RF Test Report

FCC ID: QYLPN7462U

Test Report

Download: PDF
FCCID_4289563

( nt' Report Number: 1904FR12 \-’ Rev.00 RF Test Report Applicant : Getac Technology Corporation Product Type : NFC Module Trade Name : Getac Model Number : UX10 PN7462 NFC Module Test Specification : FCC 47 CFR PART 15 SUBPART C ANSI C63.10:2013 Receive Date : Mar. 08, 2019 Test Period : Mar. 26 ~ Mar. 29, 2019 Issue Date : Apr. 03, 2019 Issue by A Test Lab Techno Corp. No. 140—1, Changan Street, Bade District, ally» & Taoyuan City 33465, Taiwan (R.O.C.) ifa%é/i{i @ Tel : +886—3—2710188 / Fax : +886—3—2710190 mrag | 4 Taiwan Accreditation Foundation accreditation number: 1330 Test Firm MRA designation number: TWOO010 Note: This report shall—not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno—Corp. personnel only, and shall be noted in the revision section of the—document: The client should not use it to claim product endorsement by TAF; or any government agencies.—The test—results in the report only apply to the tested sample. 1 of 33

Report Number: 1904FR12 Rev.00 Revision History Rev. Issue Date Revisions Revised By 00 Apr. 03, 2019 Initial Issue Janet Chao 2 of 33

( ntl Report Number: 1904FR12 Rev.00 Verification of Compliance Issued Date: Apr. 03, 2019 Applicant : Getac Technology Corporation Product Type : NFC Module Trade Name : Getac Model Number : UX10 PN7462 NFC Module FCC ID : QYLPN7462U EUT Rated Voltage : DC SV Test Voltage : 120 Vac / 60 Hz Applicable Standard _: FCC 47 CFR PART 15 SUBPART C ANSI C63.10:2013 Test Result : Complied Performing Lab. : _A Test Lab Techno Corp. \\\¥ * No. 140—1, Changan Street, Bade District, m Taoyuan City 33465, Taiwan (R.O0.C.) 3,/4T?\ Tel : +886—3—2710188 / Fax : +886—3—2710190 Taiwan Accreditation Foundation accreditation number: 1330 http:/Avww.atl—lab.com.tw/e—index.htm A Test Lab Techno Corp. tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by A Test Lab Techno Corp. based on interpretations and/or observations of test results. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Approved By : zly ;/ LA Reviewed By : Ea/(’c Ou i/ (Manager) (Fly Lu) (Testing Engineer) (Eric Ou Yang) 3 of 33

Report Number: 1904FR12 Rev.00 TABLE OF CONTENTS 1 General Information ............................................................................................................. 5 1.1. Summary of Test Result ................................................................................................. 5 1.2. Measurement Uncertainty .............................................................................................. 6 2 EUT Description ................................................................................................................... 7 3 Test Methodology................................................................................................................. 8 3.1. Mode of Operation ......................................................................................................... 8 3.2. EUT Test Step................................................................................................................ 8 3.3. Configuration of Test System Details ............................................................................. 9 3.4. Test Instruments .......................................................................................................... 10 3.5. Test Site Environment .................................................................................................. 11 4 Measurement Procedure.................................................................................................... 12 4.1. AC Power Line Conducted Emission Measurement ..................................................... 12 4.2. Radiated Emission Measurement ................................................................................ 14 4.3. Frequency Stability Measurement ................................................................................ 18 4.4. 20 dB Bandwidth Measurement ................................................................................... 20 4.5. Antenna Requirement .................................................................................................. 21 5 Test Results ........................................................................................................................ 22 Annex A. Conducted Emission ............................................................................................. 22 Annex B. Conducted Test Results ........................................................................................ 24 Annex C. Radiated Emission Measurement ......................................................................... 26 4 of 33

Report Number: 1904FR12 Rev.00 1 General Information 1.1. Summary of Test Result Standard Item Results Remark FCC 15.203 Antenna Requirement Meet Require --- 15.207(a) Conducted Emissions Voltage PASS --- 15.225 (a), (b), (c), (d) Radiated Emission Limits PASS --- 15.209 15.225(e) Frequency Stability PASS --- 15.215(c) 20 dB Bandwidth ----- --- CFR 47 Part 15.225 / ANSI C63.10:2013 The test results of this report relate only to the tested sample(s) identified in this report. Standard Description CFR47, Part 15, Subpart C Intentional Radiators American National Standard of Procedures for Compliance Testing of ANSI C63. 10: 2013 Unlicensed Wireless Devices 5 of 33

Report Number: 1904FR12 Rev.00 1.2. Measurement Uncertainty Test Item Frequency Range Uncertainty 9 kHz ~ 150 kHz 2.7 Conducted Emission 150 kHz ~ 30 MHz 2.7 9 kHz ~ 30 MHz 1.7 30 MHz ~ 1000 MHz 5.7 Radiated Emission 1000 MHz ~ 18000 MHz 5.5 18000 MHz ~ 26500 MHz 4.8 26500 MHz ~ 40000 MHz 4.8 RF Bandwidth 4.96 % Frequency Stability + 2.212 x 10-7 % / - 2.170 x 10-7 6 of 33

( ntl Report Number: 19047R 12 \_4 Rev.00 2 EUT Description Getee Technology Corporation Applicant 5F., Building A, No.208, Seo1, Nengang Rd., Nengang Dist, Taipei City, 11568, Tawan Manutsct Infotrink anulctirer DeLing Vilege, De.ingShan Town, DangGuen oiGuangDong Province China Product NFC Module Trade Name Getze Model Number UX10 PN7482 NFC Module Fee in oveNresau Frequency Renge 13.58 Mz Modulation Type por Number of Channels 1 Channel Antenna Type Loop Antenna Operate Temp. Renge 10— «s0 °c 7 of 33

( ntl Report Number: 19047R 12 \_4 Rev.00 3 Test Methodology 3.1. Mode of Operation The following test mode(s) were scanned during the preliminary test Test Mode Mode 1: TransmitMode Mode 2: Continuous TX Mode After verification, alltests were carnied out with the worst case test mades ATL has verifed the construction and function in typical operation. Allthe test mades were carned out with the EUT in normal operation 3.2. EUT Test Step 1. Setup the EUT shown on ‘Confiquration of Test System Details." 2. Turon the power of all equipment 3. The EUT will star to operate function Measurement Sotwere No. Description version 1| Conducted Emission 1143 2| Reciated Emission n144 8 of 33

Report Number: 1904FR12 Rev.00 3.3. Configuration of Test System Details Conducted Emission AC Input (4) AC Adapter (7)Tablet (5) Monitor (6) HDMI Cable EUT (3)SD Card (2) Earphone & Microphone (1) Mouse Radiated Emission (4) AC Adapter (7)Tablet EUT (3)SD Card 9 of 33

Report Number: 19047R 12 Rev.00 Devices Description Product Manufacturer.|. Model Number Seriel Number Power Cord (1) Mouse Logitech muacess — — @| same: |_me — — — (@) SD Card Transcend — — — (4) ACAdapter rep reposs—reena — — (6) Monitor neu prsisob |CN—0DsceY—r4201—523—0HUL — (6) HOM Cable Avier iasohs — — @) Tablet Getzo uxi0 — — 3.4. Test Instruments Conducted Emission Test Period: Mer, 27, 2019 & m #om 0& #o k Aki e in dt Test Receiver res esol 10037 osnvzore 1 year usn res evzie 101040 camore 1 year RF Cable Woken umuumasme Te—oros osnmore 1 year 10 of 33

@l Report Number: 19047R 12 Rev.00 Conducted / Radiated Emissions Test Period: Mar, 28 — Mer, 23, 2019 & m on El a #o k Aiceskein detei Spectrum (10 He—44Analyzer GHz) Keysight NegroA mMys222r312 ovnarzore 1 year (100Preit Amplifer a one) Agient s«470 ressatiiie ovnarzore 1 year Broadband Antenna Schwarzbeck vurserss «18 1ongro1e 1 year Loop Antenna ElectroMetries EMCH—LPAG00 ar caneraore 1 year RF Cable EMCI EMC‘M&N'N'GUU Teor—1 carar01 1 year Microwave Cable EMCI EMC‘F:&?SA'SM' w81 1002018 1 year Microwave Cable emcl EMC‘F;&W'KM' 151001 sarorzore 1 year 3.5. Test Site Environment tems Required ((EC 60068—1) Actual Temperature (°C) 1535 20 Humidity (GGRH) 25—75 so Barometric pressure (mbar) se0—1080 seo 11 of 33

Report Number: 1904FR12 Rev.00 4 Measurement Procedure 4.1. AC Power Line Conducted Emission Measurement  Limit Frequency (MHz) Quasi-peak Average 0.15 - 0.5 66 to 56 56 to 46 0.50 - 5.0 56 46 5.0 - 30.0 60 50  Test Setup 12 of 33

Report Number: 1904FR12 Rev.00  Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 50 Ω // 50 uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 50 Ω // 50 uH coupling impedance with 50 ohm termination. Tabletop device shall be placed on a non-conducting platform, of nominal size 1 m by 1.5 m, raised 80 cm above the reference ground plane. The wall of screened room shall be located 40 cm to the rear of the EUT. Other surfaces of tabletop or floor standing EUT shall be at least 80 cm from any other ground conducting surface including one or more LISNs. For floor-standing device shall be placed under the EUT with a 12 mm insulating material. Conducted emissions were investigated over the frequency range from 0.15 MHz to 30 MHz using a resolution bandwidth of 9 kHz. The equipment under test (EUT) shall be meet the limits in section 4.1, as applicable, including the average limit and the quasi-peak limit when using respectively, an average detector and quasi-peak detector measured in accordance with the methods described of related standard. When all of peak value were complied with quasi-peak and average limit from 150 kHz to 30 MHz then quasi-peak and average measurement was unnecessary. The AMN shall be placed 0.8 m from the boundary of the unit under test and bonded to a ground reference plane for AMNs mounted on top of the ground reference plane. This distance is between the closest points of the AMN and the EUT. All other units of the EUT and associated equipment shall be at least 0.8 m from the AMN. If the mains power cable is longer than 1 m then the cable shall be folded back and forth at the centre of the lead to form a bundle no longer than 0.4 m. All of interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 cm to 40 cm long. All of EUT and AE shall be separate place more than 0.1 m. All 50 Ω ports of the LISN shall be resistively terminated into 50 Ω loads when not connected to the measuring instrument. If the reading of the measuring receiver shows fluctuations close to the limit, the reading shall be observed for at least 15 s at each measurement frequency; the higher reading shall be recorded with the exception of any brief isolated high reading which shall be ignored. 13 of 33

Report Number: 1904FR12 Rev.00 4.2. Radiated Emission Measurement  Limit According to §15.225, (a) The field strength of any emissions within the band 13.553 – 13.567 MHz shall not exceed 15,848 microvolt / meter at 30 meters. (b) Within the bands 13.410 – 13.553 MHz and 13.567 -13.710 MHz, the field strength of any emissions shall not exceed 334 microvolt / meter at 30 meters. (c) Within the bands 13.110 – 13.410 MHz and 13.710 – 14.010 MHz the field strength of any emissions shall not exceed 106 microvolt / meter at 30 meters. (d) The field strength of any emissions appearing outside of the 13.110 – 14.010 MHz and shall not exceed the general radiated emission limits in §15.209. According to §15.225(a), except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (μV/m at meter) (meter) 0.009 – 0.490 2400 / F (kHz) 300 0.490 – 1.705 24000 / F (kHz) 30 1.705 – 30.0 30 30 30 - 88 100** 3 88-216 150** 3 216-960 200** 3 Above 960 500 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 14 of 33

Report Number: 1904FR12 Rev.00  Setup 9 kHz ~ 30 MHz 30 MHz ~ 1 GHz Antenna tower 3m Bilog antenna EUT 4m Spectrum / Receiver Turntable 1m 0.8m Pre-amp Reference ground plane 15 of 33

Report Number: 1904FR12 Rev.00  Test Procedure Final radiation measurements were made on a three-meter Semi Anechoic Chamber. The EUT system was placed on a nonconductive turntable which is 0.8 meters height, top surface 1.0 x 1.5 meter. The spectrum was examined from 3 Hz to 44 GHz in order to cover the whole spectrum below 10th harmonic which could generate from the EUT. During the test, EUT was set to transmit continuously. For measurements below 1 GHz the resolution bandwidth is set to 100 kHz for peak detection measurements or 120 kHz for quasi-peak detection measurements. Peak detection is used unless otherwise noted as quasi-peak. For measurements above 1 GHz the resolution bandwidth is set to 1 MHz, and then the video bandwidth is set to 3 MHz for peak measurements and 10 Hz for average measurements. A nonconductive material surrounded the EUT to supporting the EUT for standing on tree orthogonal planes. At each condition, the EUT was rotated 360 degrees, and the antenna was raised and lowered from one to four meters to find the maximum emission levels. Measurements were taken using both horizontal and vertical antenna polarization. Broadband/Horn Antenna were used in frequency 30 MHz to 18 GHz at a distance of 3 meter. Loop/Horn Antenna was used in frequency 9 kHz to 30 MHz and 18 to 26.5 GHz at a distance of 1 meter. All test results were extrapolated to equivalent signal at 3 meters utilizing an inverse linear distance extrapolation Factor (20 dB/decade). For testing above 1 GHz, the emission level of the EUT in peak mode was 20 dB lower than average limit (that means the emission level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. Appropriate preamplifiers were used for improving sensitivity and precautions were taken to avoid overloading or desensitizing the spectrum analyzer. No post – detector video filters were used in the test. The spectrum analyzer’s 6 dB bandwidth was set to 1 MHz, and the analyzer was operated in the peak detection mode, for frequencies both below and up 1 GHz. The average levels were obtained by subtracting the duty cycle correction factor from the peak readings. The following procedures were used to convert the emission levels measured in decibels referenced to 1 microvolt (dBuV) into field intensity in microvolt pre-meter (uV/m). The actual field intensity in decibels referenced to 1 microvolt in to field intensity in microvolt per-meter (dBuV/m). 16 of 33

Report Number: 1904FR12 Rev.00 The actual field is intensity in referenced to 1 microvolt per meter (dBuV/m) is determined by algebraically adding the measured reading in dBuV, the antenna factor (dB), and cable loss (dB) and Subtracting the gain of preamplifier (dB) is auto calculate in spectrum analyzer. (1) Amplitude (dBuV/m) = FI (dBuV) +AF (dBuV) +CL (dBuV)-Gain (dB) FI= Reading of the field intensity. AF= Antenna factor. CL= Cable loss. P.S Amplitude is auto calculate in spectrum analyzer. (2) Actual Amplitude (dBuV/m) = Amplitude (dBuV)-Dis(dB) The FCC specified emission limits were calculated according the EUT operating frequency and by following linear interpolation equations: (a) For fundamental frequency : Transmitter Output < +30 dBm (b) For spurious frequency : Spurious emission limits = fundamental emission limit /10 Data of measurement within this frequency range without mark in the table above means the reading of emissions are attenuated more than 20 dB below the permissible limits or the field strength is too small to be measured. 17 of 33

Report Number: 1904FR12 Rev.00 4.3. Frequency Stability Measurement  Limit According to §15.207(e), the frequency tolerance of the carrier signal shall be maintained within +/- 0.01 % of the operating frequency over a temperature variation of –20 degrees to +50 degrees C at normal supply voltage, and for a variation in the primary supply voltage from 85 % to 115 % of the rated supply voltage at a temperature of 20 degrees C. For battery operated equipment, the equipment tests shall be performed using a new battery.  Test Setup 18 of 33

Report Number: 1904FR12 Rev.00  Test Procedure 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the environment into appropriate environment. 4. Set the spectrum analyzer as RBW = 1 kHz, VBW = RBW, Span = 200 kHz, Sweep = auto. 5. Mark the peak frequency and measure the frequency tolerance using frequency counter function. 6. Repeat until all the results are investigated. 19 of 33

Report Number: 1904FR12 Rev.00 4.4. 20 dB Bandwidth Measurement  Limit N/A  Test Setup Spectrum Analyzer RF Cable EUT  Test Procedure Connect RF output port to the input of the spectrum analyzer. Connect the DUT to appropriate power supply. Turn RFID function of DUT on. Analyzer used the following settings: 1. Span = 60 kHz 2. RBW ≥ 1 % of the 20 dB span 3. VBW ≥ RBW 4. Sweep = auto 5. Detector function = peak 6. Trace = max hold The trace was allowed to stabilize. The EUT was transmitting at its maximum data rate. The marker-to-peak function was used to set the marker to the peak of the emission. The marker-delta function was used to measure 20 dB down one side of the emission. The marker-delta function and marker was moved to the other side of the emission until it was even with the reference marker. The marker-delta reading at this point was the 20 dB bandwidth of the emission. 20 of 33

Report Number: 1904FR12 Rev.00 4.5. Antenna Requirement  Require An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited.  Antenna Connector Construction The antenna connector used in this product is internal antenna, cannot be replaced by the end-user. See section 2 – antenna information. 21 of 33

@l Report Number: 1904FR12 Rev.00 5 Test Results Annex A. Conducted Emission Standard: FCGC Part 16.226 Line: L Test tem: Conducted Emission Power: AG 120 Vieo Hz Test Mode: Mode 1 Temp.(C)/Hum.(RH): 26(C)/60 %RH Description: sn0 avwr T tinie: — a.150 as it 5 30000 No.| Frequency oP AvG Correction oP AG oP AG oP AG Remark reading reading factor resul result Iimt lt margn margin (via) (iBuw) (dBuw CB) (Buy) (dBuw (aBus) (aBus CB) CB) 1 0.1580 3742 23.03 952 40.06 3255 65.57 58.57 +1863 —23.02 Pass 2 0.1820 33.00 1875 952 4261 227 6439 54.39 «2178 ESAH Pass 3 02060 33.08 10.87 952 43.40 2619 63.37 53.37 +19.07 2718 Pass 4 18560 26.20 15.70 860 35.09 25.30 56.00 46.00 »20.11 —20.70 Pass 5 13.7780 17.76 10.28 981 2757 20.00 €0.00 50.00 3243 «2201 Pass 6 24,1080 18.2¢ 11.86 988 2812 2172 €0.00 50.00 «3188 2828 Pass Note: 1. Result (dBu\) = Correction factor (dB) + Reading(dBuV). 2. Correction factor (dB) = Cable loss (dB) + LL.SN. factor (dB). 22 of 33

‘ n t' Report Number: 1904FR12 \4 Rev.00 Standard: FCC Part 15225 Line: N Test item: Conducted Emission Power: AC 120 ViBO Hz Test Mode: Mode 1 Temp.(C)/Hum.(RH): 26(C)/60 %RH Description: mo n T tinie: — a.150 as it 5 30000 No.| Frequency| OP AVG Correction| OP awe or awe or AVG Remaid reading reading factor resut resut lim it margn margin ie (Bay Bay 19 wew weay |uy caBuy @9 CB) 1| omseo sz10 2148 aso «e70 sios saze sere 19008 2670 Pass 2 or800 sase 2008 aso «ai7 seer sa0e seoe 2087 2637 Pass s oaseo zeor iss aso sses sos eair s2ir 2est —2528 Pass « ozeeo 2ame 1482 aso sem men coss some 2a8s —2668 Pass s nes00 meos is2 ase sazo mos seoo «s00 2280 —21.07 Pass s t20m00 2138 reas aso si22 mss eomo sone 2a78 —25.02 Pass Note: 1. Result (dBu\) = Correction factor (dB) + Reading(dBuV). 2. Correction factor (dB) = Cable loss (dB) + LL.SN. factor (dB). 23 of 33

@l Report Number: 19047R 12 Rev.00 Annex B. Conducted Test Results Frequency Stability Measurement Temperature Variations Test Mode Mode 2 Omnute Zmnuts Smnus 10mnues Temp Voltege Frequency Frequency Frequency Frequency Limit Resut (‘0) (VAC) Tolerance Tolerance Tolerance Tolerance (%) (PassiFall) (%) (%) (%) (%) 20 Viion 00071 —o.0070 —o0074 —o 074 10 01 Pass —10 Viion —o.0088 —o.ooss —0.0085 —o.0088 10 01 Pass 0 Yin —o.o0ss —o.ooss —oo058 —o.0053 10 01 Pass 10 Yin —o.0058 —o.ooss —oo058 o 0057 10 01 Pass 20 Yion —0.0055 —0.0055 —0.0055 —0.0055 £0.01 Pass so Viion —o.0088 —o.coss —o.0050 —o.0088 10 01 Pass «o Viion —o.005s —o.ooss —0.0085 —o.0088 10 01 Pass so Yin —o.0088 —o.ooss —0.0085 —o.0088 10 01 Pass so Yin —o.0088 —o.ooss —0.0085 —o 074 10 01 Pass Voltage Variations Test Mode Mode 2 Omnute Zmnues Smnues 10 mnues Temp Vottege Frequency Frequency Frequency Frequency Limit Result (‘0) (VAC) Tolerance Tolerance Tolerance Tolerance (%) (Pess/Fall) (%) (%) (%) (%) View —o.ooss —0.008 —o.008s —o.0088 10 01 Pass 20 Vien —o.0055 —0.0055 —0.0055 —0.0055 +0 .01 Pass Vie —o.ooss —o0083 —o.008s —o.005s 10 01 Pass Not®: Viee=Vier—15 % ; Vigr=Vien15 % 24 of 33

Report Number: 1904FR12 Rev.00 20 dB Bandwidth Measurement Test Mode Mode 2 Frequency 20 dBc Low Point 20 dBc High Point Operating Frequency Band (MHz) (MHz) (MHz) (MHz) 13.5600 13.55865 13.56355 13.553~13.567  Test Graphs 25 of 33

@l Report Number: 1904FR12 Rev.00 Annex C. Radiated Emission Measurement Fundamental Test Result: Standard: FCC Part 15.225 Test Distance: 1 m Test item: Fundamental Power: AC 120 V/6O Hz Test Mode: Mode 2 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar.: Horizontal 1500 dtwv/m Tman: — m — : is sn rass0 se vass Ta5e Tase Tase Take Tss msr Tear hn No. Frequency Reading Correct Factor NERE;TITM D\Z::e: Limit Margin Remark (MHz) (dBuv) (dB/m) (dBuv) (dBuV) (dBuvim) (4B) 1 13.5610 52.80 37.80 90.60 50.13 84.00 "33.87 peak Note: The level is measured at 1 meter and is converted into result at 30 meter. The converted formula listed below: Measure result (1 meter distance}: a Compute result (30 meter distance): A C nesrfels N2T > Uneasice = 1 meter distance A= a ~ 4OTGG(Unearteis HAmeasire) ~ 20"1Og(dimnl Cheartels) ex. a =90.6 dBuV, A=80.6 — 40%og(3.52 /1 ) — 20og(30 /3.52 ) dBuV = 50.13 dBu 26 of 33

@l Report Number: 1904FR12 Rev.00 Standard: FCC Part 15.225 Test Distance: 1 m Test item: Fundamental Power: AC 120 V/GD Hz Test Mode: Mode 2 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar. Vertical 1500 dtwv/m T: — m — : is sn rass0 se vass Ta5e Tase Tase Take Tss msr T357 ie Near—Field D d Frequency Reading Correct Factor car io orve Limit Margin No. Result Value Remark (MHz) (dBuy) (dB/m) (dBuy) (dBuy) (@Buvim) (48) 1 135610 54.20 37.80 92.00 51.62 84.00 —32.38 peak Note: The level is measured at 1 meter and is converted into result at 30 meter. 27 of 33

@l Report Number: 1904FR12 Rev.00 9 kHz~ 30 MHz: Standard: FCC Part 15.225 Test Distance: 300/30 m Test item: Harmonic Power: AC 120 V/GD Hz Test Mode: Mode 2 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar. Horizontal 1700 dbwv/m T: — Margine — [ 1 zol , 2 4 $ a0 aods 307 sn s 20 o0 Teod 2100 2i00 5000 une No: Frequency Reading Correct Factor NERE;TITM D\Z::e: Limit Margin Remark (MHz) (dBuv) (dB/m) (dBuVim) (dBuV) (dBuvim) (4B) 1 0.6088 34.30 44.31 78.70 11.27 31.91 —20.65 aP 2 1.2686 22.14 40.67 62.81 1.75 25.54 —23.78 aP 3 2.3783 4.88 38.38 43.26 —12.34 20.54 ~41.88 aP 4 3.1281 6.24 37.06 43.30 —0.01 20.54 —30.46 aP 5 4.2077 12.08 37.06 49.14 4132 20.54 —30.86 aP 6 7.6267 —1.38 37.64 36.26 —8.21 20.54 —38.76 aP Note: The level is measured at 1 meter and is converted into result at 300 or 30 meter. 28 of 33

@l Report Number: 1904FR12 Rev.00 Standard: FCC Part 15.225 Test Distance: 300/30 m Test item: Harmonic Power: AC 120 V/GD Hz Test Mode: Mode 2 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar. Vertical 1700 dbwyym T: — Margine — [ i 7o 3 t4 58 a0 aods 30 sn am 20 o0 Teod 2100 2i00 5000 une Near—Field D d Frequency Reading Correct Factor car io orve Limit Margin No. Result Value Remark (MHz) (dBuv) (dB/m) (dBuVim) (dBuV) (dBuvim) (4B) 1 0.6088 36.18 44.31 80.49 13.06 31.91 —18.86 aP 2 1.2086 18.00 40.61 58.61 224 25.33 —27.58 aP 3 4.0577 12.06 37.06 49.12 —1.84 20.54 —31.38 aP 4 4.5376 9.83 37.05 46.88 310 20.54 —32.65 aP 5 7.5067 —1.79 37.63 35.84 —0.68 20.54 —80.22 aP 6 8.2265 214 37.78 35.64 —0.17 20.54 —38.71 aP Note: The level is measured at 1 meter and is converted into result at 300 or 30 meter. 29 of 33

( fltl Report Number: 1904FR12 Rev.00 30 MHz~ 1 GHz: Standard: FCC Part 15.225 Test Distance: 3m Test item: Harmonic Power: AC 120 V/GD Hz Test Mode: Mode 2 Temp.(‘C)/Hum.(%RH): 26(°C)/60 %RH Ant.Polar. Horizontal s00 aburm T: — Margine — ao _A F 3 & & R 1 as st.ooo —rzroe 2raue seion mace sisa0 bi200 7osod Sco0 T00000° une Frequency Reading Correct Factor Result Limit Margin No. Remark (MHz) (dBuv) (dB/m) (dBuVim) (dBuvim) (d8) 1 310.3300 27.01 —3.58 2343 46.00 —22.57 aP 2 521.7900 3220 0.58 32.87 46.00 1313 aP 3 ©60.2300 27.70 3.60 31.30 46.00 —14.70 aP 4 746.8300 28.80 5.44 34.33 46.00 ~11.67 aP 5 860.0500 27.62 7.30 34.02 46.00 —11.08 aP 6 932.1000 27.64 8.37 36.01 46.00 —0.99 aP 30 of 33

( fltl Report Number: 1904FR12 Rev.00 Standard: FCC Part 15.225 Test Distance: 3m Test item: Harmonic Power: AC 120 V/GD Hz Test Mode: Mode 2 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar. Vertical s00 aburm T: — Margine — «0 3 2 44 as st.ooo —rzroe 2raue spion maco SS 00 bi200 7500 S0e00 To0000° un Frequency Reading Correct Factor Result Limit Margin No. Remark (MHz) (dBuv) (dB/m) (dBuVim) (dBuvim) (d8) 1 517.0100 37.62 0.51 38.13 46.00 7.87 aP 2 746.8300 3290 5.44 38.34 46.00 —7.66 aP 3 792.4200 31.17 6.23 3740 46.00 —8.60 aP 4 816.6700 3148 6.56 38.04 46.00 —7.96 aP 5 830.0500 3230 6.86 30.25 46.00 —6.75 aP 6 874.8700 31.27 7.30 38.66 46.00 —7.34 aP 31 of 33

( fltl Report Number: 1904FR12 Rev.00 Standard: FCC Part 15.225 Test Distance: 3m Test item: Harmonic Power: AC 120 V/GD Hz Test Mode: Mode 3 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar. Horizontal s00 aburm T: — Margine — «n & i« ; |__—I 1 as st.ooo —rzroe 2raue spion maco sis00 bi200 7os0 so600 T00000° un Frequency Reading Correct Factor Result Limit Margin No. Remark (MHz) (dBuv) (dB/m) (dBuVim) (dBuvim) (d8) 1 515.0700 3142 0.47 31.80 46.00 1441 aP 2 €50.8000 36.08 325 30.33 46.00 —6.67 aP 3 788.5400 3354 617 30.71 46.00 —6.20 aP 4 812.7900 31.04 6.51 37.55 46.00 845 aP 5 874.8700 20.34 7.30 36.73 46.00 —0.27 aP 6 933.0700 27.24 8.30 35.63 46.00 —10.37 aP 32 of 33

( fltl Report Number: 1904FR12 Rev.00 Standard: FCC Part 15.225 Test Distance: 3m Test item: Harmonic Power: AC 120 V/GD Hz Test Mode: Mode 3 Temp.(‘C)/Hum:(%RH): 26(CC)/60 %RH Ant.Polar. Vertical s00 aburm T: — Margine — 10 1 £2 2oR os as st.ooo —rzroe 2raue spion maco sisa0 bi200 7osod Soco0 T00000° un Frequency Reading Correct Factor Result Limit Margin No. Remark (MHz) (dBuv) (dB/m) (dBuVim) (dBuvim) (d8) 1 §22.7600 38.06 0.50 30.55 46.00 6.46 aP 2 720.3700 36.24 4.97 41.21 46.00 ~4.79 aP 3 746.8300 34.02 5.44 40.36 46.00 —5.64 aP 4 830.0500 30.83 6.86 37.60 46.00 831 aP 5 875.8400 33.37 742 40.79 46.00 —6.21 aP 6 934.0400 30.04 8.40 30.34 46.00 —6.66 aP 33 of 33


Document Created: 2019-05-23 05:12:17
Document Modified: 2019-05-23 05:12:17
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC