Users Manual

FCC ID: SS3-HG3001606

Users Manual

Download: PDF
FCCID_3107570

： OSMO Mobile Osmo Mobile The OSMOTM Mobile is a professional mobile phone gimbal that stabilize your phone while in motion. Quick Start Guide Powerful features such as ActiveTrack and Motion Timelapse are available through the DJI GO app. V1.0          OSMO Mobile  www.dji.com           1 Mobile Phone Holder 9 Tilt Motor 14 Holder Lock Knob 2 Pan Motor 10 Adjustable Arm 15 Charging/Upgrade Port 3 Camera Status LED 11 Mobile Phone Detect 16 Trigger 4 Joystick Sensor 17 DJI Rosette Mount 5 Shutter Button 12 Adjustable Arm Lock 18 Lanyard Hole 6 Record Button Knob 19 Battery Cover 7 Power Switch 13 Roll Motor 8 System Status LED

1. Install the DJI GO App 3. Mount and Balance the Mobile Phone 4. Connect to the DJI GO App Specifications Search for ‘DJI GO’ on the App Store or Google Loosen the Holder Lock Knob, place the mobile dž Handle Play, and install the app on your mobile phone. phone in the mobile phone holder and tighten Dimensions 2.4 x 1.9 x 6.4 inch Enable Bluetooth on your mobile phone (61.8 x 48.2 x 161.5 mm) the knob to secure its position. Weight (battery included) 201 g dž Gimbal Name Zenmuse M1 Dimensions 125.06 x 109.15 x 90.98 mm (Folded) To Power On: Weight 300 g Pull down on the switch Consumption Static: 2.2 W; Dynamic: 3 W Pull down again > Sleep Angular Vibration Range ±0.03° Pull down and hold for 1.5 s > Power Off Controllable Range Pan: ±150° Roll: ±25° Tilt: -125° to +35° Mechanical Range Pan: ±165° Launch the DJI GO app and tap Enter Roll: -50° to +90° %+*(0 Camera View. Tap and then follow Tilt: -140° to +50° "QQ the instructions to connect to the Osmo Max Controllable Speed 120°/s Mobile Phone Width Range 2.31-3.34 inch (58.6-84.8 mm). Minimum width approx. that of the iPhone 5S, Maximum width ȕDJI GO supports iOS 8.0 (or later) and Activate the Osmo Mobile when using it for the approx. that of the Huawei Mate Android 4.3 (or later). first time. This requires an internet connection. 8 Max To balance the system, place the Osmo Mobile Internet and mobile phone on a level surface as shown. džWireless The system is balanced if the mobile phone Model Bluetooth Low Energy 4.0 remains level when released, balanced only by Intelligent Battery 2. Prepare the Battery the gimbal. 5. Controls dž Model HB01-522365 A. If the roll axis tilts to the left, loosen the Type LiPo Fully charge the battery before using it for the Adjustable Arm Lock Knob and pull out the Capacity 980 mAh first time to activate it. arm until the roll axis remains level. džUse the joystick to pan or tilt the mobile Energy 10.8 Wh B. If the roll axis tilts to the right, adjust the mobile phone. Voltage 11.1 V  $IBSHJOH5FNQFSBUVSF _ě ¡_¡' Insert the battery as shown. phone to the left until the roll axis levels out.  0QFSBUJOH5FNQFSBUVSF _ě " dž Record Button: Press once to start recording, and again to stop recording.  dž Shutter Button: Press once to take a  photo. Press and hold for burst capture. Battery Level dž Trigger High Low # Hold down to enable Lock Mode.  Tap twice to center the mobile phone. Tap three times to switch between the mobile phone’s front and rear cameras.  For more information, read the User Manual: www.dji.com/product/osmo-mobile ȕDo not power on the Osmo Mobile without a DJI GO advanced features: ČThis Quick Start Guide is subject to change without prior notice. mobile phone. The Osmo Mobile will not work if no To charge the Osmo Mobile, device is detected by its sensor. OSMOTM is a trademark of DJI. connect the USB adapter (not ȕIt is important to balance the mobile phone in order Copyright © 2016 DJI All Rights Reserved. included) to the charging port to achieve optimal performance. The Osmo Mobile using the provided power cable. should only be balanced when powered off. ActiveTrack Motion Timelapse Printed in China

FCC Compliance Notice： This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC RSS Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Information: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet appareil est conforme aux limitesd'exposition de rayonnement RF IC établiespour un environnement non contrôlé. Cetémetteur ne doit pas être co-implanté oufonctionner en conjonction avec toute autreantenne ou transmetteur. CAN ICES-3 (B)/NMB-3(B) EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby dec compliance with the essential requirements and other relevant provisions of the R&TTE Directive. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro-compliance EU contact address: DJI GmbH, Industrie Strasse. 12, 97618, Niederlauer, Germany


Document Created: 2017-12-13 02:55:41
Document Modified: 2017-12-13 02:55:41
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC