Antenna spec OP51508T-HP1

FCC ID: RTP-MRLBB1003

Parts List/Tune Up Info

Download: PDF

FCCID_1513224

6 5 4 3 2 1
REVISIONS
CHANGED APPROVED
REV. ECR# ZONE DESCRIPTION
BY/DATE BY/DATE

1 INITIAL PROTOTYPE K.S. 04-28-11 K.S. 04-28-11

CHANGED PART NUMBER TO BE HP SPECIFIC. ADDED FURTHER
2 PARAMETERS TO TABLE. K.S. 05-24-11 K.S. 05-24-11

D D

R Y
IN A
LI M Parameter
Model Number
Performance
OP51508T-HP1

R E HP Part Number
Frequency
TBD
5150-5875MHz

C
248.1
P Peak Gain
Omnidirectionality
Polarization
VSWR
8dBi
12dB Nominal
Linear, Vertical
2:1, Max
C

3X Impedance 50
91.0 Power 5W x 3
Port-to-Port Isolation 22dB
Cable Length 91cm (36") x 3
RF Connector Type N, Male
76.2
Cable Type RG58, Low Temp Plenum
Radome Material Polycarbonate, White
Weight TBD
Mounting Mast Mount
NOTE: MOUNTING HARDWARE Wind Surface Area (Curvature) 0.03 sq. m. (0.328 sq. ft.)
HAS NOT BEEN FINALIZED AT THIS Wind Survival 200 km/hr (125 mph)
B 209.4 TIME SO IT IS EXCLUDED FROM THIS B
DRAWING. IT WILL BE ADDED IN ON Wind Gust Survival 266 km/hr (165mph)
A FUTURE REVISION. Operational Temperature -30°C to +70°C
Storage Temperature -40°C to +85°C
45.0 Ingression Protection IP67

MATERIAL: THIRD ANGLE PROJECTION
52.0 N/A MANCHESTER, NH 03103
USA
FINISH: N/A
The component(s), including any plating, finishes, coatings, chemicals DO NOT SCALE DRAWING
and surfaces treatments, supplied in this document/drawing must conform TITLE:
A APPROVALS DATE
and comply with the latest issue of Laird Technologies Specification LT-GES-001,
which fully includes but is not limited to all contents of EU Directives 2002/95/EC
DRAWN BY K. SEARL 04-28-11
INTERPRET DIMENSIONING
AND TOLERANCING IN
ACCORDANCE WITH
OP51508T-HP1 A
(RoHS Directive), as well as includes requirements of the Joint Industry Guide ASME Y14.5M-2009
standard JIG-101, April 2005. The component(s) in this document/drawing may be
subject to a full compound analysis for proof of compliance. The latest issue of Laird
Technologies Specification LT-GES-001, (General Specification for the Environment)
PROJ. ENG.
TOLERANCES UNLESS
OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETERS
MOUNTING & OUTLINE
is readily available upon request from the supplier. APPL. MECH. SIZE REV
DWG. NO.
ANGLE: 30'
UNLESS OTHERWISE NOTED, THIS DOCUMENT CONTAINS LAIRD TECHNOLOGIES CONFIDENTIAL INFORMATION.
REPRODUCTION, USE, DISCLOSURE OR TRANSMITTAL OF ALL OR ANY PART OF THIS DOCUMENT IS
PROHIBITED EXCEPT TO THE EXTENT APPROVED IN WRITING BY AN AUTHORIZED REPRESENTATIVE
MFG.
0 PLACE DECIMAL:
1 PLACE DECIMAL:
2 PLACE DECIMAL:
0.5
0.25
0.13
A3 OP51508T-HP1MO 2
OF LAIRD TECHNOLOGIES. LAIRD TECHNOLOGIES RESERVES ALL RIGHTS UNDER PATENTS, TRADEMARKS, 1.6
COPY RIGHTS AND TRADE SECRETS. COPYRIGHT, LAIRD TECHNOLOGIES 2010, ALL RIGHTS RESERVED. SURFACE ROUGHNESS SCALE: 1:5 PREVIOUS# SHEET 1 OF 1

6 5 4 3 2 1

Document Created: 2011-07-29 11:51:47
Document Modified: 2011-07-29 11:51:47

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC