONS (WCDMA850) LEVEL@ Substitute Correct EUT Channel Freq. POL ANTENNA Antenna Generator Result Limit Position (ERP) (MHz) (H/V) TERMINAL Gain Level (dBc) (dBc) (Axis) (dBm) (dBd) (dBm) 1649.74 Y H -52.79 6.51 -46.28 69.44 4132 - - - - - - - 36.16 (0.207 W) - - - - - - - 1673.34 Y H -52.08 6.53 -45.55 68.19 4183 - - - - - - - 35.64 (0.184 W) - - - - - - - 1696.77 Y H -52.58 6.55 -46.03 69.96 4233 - - - - - - - 36.93 (0.247 W) - - - - - - - - Limit Calculation= 43 + 10 log10( ERP [W] ) [dBc] - No other spurious and harmonic emissions were reported greater than listed emissions above table. NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 21 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.3.3 RADIATED SPURIOUS EMISSIONS (HSUPA850) LEVEL@ Substitute Correct EUT Channel Freq. POL ANTENNA Antenna Generator Result Limit Position (ERP) (MHz) (H/V) TERMINAL Gain Level (dBc) (dBc) (Axis) (dBm) (dBd) (dBm) 1649.28 Z V -55.06 6.50 -48.56 71.23 4132 - - - - - - - 35.67 (0.185 W) - - - - - - - 1673.34 Z V -54.47 6.53 -47.94 70.30 4183 - - - - - - - 35.36 (0.172 W) - - - - - - - 1698.72 Z V -54.25 6.56 -47.69 71.28 4233 - - - - - - - 36.59 (0.229 W) - - - - - - - - Limit Calculation= 43 + 10 log10( ERP [W] ) [dBc] - No other spurious and harmonic emissions were reported greater than listed emissions above table. NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 22 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.3.4 RADIATED SPURIOUS EMISSIONS (GSM1900) LEVEL@ Substitute Correct Channel EUT Freq. POL ANTENNA Antenna Generator Result Limit Position (EIRP) (MHz) (H/V) TERMINAL Gain Level (dBc) (dBc) (Axis) (dBm) (dBi) (dBm) 3700.12 Y V -51.95 9.78 -42.17 72.86 512 - - - - - - - 43.69 (1.172 W) - - - - - - - - - - - - - - 3759.98 Y V -53.33 9.72 -43.61 74.42 661 - - - - - - - 43.81 (1.205 W) - - - - - - - - - - - - - - 3819.87 Y V -52.31 9.66 -42.65 73.58 810 - - - - - - - 43.93 (1.239 W) - - - - - - - - - - - - - - - Limit Calculation = 43 + 10 log10( EIRP [W] ) [dBc] - No other spurious and harmonic emissions were reported greater than listed emissions above table. NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 23 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.3.5 RADIATED SPURIOUS EMISSIONS (WCDMA1900) LEVEL@ Substitute Correct Channel EUT Freq. POL ANTENNA Antenna Generator Result Limit Position (EIRP) (MHz) (H/V) TERMINAL Gain Level (dBc) (dBc) (Axis) (dBm) (dBi) (dBm) 3701.80 Y H -42.38 9.78 -32.60 57.99 9262 - - - - - - - 38.39 (0.346W) - - - - - - - - - - - - - - 3759.03 Y H -43.57 9.72 -33.85 59.08 9400 - - - - - - - 38.23 (0.333W) - - - - - - - - - - - - - - 3817.78 X H -43.14 9.67 -33.47 59.05 9538 - - - - - - - 38.58 (0.361W) - - - - - - - - - - - - - - - Limit Calculation = 43 + 10 log10( EIRP [W] ) [dBc] - No other spurious and harmonic emissions were reported greater than listed emissions above table. NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 24 / 25 Copyright ○ C 2014, DT&C Co., Ltd.

FCCID: UTWXM5WA IC: 6914A-XM5WA DTNC1410-04626, DTNC1410-04629 Report No.: DRTFCC1411-1498 7.3.6 RADIATED SPURIOUS EMISSIONS (HSUPA1900) LEVEL@ Substitute Correct Channel EUT Freq. POL ANTENNA Antenna Generator Result Limit Position (EIRP) (MHz) (H/V) TERMINAL Gain Level (dBc) (dBc) (Axis) (dBm) (dBi) (dBm) 3701.92 X H -42.81 9.78 -33.03 57.90 9262 - - - - - - - 37.87 (0.307W) - - - - - - - - - - - - - - 3761.68 X H -44.02 9.72 -34.30 59.07 9400 - - - - - - - 37.77 (0.300W) - - - - - - - - - - - - - - 3820.42 X H -43.47 9.66 -33.81 59.17 9538 - - - - - - - 38.36 (0.344W) - - - - - - - - - - - - - - - Limit Calculation = 43 + 10 log10( EIRP [W] ) [dBc] - No other spurious and harmonic emissions were reported greater than listed emissions above table. NOTES: This EUT was tested under all configurations and the highest power is reported in GSM mode and WCDMA mode with HSDPA inactive at 12.2 kbps RMC and TPC bits set to “1” and in GSM mode using a Power Control Level of “0” in PCS Band and “5” in the Cellular Band. This EUT was tested with the fully charged battery. Also, we have done x, y, z planes in EUT and horizontal and vertical polarization of detecting antenna. The worst case data is reported. TRF-RF-210(04)140901 Page 25 / 25 Copyright ○ C 2014, DT&C Co., Ltd.


Document Created: 2019-10-15 10:05:24
Document Modified: 2019-10-15 10:05:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC