user manual

FCC ID: RWE-4NPHLN

Users Manual

Download: PDF
FCCID_4364963



Components And Interfaces PIR AC connector Photoresistor Camera IR LED Anti—tamper MIC Calling Indicator Light button 0 The pictures are for reference only.

Components And Interfaces IR LED: When thelight is not enough, the IR LEDs will be enabled to Increase the brightness. Photoresistor: It is used to collect the brightness value, when the Illumination is lower than 2LUX, the IR LED 4 screw will be enabled. mounting hole MIC: Collect vaice Calling button: Used to activate the doorbell, notffied If there is a visitor, link to indoor chime. Wire holes P R: Automatically actlvate the doorbell when Bracket movement Is detected. Camera: Capture Images and video. Indicator Light: The red Indicator flashes slowly: The device is in configuration mode. The blue Indicatorflashes slowly: The device is working. The red and blue Indicator flashes alternately: Anti—tamper WIFI connection falled. screw hole The pictures are for reference only.

Components And Interfaces AC connector: Connect to external AC power AC16~24V. Antl—temper: Once the device is removed, the temper awitch will be activated. Memory card Reset: Long press 5s to reset. USB charging slot Power on/off: Power switch. Speaker Screw hole USB charging: Cherge the backup battery via the USB. Speaker: Talk to the visitor. Memory card slot: Insert a memory card up to 32G. Screw hole: Prevent equipment from being removed. The pictures are for reference only.

Installation instructions 1.1 Mounting bracket. Fix four screws on the wall, plank. 1.2 Install doorbell at the height about 1.3—1.6m Try to protect itself from rain and sun Clvk @ Fix bracket with screws @ Fix bracket well

Wire Doorbell Connect the doorbell to your existing low voltage wiring 2.1 Power supply of A: Low voltage AC 16—24V B: Battery 3.7—4.2V C: USB 5V (only for charging, not suggested to use it as power supply) 2.2 Insert disconnected 2—low voltage wires into the connector at the back. Cable will lock if it is inserted properly. Pull the cable to test. A Warning! Connect only Low Voltage AC 16—24V or DC5V power DO NOT CONNECT AC & DC BOTH AT THE SAME TIME 0 You can insert any color wire to any connector.

Install Doorbell 3.1 Slide the doorbell from Top to Bottom on the bracket. © Install the doorbell onto to mounting plate

Install Doorbell 4.1 Install the anti—tamper screw at the bottom of the mounting bracket. @ Screw the bottom, installation finished. 0 Do NOT over—tighten the locking screw.

Complete the installation 5.1 Locate existing (old) indoor bell/chime 5.2 Open the front cover by pulling the O y cover outward. You will see the existing chime terminal markings: "F" — Front Push Button Wire "T" — Transformer Wire "R" — Rear Push Button Wire A WARNING! Turn off power or circuit breaker before installing.

Finishing installation 5.3 Disconnect the wires from Trans (T) & Front (F) marked terminal 5.4 Join Trans (T) & Front (F) wire with twist —on wire connectors (Marette) 5.5 Remove wire from Rear (R) to disconnect the Rear doorbell. 5.6 Place the cover back on the old indoor bell/chime 0 If you have Front and Rear doorbells, the Rear doorbell must be disconnected. One Transformer can power only one doorbell. 9

Install indoor bell Indoor bell uses 3pcs*AAA batteries. When you press the WIFI doorbell button, indoor bell will ring. 0 Indoor bell is already synced with the WiFi doorbell unit.

Change Ringtones Install the indoor bell to the wall — 1 Find your favorite ringtone by pressing the "«« " or " »" button. — 2 Press and hold the Vol button until you hear a sound. Watch for blinking lights on the indoor bell. — 3 Quickly press the doorbell "call" button to pair. I” New ringtone will play if the pairing is successful. 0 Your existing (old) indoor bell will stop working. ©

Calling and Answer Calling (a) (b) (c)

Connect Doorbell to Network APP name is "ToSee", it supports both Android and IOS app, you can download it by scanning QR code on cover page or in the following ways: 1. Android: Search keyword "ToSee" on Google Play or Myapp to download the APP for Android devices. 2. I08: Search keyword "ToSee" on APP store to download the APP for IOS devices. ToSee 4. Available on the ANDROID APP ON 6 App Store Google Play

Connect Doorbell to Network 3. Tap "+" in the upper right of the app to add the device, select add device, and enter the next step. (3)

Connect Doorbell to Network 4. Enter the WIFI setting page of the mobile phone according to the instructions, find and connect the WIFI hotspot emitted by the Doorbell whose name starts with "ToSee", then return to the APP to continue to the next step. 15

Connect Doorbell to Network 5. In the configuration mode page, fill in the password of your WIFI and start configuring. 6. Set the administrator password for the device for device sharing and management. mesus use is wous use is Hanintanatoons

Connect Doorbell to Network 7. Please modify the name of the device after it is added successfully. wme s (7) Note: If you need to change the WIFI, please press and hold the reset button for 5 seconds, and the red light of the WiFi indicator will flash slowly, which means it is entering configuration mode.

Motion Detection Sensitivity Settings To improve the cameras response time to motion, you can adjust the motion sensitivity in the APP "Settings" section. The factory default setting for motion detection sensitivity is currently set at 10 seconds delay and can be adjusted as depicted below. 327 328 Settings < Motion Detection Sensitivity Motion Datection Sencitvty: Low ©) Uira Low Power Consumption () w & J DeviceIndicator Light o 9. Night Vision nfrared Light © (2) mage Fip Video Length Motion Detection Sensitdty Intercom Volume







E. Android M iOS


Document Created: 2019-07-12 11:23:17
Document Modified: 2019-07-12 11:23:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC