Test Report

FCC ID: SK9AMI-5

Test Report

Download: PDF
FCCID_1083261

Certification Test Report FCC ID: SK9AMI-5 IC: 864G-AMI5 FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-210 ACS Report Number: 09-0071-15C-DTS Manufacturer: Itron Electricity Metering, Inc. Model: CVSO-B Test Begin Date: December 17, 2008 Test End Date: March 11, 2009 Report Issue Date: March 12, 2009 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 200612-0 This report is not be used to claim certification, approval, or endorsement by NVLAP, NIST or any government agency. Prepared by: Reviewed by: Ken Rivers Kirby Munroe Wireless Certifications Technician Director, Wireless Certifications ACS, Inc. ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 26 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Table of Contents 1.0 General 3 1.1 Purpose 3 1.2 Product Description 3 1.2.1 General 3 1.2.2 Intended Use 3 1.3 Test Methodology and Considerations 3 2.0 Test Facilities 4 2.1 Location 4 2.2 Laboratory Accreditations/Recognitions/Certifications 4 2.3 Radiated Emissions Test Site Description 5 2.3.1 Semi-Anechoic Chamber Test Site 5 2.3.2 Open Area Tests Site (OATS) 6 2.4 Conducted Emissions Test Site Description 7 3.0 Applicable Standards and References 7 4.0 List of Test Equipment 8 5.0 Support Equipment 9 6.0 EUT Setup Block Diagram 9 7.0 Summary of Tests 10 7.1 Antenna Requirement 10 7.2 Power Line Conducted Emissions 10 7.2.1 Test Methodology 10 7.2.2 Test Results 10 7.3 Radiated Emissions (Unintentional Radiation) 11 7.3.1 Test Methodology 11 7.3.2 Test Results 11 7.4 6dB / 99% Bandwidth 12 7.4.1 Test Methodology 12 7.4.1 Test Results 12 7.5 Peak Output Power 16 7.5.1 Test Methodology 16 7.5.2 Test Results 16 7.6 Band-Edge Compliance and Spurious Emissions 18 7.6.1 Band-Edge Compliance 18 7.6.1.1 Test Methodology 18 7.6.1.2 Test Results 18 7.6.2 Conducted Spurious Emissions 19 7.6.2.1 Test Methodology 19 7.6.2.2 Test Results 19 7.6.3 Radiated Spurious Emissions 23 7.6.3.1 Test Methodology 23 7.6.3.2 Duty Cycle Correction 23 7.6.3.3 Test Results 23 7.6.3.4 Sample Calculation 24 7.7 Power Spectral Density 25 7.7.1 Test Methodology 25 7.7.2 Test Results 25 8.0 CONCLUSION 26 Additional Exhibits Included In Filing Internal Photographs External Photographs Installation/Users Guide Test Setup Photographs Theory of Operation Product Labeling System Block Diagram RF Exposure – MPE Calculations Schematics 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 1.0 GENERAL 1.1 Purpose The purpose of this report is to demonstrate compliance with Part 15 Subpart C of the FCC’s Code of Federal Regulations and Industry Canada’s Radio Standards Specification RSS-210. 1.2 Product Description 1.2.1 General The CENTRON OpenWay meter is used for measuring electrical energy consumption. The CENTRON OpenWay meter incorporates a two-piece design combining a base metrology with a variety of OpenWay registers or options. The metrology portion of the meter contains all measurement circuitry and calibration information, while the personality modules contain the register functionality and communication mediums. Each version of the meter is distinguished by the various personality modules or option boards that mount to the standard meter metrology base. For the purpose of this report, only the CENTRON OpenWay CVSOR-B meter was evaluated. The CVSOR-B register board contains (1) 900 MHz LAN frequency hopping spread spectrum radio and (1) 2.4 GHz direct sequence spread spectrum Zigbee radio. Manufacturer Information: Itron Electricity Metering, Inc. 313 North Highway 11 West Union, SC 29696 Test Sample Serial Number(s): 58383154 (RF Conducted Measurements) 58383151 (Radiated & AC Power line Conducted Emissions) 58116518 (Radiated & AC Power line Conducted Emissions) Test Sample Condition: The test samples were provided in good working order with no visible defects. Detailed photographs of the EUT are filed separately with this filing. 1.2.2 Intended Use The CENTRON OpenWay meter is used for measuring electrical energy consumption. 1.3 Test Methodology and Considerations This device is considered a composite device by definition. The 900 MHz LAN radio and the 2.4 GHz Zigbee radios operate under CFR 47 Part 15.247 and IC RSS-210. This report addresses the 2400 MHz Zigbee radio only. Two meter form factors, the 3S and 4S, were evaluated and data presented in this report for each. The difference in the meter forms are in the metrology section with no differences in the RF. ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 3

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 2.0 TEST FACILITIES 2.1 Location The radiated and conducted emissions test sites are located at the following address: Advanced Compliance Solutions 5015 B.U. Bowman Drive Buford, GA 30518 Phone: (770) 831-8048 Fax: (770) 831-8598 2.2 Laboratory Accreditations/Recognitions/Certifications The Semi-Anechoic Chamber Test Site, Open Area Test Site (OATS) and Conducted Emissions Site have been fully described, submitted to, and accepted by the FCC, Industry Canada and the Japanese Voluntary Control Council for Interference by information technology equipment. In addition, ACS is compliant to ISO 17025 as certified by the National Institute of Standards and Technology under their National Voluntary Laboratory Accreditation Program. The following certification numbers have been issued in recognition of these accreditations and certifications: FCC Registration Number: 894540 Industry Canada Lab Code: IC 4175 VCCI Member Number: 1831 ƒ VCCI OATS Registration Number R-1526 ƒ VCCI Conducted Emissions Site Registration Number: C-1608 NVLAP Lab Code: 200612-0 ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 4

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 2.3 Radiated Emissions Test Site Description 2.3.1 Semi-Anechoic Chamber Test Site The Semi-Anechoic Chamber Test Site consists of a 20’ x 30’ x 18’ shielded enclosure. The chamber is lined with Toyo Ferrite Grid Absorber, model number FFG-1000. The ferrite tile grid is 101 x 101 x 19mm thick and weighs approximately 550 grams. These tiles are mounted on steel panels and installed directly on the inner walls of the chamber. The turntable is 150cm in diameter and is located 160cm from the back wall of the chamber. The chamber is grounded via 1 - 8’ copper ground rod, installed at the center of the back wall, it is bound to the ground plane using 3/4" stainless steel braided cable. The turntable is all steel, flush mounted table installed in an all steel frame. The table is remotely operated from inside the control room located 25’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Behind the turntable is a 3’ x 6’ x 4’ deep shielded pit used for support equipment if necessary. The pit is equipped with 1 - 4” PVC chases from the turntable to the pit that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. A diagram of the Semi-Anechoic Chamber Test Site is shown in Figure 2.3-1 below: 3 Meters 5 Feet Diameter 20 Feet 30 Feet Figure 2.3-1: Semi-Anechoic Chamber Test Site ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 5

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 2.3.2 Open Area Tests Site (OATS) The open area test site consists of a 40’ x 66’ concrete pad covered with a perforated electro- plated galvanized sheet metal. The perforations in the sheet metal are 1/8” holes that are staggered every 3/16”. The individual sheets are placed to overlap each other by 1/4” and are riveted together to provide a continuous seam. Rivets are spaced every 3” in a 3 x 20 meter perimeter around the antenna mast and EUT area. Rivets in the remaining area are spaced as necessary to properly secure the ground plane and maintain the electrical continuity. The entire ground plane extends 12’ beyond the turntable edge and 16’ beyond the antenna mast when set to a 10 meter measurement distance. The ground plane is grounded via 4 - 8’ copper ground rods, each installed at a corner of the ground plane and bound to the ground plane using 3/4" stainless steel braided cable. The turntable is an all aluminum 10’ flush mounted table installed in an all aluminum frame. The table is remotely operated from inside the control room located 40’ from the range. The turntable is electrically bonded to the surrounding ground plane via steel fingers installed on the edge of the turn table. The steel fingers make constant contact with the ground plane during operation. Adjacent to the turntable is a 7’ x 7’ square and 4’ deep concrete pit used for support equipment if necessary. The pit is equipped with 5 - 4” PVC chases from the pit to the control room that allow for cabling to the EUT if necessary. The underside of the turntable can be accessed from the pit so cables can be supplied to the EUT from the pit. The pit is covered with 2 sheets of 1/4" diamond style re-enforced steel sheets. The sheets are painted to match the perforated steel ground plane; however the underside edges have been masked off to maintain the electrical continuity of the ground plane. All reflecting objects are located outside of the ellipse defined in ANSI C63.4. A diagram of the Open Area Test Site is shown in Figure 2.3-2 below: 10 3 Meters 40 7x7x4 Pit 66 Feet Figure 2.3-2: Open Area Test Site ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 6

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 2.4 Conducted Emissions Test Site Description The AC mains conducted EMI site is located in the main EMC lab. It consists of an 8’ x 8’ solid aluminum horizontal group reference plane (GRP) bonded every 3” to an 8’ X 8’ vertical ground plane. The site is of sufficient size to test table top and floor standing equipment in accordance with section 6.1.4 of ANSI C63.4. A diagram of the room is shown below in figure 4.1.3-1: Vertical Ground Plane (8’ x 8’) Non-Conductive EUT Table (1m x 1.5m x .8m) .4 Meters .8 Meters Horizontal Ground Plane (8’ x 8’) LISN Figure 2.4-1: AC Mains Conducted EMI Site 3.0 APPLICABLE STANDARD REFERENCES The following standards were used: ™ ANSI C63.4-2003: Method of Measurements of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the 9KHz to 40GHz ™ US Code of Federal Regulations (CFR): Title 47, Part 2, Subpart J: Equipment Authorization Procedures, 2008 ™ US Code of Federal Regulations (CFR): Title 47, Part 15, Subpart C: Radio Frequency Devices, Intentional Radiators, 2008 ™ FCC KDB Publication No. 558074 - Guidance on Measurements for Digital Transmission Systems (47 CFR 15.247), March 2005 ™ Industry Canada Radio Standards Specification: RSS-210 - Low-power License-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment, Issue 7 June 2007 ™ Industry Canada Radio Standards Specification: RSS-GEN – General Requirements and Information for the Certification of Radiocommunication Equipment, Issue2, June 2007. ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 7

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 4.0 LIST OF TEST EQUIPMENT The calibration interval of test equipment is annually or the manufacturer’s recommendations. Where the calibration interval deviates from the annual cycle based on the instrument manufacturer’s recommendations, it shall be stated below. Table 4-1: Test Equipment Equipment Calibration Information ACS# Mfg. Eq. type Model S/N Cal. Due Spectrum 1 Rohde & Schwarz Analyzers ESMI - Display 833771/007 09-19-2009 Spectrum 2 Rohde & Schwarz Analyzers ESMI-Receiver 839587/003 09-19-2009 22 Agilent Amplifiers 8449B 3008A00526 10-22-2009 25 Chase Antennas CBL6111 1043 08-22-2009 Spectrum 30 Technologies Antennas DRH-0118 970102 05-07-2009 40 Electro-Metrics Antennas 3104 3211 01-22-2010 152 EMCO LISN Feb-25 9111-1905 03-26-2009 Chamber EMI 167 ACS Cable Set Cable Set 167 02-06-2010 02-10-2010 168 Hewlett Packard Attenuators 11947A 44829 (See Note2) 193 ACS Cable Set OATS cable Set 193 01-05-2010 211 Eagle Filters C7RFM3NFNM HLC-700 01-05-2010 213 TEC Amplifiers PA 102 44927 12-22-2009 277 Emco Antennas 93146 9904-5199 09-09-2009 02-04-2010 282 Microwave Circuits Filters H2G020G4 74541 (See Note1) Spectrum 283 Rohde & Schwarz Analyzers FSP40 1000033 09-19-2009 SMRE-200W- 11-24-2009 291 Florida RF Cables Cables 12.0-SMRE None (See Note1) SMR-290AW- 11-24-2009 292 Florida RF Cables Cables 480.0-SMR None (See Note1) 321 Hewlett Packard Amplifiers HPC 8447D 1937A02809 10-08-2009 324 ACS Cables Belden 8214 07-28-2009 07-28-2009 331 Microwave Circuits Filters H1G513G1 31417 (See Note1) 04-08-2009 337 Microwave Circuits Filters H1G513G1 282706 (See Note1) 338 Hewlett Packard Amplifiers 8449B 3008A01111 10-22-2009 07-08-2009 339 Aeroflex/Weinschel Attenuators AS-18 7142 (See Note2) SMS-200AW- 02-05-2010 422 Florida RF Cables 72.0-SMR 805 (See Note1) Note1: Items characterized on an annual cycle. The date shown indicates the next characterization due date. Note2: Items verified on an annual cycle. The date shown indicates the next verification due date. ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 8

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 5.0 SUPPORT EQUIPMENT Table 5-1: Support Equipment Item Equipment Type Manufacturer Model Number Serial Number 1 Meter Base Enclosure Milbank 3R NA 2 CENTRON II meter Itron Electricity Metering C2SO-B 58383154 3 CENTRON II meter Itron Electricity Metering CVSO-B 58383151 4 CENTRON II meter Itron Electricity Metering CSVO-B 58116518 5 Transformer Sagamo Weston Type T-6A 325827 002 6.0 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM Spectrum Analyzer 3-4 *50 Ohm connection to 2 Spectrum Analyzer - Used for conducted measurements only. 1 1 240 VAC 240 VAC 5 5 Configuration 1 Configuration 2 120 VAC 120 VAC Figure 6-1: EUT Test Setup Note1: The 3S meter form can operate at 120 – 240 VAC. Emissions data presented in this report represents worst case with respect to input voltage. For operation at 120 VAC, the transform (item 5) was removed. Note2: The 4S meter form operates at 240 VAC only. ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 9

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.0 SUMMARY OF TESTS Along with the tabular data shown below, plots were taken of all signals deemed important enough to document. 7.1 Antenna Requirement – FCC: Section 15.203 The antenna is half wavelength slot antenna which can not be altered without destroying the device. This device is also professionally installed therefore meeting the requirements of CFR 47 Part 15.203. 7.2 Power Line Conducted Emissions – FCC: Section 15.207 IC: RSS-Gen 7.2.2 7.2.1 Test Methodology ANSI C63.4 sections 6 and 7 were the guiding documents for this evaluation. Conducted emissions were performed from 150kHz to 30MHz with the spectrum analyzer’s resolution bandwidth set to 9kHz and the video bandwidth set to 30kHz. The calculation for the conducted emissions is as follows: Corrected Reading = Analyzer Reading + LISN Loss + Cable Loss Margin = Applicable Limit - Corrected Reading 7.2.2 Test Results Results of the test are shown below in and Tables 7.2-1 and 1.2-2. Table 7.2-1: Line 1 Conducted EMI Results - 3S (240 VAC) Total Uncorrected Reading Corrected Level Limit Margin Frequency Correction (dBuV) (dBuV) (dBuV) (dB) Line (MHz) Factor (dB) Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Line 1 0.15 39.8 34.6 9.81 49.61 44.41 66.00 56.00 16.4 11.6 GND 0.26 39 34.3 9.81 48.81 44.11 61.43 51.43 12.6 7.3 GND 0.44 33.8 27.3 9.90 43.70 37.20 57.06 47.06 13.4 9.9 GND 0.59 33.1 28.1 9.90 43.00 38.00 56.00 46.00 13.0 8.0 GND 1.59 24.3 19.8 9.90 34.20 29.70 56.00 46.00 21.8 16.3 GND 2.16 11.8 5.9 9.90 21.70 15.80 56.00 46.00 34.3 30.2 GND 23.15 4.1 0.4 10.30 14.40 10.70 60.00 50.00 45.6 39.3 GND Line 2 0.15 39.6 34.5 9.81 49.41 44.31 66.00 56.00 16.6 11.7 GND 0.22 39.1 34.5 9.80 48.90 44.30 62.82 52.82 13.9 8.5 GND 0.47 37.1 32.9 9.90 47.00 42.80 56.51 46.51 9.5 3.7 GND 0.64 35.3 31.3 9.90 45.20 41.20 56.00 46.00 10.8 4.8 GND 1.59 27.4 23.1 9.90 37.30 33.00 56.00 46.00 18.7 13.0 GND 2.62 22.4 18.4 9.90 32.30 28.30 56.00 46.00 23.7 17.7 GND Table 7.2-2: Line 1 Conducted EMI Results - 4S (240 VAC) Total Uncorrected Reading Corrected Level Limit Margin Frequency Correction (dBuV) (dBuV) (dBuV) (dB) Line (MHz) Factor (dB) Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Quasi-Peak Average Line 1 0.18 38.8 34.3 9.82 48.62 44.12 64.49 54.49 15.9 10.4 GND 0.3 38.4 34.7 9.80 48.20 44.50 60.24 50.24 12.0 5.7 GND 0.46 37.6 34.2 9.90 47.50 44.10 56.69 46.69 9.2 2.6 GND 0.69 34.9 31.6 9.90 44.80 41.50 56.00 46.00 11.2 4.5 GND 1.6 27.5 24.1 9.90 37.40 34.00 56.00 46.00 18.6 12.0 GND 2.79 22.4 18.9 9.90 32.30 28.80 56.00 46.00 23.7 17.2 GND Line 2 0.18 39.3 35.2 9.82 49.12 45.02 64.49 54.49 15.4 9.5 GND 0.3 38 34.5 9.80 47.80 44.30 60.24 50.24 12.4 5.9 GND 0.41 37.7 33.8 9.90 47.60 43.70 57.65 47.65 10.0 3.9 GND 0.61 35.7 31.8 9.90 45.60 41.70 56.00 46.00 10.4 4.3 GND 1.6 23.5 23.7 9.90 33.40 33.60 56.00 46.00 22.6 12.4 GND 2.85 22.8 19.2 9.90 32.70 29.10 56.00 46.00 23.3 16.9 GND ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 10

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.3 Radiated Emissions – FCC: Section 15.109(Unintentional Radiation) IC: RSS-210 2.6 7.3.1 Test Methodology Radiated emissions tests were performed over the frequency range of 30MHz to 12.5GHz. Measurements of the radiated field strength were made at a distance of 3m from the boundary of the equipment under test (EUT) and the receiving antenna. The antenna height was varied from 1m to 4m so that the maximum radiated emissions level would be detected. Radiated measurements above 30MHz and below 1GHz were made with the Spectrum Analyzer’s resolution bandwidth set to 120 KHz using a Quasi-peak detector. Above 1GHz, peak and average measurements are taken with the RBW and VBW were set to 1MHz and 3MHz respectively. 7.3.2 Test Results Results of the test are given in Tables 7.3-1 and 7.3-2 below: Table 7.3-1: Radiated Emissions Tabulated Data – 3S (240 VAC) Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 276.488 --------- 31.85 H -11.54 --------- 20.31 -------- 46.0 --------- 25.69 315.868 --------- 35.02 V -11.12 --------- 23.90 -------- 46.0 --------- 22.10 333.906 --------- 36.65 V -10.35 --------- 26.30 -------- 46.0 --------- 19.70 387.085 --------- 17.60 H -8.17 --------- 9.43 -------- 46.0 --------- 36.57 608.277 --------- 23.72 V -3.62 --------- 20.10 -------- 46.0 --------- 25.90 949.416 --------- 8.76 V 3.37 --------- 12.13 -------- 46.0 --------- 33.87 * Note: All emissions above 949.416 MHz were attenuated below the permissible limit. Table 7.3-2: Radiated Emissions Tabulated Data – 4S (240 VAC) Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg 120 --------- 37.43 V -12.60 --------- 24.83 -------- 43.5 --------- 18.67 288.004 --------- 24.05 H -11.34 --------- 12.71 -------- 46.0 --------- 33.29 382.755 --------- 15.62 H -8.43 --------- 7.19 -------- 46.0 --------- 38.81 608.273 --------- 26.08 V -3.62 --------- 22.46 -------- 46.0 --------- 23.54 737.298 --------- 28.16 H -1.45 --------- 26.71 -------- 46.0 --------- 19.29 939.65 --------- 8.41 V 2.88 --------- 11.29 -------- 46.0 --------- 34.71 1315.977 --------- 48.75 H -8.58 --------- 40.17 74.0 54.0 --------- 13.83 * Note: All emissions above 1315.977 MHz were attenuated below the permissible limit. ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 11

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.4 6dB / 99% Bandwidth – FCC: Section 15.247(a)(2) IC: RSS-210 A8.2(a) 7.4.1 Test Methodology The 6dB bandwidth was measured in accordance with the FCC KDB Publication No. 558074 “Guidance on Measurements for Digital Transmission Systems (47 CFR 15.247)”. The RBW of the spectrum analyzer was set to 100 kHz and VBW 300 kHz. Span was set large enough to capture the entire emissions and >> RBW. The 99% occupied bandwidth was measured with the spectrum analyzer span set to 2 to 3 times the estimated bandwidth of the emission. The RBW was to ≥ 1% of the estimated emission bandwidth. The trace was set to max hold with a peak detector active. The occupied bandwidth measurement function of the analyzer was used for the 99% bandwidth. 7.4.2 Test Results Results are shown below in table 7.4.2-1 and figure 7.4.2-1 to 7.4.2-6: Table 7.4.2-1: 6dB / 99% Bandwidth Frequency 6dB Bandwidth 99% Bandwidth [MHz] [MHz] [MHz] 2405 1.62 2.40 2440 1.59 2.34 2475 1.57 2.32 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 13.19 dBm Ref 20 dBm Att 40 dB SWT 2.5 ms 2.405230000 GHz 20 Offset 10 dB ndB [T1] 6.00 dB 1 BW 1.620000000 MHz Temp 1 [T1 ndB] A 10 T1 T2 6.99 dBm 1 PK 2.404160000 GHz MAXH 0 Temp 2 [T1 ndB] 7.04 dBm LVL 2.405780000 GHz -10 -20 -30 -40 -50 -60 -70 -80 Center 2.405 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 14:34:21 Figure 7.4.2-1: 6dB Bandwidth Plot – Low Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 12

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 12.48 dBm Ref 20 dBm Att 40 dB SWT 2.5 ms 2.439710000 GHz 20 Offset 10 dB ndB [T1] 6.00 dB 1 BW 1.590000000 MHz Temp 1 [T1 ndB] A 10 T1 T2 6.47 dBm 1 PK 2.439160000 GHz MAXH 0 Temp 2 [T1 ndB] 6.37 dBm LVL 2.440750000 GHz -10 -20 -30 -40 -50 -60 -70 -80 Center 2.44 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 15:00:59 Figure 7.4.2-2: 6dB Bandwidth Plot – Mid Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 12.05 dBm Ref 20 dBm Att 40 dB SWT 2.5 ms 2.475220000 GHz 20 Offset 10 dB ndB [T1] 6.00 dB 1 BW 1.570000000 MHz Temp 1 [T1 ndB] A 10 T1 T2 6.34 dBm 1 PK 2.474180000 GHz MAXH 0 Temp 2 [T1 ndB] 5.88 dBm LVL 2.475750000 GHz -10 -20 -30 -40 -50 -60 -70 -80 Center 2.475 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 15:22:50 Figure 7.4.2-3: 6dB Bandwidth Plot – High Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 13

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 30 kHz Marker 1 [T1 ] VBW 100 kHz 9.45 dBm Ref 20 dBm Att 30 dB SWT 10 ms 2.404880000 GHz 20 Offset 10 dB OBW 2.400000000 MHz Temp 1 [T1 OBW] 1 A 10 -6.08 dBm 2.403770000 GHz 1 PK Temp 2 [T1 OBW] MAXH 0 -7.21 dBm T1 T2 2.406170000 GHz LVL -10 -20 -30 -40 -50 -60 -70 -80 Center 2.405 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 14:39:32 Figure 7.4.2-4: 99% Bandwidth Plot – Low Channel * RBW 30 kHz Marker 1 [T1 ] VBW 100 kHz 8.88 dBm Ref 20 dBm Att 30 dB SWT 10 ms 2.440060000 GHz 20 Offset 10 dB OBW 2.340000000 MHz Temp 1 [T1 OBW] 1 A 10 -8.16 dBm 2.438790000 GHz 1 PK Temp 2 [T1 OBW] MAXH 0 -8.09 dBm T1 T2 2.441130000 GHz LVL -10 -20 -30 -40 -50 -60 -70 -80 Center 2.44 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 15:02:28 Figure 7.4.2-5: 99% Bandwidth Plot – Mid Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 14

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 11.96 dBm Ref 20 dBm Att 30 dB SWT 2.5 ms 2.474690000 GHz 20 Offset 10 dB OBW 2.320000000 MHz 1 Temp 1 [T1 OBW] -3.71 dBm A 10 2.473800000 GHz 1 PK Temp 2 [T1 OBW] MAXH 0 T1 T2 -4.05 dBm 2.476120000 GHz LVL -10 -20 -30 -40 -50 -60 -70 -80 Center 2.475 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 15:23:35 Figure 7.4.2-6: 99% Bandwidth Plot – High Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 15

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.5 Peak Output Power Requirement - FCC Section 15.247(b)(3) IC: RSS-210 A8.4(4) 7.5.1 Test Methodology The Peak Output Power was measured in accordance with the FCC KDB Publication No. 558074 “Guidance on Measurements for Digital Transmission Systems (47 CFR 15.247)” Power Option 1. The RF output of the equipment under test was directly connected to the input of the Spectrum Analyzer. Data was collected with the EUT operating at maximum power. 7.5.2 Test Results Results are shown below in Table 7.5.2-1 and Figures 7.5.2-1 to 7.5.2-3. Table 7.5.2-1: Peak Output Power Frequency Output Power (MHz) (dBm) 2405 16.99 2440 15.83 2475 15.34 * RBW 3 MHz Marker 1 [T1 ] VBW 10 MHz 16.99 dBm Ref 20 dBm Att 40 dB SWT 2.5 ms 2.405020000 GHz 1 20 Offset 10 dB A 10 1 PK MAXH 0 LVL -10 -20 -30 -40 -50 -60 -70 -80 Center 2.405 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 14:32:16 Figure 7.5.2-1: Output power – Low Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 16

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 3 MHz Marker 1 [T1 ] VBW 10 MHz 15.83 dBm Ref 20 dBm Att 40 dB SWT 2.5 ms 2.439400000 GHz 20 Offset 10 dB 1 A 10 1 PK MAXH 0 LVL -10 -20 -30 -40 -50 -60 -70 -80 Center 2.44 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 15:00:16 Figure 7.5.2-2: Output power – Mid Channel * RBW 3 MHz Marker 1 [T1 ] VBW 10 MHz 15.34 dBm Ref 20 dBm Att 40 dB SWT 2.5 ms 2.475320000 GHz 20 Offset 10 dB 1 A 10 1 PK MAXH 0 LVL -10 -20 -30 -40 -50 -60 -70 -80 Center 2.475 GHz 500 kHz/ Span 5 MHz Date: 11.MAR.200 9 15:22:08 Figure 7.5.2-3: Output power – High Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 17

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.6 Band-Edge Compliance and Spurious Emissions - FCC Section 15.247(d) IC: RSS-210 2.6, A8.5 7.6.1 Band-Edge Compliance of RF Emissions 7.6.1.1 Test Methodology The EUT was investigated at the low and high channels of operation to determine band-edge compliance. All antenna types were evaluated. Because the upper band-edge coincides with a restricted band, band- edge compliance for the upper band-edge was determined using the radiated mark-delta method as outlined in FCC DA 00-705. The radiated field strength of the fundamental emission was first determined and then the mark-delta method was used to determine the field strength of the band-edge emissions. The lower band-edge compliance was determined using the marker-delta method in which the radio frequency power that is produced by the EUT is at least 20 dB below that within the band that contains the highest level of desired power. 7.6.1.2 Test Results Band-edge compliance is displayed in Tables 7.6.1.2-1 - 7.6.1.2-2 and Figure 7.6.1.2-1 – 7.6.1.2-3. Table 7.6.1.2-1: Upper Band-edge Marker Delta Method – 3S Level Antenna Correction Fundamental Field Band-edge Field Margin to Limit Delta- Frequency (dBuV) Polarity Factors Strength Strength (dBuV/m) Marker (MHz) (dBuV/m) (dBuV/m) 74 54 (dB) pk avg (H/V) (dB) pk avg pk avg pk avg Fundamental Frequency 2475 119.23 117.13 H -0.29 118.94 105.47 52.54 66.40 52.93 7.60 1.07 Table 7.6.1.2-2: Upper Band-edge Marker Delta Method – 4S Level Antenna Correction Fundamental Field Band-edge Field Margin to Limit Delta- Frequency (dBuV) Polarity Factors Strength Strength (dBuV/m) Marker (MHz) (dBuV/m) (dBuV/m) 74 54 (dB) pk avg (H/V) (dB) pk avg pk avg pk avg Fundamental Frequency 2475 119.98 117.52 H -0.29 119.69 105.86 52.54 67.15 53.32 6.85 0.68 * RBW 300 kHz Delta 1 [T1 ] VBW 1 MHz 52.54 dB Ref 120 1dBµV * Att 30 dB SWT 2.5 ms -8.464000000 MHz 120 Marker 1 [T1 ] 66.53 dBµV 2.483913000 GHz A 110 1 PK MAXH 100 90 80 70 1 60 50 40 30 20 Center 2.47975 GHz 1.15 MHz/ Span 11.5 MHz Date: 2.MAR.2009 14:06:16 Figure 7.6.1.2-1: Upper Band-edge (Radiated) – 3S ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 18

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 300 kHz Delta 1 [T1 ] VBW 1 MHz 52.54 dB Ref 120 1 dBµV * Att 30 dB SWT 2.5 ms -8.487000000 MHz 120 Marker 1 [T1 ] 66.77 dBµV 2.483959000 GHz A 110 1 PK MAXH 100 90 80 70 1 60 50 40 30 20 Center 2.47975 GHz 1.15 MHz/ Span 11.5 MHz Date: 2.MAR.2009 14:43:54 Figure 7.6.1.2-2: Upper Band-edge (Radiated) – 4S * RBW 300 kHz Delta 1 [T1 ] VBW 1 MHz 40.76 dB Ref 20 dBm Att 40 dB SWT 2.5 ms 5.536440000 MHz 1 20 Offset 10 dB Marker 1 [T1 ] -24.69 dBm 2.399949220 GHz A 10 1 PK MAXH 0 LVL -10 -20 1 -30 -40 -50 -60 -70 -80 Start 2.398 GHz 819 kHz/ Stop 2.40619 GHz Date: 11.MAR.200 9 14:56:30 Figure 7.6.1.2-3: Lower Band-edge (Conducted) 7.6.2 RF Conducted Spurious Emissions 7.6.2.1 Test Methodology The RF Conducted Spurious Emissions were measured in accordance with the FCC KDB Publication No. 558074 “Guidance on Measurements for Digital Transmission Systems (47 CFR 15.247)”. The RF output of the equipment under test was directly connected to the input of the Spectrum Analyzer. The EUT was investigated for conducted spurious emissions from 30MHz to 25GHz, 10 times the highest fundamental frequency. For each measurement, the spectrum analyzer’s RBW was set to 100 kHz and the VBW was set to 300 kHz. The peak detector and Max Hold function of the analyzer were utilized. 7.6.2.2 Test Results In a 100 kHz bandwidth, the radio frequency power that was produced by the EUT emissions is at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of desired power. RF Conducted Emissions are displayed in Figures 7.6.2.2-1 through 7.6.2.2-9. ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 19

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 12.40 dBm Ref 20 dBm * Att 30 dB SWT 250 ms 2.406140000 GHz 20 Offset 10 dB 1 B 10 1 PK MAXH 0 LVL D1 -7.6 dBm -10 -20 -30 -40 -50 -60 -70 -80 Start 30 MHz 247 MHz/ Stop 2.5 GHz Date: 11.MAR.2009 14:43:16 Figure 7.6.2.2-1: 30 MHz – 2.5 GHz – Low Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -40.97 dBm Ref 20 dBm * Att 30 dB SWT 1 s 4.800000000 GHz 20 Offset 10 dB B 10 1 PK MAXH 0 LVL D1 -7.6 dBm -10 -20 -30 1 -40 -50 -60 -70 -80 Start 2.5 GHz 1 GHz/ Stop 12.5 GHz Date: 11.MAR.2009 14:44:07 Figure 7.6.2.2-2: 2.5 GHz – 12.5 GHz – Low Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -32.87 dBm Ref 20 dBm * Att 30 dB SWT 1.25 s 21.700000000 GHz 20 Offset 10 dB B 10 1 PK MAXH 0 LVL D1 -7.6 dBm -10 -20 -30 1 -40 -50 -60 -70 -80 Start 12.5 GHz 1.25 GHz/ Stop 25 GHz Date: 11.MAR.2009 14:44:50 Figure 7.6.2.2-3: 12.5 GHz – 25 GHz – Low Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 20

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 12.34 dBm Ref 20 dBm * Att 30 dB SWT 250 ms 2.440720000 GHz 20 Offset 10 dB 1 B 10 1 PK MAXH 0 LVL D1 -8.74 dBm -10 -20 -30 -40 -50 -60 -70 -80 Center 1.265 GHz 247 MHz/ Span 2.47 GHz Date: 11.MAR.2009 15:04:07 Figure 7.6.2.2-4: 30 MHz – 2.5 GHz –Mid Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -42.35 dBm Ref 20 dBm * Att 30 dB SWT 1 s 9.600000000 GHz 20 Offset 10 dB B 10 1 PK MAXH 0 LVL D1 -8.74 dBm -10 -20 -30 -40 1 -50 -60 -70 -80 Start 2.5 GHz 1 GHz/ Stop 12.5 GHz Date: 11.MAR.2009 15:06:33 Figure 7.6.2.2-5: 2.5 GHz – 12.5 GHz – Mid Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -32.04 dBm Ref 20 dBm * Att 30 dB SWT 1.25 s 24.925000000 GHz 20 Offset 10 dB B 10 1 PK MAXH 0 LVL D1 -8.74 dBm -10 -20 -30 1 -40 -50 -60 -70 -80 Start 12.5 GHz 1.25 GHz/ Stop 25 GHz Date: 11.MAR.2009 15:07:28 Figure 7.6.2.2-6: 12.5 GHz – 25 GHz – Mid Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 21

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz 11.20 dBm Ref 20 dBm * Att 30 dB SWT 250 ms 2.475300000 GHz 20 Offset 10 dB 1 B 10 1 PK MAXH 0 LVL D1 -8.8 dBm -10 -20 -30 -40 -50 -60 -70 -80 Start 30 MHz 247 MHz/ Stop 2.5 GHz Date: 11.MAR.2009 15:26:40 Figure 7.6.2.2-7: 30 MHz – 2.5 GHz – High Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -42.44 dBm Ref 20 dBm * Att 30 dB SWT 1 s 9.560000000 GHz 20 Offset 10 dB B 10 1 PK MAXH 0 LVL D1 -8.8 dBm -10 -20 -30 -40 1 -50 -60 -70 -80 Start 2.5 GHz 1 GHz/ Stop 12.5 GHz Date: 11.MAR.2009 15:27:37 Figure 7.6.2.2-8: 2.5 GHz – 12.5 GHz –High Channel * RBW 100 kHz Marker 1 [T1 ] VBW 300 kHz -32.36 dBm Ref 20 dBm * Att 30 dB SWT 1.25 s 20.600000000 GHz 20 Offset 10 dB B 10 1 PK MAXH 0 LVL D1 -8.8 dBm -10 -20 -30 1 -40 -50 -60 -70 -80 Start 12.5 GHz 1.25 GHz/ Stop 25 GHz Date: 11.MAR.2009 15:28:22 Figure 7.6.2.2-9: 12.5 GHz – 25 GHz –High Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 22

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.6.3 Radiated Spurious Emissions (Restricted Bands) - FCC Section 15.205 IC: RSS-210 2.6 7.6.3.1 Test Methodology Radiated emissions tests were made over the frequency range of 30MHz to 25GHz, 10 times the highest fundamental frequency. The EUT was rotated through 360° and the receive antenna height was varied from 1m to 4m so that the maximum radiated emissions level would be detected. For frequencies below 1000MHz, quasi-peak measurements were made using a resolution bandwidth RBW of 120 kHz and a video bandwidth VBW of 300 kHz. For frequencies above 1000MHz, peak and average measurements made with RBW and VBW of 1 MHz and 3MHz respectively. The average emissions were further corrected by applying the duty cycle correction of the EUT to the average measurements for comparison to the average limit. Each emission found to be in a restricted band as defined by section 15.205, was compared to the radiated emission limits as defined in section 15.209. 7.6.3.2 Duty Cycle Correction For average radiated measurements, the measured level was reduced by a factor 11.37dB to account for the duty cycle of the EUT. The packet transmissions length is 27ms. The duty cycle correction factor is determined using the formula: 20log (0.27/100) = 11.37dB. A detailed analysis of the duty cycle timing is provided in the Theory of Operation. 7.6.3.3 Test Results Radiated spurious emissions found in the band of 30MHz to 25GHz for Meter Forms 3S and 4S are reported in Tables 7.6.3.3-1 and 7.6.3.3-2. Table 7.6.3.3-1: Radiated Spurious Emissions – 3S Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg Low Channel 4810 59.92 53.83 H 7.42 67.34 49.88 74.0 54.0 6.66 4.12 4810 62.83 56.90 V 7.52 70.35 53.05 74.0 54.0 3.65 0.95 12025 44.86 34.00 H 21.46 66.32 44.09 83.5 63.5 17.22 19.45 12025 43.87 33.44 V 21.47 65.34 43.54 83.5 63.5 18.20 20.00 Middle Channel 4880 56.19 49.89 H 7.69 63.88 46.21 74.0 54.0 10.12 7.79 4880 56.16 50.10 V 7.79 63.95 46.52 74.0 54.0 10.05 7.48 7320 50.50 41.11 H 11.97 62.47 41.71 74.0 54.0 11.53 12.29 7320 46.44 36.92 V 12.04 58.48 37.58 74.0 54.0 15.52 16.42 High Channel 4950 55.32 48.78 H 7.96 63.28 45.36 74.0 54.0 10.72 8.64 4950 54.08 47.15 V 8.06 62.14 43.83 74.0 54.0 11.86 10.17 7425 51.90 43.12 H 12.07 63.97 43.81 74.0 54.0 10.03 10.19 7425 46.92 38.24 V 12.15 59.07 39.02 74.0 54.0 14.93 14.98 * Note all other emissions were below the permissible limit ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 23

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 Table 7.6.3.3-2: Radiated Spurious Emissions – 4S Level Antenna Correction Corrected Level Limit Margin Frequency (dBuV) Polarity Factors (dBuV/m) (dBuV/m) (dB) (MHz) pk Qpk/Avg (H/V) (dB) pk Qpk/Avg pk Qpk/Avg pk Qpk/Avg Low Channel 4810 61.39 55.30 H 7.42 68.81 51.35 74.0 54.0 5.19 2.65 4810 61.27 55.23 V 7.52 68.79 51.38 74.0 54.0 5.21 2.62 12025 45.93 35.75 H 21.46 67.39 45.84 83.5 63.5 16.15 17.70 12025 45.88 36.44 V 21.47 67.35 46.54 83.5 63.5 16.19 17.00 Middle Channel 4880 58.68 52.66 H 7.69 66.37 48.98 74.0 54.0 7.63 5.02 4880 53.19 46.01 V 7.79 60.98 42.43 74.0 54.0 13.02 11.57 7320 48.92 40.40 H 11.97 60.89 41.00 74.0 54.0 13.11 13.00 7320 45.95 36.56 V 12.04 57.99 37.22 74.0 54.0 16.01 16.78 High Channel 4950 51.29 44.00 H 7.96 59.25 40.58 74.0 54.0 14.75 13.42 4950 54.51 47.76 V 8.06 62.57 44.44 74.0 54.0 11.43 9.56 7425 51.26 42.12 H 12.07 63.33 42.81 74.0 54.0 10.67 11.19 7425 45.67 36.31 V 12.15 57.82 37.09 74.0 54.0 16.18 16.91 * Note all other emissions were below the permissible limit 7.6.3.4 Sample Calculation: RC = RU + CFT Where: CFT = Total Correction Factor (AF+CA+AG)-DC (Average Measurements Only) RU = Uncorrected Reading RC = Corrected Level AF = Antenna Factor CA = Cable Attenuation AG = Amplifier Gain DC = Duty Cycle Correction Factor Example Calculation: Peak Corrected Level: 61.39+ 7.42 = 68.81dBuV/m Margin: 74dBuV/m – 68.81dBuV/m = 5.19dB Example Calculation: Average Corrected Level: 55.30+ 7.42 - 11.37 = 51.35dBuV Margin: 54dBuV – 51.35dBuV = 2.65dB ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 24

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 7.7 Peak Power Spectral Density- FCC Section 15.247(e) IC: RSS-210 A8.2(b) 7.7.1 Test Methodology The power spectral density was measured in accordance with the FCC KDB Publication No. 558074 “Guidance on Measurements for Digital Transmission Systems (47 CFR 15.247)”. The emission peaks within the pass band were located and zoomed in on. The spectrum analyzer RBW was set to 3 kHz and VBW 10 kHz. Span was adjusted to 500 kHz and the sweep time was calculated to be 168s (Span/3 kHz). 7.7.2 Test Results Results are shown below in table 7.7.2-1 and figures 7.7.2-1 – 7.7.2-3: Table 7.7.2-1: Peak Power Spectral Density Frequency PSD Level (MHz) (dBm) 2405 1.97 2440 1.36 2475 1.04 * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 1.97 dBm Ref 10 dBm Att 30 dB * SWT 170 s 2.405049000 GHz 10 Offset 10 dB 1 A 0 1 PK MAXH -10 LVL -20 -30 -40 -50 -60 -70 -80 -90 Center 2.40505 GHz 50 kHz/ Span 500 kHz Date: 11.MAR.200 9 14:53:49 Figure 7.7.2-1: Power Spectral Density Plot – Low Channel ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 25

Model: CVSO-B FCC ID: SK9AMI-5 IC: 864G-AMI5 * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 1.36 dBm Ref 10 dBm Att 30 dB * SWT 170 s 2.440048000 GHz 10 Offset 10 dB 1 A 0 1 PK MAXH -10 LVL -20 -30 -40 -50 -60 -70 -80 -90 Center 2.439858 GHz 50 kHz/ Span 500 kHz Date: 11.MAR.200 9 15:19:33 Figure 7.7.2-2: Power Spectral Density Plot – Mid Channel * RBW 3 kHz Marker 1 [T1 ] VBW 10 kHz 1.04 dBm Ref 10 dBm Att 30 dB * SWT 170 s 2.475048000 GHz 10 Offset 10 dB 1 A 0 1 PK MAXH -10 LVL -20 -30 -40 -50 -60 -70 -80 -90 Center 2.475054 GHz 50 kHz/ Span 500 kHz Date: 11.MAR.200 9 15:36:45 Figure 7.7.2-3: Power Spectral Density Plot – High Channel 8.0 CONCLUSION In the opinion of ACS, Inc. the CVSO-B, manufactured by Itron Electricity Metering, Inc. meets the requirements of FCC Part 15 subpart C and Industry Canada’s Radio Standards Specification RSS-210. END REPORT ACS Report: 09-0071-15C-DTS Advanced Compliance Solutions Page 26


Document Created: 2009-03-20 11:12:56
Document Modified: 2009-03-20 11:12:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC