User Manual - A8190B IN100 (V3) Bored

FCC ID: U4A-SCYMCA1

Users Manual

Download: PDF
FCCID_3061105

IN100 with Aperio™ Technology Cylindrical Lock Installation Instructions A8189B 07/16 Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.


Table of Contents 1 Warning ....................................................................................3 2 General Description..................................................................4 3 Hardware Specifications..........................................................4 4 Electronic Specifications..........................................................4 5 Parts Breakdown......................................................................5 6 Lock Installation.......................................................................7 7 Operational Check .................................................................19 8 Lock LED Indications .............................................................20 Changes or modifications to this device not expressly approved by ASSA ABLOY 1 Warning could void the user’s authority to operate the equipment. FCC: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Industry Canada: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante. ! Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components: • Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door. • Leave components (reader and controller) protected in their respective anti-static bags until ready for installation • Do not touch pins, leads or solder connections on the circuit boards 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 2 General Description The SARGENT® IN100 mortise lock with Aperio™ Technology makes it easy and cost-effective to bring access control to more doors. It uses local wireless communication between the lock and an Aperio hub to connect to an access control system, eliminating the greatest cost and inconvenience of traditional access control – the wiring at the door. The IN100 utilizes HID® multiCLASS SE® technology, it supports heightened identity security and multiple credentials, including mobile access. All technology features are supported by the physical security of SARGENT ANSI/BHMA Grade 1 hardware - quality components that provide high security, performance and durability. 3 Hardware Specifications • Complete lockset with on-board memory • Lock furnished for 1-3/4” doors. • ADA compliant For other thicknesses, consult factory. • Easily retrofits existing (cylindrical lock) • ANSI/BHMA A156.25 Listed Grade 1 Compliant door preps • Outside lever controlled by contactless reader • Latch - 1/2” standard 3/4” throw fire-rated or mechanical cylinder double doors (optional) (41- prefix) • May be used for indoor and exterior applications • Deadlocking latch - Stainless steel, non handed 4 Electronic Specifications • Input Power: DC 9V, 1.5A (6 AA alkaline batteries) • Uses low-rate wireless personal area networks • Optional hard-power 12VDC to 24VDC (IEEE 802.15.4) • Multiple time zone and holiday access scheduling Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. • HID® multiCLASS SE™ technology offers support for the following credentials: • First-in unlock or automatic unlock configuration, • High Frequency (13.56 MHz): based on specified time schedule Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. • HID iCLASS® • Uses AES 128-bit wireless encryption* • HID iCLASS SE® (SIO-enabled) • Privacy button • HID iCLASS® Seos™ • HID MIFARE® SE • HID DESfire® EV1 SE *For specific security information, please contact • MIFARE Classic your local ASSA ABLOY Door Security Solutions • DESfire EV1 sales consultant or call 800-810-WIRE. • Low Frequency (125 kHz): • HID Prox® • NFC-enabled Mobile Phones ! To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only. Warning: SARGENT Mfg. Co. IN100 locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications. 07/31/16 4 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 5 Parts Breakdown 1 2 1 3 4 ITEM PART NUMBER/ORDER STRING DESCRIPTION COLOR/TRIM QTY 1 IN-100-EM0110G77-IP-B HID iCLASS , HID iCLASS SE (SIO-enabled), HID iCLASS Seos™, HID MIFARE ® ® ® ® Black 1 SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones IN-100-EM0110G77-IP-W HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE® White 1 SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones IN-100-EM0110G77-IP-MB-[xxx]* HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE® Black with metal trim 1 SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. IN-100-EM0110G77-IP-MW-[xxx]* HID iCLASS®, HID iCLASS SE® (SIO-enabled), HID iCLASS® Seos™, HID MIFARE® White with metal trim 1 SE, HID DESfire® EV1 SE, HID Prox®, NFC-enabled mobile phones Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. IN-100-EM0110G77-IPS-B All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 Black 1 IN-100-EM0110G77-IPS-W All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 White 1 IN-100-EM0110G77-IPS-MB-[xxx]* All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 Black with metal trim 1 IN-100-EM0110G77-IPS-MW-[xxx]* All credentials supported by the IP option plus MIFARE Classic and DESfire EV1 White with metal trim 1 2 IN-EM04 Mounting plate assembly 1 3 N/A AA battery (alkaline only) 6 4 IN-EM02-B Inside Escutcheon Assembly with Privacy Button - Black Plastic Black 1 IN-EM02-W Inside Escutcheon Assembly with Privacy Button - White Plastic White IN-EM02-MB-xxx* Inside Escutcheon Assembly with Privacy Button - Black Plastic & Metal Trim Black with metal trim IN-EM02-MW-xxx* Inside Escutcheon Assembly with Privacy Button - White Plastic & Metal Trim White with metal trim * Specify finish 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 5

IN100 Cylindrical Lock Parts Breakdown (Continued) 12 4 5 11 8* 7 6 10 5 9 4 3 2 1 PART NO./ORDER ITEM STRING DESCRIPTION QTY. 1 --- Outside Lever (Reference Catalog for Available Styles) 1 2 10-0043 Lever Retainer Key (In Screw Pack 10-2052) 1 Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 3 --- Cylinder Assembly (Reference Catalog for Available Cylinders) 1 4 --- Rose (Reference Catalog for Available Styles) 2 Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. 5 10-0792 Spacer Bushing 2 6 10-3049 Outside Rose Spring Assembly 1 7** 10-3452 Lockbody Assembly 10G77 (Standard Cylinder) 1 *Adapter Plate/Spacer (10-0847) is only shipped with orders 10-3453 Lockbody - LFIC (Removable Core) that specify 1-3/8” doors. 10-3454 Lockbody - SFIC 10-3455 Lockbody - Keso 10-3456 Lockbody - Medeco Keymark LFIC & Schlage Full Size Interchangeable Core 8 10-0847 Adapter Plate/Spacer (Only Included With 1-3/8” Thick Doors) 2 9 10-3192 Latch Assembly 1 10 10-2052 Screw Pack 2 11 10-3048 Inside Rose Spring Assembly 1 12 --- Inside Lever (Reference Catalog for Available Styles) 1 13 13 52-5374 Door Position Switch Kit (SPDT) 1 **The IN100 10G77 cylindrical lock supports Escape Return functionality. Tools Required: • #2 Phillips screwdriver • Flat head screwdriver • Security allen wrench 07/31/16 6 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 6 Lock Installation 1 Prepare Door A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. Fig. 1A LH LHRB RH RHRB Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel Hinges Right Reverse Bevel Open Inward Hinges Left Open Inward Hinges Right Open Outward Open Outward B. Prepare Door Prior to installation, all holes must be free of burrs, debris and sharp edges. Prepare door according to appropriate template (see website www.intelligentopenings.com). • Field Template: A8149 (ships with product) • Door Manufacturer’s Template: 4712 Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Outside of Door Inside of Door Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Through-bolt Holes Raceway for Power Raceway for Power (Optional) (Optional) External DPS Cable Hole Cable Hole holes Raceway for Lockbody Harness Lever Handle Raceway for Hole Through-bolt Holes Lockbody Harness Cylindrical Pocket and Latch Through-bolt Holes Holes Pre-drilled Tap Holes Fig. 1B Wood Door Preparation 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 7

IN100 Cylindrical Lock Centerline of 2 Install Strike Latch Front and Strike Install strike in the door frame (Fig. 2). (2) #8-32 x 3/4" Latch Screws Fig. 2 3 Install Latchbolt 1. Install latch with beveled bolt facing the strike. 2. Attach with two screws but DO NOT tighten completely at this time. Inside of Door See section 8 - Secure Lock to the Door. IMPORTANT: Latch bevel must match door bevel and deadlocking latch must stop on strike when door is closed. Strike Deadlocking Latch Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Fig. 3B Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Fig. 3A 4 Install Door Position Switch (DPS) 1. Push wires through raceway toward lock prep. 2. Push DPS firmly into place by hand. Inside of Door Note: DO NOT TAP SWITCH WITH ANY TOOL. 3. Install magnet into door frame. Push firmly into place by hand. See A7983. 4. To connect DPS to lock controller per diagram, refer to the wiring in Step #10 (Page 15). DPS (Door Position Switch) CAUTION: if DPS is not installed or is installed improperly, door status monitoring features will not function. Fig. 4 07/31/16 8 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 5 Lock Adjustments A. Lock Preset: • Lockbody holes: 12 and 6 o’clock (Fig. 5). The lock is shipped “preset” and does not require adjustment for 1-3/4” thick doors. Outside of Door Door thickness: 1-3/4” thick Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Preset Lock Fig. 5 NOTE: Adjusting for a thicker door requires removal of the outside lever, scalp and spacer bushing; see the following sections. If preset lock does not require adjustment, proceed to Section 7 - Install Lock. 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 9

IN100 Cylindrical Lock 6 Through-Bolt and Door Thickness Adjustment (If Required) A. Remove Outside Lever 1. Insert key, rotate 45° clockwise and hold. 2. Depress lever retainer with push pin tool (provided). 3. Pull lever outward. Outside of Door Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. B. How To Change Cylinder (If Necessary) Fig. 6A 1. With outside lever in hand, use standard pliers Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. to pull out cylinder retainer. 2. Remove key and cylinder from lever. 3. Insert new cylinder. 4. Secure by pressing cylinder retainer flush with the lever. Cylinder Retainer Cylinder Key Spacer Outside Lever Cylinder Fig. 6B Push Pin Tool Washers required for 30- prefix (10 Line Lever) to accept Schlage cylinder (no cylinder provided) 07/31/16 10 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock C. Through-Bolt and Door Thickness Adjustment 1. (If necessary) remove outside lever, scalp and spacer bushing (Fig. 6C). Spacer Bushing Scalp Outside Lever Fig. 6C 2. Rotate mounting plate to either align with through-bolt holes in Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. door, or adjust for proper door thickness (Fig. 6D). Refer to markings on through-bolt post (Fig. 6C Detail). Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. 1-3/4” Thick Doors 2” Thick Doors Fig. 6C Detail 3. Re-install spacer bushing to align with back of lever, scalp, and lever (Fig. 6D). Fig. 6D 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 11

IN100 Cylindrical Lock 7 Install Lock 1. From outside of door feed lockbody harness into the lockbody hole (Fig. 7A). For metal door: Feed harness through inside of door (not shown). 2. Continue to feed harness into raceway (towards top of door), exiting raceway hole on inside of door (Fig. 7B). 3. Slide lockbody into cross-bore hole from outside of door. 4. Lockbody must engage both the latch unit prongs and tail piece (Fig. 7C). IMPORTANT: • Door must remain open during installation (use door stop) • Lockbody must be centered in the door • Tuck excess wires into raceway to avoid pinching or damaging wires NOTE: Cable lengths exaggerated for illustrative purposes. Outside of Door Inside of Door Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Ground Ring Terminals Fig. 7B Detail Fig. 7A Fig. 7C Detail 07/31/16 12 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 8 Secure Lock to the Door 1. Slide inside rose assembly and spacer bushing over lockbody. 2. Position ground lug between (top) #10-32x1-1/4” through-bolt and rose assembly (Fig. 8A). NOTE: Proper placement of ground wire (Fig. 8B) will prevent Inside of Door pinching/damage to the ground wire. 3. Secure rose assembly with (2) #10-32x1-1/4” through-bolts. 4. Secure latch by fully tightening (2) #6 x 3/4” self-tapping screws (refer to previous section 3 - Install Latchbolt). NOTE: Cable lengths exaggerated for illustrative purposes. Ground Wire Fig. 8B Detail Fig. 8A Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. 9 Assemble Inside Trim 1. Verify spacer bushing is inserted horizontally and aligned with lever (Fig. 9). Inside of 2. Place rose over shaft of lockbody against the Door surface of the door; hand-tighten, turning clockwise. 3. Attach lever. Push until engaged. Rose Fig. 9 Inside lever 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 13

IN100 Cylindrical Lock 10 Outside Reader Installation 1. Orient the reader so the LED lens is at the top (Fig. 10A). 2. Feed the cable/connector through the door (from outside to inside). 3. Install the reader to the outside of door by aligning the mounting posts with the door preparation holes. Hold the reader flush against door while ensuring proper alignment. NOTE: Cable lengths exaggerated for illustrative purposes. Outside of Door LED Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reader Assembly with Harness Fig. 10A 07/31/16 14 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 10 Outside Reader Installation (Continued) 4. Feed the reader harness and DPS connectors through the inside mounting assembly (and gasket if required*). See Figure 11B. IMPORTANT: Do not run wires through bottom flange hole in plate (Fig. 11B, C) - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 11C). 5. Tuck excess cable into wire hole on inside of door. 6. Begin to secure the mounting assembly by partially tightening the (2) through-bolts on the inside of the door while ensuring proper alignment as you secure the reader (Fig. 11B). NOTE: Cable lengths exaggerated for illustrative purposes Gasket* Mounting Plate Through-bolt Door Position Switch Reader Harness Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Through-bolt Lockbody Harness Ground Ring Terminal Fig. 10C Fig. 10B 6. Secure ground lug with #6-32 machine screw (Fig. 10C). *Gasket is required for outdoor installations. Do not use gasket for fire-rated openings. If installing with gasket; separate gasket from mounting plate to feed cables/connectors through holes as indicated (Fig. 10B). Once cables/connectors are fed through, reattach gasket to mounting plate. 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 15

IN100 Cylindrical Lock 10 Outside Reader Installation (Continued) Installation of Connectors 9-24VDC DPS (4-pin) Power* CAUTION - Do not touch or allow debris to enter connector contacts. A Secure the following connectors to their respective terminals (Fig. 11D): A. Secure the 4-pin DPS connector. B. Secure the 10-pin lock body assembly connector. Ground B *NOTE: Optional 2-pin external 9-24VDC power connector. Lug IMPORTANT: Do not run wires through bottom hole in plate - it will damage wires and the controller connector. Route wires around flange, do not route wires through the flange hole (Fig. 11B, D). Fig. 11D Lock Body C. When all connections have been made, tuck excess cable (10-pin) into wire hole on inside of door. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Fully tighten Secure Mounting Plate D. Secure the mounting assembly while ensuring proper alignment of outside reader and tighten the (2) through-bolts on the inside of the door to secure the reader (Fig. 11E). E. Secure the 24-pin card reader connector (Fig. 11F). Fig. 11E Reader D (24-pin) Board-to-Board Connector Fig. 11F 07/31/16 16 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 11 Installation of Inside Component Assembly (Controller) 1. Insert top tabs of controller into slots on mounting plate (Fig. 12). 2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate. CAUTION: To avoid possible damage to board-to-board connectors, care should be taken when securing controller to mounting plate. If there is resistance when securing, detach controller to determine cause before re-attaching controller. Controller Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Fig. 12 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 17

IN100 Cylindrical Lock 13 Battery Installation 1. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly (Fig. 12). 2. After batteries are installed, there is a slight delay; then red and AA Batteries (6) green flash*, audible “beep” and lock motor will cycle. *See Section 8 - LED Indications for more information Fig. 12 14 Inside Cover Installation Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 1. Assemble cover by hooking top edge on inside Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. mounting plate. 2. Carefully press bottom of cover toward door without pinching or damaging wires. 3. Secure cover utilizing security allen wrench (provided). Inside Cover Security Allen Screw Fig. 13 07/31/16 18 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock 7 Operational Check 1. Insert key into cylinder and rotate (Fig. 14A). There should be no friction against lock case, wire harness or any other obstructions. 2. Check that the key retracts the latch. The key should rotate freely. 3. Try the inside lever; ensure it retracts latch. 4. Present a valid credential* (Fig. 14B) to unlock outside lever; turn lever handle to ensure latch retracts. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Fig. 14A Note: The credential should approach the inscription on the reader as indicated (Fig. 14B) to ensure the credential is read properly. Do not wave credential. Fig. 14B 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 19

IN100 Cylindrical Lock 8 LED Indications The communication hub has a single LED. It supports an optical scheme of red, green and yellow. The indication scheme is described by the figures below: Communication Hub LED indications Figure 1. Communication hub normal operation LED indication 2 sec. Online Green Aperio® lock Green + one offline red flash Green + two red flashes EAC offline Aperio® lock and Green + three EAC offline red flashes UHF Yellow + off, Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. communication fast flash Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Some special LED indication schemes are used during lock maintenance actions: 2 sec. Figure 2. Communication hub Pairing active Yellow + green maintenance LED indication Ethernet LED indication The LED on the AH40 communication hub indicates both the status of the Ethernet link level and ethernet communication: 2 sec. Figure 3. AH40 Communication hub Ethernet link Ethernet LED indication connected Green Ethernet Green + communication off fast flash *For more information, refer to Aperio Online Quick Installation Guide Document No: ST-001322-PF Date: 2015-12-23 07/31/16 20 1-800-810-WIRE • www.sargentlock.com • A8189B

IN100 Cylindrical Lock Lock LED indications The lock has three LEDs. They support an optical scheme with red, yellow and green. The indication scheme is described by the figures below: Figure 4. Lock normal operation LED indication EAC response Card + PIN access Enter PIN time One yellow flash after card, two (configurable) flashes before PIN (.125 second) Card access (configurable) One yellow flash (.25 second) Access granted, One green flash EAC offline or online (1 sec.) Access denied, One red flash EAC online (1 sec.) Force closed in remote Five yellow flashes and open/office mode one red flash (.25 second) Busy blink, com hub Continuous yellow flashes busy with other locks (.25 seconds every second) Access denied, Three red flashes EAC offline (.5 second each) Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Lock mechanism is Continuous red flashes blocked when closing 1) (.125 seconds every 1 sec.) Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Error in lock, Ten red flashes (.125 sec. each) maintenance required (Repeated every 10 sec. if lock can’t close) Ten red flashes (.125 sec. each) Tamper repeated every 10 sec. Time to replace Continuous yellow flashes the battery (.25 seconds every 5 sec.) Battery reached end Continuous red flashes of life, lock disabled (.25 seconds every 5 sec.) V3 USB cable detection Five yellow flashes action occurred (.25 second each) 1) When the lock mechanism is blocked (lock jammed) the lever must be turned to release the lock mechanism. Some special LED indication schemes are used during lock maintenance actions: Figure 5. Lock hub normal Enter configuration Five yellow flashes operation LED indication mode (.125 second each) 07/31/16 1-800-810-WIRE • www.sargentlock.com • A8189B 21

IN100 Cylindrical Lock Lock Self-Test LED indication After replacing batteries, a Power on Self Test (POST) is performed. The result is indicated using a series of red and green LED flashes as described by the figures below. LED indication after power up/replacement of the battery 8.3.1 Battery not fully charged Error in lock is an indication -10 quick (125ms) red blinks, that either new batteries are not at the right voltage or a backward battery has been installed; battery not fully charged; energy counter not reset or no Power on self-test done. Error in lock, Ten red flashes (.125 sec. each) maintenance required (Repeated every 10 sec. if lock can’t close) 8.3.2 Test pass 1 red (1s) + 1 green (1s), Power on self-test passed, see table below. POST Successful One red, one green flash Figure 6. Lock POST LED (1 second) indication 8.3.3 Test fail 1 red (1s) + 3 blinks (500ms, green or red), at least one test failed (red), see table below. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. If a fatal error is detected the lock will enter an Error state and continuously indicating fatal error and will not read cards nor unlock. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. 1 sec 0.5 sec 0.5 sec 0.5 sec FATAL ERROR CABLE ERROR MECHANICAL ERROR FATAL ERROR Tests core functionality. MCUs, memory and internal communication, etc. CABLE ERROR Tests communication between the different parts in the system, i.e. different boards connected with a wire. MECHANICAL ERROR Test related to moving parts of the lock. 07/31/16 22 1-800-810-WIRE • www.sargentlock.com • A8189B


SARGENT Manufacturing 100 Sargent Drive New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. A8189B - 07/16


Document Created: 2016-06-28 15:12:30
Document Modified: 2016-06-28 15:12:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC