Test report-WCDMA

FCC ID: RQQHLT-E602TA

Test Report

Download: PDF

FCCID_4297995

Report No.: GTS20190515004-1-1-5 Page 2 of 30

TEST REPORT

May.21, 2019
Test Report No. : GTS20190515004-1-1-5 ______________________________________________________________________________________________

Date of issue

Equipment under Test : Smart Phone

Model /Type : E602

Listed Models : /

Applicant : HYUNDAI CORPORATION

Address : 25,Yulgok-ro 2-Gil, Jongno-gu, Seoul, South Korea

Manufacturer : Shenzhen Rainbow Time Technology Co.,Ltd

Address : 4/F.,H-3 Building,OCT Eastern lndustrial Park. NO.1 XiangShan
East Road.,Nan Shan District,Shenzhen,P.R.China.

Test Result: PASS

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.

Report No.: GTS20190515004-1-1-5 Page 3 of 30

Contents

1 TEST STANDARDS .................................................................. 4

2 SUMMARY ............................................................................. 5

2.1 General Remarks 5
2.2 Product Description 5
2.3 Equipment under Test 6
2.4 Short description of the Equipment under Test (EUT) 6
2.5 EUT configuration 6
2.6 Related Submittal(s) / Grant (s) 6
2.7 General Test Conditions/Configurations 7
2.8 Modifications 7

3 TEST ENVIRONMENT............................................................... 8

3.1 Address of the test laboratory 8
3.2 Test Facility 8
3.3 Environmental conditions 8
3.4 Test Description 9
3.5 Equipments Used during the Test 10

4 TEST CONDITIONS AND RESULTS ............................................ 11

4.1 Output Power 11
4.2 Radiated Spurious Emssion 15
4.3 Occupied Bandwidth and Emission Bandwith 18
4.4 Band Edge Compliance 20
4.5 Spurious Emssion on Antenna Port 22
4.6 Frequency Stability Test 27
4.7 Peak-to-Average Ratio (PAR) 29

5 TEST SETUP PHOTOS OF THE EUT .......................................... 30

6 EXTERNAL AND INTERNAL PHOTOS OF THE EUT ....................... 30

Report No.: GTS20190515004-1-1-5 Page 4 of 30

1 TEST STANDARDS
The tests were performed according to following standards:

FCC Part 2: FREQUENCY ALLOCA-TIONS AND RADIO TREATY MAT-TERS; GENERAL RULES AND
REG-ULATIONS

FCC Part 22 Subpart H: PRIVATE LAND MOBILE RADIO SERVICES.

FCC Part 24 Subpart E: PUBLIC MOBILE SERVICES

ANSI/TIA-603-E-2016: Land Mobile FM or PM Communications Equipment Measurement and Performance
Standards.

ANSI C63.26-2015: IEEE/ANSI Standard for Compliance Testing of Transmitters Used in Licensed Radio
Services

FCCKDB971168D01 Power Meas License Digital Systems

Report No.: GTS20190515004-1-1-5 Page 5 of 30

2 SUMMARY

2.1 General Remarks

Date of receipt of test sample : May.01, 2019

Testing commenced on : May.01, 2019

Testing concluded on : May.21, 2019

2.2 Product Description
The HYUNDAI CORPORATION’s Model: E602 or the “EUT” as referred to in this report; more general
information as follows, for more details, refer to the user’s manual of the EUT.

Name of EUT Smart Phone
Model Number E602
Modilation Type QPSK for UMTS,
Antenna Type Internal
UMTS Operation Frequency Band Device supported UMTS FDD Band II, FDD Band V
HSDPA Release Version Release 10
HSUPA Release Version Release 6
DC-HSUPA Release Version Not Supported
WCDMA Release Version R99
Extreme temp. Tolerance -30°C to +50°C
Extreme vol. Limits 3.40VDC to 4.20VDC (nominal: 3.85VDC)
Antenna gain: FDD Band V: -0.71dbi， FDD Band II：-0.86dbi

Report No.: GTS20190515004-1-1-5 Page 7 of 30

2.7 General Test Conditions/Configurations

2.7.1 Test Modes

NOTE: The test mode(s) are selected according to relevant radio technology specifications.

Test Mode Test Modes Description
UMTS/TM1 WCDMA system, QPSK modulation
UMTS/TM2 HSDPA system, QPSK modulation
UMTS/TM3 HSUPA system, QPSK modulation

Note:
1. This EUT owns two SIM cards, after we perform the pretest for these two SIM cards; we found the SIM 1
is the worst case, so its result is recorded in this report.
2. As WCDMA, HSDPA and HSUPA with the same emission designator, test result recorded in this report at
the worst case UMTS/TM1 only after exploratory scan.

2.7.2 Test Environment
Environment Parameter Selected Values During Tests
Relative Humidity Ambient
Temperature TN Ambient
VL 3.40V
Voltage VN 3.85V
VH 4.20V

NOTE: VL=lower extreme test voltage VN=nominal voltage
VH=upper extreme test voltage TN=normal temperature

2.8 Modifications
No modifications were implemented to meet testing criteria.

Report No.: GTS20190515004-1-1-5 Page 8 of 30

3 TEST ENVIRONMENT

3.1 Address of the test laboratory
Shenzhen Global Test Service Co.,Ltd.
No.7-101 and 8A-104, Building 7 and 8, DCC Cultural and Creative Garden, No.98, Pingxin North Road,
Shangmugu Community, Pinghu Street, Longgang District, Shenzhen, Guangdong

The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR 16-1-4:2010
SVSWR requirement for radiated emission above 1GHz.

3.2 Test Facility

The test facility is recognized, certified, or accredited by the following organizations:

FCC-Registration No.: 165725
Shenzhen Global Test Service Co.,Ltd EMC Laboratory has been registered and fully described in a report
filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained
in our files.

A2LA-Lab Cert. No.: 4758.01

Shenzhen Global Test Service Co.,Ltd. EMC Laboratory has been accredited by A2LA for
technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025:
2005 General Requirements for the Competence of Testing and Calibration Laboratories and any additional
program requirements in the identified field of testing.

CNAS-Lab Code: L8169
Shenzhen Global Test Service Co.,Ltd. has been assessed and proved to be in compliance with CNAS-
CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC 17025: 2005
General Requirements) for the Competence of Testing and Calibration Laboratories. Date of Registration:
Dec. 11, 2015. Valid time is until Dec. 10, 2024.

3.3 Environmental conditions

During the measurement the environmental conditions were within the listed ranges:

Temperature: 15-35 °C

Humidity: 30-60 %

Atmospheric pressure: 950-1050mbar
(1) expressed at approximately the 95% confidence level using a coverage factor of k=1.96.

Report No.: GTS20190515004-1-1-5 Page 9 of 30

3.4 Test Description

3.4.1 Cellular Band (824-849MHz paired with 869-894MHz)
Test Item FCC Rule Requirements Verdict
No.
Effective(Isotropic) §2.1046,
FCC: ERP ≤ 7W. Pass
Radiated Output Power §22.913
Modulation
§2.1047 Digital modulation N/A
Characteristics
OBW: No limit.
Bandwidth §2.1049 Pass
EBW: No limit.
≤-13dBm/1%*EBW, in 1MHz bands immediately outside
Band Edges §2.1051,
and adjacent to Pass
Compliance §22.917
The frequency block.
FCC: ≤ -13dBm/100kHz,
Spurious Emission at §2.1051,
from 9kHz to 10th harmonics but outside authorized Pass
Antenna Terminals §22.917
operating frequency ranges.
Field Strength of
§2.1053,
Spurious FCC: ≤ -13dBm/100kHz. Pass
§22.917
Radiation
§2.1055,
Frequency Stability ≤ ±2.5ppm. Pass
§22.355
NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.

3.4.2 PCS Band (1850-1915MHz paired with 1930-1995MHz)
Test Item FCC Rule Requirements Verdict
No.
Effective(Isotropic) §2.1046,
EIRP ≤ 2W Pass
Radiated Output Power §24.232
§2.1046,
Peak-Average Ratio FCC:Limit≤13dB Pass
§24.232
Modulation
§2.1047 Digital modulation N/A
Characteristics
OBW: No limit.
Bandwidth §2.1049 Pass
EBW: No limit.
≤ -13dBm/1%*EBW,
Band Edges §2.1051,
In 1MHz bands immediately outside and adjacent to Pass
Compliance §24.238
The frequency block.
≤-13dBm/1MHz,
Spurious Emission at §2.1051,
from 9kHz to10th harmonics but outside authorized Pass
Antenna Terminals §24.238
Operating frequency ranges.
Field Strength of
§2.1053,
Spurious ≤ -13dBm/1MHz. Pass
§24.238
Radiation
§2.1055, FCC: within authorized frequency
Frequency Stability Pass
§24.235 block.
NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.

Remark: 1. The measurement uncertainty is not included in the test result.

Report No.: GTS20190515004-1-1-5 Page 12 of 30

Burst Average Conducted power
Test Mode Test Channel (dBm)
UMTS Band V UMTS Band II
LCH 22.61 22.73
UMTS/TM1 MCH 22.93 23.16
HCH 22.94 22.80
LCH_SubTest-1 22.18 22.35
LCH_SubTest-2 22.16 22.46
LCH_SubTest-3 22.27 22.39
LCH_SubTest-4 21.22 21.47
MCH_SubTest-1 22.53 22.51
MCH_SubTest-2 21.61 21.86
UMTS/TM2
MCH_SubTest-3 21.55 21.75
MCH_SubTest-4 21.70 22.03
HCH_SubTest-1 22.53 22.09
HCH_SubTest-2 22.45 22.30
HCH_SubTest-3 22.63 22.53
HCH_SubTest-4 21.51 21.31
LCH_SubTest-1 20.75 20.29
LCH_SubTest-2 20.41 20.38
LCH_SubTest-3 21.33 21.17
LCH_SubTest-4 20.48 20.19
LCH_SubTest-5 19.98 20.32
MCH_SubTest-1 21.25 21.63
MCH_SubTest-2 20.28 20.61
UMTS/TM3 MCH_SubTest-3 21.33 21.68
MCH_SubTest-4 20.17 20.53
MCH_SubTest-5 21.33 21.71
HCH_SubTest-1 20.21 20.35
HCH_SubTest-2 20.42 20.23
HCH_SubTest-3 21.71 21.22
HCH_SubTest-4 20.32 20.35
HCH_SubTest-5 20.26 20.27

Report No.: GTS20190515004-1-1-5 Page 14 of 30

reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be
performed by rotating the test item and adjusting the receiving antenna polarization.
5. A amplifier should be connected to the Signal Source output port. And the cable should be connect
between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain
(Ga) and the Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea- PAg - Pcl + Ga
We used SMF100A micowave signal generator which signal level can up to 33dBm,so we not used power
Amplifier for substituation test; The measurement results are amend as described below:
Power(EIRP)=PMea- Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi.

TEST LIMIT

According to 22.913(a), 24.232(c) the ERP(EIRP) should be not exceeding following table limits:

Burst Average ERP
UMTS Band V 38.45dBm (7W)

TEST RESULTS

Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Note: We test the H direction and V direction, V direction is worse.

UMTS/TM1/UMTS Band II
Ga Burst
Frequency PMea Pcl Antenna PAg Average Limit Margin
Polarization
(MHz) (dBm) (dB) Gain (dB) EIRP (dBm) (dB)
(dB) (dBm)
1852.4 -19.31 3.41 10.24 33.60 21.12 33.01 11.89 V
1880.0 -18.24 3.49 10.24 33.60 22.11 33.01 10.90 V
1907.6 -19.00 3.55 10.23 33.60 21.28 33.01 11.73 V

UMTS/TM1/UMTS Band V
Ga Burst
Frequency PMea Pcl Antenna Correction PAg Average Limit Margin
Polarization
(MHz) (dBm) (dB) Gain (dB) (dB) ERP (dBm) (dB)
(dB) (dBm)
826.40 -18.84 2.42 8.45 2.15 36.82 21.86 38.45 16.59 V
836.60 -18.25 2.46 8.45 2.15 36.82 22.41 38.45 16.04 V
846.60 -18.83 2.53 8.36 2.15 36.82 21.67 38.45 16.78 V

Report No.: GTS20190515004-1-1-5 Page 16 of 30

3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set
Test Receiver or Spectrum RBW=1MHz,VBW=3MHz, And the maximum value of the receiver should be
recorded as (Pr).
4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the
frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the
frequency band of interest is connected to the substitution antenna with a cable that has been constructed
to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the
substitution antenna, and adjust the level of the signal generator output until the value of the receiver
reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be
performed by rotating the test item and adjusting the receiving antenna polarization.
5. A amplifier should be connected to the Signal Source output port. And the cable should be connect
between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain
(Ga) and the Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea- PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi.
8. In order to make sure test results more clearly,we set frequency range and sweep time for difference
frequency range as follows table:

Working Subrange Sweep time
RBW VBW
Frequency (GHz) (s)
0.00009~0.15 1KHz 3KHz 30
0.00015~0.03 10KHz 30KHz 10
0.03~1 100KHz 300KHz 10
UMTS/TM1/
1~2 1 MHz 3 MHz 2
WCDMA Band V
2~5 1 MHz 3 MHz 3
5~8 1 MHz 3 MHz 3
8~10 1 MHz 3 MHz 3
0.00009~0.15 1KHz 3KHz 30
0.00015~0.03 10KHz 30KHz 10
0.03~1 100KHz 300KHz 10
1~2 1 MHz 3 MHz 2
UMTS/TM1/ 2~5 1 MHz 3 MHz 3
WCDMA Band II 5~8 1 MHz 3 MHz 3
8~11 1 MHz 3 MHz 3
11~14 1 MHz 3 MHz 3
14~18 1 MHz 3 MHz 3
18~20 1 MHz 3 MHz 2

TEST LIMITS

According to 24.238, 22.917 specify that the power of any emission outside of the authorized operating
frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P)
dB.
The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log
(P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum
attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0
dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the
specification from relative to absolute terms is carried out.

Frequency Channel Frequency Range Verdict
Low 9KHz-10GHz PASS
UMTS/TM1/ WCDMA
Middle 9KHz -10GHz PASS
Band V
High 9KHz -10GHz PASS
Low 9KHz -20GHz PASS
UMTS/TM1/ WCDMA
Middle 9KHz -20GHz PASS
Band II
High 9KHz -20GHz PASS

Report No.: GTS20190515004-1-1-5 Page 17 of 30

TEST RESULTS

Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
5. Margin = Limit – Emission Level
6. We test both H direction and V direction, recorded worst case direction.

UMTS/TM1/ WCDMA Band II _ Low Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3704.8 -42.30 4.39 3.00 12.34 -34.35 -13.00 21.35 H
5557.2 -44.90 5.31 3.00 13.52 -36.69 -13.00 23.69 H
3704.8 -40.16 4.39 3.00 12.34 -32.21 -13.00 19.21 V
5557.2 -45.46 5.31 3.00 13.52 -37.25 -13.00 24.25 V

UMTS/TM1/ WCDMA Band II _ Middle Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3760.0 -41.29 4.41 3.00 12.34 -33.36 -13.00 20.36 H
5640.0 -46.57 5.38 3.00 13.58 -38.37 -13.00 25.37 H
3760.0 -39.75 4.41 3.00 12.34 -31.82 -13.00 18.82 V
5640.0 -46.49 5.38 3.00 13.58 -38.29 -13.00 25.29 V

UMTS/TM1/ WCDMA Band II _ High Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
3815.2 -40.33 4.45 3.00 12.45 -32.33 -13.00 19.33 H
5722.8 -47.30 5.47 3.00 13.66 -39.11 -13.00 26.11 H
3815.2 -39.23 4.45 3.00 12.45 -31.23 -13.00 18.23 V
5722.8 -46.16 5.48 3.00 13.66 -37.98 -13.00 24.98 V

UMTS/TM1/ WCDMA Band V _ Low Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1652.8 -38.62 3.00 3.00 9.58 -32.04 -13.00 19.04 H
2479.2 -43.74 3.03 3.00 10.72 -36.05 -13.00 23.05 H
1652.8 -36.22 3.00 3.00 9.68 -29.54 -13.00 16.54 V
2479.2 -39.8 3.03 3.00 10.72 -32.11 -13.00 19.11 V

UMTS/TM1/ WCDMA Band V _ Middle Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1672.8 -37.78 3.00 3.00 9.58 -31.20 -13.00 18.20 H
2509.2 -42.67 3.03 3.00 10.72 -34.98 -13.00 21.98 H
1672.8 -35.75 3.00 3.00 9.68 -29.07 -13.00 16.07 V
2509.2 -40.34 3.03 3.00 10.72 -32.65 -13.00 19.65 V

UMTS/TM1/ WCDMA Band V _ High Channel
Ga Peak
Frequency PMea Pcl Limit Margin
Diatance Antenna EIRP Polarization
(MHz) (dBm) (dB) (dBm) (dB)
Gain(dB) (dBm)
1693.2 -37.43 3.00 3.00 9.58 -30.85 -13.00 17.85 H
2539.8 -41.46 3.03 3.00 10.72 -33.77 -13.00 20.77 H
1693.2 -36.84 3.00 3.00 9.68 -30.16 -13.00 17.16 V
2539.8 -39.30 3.03 3.00 10.72 -31.61 -13.00 18.61 V

Report No.: GTS20190515004-1-1-5 Page 28 of 30

frequency block. As this transceiver is considered "Hand carried, battery powered equipment" Section
2.1055(d)(2) applies. This requires that the lower voltage for frequency stability testing be specified by the
manufacturer. This transceiver is specified to operate with an input voltage of between 3.40VDC and 4.20VDC,
with a nominal voltage of 3.80DC. Operation above or below these voltage limits is prohibited by transceiver
software in order to prevent improper operation as well as to protect components from overstress. These
voltages represent a tolerance of -10 % and +12.5 %. For the purposes of measuring frequency stability these
voltage limits are to be used.

For equipment powered by primary supply voltage
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. For this EUT section 2.1055(d)(1) applies. This requires varying primary supply voltage from
85 to 115 percent of the nominal value for other than hand carried battery equipment.

TEST RESULTS

UMTS/TM1/WCDMA Band II
Channel 9400 / 1880.0 MHz
Temperature Frequency Frequency Limit
DC Power Verdict
(℃) error(Hz) error(ppm) (ppm)
3.40 20 38 0.020 2.50 PASS
3.85 20 28 0.015 2.50 PASS
4.20 20 42 0.022 2.50 PASS
3.85 -30 39 0.021 2.50 PASS
3.85 -20 47 0.025 2.50 PASS
3.85 -10 32 0.017 2.50 PASS
3.85 0 28 0.015 2.50 PASS
3.85 10 31 0.016 2.50 PASS
3.85 20 39 0.021 2.50 PASS
3.85 30 28 0.015 2.50 PASS
3.85 40 27 0.014 2.50 PASS
3.85 50 25 0.013 2.50 PASS

UMTS/TM1/WCDMA Band V
Channel 4183 / 836.6 MHz
Temperature Frequency Frequency Limit
DC Power Verdict
(℃) error(Hz) error(ppm) (ppm)
3.40 20 29 0.035 2.50 PASS
3.85 20 31 0.037 2.50 PASS
4.20 20 28 0.033 2.50 PASS
3.85 -30 32 0.038 2.50 PASS
3.85 -20 42 0.050 2.50 PASS
3.85 -10 37 0.044 2.50 PASS
3.85 0 29 0.035 2.50 PASS
3.85 10 31 0.037 2.50 PASS
3.85 20 35 0.042 2.50 PASS
3.85 30 31 0.037 2.50 PASS
3.85 40 36 0.043 2.50 PASS
3.85 50 35 0.042 2.50 PASS

Document Created: 2019-05-29 13:51:03
Document Modified: 2019-05-29 13:51:03

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC