Manual New Part1

FCC ID: TXTWC18CV

Users Manual

Download: PDF
FCCID_2984948

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 4 FCC Caution: The manufacturer is not responsible for radio particular installation. If this equipment does interference caused by unauthorized cause harmful interference to radio or modifications to this equipment. Such television reception, which can be determined modifications could void the user’s authority to by turning the equipment off and on, the user operate the equipment. is encouraged to try to correct the interference This device complies with Part 15 of the FCC by one or more of the following measures: Rules. Operation is subject to the following • Reorient or relocate the receiving antenna. two conditions: • Increase the separation between the 1) This device may not cause harmful equipment and receiver. interference, and • Connect the equipment into an outlet on a 2) This device must accept any interference circuit different from that to which the received, including interference that may receiver is connected. cause undesired operation. • Consult the dealer or an experienced These limits are designed to provide radio/TV technician for help. reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate Changes or modifications not expressly radio frequency energy and, if not installed approved by the party responsible for and used in accordance with the instructions, compliance could void the user’s authority to may cause harmful interference to radio operate the equipment. communications. However, there is no guarantee that interference will not occur in a Battery Care When batteries are not in batteries in a tool box or pocket with nails, ! WARNING tool or charger, keep them screws, keys, etc. Fire or injury may result. away from metal objects. For example, to DO NOT PUT BATTERIES INTO FIRE OR protect terminals from shorting DO NOT place EXPOSE TO HIGH HEAT. They may explode. Battery Disposal Do not attempt to disas- industry program to collect and recycle these ! WARNING semble the battery or batteries at the end of their useful life, when remove any component projecting from the taken out of service in the United States or battery terminals. Fire or injury may result. Canada. The RBRC program provides a Prior to disposal, protect exposed terminals convenient alterative to placing used Li-ion with heavy insulating tape to prevent shorting. batteries into the trash or the municipal waste Lithium-ion Batteries stream, which may be illegal in your area. If equipped with a lithium-ion battery, the Please call 1-800-8-BATTERY for information battery must be collected, recycled or disposed on Li-ion battery recycling and disposal of in an environmentally sound manner. bans/restrictions in your area, or return your “The EPA certified RBRC Battery batteries to a Skil/Bosch/Dremel Service Recycling Seal on the lithium-ion Center for recycling. Robert Bosch Tool (Li-ion) battery indicates Robert Corporation’s involvement in this program is Bosch Tool Corporation is part of our commitment to preserving our voluntarily participating in an environment and conserving our natural resources.” -4-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 5 FIG. 1 WIRELESS CHARGING BATTERY CABLE CONNECTOR CABLE SOCKET CHARGER ERROR INDICATOR (RED) CHARGE STATUS INDICATOR STANDBY INDICATOR (GREEN) CHARGING PLATFORM 12 V PLUG DRAW HOOK POWER SUPPLY Charger WC18CV Approximate Charging time for 2Ah battery: Input voltage: 290V 45min - 80%, 55min - 100% Output: 18V 3A Approximate Charging time for 4Ah battery: Power supply 1600A00AM7 (Designed for 75min - 80%, 95min - 100% use with 12V automotive DC system) Input voltage: 13.3 – 16.3V Output: 290V This charger will only charge the following Wireless charging battery ! WARNING packs: WCBAT612-WCBAT625. Voltage rating 18V For most up to date battery compatibility, please refer to www.boschtools.com -5-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 6 WC18H Holster Assembly The Bosch power supply and wireless Note: Refer to Fig. 2a. charger must be used in conjunction with 1. Remove Screw/Nut 1. the wireless charging holster WC18H. 2. Loosen the (2x) Screw 2. Add/change Holster Inserts 3. Remove installed inserts, pinching the bottom The holster is compatible with the following of inserts and pulling them from the holster. Bosch 18V Drill/Drivers and Impact Drivers through the use of specially-designed inserts 4. Position new inserts, matching left and right (see Fig. 2a). When purchased as a toolkit, the sides appropriately. Grooves in inserts and correct insert is shipped with the toolkit. When holster should align. purchased as a starter kit, the correct insert 5. Retighten (2x) Screw 2. should be selected from the Holster Insert 6. Reattach and tighten Screw/Nut 1. Compatibility table and installed according to the Installing the Charger into the Holster instructions below. 1. Slide the charger into the tray. (Fig. 2b) Be sure that the charger is fully inserted into the Holster-Compatible Tool Insert tray and that the power cord is routed out the back of the tray. DDH181 HDH181 2. Slide the tray into the holster. For 1 WCBAT612-WCBAT615 batteries, slide the DDH181X HDH181X tray guide rails into the upper tray guide slot. For WCBAT620-WCBAT625 batteries, slide DDS181 the tray guide rails into the lower tray guide DDS181A slot. Be sure to route the power cord through HDS181 the back of the holster. (Fig. 2a) HDS181A Removing the Charger from the Holster 2 DDS182 HDS182 1. Unplug the power cord from power supply DDS183 2. Remove the tray from the holster (Fig. 2a) HDS183 3. Remove the charger from the tray by first pulling charger up, then out of the tray (Fig. 25618 3 2b). IDH182 4 -6-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 7 NUT 1 FIG. 2a INSERT SCREW 1 HOLSTER TOOL SCREW 2 BATTERY RAIL BATTERY POWER CORD BATTERY GUIDE SLOT UPPER TRAY GUIDE SLOT LOWER TRAY CHARGER GUIDE SLOT TRAY BOLT 1 TRAY GUIDE RAIL FIG. 2b BATTERY GUIDE SLOT POWER CORD TRAY CHARGER -7-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 8 Installation The Bosch power supply and wireless charger must be used in conjunction with the wireless FIG.3 charging holster WC18H. The holster allows secure installation in the cargo areas of a HOLSTER vehicle, either fastened to a shelf or to a wall. WITH TOOL Users with Sortimo® van racking systems may opt to install the holster between standard SORTIMO® Sortimo® guide rails (Fig. 3). GUIDE RAIL Unplug power supply and ! WARNING charger from outlet before installation, storage, attempting any maintenance or cleaning. Such preventive safety measures reduce the risk of electric shock or fire. Do not use wireless ! WARNING charging frame WC18F in FIG.4 vehicle. Charging frame may break and lead to personal injury. Do not install power supply ! WARNING and wireless charging holster in vehicles without a permanent barrier between cargo and passenger areas. Do not install power supply and wireless PASSENGER PERMANENT CARGO charging holster in vehicle passenger area. AREA BARRIER AREA Power supply and wireless charging holster must be installed in vehicle cargo areas according to mounting instructions. Failure to properly install power supply and wireless charging holster in a vehicle with a permanent barrier between passenger and cargo areas could result in personal injury (Fig. 4). -8-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 9 Holster Side Mounting Instructions 3. Remove Bolt 1 (Fig. 2a) from bottom side The holster may be mounted to shelf or mounting hole. workbench side walls through the side 4. Attach holster to wall as shown in Fig. 5 mounting holes using the hardware provided Fasten holster securely to (Fig. 5). ! WARNING side walls. Holster not 1. Determine desired mounting position and securely fastened may become dislodged orientation. Holster may be mounted from and lead to personal injury either its left or right side. See Fig. 6a for Mount holster in only acceptable mounting positions. ! WARNING r e c o m m e n d e d 2. If mounting holes are not available, mark orientations. Failure to properly orient and pre-drill holes for side mounting bolts. holster may cause holster and/or power tool Side mounting bolt spacing is 10 inches to become dislodged and lead to personal (254mm). injury. FIG. 5 * Hardware included with holster WALL HOLSTER TOP WASHER* SIDE MOUNTING HOLE NUT* WASHER* m) 4m HOLE A (25 R 10" HOLE B SIDE MOUNTING BOLT* (2x) BOTTOM SIDE MOUNTING HOLE -9-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 10 Holster Side Mounting Orientation power tool to fall out of holster (Fig. 6b) . When side mounting the holster, use only the Do not mount the holster to a ceiling (Fig. orientations between 0° and 80° from 7a). horizontal relative to the bottom surface of Do not mount the holster to a wall using the the holster (Fig. 6a). Do not mount the bottom mounting holes (Fig. 7b). holster in orientations that may cause the FIG. 6a FIG. 6b HORIZONTAL LINE 0...80° VERTICAL LINE FIG. 7a CEILING FIG. 7b WALL -10-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 11 Bottom Mounting Instructions The holster may be mounted to flat surfaces FIG. 9 through the holes in its base (Fig 8). Do not mount holster upside down (Fig. 9). Fasten holster securely to ! WARNING horizontal surfaces with appropriate hardware. Holster not securely fastened may become dislodged and lead to personal injury. SCREW (4x) FIG. 8 HOLSTER HORIZONTAL SURFACE SCREW (4x) Power Supply Installation To avoid serious injury, the ! WARNING power supply must be 1. Determine desired mounting position and orientation. mounted securely to vehicle wall or rack storage system by means of the four 2. If mounting holes are not available, mark mounting holes on power supply housing. and pre-drill holes for the four mounting screws. 3. Attach power supply using suitable mounting screws (not included). 4. Securely connect charger cable connector to the power supply cable socket. -11-

2610041926 10-15 WC18CV_WC18C 10/7/15 9:07 AM Page 12 Operating Instructions The battery is supplied partially charged. battery can be charged at any time, without Completely charge the battery before using your reducing its service life. Interrupting the charging cordless tool for the first time. The lithium ion procedure does not damage the battery. Charger Indicators, symbols and meaning If the indicator lights are “OFF”, the charger is Continuous Error Indicator (red) not receiving power from power supply outlet. A continuous red error indicator Continuous Light Standby Indicator (green) shows that the battery or the charger temperature is outside of the A continuous green standby indicator permitted temperature range. As shows that the working voltage is soon as the permitted temperature range is applied and that the charger is ready reached, the charger automatically begins for use. charging. Flashing Charge Status Indicator Flashing Error Indicator (red) The charge status indicator A flashing red error indicator signals a flashes while charging. The different charger fault. See number of green bars indicate ‘Troubleshooting’ section. the charge level . All five bars green means that the battery is fully charged. The light then changes from flashing to continuous. Note: The tool and battery can be removed from the charger at any time and used. Wireless Charging Battery WIRELESS CHARGING STANDARD BATTERY SURFACE FIG. 10 CONTACTS -12-


Document Created: 2015-11-18 11:50:32
Document Modified: 2015-11-18 11:50:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC