1703TW0106-U6-FCC-UNII Test Report Part1

FCC ID: Q9DAPINH203

Test Report

Download: PDF
FCCID_3458649

MRT Technology (Taiwan) Co., Ltd Report No.: 1703TW0106-U6 Phone: +886-3-3288388 Report Version: V01 Fax: +886-3-3288918 Issue Date: 06-02-2017 Web: www.mrt-cert.com MEASUREMENT REPORT FCC PART 15 Subpart E WLAN 802.11a/n/ac FCC ID: Q9DAPINH203 APPLICANT: Hewlett Packard Enterprise Company Application Type: Class III Permissible Change Product: ACCESS POINT Model No.: APINH203 Brand Name: , FCC Classification: Unlicensed National Information Infrastructure (UNII) FCC Rule Part(s): Part 15 Subpart E (Section 15.407) Test Procedure(s): ANSI C63.10-2013, KDB 789033 D02v01r03, KDB 662911 D01v02r01, KDB 644545 D03v01 Test Date: December 28, 2016 ~ May 23, 2017 Reviewed By : ( Paddy Chen ) Approved By : ( Chenz Ker ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 789033 D02v01r03. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Taiwan) Co., Ltd. FCC ID: Q9DAPINH203 Page Number: 1 of 406

Report No.: 1703TW0106-U6 Revision History Report No. Version Description Issue Date Note 1703TW0106-U6 Rev. 01 Initial report 06-02-2017 Valid FCC ID: Q9DAPINH203 Page Number: 2 of 406

Report No.: 1703TW0106-U6 CONTENTS Description Page §2.1033 General Information ......................................................................................................... 5 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description.................................................................................................. 7 2.2. Product Specification Subjective to this Report ............................................................. 7 2.3. Operating Frequency and Channel List......................................................................... 8 2.4. Description of Available Antennas ................................................................................. 9 2.5. Description of Antenna RF Port .................................................................................... 9 2.6. Test Mode .................................................................................................................. 10 2.7. Description of Test Software ....................................................................................... 10 2.8. Device Capabilities ..................................................................................................... 13 2.9. Test Configuration ...................................................................................................... 15 2.10. EMI Suppression Device(s)/Modifications ................................................................... 15 2.11. Labeling Requirements ............................................................................................... 15 3. DESCRIPTION OF TEST ...................................................................................................... 16 3.1. Evaluation Procedure ................................................................................................. 16 3.2. AC Line Conducted Emissions ................................................................................... 16 3.3. Radiated Emissions .................................................................................................... 17 4. ANTENNA REQUIREMENTS ................................................................................................ 18 5. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 19 6. MEASUREMENT UNCERTAINTY ......................................................................................... 21 7. TEST RESULT ...................................................................................................................... 22 7.1. Summary .................................................................................................................... 22 7.2. 26dB Bandwidth Measurement ................................................................................... 23 7.2.1. Test Limit .................................................................................................................... 23 7.2.2. Test Procedure used ................................................................................................... 23 7.2.3. Test Setting ................................................................................................................. 23 7.2.4. Test Setup .................................................................................................................. 23 7.2.5. Test Result .................................................................................................................. 24 7.3. Output Power Measurement ....................................................................................... 37 7.3.1. Test Limit .................................................................................................................... 37 FCC ID: Q9DAPINH203 Page Number: 3 of 406

Report No.: 1703TW0106-U6 7.3.2. Test Procedure Used .................................................................................................. 37 7.3.3. Test Setting ................................................................................................................. 37 7.3.4. Test Setup .................................................................................................................. 37 7.3.5. Test Result .................................................................................................................. 38 7.4. Transmit Power Control .............................................................................................. 45 7.4.1. Test Limit .................................................................................................................... 45 7.4.2. Test Procedure Used .................................................................................................. 45 7.4.3. Test Setting ................................................................................................................. 45 7.4.4. Test Setup .................................................................................................................. 45 7.4.5. Test Result .................................................................................................................. 45 7.5. Power Spectral Density Measurement ........................................................................ 46 7.5.1. Test Limit .................................................................................................................... 46 7.5.2. Test Procedure Used .................................................................................................. 46 7.5.3. Test Setting ................................................................................................................. 46 7.5.4. Test Setup .................................................................................................................. 47 7.5.5. Test Result .................................................................................................................. 48 7.6. Frequency Stability Measurement ............................................................................... 95 7.6.1. Test Limit .................................................................................................................... 95 7.6.2. Test Procedure Used .................................................................................................. 95 7.6.3. Test Setup .................................................................................................................. 95 7.6.4. Test Result .................................................................................................................. 96 7.7. Radiated Spurious Emission Measurement ................................................................ 97 7.7.1. Test Limit .................................................................................................................... 97 7.7.2. Test Procedure Used .................................................................................................. 97 7.7.3. Test Setting ................................................................................................................. 97 7.7.4. Test Setup .................................................................................................................. 98 7.7.5. Test Result ................................................................................................................ 100 7.8. Radiated Restricted Band Edge Measurement ......................................................... 204 7.8.1. Test Limit .................................................................................................................. 204 7.8.2. Test Result of Radiated Restricted Band Edge ......................................................... 206 7.9. AC Conducted Emissions Measurement................................................................... 402 7.9.1. Test Limit .................................................................................................................. 402 7.9.2. Test Procedure ......................................................................................................... 402 7.9.3. Test Setup ................................................................................................................ 403 7.9.4. Test Result ................................................................................................................ 404 8. CONCLUSION..................................................................................................................... 406 FCC ID: Q9DAPINH203 Page Number: 4 of 406

Report No.: 1703TW0106-U6 §2.1033 General Information Applicant: Hewlett Packard Enterprise Company Applicant Address: 3000 Hanover St. Palo Alto, CA 94304, USA Manufacturer: Hewlett Packard Enterprise Company Manufacturer Address: 3000 Hanover St. Palo Alto, CA 94304, USA Test Site: MRT Technology (Taiwan) Co., Ltd Test Site Address: No. 38, Fuxing Second Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C) MRT Registration No.: 153292 FCC Rule Part(s): Part 15.407 Model No.: APINH203 FCC ID: Q9DAPINH203 Test Device Serial No.: CNCKK2S0W2 Production Pre-Production Engineering FCC Classification: Unlicensed National Information Infrastructure (UNII) Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Fuxing Rd., Taoyuan, Taiwan ( R.O.C )  MRT facility is a FCC registered (MRT Reg. No. 153292) test facility with the site description report on file and is designated by the FCC as an Accredited Test Film.  MRT facility is an IC registered (MRT Reg. No. 21723-1) test laboratory with the site description on file at Industry Canada.  MRT Lab is accredited to ISO 17025 by the American TAF certificate here Association for Laboratory Accreditation (TAF) under the American Association for Laboratory Accreditation Program (TAF Cert. No. 3261) in EMC, Telecommunications and Radio testing for FCC, Industry Canada, Taiwan, EU and TELEC Rules. FCC ID: Q9DAPINH203 Page Number: 5 of 406

Report No.: 1703TW0106-U6 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2. MRT Test Location sThe map below shows the location of the MRT LABORATORY, its proximity to the Taoyuan City. These measurement tests were conducted at the MRT Technology (Taiwan) Co., Ltd. Facility located at No.38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 33377, Taiwan (R.O.C). FCC ID: Q9DAPINH203 Page Number: 6 of 406

Report No.: 1703TW0106-U6 2. PRODUCT INFORMATION 2.1. Equipment Description Product Name: ACCESS POINT Model No.: APINH203 Brand Name: , Software Version: 9.10 RC178.40 e5.0.9.1 Operating Temperature: 0 ~ 40 °C Power Type: POE input Wi-Fi Specification: 802.11a/b/g/n/ac Note: The applicant has provided one POE adapter (Manufacturer: MICROSEMI & Model: PD-9001GR/AT/AC & Output: 55VDC, 0.6A) for approval testing and it is not for sale. 2.2. Product Specification Subjective to this Report Frequency Range: For 802.11a/n-HT20/ ac-VHT20: 5240~5320MHz, 5500~5720MHz For 802.11n-HT40/ac-VHT40: 5230~5310MHz, 5510~5710MHz For 802.11ac-VHT80: 5290MHz, 5530MHz, 5610MHz, 5690MHz Type of Modulation: 802.11a/n/ac: OFDM Data Rate: 802.11a: 6/9/12/18/24/36/48/54Mbps 802.11n: up to 300Mbps 802.11ac: up to 866.6Mbps Maximum Average 802.11a: 19.79dBm Output Power: 802.11n-HT20: 19.83dBm 802.11n-HT40: 19.87dBm 802.11ac-VHT20: 19.72dBm 802.11ac-VHT40: 19.98dBm 802.11ac-VHT80: 19.46dBm Note: For other features of this EUT, test report will be issued separately. FCC ID: Q9DAPINH203 Page Number: 7 of 406

Report No.: 1703TW0106-U6 2.3. Operating Frequency and Channel List 802.11a/n-HT20/ac-VHT20 Channel Frequency Channel Frequency Channel Frequency 52 5260 MHz 56 5280 MHz 60 5300 MHz 64 5320 MHz 100 5500 MHz 104 5520 MHz 108 5540 MHz 112 5560 MHz 116 5580 MHz 120 5600 MHz 124 5620 MHz 128 5640 MHz 132 5660 MHz 136 5680 MHz 140 5700 MHz 144 5720 MHz -- -- -- -- 802.11n-HT40/ac-VHT40 Channel Frequency Channel Frequency Channel Frequency 54 5270 MHz 62 5310 MHz 102 5510 MHz 110 5550 MHz 118 5590 MHz 126 5630 MHz 134 5670 MHz 142 5710 MHz -- -- 802.11ac-VHT80 Channel Frequency Channel Frequency Channel Frequency 58 5290 MHz 106 5530 MHz 122 5610 MHz 138 5690 MHz -- -- -- -- FCC ID: Q9DAPINH203 Page Number: 8 of 406

Report No.: 1703TW0106-U6 2.4. Description of Available Antennas Antenna Type Frequency Band TX Paths Max Antenna Gain Directional Gain (MHz) (dBi) (dBi) 1 (Note 3) 4.3 N/A 2412 ~ 2462 PCB 2 3.8 6.8 Antenna 1 (Note 3) 6.3 N/A 5150 ~ 5850 2 4.0 7.0 Note 1: The EUT supports Cyclic Delay Diversity (CDD) technology for 802.11a/b/g/n/ac mode, and the transmitter output signal is correlated. For CDD transmissions, directional gain = GANT + Array Gain, Array Gain = 3.0 dBi which is declared by the applicant. For power measurements on IEEE 802.11 devices, Array Gain = 0 dB for NANT ≤ 4. Note 2: The EUT also supports Beam Forming technology, and the Beam Forming only support 802.11n/ac mode. Directional gain = GANT + BF Gain, BF Gain = 3.0 dBi which is declared by the applicant. Note 3: For SISO mode, only Ant 2 port can transmit 2.4GHz and Ant 1 port can transmit 5GHz. 2.5. Description of Antenna RF Port Antenna RF Port -- 2.4GHz RF Port 5GHz RF Port Software Control Port for 1Tx -- Ant 2 Ant 1 -- Software Control Port for 2Tx Ant 1 Ant 2 Ant 1 Ant 2 FCC ID: Q9DAPINH203 Page Number: 9 of 406

Report No.: 1703TW0106-U6 2.6. Test Mode Test Mode Mode 1: Transmit by 802.11a Mode 2: Transmit by 802.11n-HT20 (CDD Mode / Beam-Forming Mode) Mode 3: Transmit by 802.11n-HT40 (CDD Mode / Beam-Forming Mode) Mode 4: Transmit by 802.11ac-VHT20 (CDD Mode / Beam-Forming Mode) Mode 5: Transmit by 802.11ac-VHT40 (CDD Mode / Beam-Forming Mode) Mode 6: Transmit by 802.11ac-VHT80 (CDD Mode / Beam-Forming Mode) 2.7. Description of Test Software The test utility software used during testing was “AcctonMTool.exe”. 1TX _ Ant 1 Test Test Power Parameter Test Test Power Parameter Mode Frequency Value Mode Frequency Value 5260 64.0 5260 66.0 5300 64.0 5300 66.0 5320 64.0 5320 66.0 802.11n- 802.11a 5500 66.0 5500 66.0 HT20 5600 66.0 5600 66.0 5700 66.0 5700 66.0 5720 66.0 5720 66.0 5260 64.0 5270 64.0 5300 64.0 5310 60.0 5320 64.0 802.11n- 5510 56.0 802.11ac- 5500 66.0 HT40 5590 66.0 VHT20 5600 66.0 5670 66.0 5700 66.0 5710 66.0 5720 66.0 5270 64.0 5290 60.0 5310 60.0 802.11ac- 5530 58.0 802.11ac- 5510 56.0 VHT80 5610 66.0 VHT40 5590 66.0 5690 66.0 5670 66.0 5710 66.0 FCC ID: Q9DAPINH203 Page Number: 10 of 406

Report No.: 1703TW0106-U6 CDD Mode 2TX _ Ant 1 + 2 Test Test Power Parameter Test Test Power Parameter Mode Frequency Value Mode Frequency Value 5260 64.0 5260 64.0 5300 64.0 5300 64.0 5320 64.0 5320 64.0 802.11n- 802.11a 5500 66.0 5500 60.0 HT20 5600 66.0 5600 66.0 5700 60.0 5700 62.0 5720 68.0 5720 68.0 5260 64.0 5270 64.0 5300 64.0 5310 56.0 5320 64.0 802.11n- 5510 50.0 802.11ac- 5500 60.0 HT40 5590 66.0 VHT20 5600 66.0 5670 66.0 5700 60.0 5710 66.0 5720 68.0 5270 64.0 5290 50.0 5310 54.0 802.11ac- 5530 46.0 802.11ac- 5510 48.0 VHT80 5610 68.0 VHT40 5590 66.0 5690 68.0 5670 62.0 5710 68.0 FCC ID: Q9DAPINH203 Page Number: 11 of 406

Report No.: 1703TW0106-U6 Beam-Forming Mode 2TX _ Ant 1 + 2 Test Test Power Parameter Test Test Power Parameter Mode Frequency Value Mode Frequency Value 5260 64.0 5270 64.0 5300 64.0 5310 50.0 5320 64.0 802.11n- 5510 56.0 802.11n- 5500 58.0 HT40 5590 66.0 HT20 5600 64.0 5670 66.0 5700 56.0 5710 68.0 5720 64.0 5270 68.0 5260 64.0 5310 50.0 5300 64.0 802.11ac- 5510 50.0 5320 64.0 VHT40 5590 68.0 802.11ac- 5500 60.0 5670 68.0 VHT20 5600 64.0 5710 68.0 5700 62.0 5290 54.0 5720 68.0 802.11ac- 5530 58.0 VHT80 5610 66.0 5690 66.0 FCC ID: Q9DAPINH203 Page Number: 12 of 406

Report No.: 1703TW0106-U6 2.8. Device Capabilities This device contains the following capabilities: 2.4GHz WLAN (DTS) and 5GHz WLAN (NII) Note: 5GHz (NII) operation is possible in 20MHz, 40MHz and 80MHz channel bandwidths. The maximum achievable duty cycles for all modes were determined based on measurements performed on a spectrum analyzer in zero-span mode with RBW = 8MHz, VBW = 50MHz, and detector = average per the guidance of Section B)2)b) of KDB 789033 D02v01r03. The RBW and VBW were both greater than 50/T, where T is the minimum transmission duration, and the number of sweep points across T was greater than 100. The duty cycles are as follows: Test Mode Duty Cycle 802.11a 95.16 % 802.11n-HT20 95.05 % 802.11n-HT40 90.41 % 802.11ac-VHT20 98.47 % 802.11ac-VHT40 97.03 % 802.11ac-VHT80 93.79 % 802.11a 802.11n-HT20 FCC ID: Q9DAPINH203 Page Number: 13 of 406

Report No.: 1703TW0106-U6 802.11n-HT40 802.11ac-VHT20 802.11ac-VHT40 802.11ac-VHT80 FCC ID: Q9DAPINH203 Page Number: 14 of 406

Report No.: 1703TW0106-U6 2.9. Test Configuration The ACCESS POINT was tested per the guidance of KDB 789033 D02v01r03. ANSI C63.10-2013 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. 2.10. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. 2.11. Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label and label location. FCC ID: Q9DAPINH203 Page Number: 15 of 406

Report No.: 1703TW0106-U6 3. DESCRIPTION OF TEST 3.1. Evaluation Procedure The measurement procedures described in the American National Standard for Testing Unlicensed Wireless Devices (ANSI C63.10-2013), and the guidance provided in KDB 789033 D02v01r03 were used in the measurement of the ACCESS POINT. Deviation from measurement procedure…………………………….....................................None 3.2. AC Line Conducted Emissions The line-conducted facility is located inside an 8'x4'x4' shielded enclosure. A 1m x 2m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50Ω/50uH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference ground-plane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the receiver and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The receiver was scanned from 150kHz to 30MHz. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 9kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Each emission was also maximized by varying: power lines, the mode of operation or data exchange speed, or support equipment whichever determined the worst-case emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions are used for final measurements on the same test site. The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final measurements. An extension cord was used to connect to a single LISN which powered by EUT. The extension cord was calibrated with LISN, the impedance and insertion loss are compliance with the requirements as stated in ANSI C63.10-2013. Line conducted emissions test results are shown in Section 7.8. FCC ID: Q9DAPINH203 Page Number: 16 of 406

Report No.: 1703TW0106-U6 3.3. Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. A MF Model 210SS turntable is used for radiated measurement. It is a continuously rotatable, remote controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm high PVC support structure is placed on top of the turntable. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up for frequencies below 1GHz was placed on top of the 0.8 meter high, 1 x 1.5 meter table; and test set-up for frequencies 1-40GHz was placed on top of the 1.5 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. According to 3dB Beam-Width of horn antenna, the horn antenna should be always directed to the EUT when rising height. FCC ID: Q9DAPINH203 Page Number: 17 of 406

Report No.: 1703TW0106-U6 4. ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna of the ACCESS POINT is permanently attached.  There are no provisions for connection to an external antenna. Conclusion: The ACCESS POINT unit complies with the requirement of §15.203. FCC ID: Q9DAPINH203 Page Number: 18 of 406

Report No.: 1703TW0106-U6 5. TEST EQUIPMENT CALIBRATION DATE Conducted Emissions - SR2 Instrument Manufacturer Type No. Asset No. Cali. Due Date Two-Line V-Network R&S ENV216 MRTTWA00019 2017.03.23 Two-Line V-Network R&S ENV216 MRTTWA00020 2017.03.23 Absorbing Clamp R&S MDS21 MRTTWA00016 2017.03.02 EMI Test Receiver R&S ESR3 MRTTWA00009 2017.03.17 N1C50-RG400-B1 Conducted Cable Rosnol MRTTWE00013 2017.05.20 C50-500CM Temperature/Humidity Meter TFA 35.1078.10.IT MRTTWA00033 2017.06.09 Radiated Spurious Emission and Radiated Restricted Band Edge - AC1 Instrument Manufacturer Type No. Asset No. Cali. Due Date 2017.04.06 Acitve Loop Antenna SCHWARZBECK FMZB 1519B MRTTWA00002 2018.04.06 2017.04.06 Broadband TRILOG Antenna SCHWARZBECK VULB 9162 MRTTWA00001 2018.04.06 2017.04.06 Broadband Hornantenna SCHWARZBECK BBHA 9120D MRTTWA00003 2018.04.06 2017.04.06 Breitband Hornantenna SCHWARZBECK BBHA 9170 MRTTWA00004 2018.04.06 2017.04.06 Broadband Preamplifier SCHWARZBECK BBV 9718 MRTTWA00005 2018.04.06 2017.04.06 Broadband Amplifier SCHWARZBECK BBV 9721 MRTTWA00006 2018.04.06 2017.03.02 Signal Analyzer R&S FSV40 MRTTWA00007 2018.03.02 EXA Signal Analyzer KEYSIGHT N9010A MRTTWA00012 2017.07.11 2017.05.20 Antenna Cable HUBERSUHNER SF106 MRTTWE00010 2018.05.20 FCC ID: Q9DAPINH203 Page Number: 19 of 406

Report No.: 1703TW0106-U6 Conducted Test Equipment - SR1 Instrument Manufacturer Type No. Asset No. Cali. Due Date 2017.03.02 Signal Analyzer R&S FSV40 MRTTWA00007 2018.03.02 EXA Signal Analyzer KEYSIGHT N9010A MRTTWA00012 2017.07.11 2017.05.08 USB wideband power sensor Boonton 55006 MRTTWA00050 2018.05.08 X-Series USB Peak and 2017.03.18 KEYSIGHT U2021XA MRTTWA00014 Average Power Sensor 2018.03.18 Software Version Function e3 V 8.3.5 EMI Test Software FCC ID: Q9DAPINH203 Page Number: 20 of 406

Report No.: 1703TW0106-U6 6. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement - SR2 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 150kHz~30MHz: 3.46dB Radiated Emission Measurement - AC1 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 9kHz ~ 1GHz: 4.18dB 1GHz ~ 40GHz: 4.76dB Output Power - SR1 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 1.13dB Power Spectrum Density - SR1 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 1.15dB Occupied Bandwidth - SR1 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 0.28% FCC ID: Q9DAPINH203 Page Number: 21 of 406

Report No.: 1703TW0106-U6 7. TEST RESULT 7.1. Summary Product Name: ACCESS POINT FCC ID: Q9DAPINH203 FCC Classification: Unlicensed National Information Infrastructure (UNII) Data Rate / MCS 6Mbps for 802.11a; Tested: MCS0 for 802.11n-HT20MHz; MCS0 for 802.11n-HT40MHz; MCS0 for 802.11ac-VHT20MHz; MCS0 for 802.11ac-VHT40MHz; MCS0 for 802.11ac-VHT80MHz FCC Test Test Test Description Test Limit Reference Section(s) Condition Result 15.407(a) 26dB Bandwidth N/A Pass Section 7.2 Maximum Conducted 15.407(a)(2) ≤ 24 dBm U-NII-2A & 2C Pass Section 7.3 Output Power Conducted 15.407(a)(2), Peak Power Spectral ≤ 11 dBm/MHz U-NII-2A&2C Pass Section 7.4 (5) Density 15.407(g) Frequency Stability N/A Pass Section 7.5 15.407(b)(2), Undesirable Detail see section 7.8 Pass (3) Emissions General Field Strength Emissions in restricted Section 15.205, 15.209 Radiated Limits (Restricted bands must meet the 7.6 & 7.7 15.407(b)(5), Pass Bands and Radiated radiated limits detailed in (6), (7) Emission Limits) 15.209 AC Conducted Line 15.207 Emissions < FCC 15.207 limits Pass Section 7.8 Conducted 150kHz - 30MHz Notes: 1) The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. 2) Test Items “26dB Bandwidth” & “6dB Bandwidth” & “Frequency Stability” have been assessed MIMO transmission, and showed the worst single test data in this report. FCC ID: Q9DAPINH203 Page Number: 22 of 406

Report No.: 1703TW0106-U6 7.2. 26dB Bandwidth Measurement 7.2.1. Test Limit N/A 7.2.2. Test Procedure used KDB 789033 D02v01r03 - Section C.1 7.2.3. Test Setting 1. The analyzers’ automatic bandwidth measurement capability was used to perform the 26dB bandwidth measurement. The “X” dB bandwidth parameter was set to X = 26. The automatic bandwidth measurement function also has the capability of simultaneously measuring the 99% occupied bandwidth. The bandwidth measurement was not influenced by any intermediated power nulls in the fundamental emission. 2. RBW = approximately 1% of the emission bandwidth. 3. VBW ≥ 3 × RBW. 4. Detector = Peak. 5. Trace mode = max hold. 7.2.4. Test Setup FCC ID: Q9DAPINH203 Page Number: 23 of 406

Report No.: 1703TW0106-U6 7.2.5. Test Result Product ACCESS POINT Temperature 22°C Test Engineer Kevin Ker Relative Humidity 54% Test Site SR1 Test Date 2016/12/29 Test Mode Data Rate / Channel No. Frequency 26dB Bandwidth 99% Bandwidth Result MCS (MHz) (MHz) (MHz) Ant 1 802.11a 6Mbps 52 5260 21.24 16.83 Pass 802.11a 6Mbps 60 5300 21.32 16.81 Pass 802.11a 6Mbps 64 5320 21.29 16.78 Pass 802.11a 6Mbps 100 5500 21.53 16.83 Pass 802.11a 6Mbps 120 5600 21.62 16.87 Pass 802.11a 6Mbps 140 5700 21.37 16.89 Pass 802.11a 6Mbps 144 5720 21.77 16.94 Pass 802.11n-HT20 MCS0 52 5260 21.78 18.00 Pass 802.11n-HT20 MCS0 60 5300 21.72 17.97 Pass 802.11n-HT20 MCS0 64 5320 21.72 18.00 Pass 802.11n-HT20 MCS0 100 5500 22.84 18.02 Pass 802.11n-HT20 MCS0 120 5600 23.35 18.06 Pass 802.11n-HT20 MCS0 140 5700 22.12 18.04 Pass 802.11n-HT20 MCS0 144 5720 22.07 18.04 Pass 802.11n-HT40 MCS0 54 5270 41.89 36.46 Pass 802.11n-HT40 MCS0 62 5310 40.37 36.43 Pass 802.11n-HT40 MCS0 102 5510 40.24 36.43 Pass 802.11n-HT40 MCS0 118 5590 44.78 36.55 Pass 802.11n-HT40 MCS0 134 5670 40.55 36.46 Pass 802.11n-HT40 MCS0 142 5710 53.43 36.49 Pass 802.11ac-VHT20 MCS0 52 5260 21.68 18.00 Pass 802.11ac-VHT20 MCS0 60 5300 21.78 18.02 Pass 802.11ac-VHT20 MCS0 64 5320 21.78 18.00 Pass 802.11ac-VHT20 MCS0 100 5500 22.26 18.04 Pass 802.11ac-VHT20 MCS0 120 5600 21.94 18.08 Pass 802.11ac-VHT20 MCS0 140 5700 21.94 18.03 Pass 802.11ac-VHT20 MCS0 144 5720 22.08 18.08 Pass FCC ID: Q9DAPINH203 Page Number: 24 of 406

Report No.: 1703TW0106-U6 Test Mode Data Rate / Channel No. Frequency 26dB Bandwidth 99% Bandwidth Result MCS (MHz) (MHz) (MHz) Ant 1 802.11ac-VHT40 MCS0 54 5270 40.29 36.44 Pass 802.11ac-VHT40 MCS0 62 5310 40.20 36.47 Pass 802.11ac-VHT40 MCS0 102 5510 45.45 36.45 Pass 802.11ac-VHT40 MCS0 118 5590 40.46 36.49 Pass 802.11ac-VHT40 MCS0 134 5670 51.07 36.58 Pass 802.11ac-VHT40 MCS0 142 5710 40.39 36.54 Pass 802.11ac-VHT80 MCS0 58 5290 82.06 75.96 Pass 802.11ac-VHT80 MCS0 106 5530 83.31 75.82 Pass 802.11ac-VHT80 MCS0 122 5610 81.70 75.96 Pass 802.11ac-VHT80 MCS0 138 5690 81.88 75.99 Pass FCC ID: Q9DAPINH203 Page Number: 25 of 406

Report No.: 1703TW0106-U6 802.11a 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) Channel 100 (5500MHz) Channel 120 (5600MHz) Channel 140 (5700MHz) FCC ID: Q9DAPINH203 Page Number: 26 of 406

Report No.: 1703TW0106-U6 802.11a 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 144 (5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPINH203 Page Number: 27 of 406

Report No.: 1703TW0106-U6 802.11n-HT20 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) Channel 100 (5500MHz) Channel 120 (5600MHz) Channel 140 (5700MHz) FCC ID: Q9DAPINH203 Page Number: 28 of 406

Report No.: 1703TW0106-U6 802.11n-HT20 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 144 (5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPINH203 Page Number: 29 of 406

Report No.: 1703TW0106-U6 802.11n-HT40 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 54 (5270MHz) Channel 62 (5310MHz) Channel 102 (5510MHz) Channel 118 (5590MHz) Channel 134 (5670MHz) Channel 142 (5710MHz) FCC ID: Q9DAPINH203 Page Number: 30 of 406

Report No.: 1703TW0106-U6 802.11n-HT40 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 151 (5755MHz) Channel 159 (5795MHz) FCC ID: Q9DAPINH203 Page Number: 31 of 406

Report No.: 1703TW0106-U6 802.11ac-VHT20 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) Channel 100 (5500MHz) Channel 120 (5600MHz) Channel 140 (5700MHz) FCC ID: Q9DAPINH203 Page Number: 32 of 406

Report No.: 1703TW0106-U6 802.11ac-VHT20 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 144 (5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) FCC ID: Q9DAPINH203 Page Number: 33 of 406

Report No.: 1703TW0106-U6 802.11ac-VHT40 26dB Bandwidth & 99% Bandwidth - Ant 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 54 (5270MHz) Channel 62 (5310MHz) Channel 102 (5510MHz) Channel 118 (5590MHz) FCC ID: Q9DAPINH203 Page Number: 34 of 406


Document Created: 2017-07-03 18:10:21
Document Modified: 2017-07-03 18:10:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC