Test Report DTS BLE

FCC ID: Q95ER22

Test Report

Download: PDF
FCCID_4091242

DATE: 13 November 2018 I.T.L. (PRODUCT TESTING) LTD. FCC/IC Radio Test Report for Cardo Systems Ltd. Equipment under test: Bluetooth Communication System for Motorcycles Original: scala rider FREECOM 4 New: FREECOM 4+ Tested by: _____________________________ M. Zohar Approved by: _____________________________ D. Shidlowsky This report must not be reproduced, except in full, without the written permission of I.T.L. (Product Testing) Ltd. This report relates only to items tested. Test Report E191450.00 Cardo Systems Ltd. Page 1 of 29 FCC ACC M Ver 1.2 28 February 2011

Measurement/Technical Report for Cardo Systems Ltd. Bluetooth Communication System for Motorcycles Original: scala rider FREECOM 4 New: FREECOM 4+ FCC ID: Q95ER22 IC: 4668A-ER22 This report concerns: Original Grant: Class I Change: Class II Change: X Equipment type: FCC: DTS Digital Transmission System IC: Spread Spectrum Digital Device (2400-2483.5) Limits used: 47CFR15 Section 15.247 RSS 247, Issue 2, February 2017, Section 5 RSS-Gen, Issue 5, April 2018 Measurement procedures used are FCC Public Notice DA-00-705 and ANSI C63.10: 2013. Application for Certification Applicant for this device: prepared by: (different from "prepared by") R. Pinchuck Amit Davidson ITL (Product Testing) Ltd. Cardo Systems Ltd. 1 Bat Sheva Street 811 E. Plano Parkway, Suite 110A Lod 7116002 Plano, Texas, USA, 75074 Israel Tel: +1 (214) 396-1196 e-mail Rpinchuck@itlglobal.org Fax: +1 (214) 276-7844 Email: amitd@cardosystems.com Test Report E191450.00 Cardo Systems Ltd. Page 2 of 29 FCC ACC M Ver 1.2 28 February 2011

TABLE OF CONTENTS 1. GENERAL INFORMATION ------------------------------------------------------------------------------- 4 1.1 Administrative Information ................................................................................. 4 1.2 List of Accreditations ......................................................................................... 5 1.3 Product Description ........................................................................................... 6 1.4 Test Methodology .............................................................................................. 6 1.5 Test Facility ....................................................................................................... 6 1.6 Measurement Uncertainty ................................................................................. 6 2. SYSTEM TEST CONFIGURATION --------------------------------------------------------------------- 7 2.1 Justification ........................................................................................................ 7 2.2 EUT Exercise Software ..................................................................................... 8 2.3 Special Accessories .......................................................................................... 8 2.4 Equipment Modifications ................................................................................... 8 2.5 Configuration of Tested System ........................................................................ 8 3. CONDUCTED & RADIATED MEASUREMENT TEST SET-UP PHOTOS ------------------10 4. OCCUPIED BANDWIDTH -------------------------------------------------------------------------------12 4.1 Test Specification ............................................................................................ 12 4.2 Test Procedure ................................................................................................ 12 4.3 Test Limit ......................................................................................................... 12 4.4 Test Results..................................................................................................... 12 4.5 Test Equipment Used, Occupied Bandwidth................................................... 14 5. PEAK OUTPUT POWER ---------------------------------------------------------------------------------15 5.1 Test Specification ............................................................................................ 15 5.2 Test Procedure ................................................................................................ 15 5.3 Test Limit ......................................................................................................... 15 5.4 Test Results..................................................................................................... 15 5.5 Test Equipment Used, Radiated Maximum Power Output ............................. 16 6. SPURIOUS RADIATED EMISSIONS -----------------------------------------------------------------17 6.1 Test Specification ............................................................................................ 17 6.2 Test Procedure ................................................................................................ 17 6.3 Test Limit ......................................................................................................... 18 6.4 Test Results..................................................................................................... 18 6.5 Test Equipment Used, Spurious Radiated Emissions ................................... 20 7. R.F EXPOSURE/SAFETY --------------------------------------------------------------------------------21 8. APPENDIX A - CORRECTION FACTORS ----------------------------------------------------------23 8.1 Correction factors for RF OATS Cable 35m ITL #1879 ................................. 23 8.2 Correction factor for RF CABLE for Semi Anechoic Chamber........................ 24 8.3 Correction factors for Active Loop Antenna .................................................... 25 8.4 Correction factors for biconical antenna – ITL # 1356 .................................... 26 8.5 Correction factors for log periodic antenna – ITL # 1349 ................................ 27 8.6 Correction factors for Double –Ridged Waveguide Horn ANTENNA............. 28 8.7 Correction factors for Horn Antenna .............................................................. 29 Test Report E191450.00 Cardo Systems Ltd. Page 3 of 29 FCC ACC M Ver 1.2 28 February 2011

1. General Information 1.1 Administrative Information Manufacturer: Cardo Systems Ltd. Manufacturer's Address: 811 E. Plano Parkway Suite 110A Plano, Texas USA, 75074 Tel: +1 (214) 396-1196 Fax: +1 (214) 276-7844 Manufacturer's Representative: Amit Davidson Equipment Under Test (E.U.T): Bluetooth Communication System for Motorcycles PMN: Original: scala rider FREECOM 4 New: FREECOM 4+ Equipment Serial No.: Not designated HVIN: 1 Date of Receipt of E.U.T: July 26, 2018 Start of Test: July 26, 2018 End of Test: October 7, 2018 Test Laboratory Location: I.T.L (Product Testing) Ltd. 1 Batsheva St., Lod ISRAEL 7120101 Test Specifications: 47CFR15 Section 15.247 RSS 247, Issue 2, February 2017, Section 5 RSS-Gen, Issue 5, April 2018 Test Report E191450.00 Cardo Systems Ltd. Page 4 of 29 FCC ACC M Ver 1.2 28 February 2011

1.2 List of Accreditations The EMC laboratory of I.T.L. is accredited by the following bodies: 1. The American Association for Laboratory Accreditation (A2LA) (U.S.A.), Certificate No. 1152.01. 2. The Federal Communications Commission (FCC) (U.S.A.), FCC Designation No. IL1005. 3. The Israel Ministry of the Environment (Israel), Registration No. 1104/01. 4. Industry Canada (Canada), IC File No.: 46405-4025; Site Nos. IC 4025A-1, IC 4025A-2. I.T.L. Product Testing Ltd. is accredited by the American Association for Laboratory Accreditation (A2LA) and the results shown in this test report have been determined in accordance with I.T.L.'s terms of accreditation unless stated otherwise in the report. Test Report E191450.00 Cardo Systems Ltd. Page 5 of 29 FCC ACC M Ver 1.2 28 February 2011

1.3 Product Description This product is a Bluetooth communication system, Bluetooth intercom for motorbikes and FM Radio receiver. 1.4 Test Methodology Radiated testing was performed according to the procedures in FCC Public Notice DA 00-705 and ANSI C63.10: 2013. Radiated testing was performed at an antenna to EUT distance of 3 meters. 1.5 Test Facility Emissions tests were performed at I.T.L.’s testing facility in Lod, Israel. I.T.L.’s EMC Laboratory is accredited by A2LA, certificate No. 1152.01 and its FCC Designation Number is IL1005. 1.6 Measurement Uncertainty Conducted Emission Conducted Emission (CISPR 11, EN 55011, CISPR 22, EN 55022, ANSI C63.4) 0.15 – 30 MHz: Expanded Uncertainty (95% Confidence, K=2): ± 3.6 dB Radiated Emission Radiated Emission (CISPR 11, EN 55011, CISPR 22, EN 55022, ANSI C63.4) for open site: 30-1000MHz: Expanded Uncertainty (95% Confidence, K=2): ± 4.96 dB 1 GHz to 6 GHz Expanded Uncertainty (95% Confidence, K=2): ±5.19 dB >6 GHz Expanded Uncertainty (95% Confidence, K=2): ±5.51 dB Test Report E191450.00 Cardo Systems Ltd. Page 6 of 29 FCC ACC M Ver 1.2 28 February 2011

2. System Test Configuration 2.1 Justification 1. The E.U.T. was originally FCC certified on 02/14/2017 under FCC ID: Q95ER22 and IC certified on 1/31/2017 under IC: 4668A-ER22. 2. Currently, C2PC changes were made to the original E.U.T. which will now be known as the FREECOM 4+. See customer’s declaration of changes on page 9. 3. A C2PC is requested based on those changes. The following tests were performed: occupied bandwidth, peak output power and spurious radiated emissions. 4. The E.U.T. met the requirements of a C2PC. 5. The E.U.T contains an IEEE 802.15.1 standard (BLE) transceiver. 6. The unit was evaluated while transmitting at the low channel (2402MHz), the mid channel (2440MHz) and the high channel (2480MHz). 7. Conducted emission method was performed with EUT connected to spectrum analyzer via 30dB attenuator. 8. Final radiated emission test for spurious emission for the new model was performed after exploratory emission testing that was performed in 3 orthogonal polarities to determine the “worst case” radiation. 9. According to the following results the worst case axis was the Y axis for all channels. Test Report E191450.00 Cardo Systems Ltd. Page 7 of 29 FCC ACC M Ver 1.2 28 February 2011

2nd 3rd Frequency Orientation Harmonic Harmonic (MHz) (dBuV/m) (dBuV/m) 2402.0 50.5 59.0 X axis 2440.0 49.9 58.1 2480.0 52.7 53.9 2402.0 52.4 62.9 Y axis 2440.0 51.5 63.1 2480.0 52.9 57.9 2402.0 47.0 59.1 Z axis 2440.0 50.1 60.9 2480.0 50.0 51.6 Figure 1. Screening Results 2.2 EUT Exercise Software No special exercise software was used. 2.3 Special Accessories No special accessories were needed in order to achieve compliance. 2.4 Equipment Modifications No modifications were needed in order to achieve compliance. 2.5 Configuration of Tested System E.U.T Figure 2. Configuration of Tested System, Radiated 30dB Spectrum EUT Attenuator Analyzer Figure 3. Configuration of Tested System, Conducted Test Report E191450.00 Cardo Systems Ltd. Page 8 of 29 FCC ACC M Ver 1.2 28 February 2011

Test Report E191450.00 Cardo Systems Ltd. Page 9 of 29 FCC ACC M Ver 1.2 28 February 2011

3. Conducted & Radiated Measurement Test Set-Up Photos Figure 4. Conducted Emission Test Figure 5. Radiated Emission Test, 30-200MHz Test Report E191450.00 Cardo Systems Ltd. Page 10 of 29 FCC ACC M Ver 1.2 28 February 2011

Figure 6. Radiated Emission Test, 200-1000MHz Figure 7. Radiated Emission Test, 1-18GHz Test Report E191450.00 Cardo Systems Ltd. Page 11 of 29 FCC ACC M Ver 1.2 28 February 2011

4. Occupied Bandwidth 4.1 Test Specification F.C.C. Part 15, Subpart C: section 2.1048 RSS Gen, Issue 4, November 2014 4.2 Test Procedure (Temperature (22°C)/ Humidity (60%RH)) The E.U.T operation mode and test set-up are as described in Section 2 of this report. The E.U.T. antenna terminal was connected to the Spectrum Analyzer through an external attenuator and an appropriate coaxial cable. The spectrum analyzer was set to the following parameters: Span = ~ 1.5 to 5 times the OBW RBW = between 1% to 5% of the OBW Detector Function: Peak, Trace: Maximum Hold. 4.3 Test Limit N/A 4.4 Test Results Operation Bandwidth Unit type Modulation Frequency Reading (MHz) (kHz) 2402.0 1029.9 4+ BLE 2440.0 1029.9 2480.0 1029.9 Figure 8 Test Results JUDGEMENT: Passed For additional information see Figure 9 to Figure 11. Test Report E191450.00 Cardo Systems Ltd. Page 12 of 29 FCC ACC M Ver 1.2 28 February 2011

Figure 9. BLE, Low Figure 10. BLE, Mid Figure 11. BLE, High Test Report E191450.00 Cardo Systems Ltd. Page 13 of 29 FCC ACC M Ver 1.2 28 February 2011

4.5 Test Equipment Used, Occupied Bandwidth Instrument Manufacturer Model Serial No. Last Calibration Next Calibration Date Due Commscope 0623 WBC- October 1, 2017 RF Cable G020132- October 31, 2018 ORS 400 30dB Attenuator MCL BW-S30W5 533 October 1, 2017 October 31, 2018 Spectrum Rohde & FSL6 100194 February 19, 2018 February 19, 2019 Analyzer Schwarz RG214- RF Cable (OATS) EIM - August 13, 2018 August 31, 2019 11N(X2) Figure 12 Test Equipment Used Test Report E191450.00 Cardo Systems Ltd. Page 14 of 29 FCC ACC M Ver 1.2 28 February 2011

5. Peak Output Power 5.1 Test Specification F.C.C. Part 15, Subpart C: section 15.247(b)(1) RSS 247, Issue 2, Clause 5.4(2) 5.2 Test Procedure (Temperature (22°C)/ Humidity (60%RH)) The E.U.T operation mode and test set-up are as described in Section 2 of this report. The E.U.T. antenna terminal was connected to the Spectrum Analyzer through an external attenuator and an appropriate coaxial cable. 5.3 Test Limit The maximum peak conducted output power of the intentional radiator shall not exceed the following: For frequency hopping systems operating in the 2400-2483.5 MHz band employing at least 75 non-overlapping hopping channels: 1 watt. For all other frequency hopping systems in the 2400-2483.5 MHz band: 0.125 watts. (The limits above applies to antenna gain until 6dBi). 5.4 Test Results JUDGEMENT: Passed by 932.4 mW Unit Modulation Operation Power Power Limit Margin Frequency (Original/New) (MHz) (dBm) (mW) (mW) (mW) 2402.0 17.4 55.0 1000.0 -945.0 Original BLE 2440.0 18.3 67.6 1000.0 -932.4 2480.0 17.5 56.2 1000.0 -943.8 2402.0 16.9 49.0 1000.0 -951.0 New BLE 2440.0 18.0 63.1 1000.0 -936.9 2480.0 17.4 55.0 1000.0 -945.0 Figure 13 Radiated Power Output Test Results Test Report E191450.00 Cardo Systems Ltd. Page 15 of 29 FCC ACC M Ver 1.2 28 February 2011

5.5 Test Equipment Used, Radiated Maximum Power Output Instrument Manufacturer Model Serial No. Last Calibration Next Calibration Date Due RF Cable Huber Suner Sucofelex 27502/4PEA October 1, 2017 October 31, 2018 BW- 30dB Attenuator MCL 533 October 1, 2017 October 31, 2018 S30W5 Spectrum Rohde & FSL6 100194 February 19, 2018 February 19, 2019 Analyzer Schwarz Figure 14 Test Equipment Used Test Report E191450.00 Cardo Systems Ltd. Page 16 of 29 FCC ACC M Ver 1.2 28 February 2011

6. Spurious Radiated Emissions 6.1 Test Specification FCC, Part 15, Subpart C, Sections 247(d), 15.205, 15.209 RSS Gen, Issue 4, Section 8.10 6.2 Test Procedure (Temperature (22°C)/ Humidity (60%RH)) For measurements between 0.009MHz-30MHz: The E.U.T was tested inside the shielded room at a distance of 3 meters and the E.U.T was placed on a non-metallic table, 0.8 meters above the ground. The frequency range 0.009MHz-30MHz was scanned. The readings were maximized by the turntable azimuth between 0-360°, and the antenna polarization. The emissions were measured at a distance of 3 meters. For measurements between 30.0MHz-1.0GHz: A preliminary measurement to characterize the E.U.T was performed inside the shielded room at a distance of 3 meters, using peak detection mode and broadband antennas. The preliminary measurements produced a list of the highest emissions. The E.U.T was then transferred to the open site, and placed on a remote-controlled turntable. The E.U.T was placed on a non-metallic table, 0.8 meters above the ground. The frequency range 30.0MHz -1.0GHz was scanned and the list of the highest emissions was verified and updated accordingly. The readings were maximized by adjusting the antenna height between 1-4 meters, the turntable azimuth between 0-360°, and the antenna polarization. The emissions were measured at a distance of 3 meters. For measurements between 1.0GHz-25.0GHz: The E.U.T was tested inside the shielded room at a distance of 3 meters and the E.U.T was placed on a non-metallic table, 1.5 meters above the ground. The frequency range 1.0GHz -25.0GHz was scanned. The readings were maximized by the turntable azimuth between 0-360°, and the antenna polarization. The emissions were measured at a distance of 3 meters. The levels of the emissions within the frequency ranges of the restricted bands (Section 15.205 of FCC Part 15) were compared to the limits of the table in Section 15.209 (a), General Requirements. Test Report E191450.00 Cardo Systems Ltd. Page 17 of 29 FCC ACC M Ver 1.2 28 February 2011

6.3 Test Limit Radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). Frequency Field strength Measurement Field strength* Field strength* (MHz) (microvolts/meter) distance (meters) (dBµV/m) (dBµV/m)@3m 0.009-0.490 2400/F(kHz) 300 48.5-13.8 128.5-73.8 0.490-1.705 24000/F(kHz) 30 33.8-23.0 73.8-63.0 1.705-30.0 30 30 29.5 69.5 30-88 100 3 40.0 40.0 88-216 150 3 43.5 43.5 216-960 200 3 46.0 46.0 Above 960 500 3 54.0 54.0 *The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9-90 kHz, 110-490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. For average radiated emission measurements above 1000 MHz, there is also a limit corresponding to 20 dB above the indicated values in the table is specified when measuring with peak detector function. 6.4 Test Results JUDGEMENT: Passed The EUT met the requirements of the F.C.C. Part 15, Subpart C 209 and RSS Gen, Issue 4, Section 8.10 specification. For additional information see Figure 15. Test Report E191450.00 Cardo Systems Ltd. Page 18 of 29 FCC ACC M Ver 1.2 28 February 2011

Spurious Radiated Emission Specification: FCC, Part 15, Subpart C; Sections 15.209, 15.205, 15.247(d); RSS Gen, Issue 4, Section 8.10 Antenna Polarization: Horizontal/Vertical Frequency range: 9 kHz to 25.0 GHz Protocol type: BLE Detectors: Peak Operation Peak Peak Peak Unit Freq. Pol Frequency Reading Limit Margin (Original/New) (MHz) (MHz) (H/V) (dBµV/m) (dBµV/m) (dB) 4804.0 V 50.5 74.0 -23.5 4804.0 H 53.9 74.0 -20.1 2402.0 7206.0 V 51.3 74.0 -22.7 7206.0 H 63.4 74.0 -10.6 4880.0 V 50.5 74.0 -23.5 4880.0 H 52.9 74.0 -21.1 Original 2440.0 7320.0 V 50.6 74.0 -23.4 7320.0 H 60.7 74.0 -13.3 4960.0 V 52.2 74.0 -21.8 4960.0 H 53.5 74.0 -20.5 2480.0 7440.0 V 50.8 74.0 -23.2 7440.0 H 58.0 74.0 -16.0 4804.0 V 49.9 74.0 -24.1 4804.0 H 55.1 74.0 -18.9 2402.0 7206.0 V 50.1 74.0 -23.9 7206.0 H 62.7 74.0 -11.3 4880.0 V 51.8 74.0 -22.2 4880.0 H 55.0 74.0 -19.0 New (4+) 2440.0 7320.0 V 52.5 74.0 -21.5 7320.0 H 62.8 74.0 -11.2 4960.0 V 54.0 74.0 -20.0 4960.0 H 55.0 74.0 -19.0 2480.0 7440.0 V 51.0 74.0 -23.0 7440.0 H 60.7 74.0 -13.3 Figure 15. Radiated Emission Results - BLE Test Report E191450.00 Cardo Systems Ltd. Page 19 of 29 FCC ACC M Ver 1.2 28 February 2011

Margin refers to the test results obtained minus specified requirement; thus a positive number indicates failure, and a negative result indicates that the product passes the test. “Peak Amp” includes correction factor. * “Correction Factor” = Antenna Factor + Cable Loss- Low Noise Amplifier Gain 6.5 Test Equipment Used, Spurious Radiated Emissions Last Calibration Next Calibration Instrument Manufacturer Model Serial Number Date Due EMI Receiver R&S ESCI7 100724 February 19, 2018 February 19, 2019 Spectrum HP 8592L 3826A01204 February 19, 2018 February 19, 2019 Analyzer EMI Receiver HP 8542E 3906A00276 February 19, 2018 February 19, 2019 RF Filter 85420E 3705A00248 February 19, 2018 HP February 19, 2019 Section Horn Antenna ETS 3115 29845 May 31, 2018 May 31 2021 Horn Antenna ARA SWH-28 1007 December 13, 2017 December 13, 2020 Log Periodic EMCO 3146 9505-4081 May 31, 2018 May 31, 2019 Antenna Biconical Log EMCO 3110B 9912-3337 May 15, 2017 May 15, 2019 Antenna Active Loop EMCO 6502 9506-2950 October 19, 2017 October 31, 2018 Antenna Low Noise DBS LNA-DBS- 013 October 1, 2017 October 31, 2018 Amplifier MICROWAVE 0411N313 Low Noise Sophia Wireless LNA 28-B 232 October 1, 2017 October 31, 2018 Amplifier RF Cable Commscope ORS 0623 WBC-400 G020132- October 1, 2017 October 31, 2018 RF Cable August 13, 2018 August 31, 2019 EIM RG214-11N(X2) - (OATS) Semi Anechoic NCR ETS S81 SL 11643 NCR Civil Chamber Antenna Mast ETS 2070-2 9608-1497 NCR NCR Turntable ETS 2087 - NCR NCR Mast & Table ETS/EMCO 2090 9608-1456 NCR NCR Controller Figure 16 Test Equipment Used Test Report E191450.00 Cardo Systems Ltd. Page 20 of 29 FCC ACC M Ver 1.2 28 February 2011

7. R.F Exposure/Safety The typical placement of the E.U.T. is on a motorcycle helmet. The typical distance between the E.U.T. and the user is 4cm. See photos on following page. SAR Testing Exclusion Based on Section 4.3.1 and Appendix A of KDB447498 D01 V05 and RSS 102, Issue 5, Section 2.5.2 Requirements For FCC Section 4.3.1 and Appendix A of KDB447498 D01 V05 was used as the guidance as follows: Peak power output =18.0 dBm =63.1mW [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] *· [√f(GHz)] = 63.1/40 * 1.55=2.45 this value is less than 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. The SAR measurement is not necessary. For IC (a) For IC per Table 1 of RSS 102 Issue 5, SAR exemption based on IC limit of 173.0mW at a separation distance of 40mm= 4.0cm at 2450 MHz. EUT power transmission is 18.0dBm =63.1mW This is below the 173.0mW SAR exemption limits. See photos on following page. Test Report E191450.00 Cardo Systems Ltd. Page 21 of 29 FCC ACC M Ver 1.2 28 February 2011

Test Report E191450.00 Cardo Systems Ltd. Page 22 of 29 FCC ACC M Ver 1.2 28 February 2011

8. APPENDIX A - CORRECTION FACTORS 8.1 Correction factors for RF OATS Cable 35m ITL #1879 Frequency Cable loss (MHz) (dB) 30.0 1.1 50.0 1.1 100.0 1.7 150.0 2.1 200.0 2.5 250.0 2.7 300.0 2.9 350.0 3.1 400.0 3.5 450.0 3.7 500.0 3.9 550.0 4.0 600.0 4.2 650.0 4.4 700.0 4.9 750.0 5.0 800.0 5.0 850.0 4.9 900.0 5.0 950.0 5.1 1000.0 5.4 Test Report E191450.00 Cardo Systems Ltd. Page 23 of 29 FCC ACC M Ver 1.2 28 February 2011

8.2 Correction factor for RF CABLE for Semi Anechoic Chamber ITL # 1841 FREQ LOSS (MHz) (dB) 1000.0 1.5 2000.0 2.1 3000.0 2.7 4000.0 3.1 5000.0 3.5 6000.0 4.1 7000.0 4.6 8000.0 4.9 9000.0 5.7 10000.0 5.7 11000.0 6.1 12000.0 6.1 13000.0 6.2 14000.0 6.7 15000.0 7.4 16000.0 7.5 17000.0 7.9 18000.0 8.1 19000.0 8.8 20000.0 9.1 NOTES: 1. The cable is manufactured by Commscope 2. The cable type is 0623 WBC-400, serial # G020132 and 10m long Test Report E191450.00 Cardo Systems Ltd. Page 24 of 29 FCC ACC M Ver 1.2 28 February 2011

8.3 Correction factors for Active Loop Antenna Model 6502 S/N 9506-2950 ITL # 1075: f(MHz) MAF(dBs/m) AF(dB/m) 0.01 -33.1 18.4 0.02 -37.2 14.3 0.03 -38.2 13.3 0.05 -39.8 11.7 0.1 -40.1 11.4 0.2 -40.3 11.2 0.3 -40.3 11.2 0.5 -40.3 11.2 0.7 -40.3 11.2 1 -40.1 11.4 2 -40 11.5 3 -40 11.5 4 -40.1 11.4 5 -40.2 11.3 6 -40.4 11.1 7 -40.4 11.1 8 -40.4 11.1 9 -40.5 11 10 -40.5 11 20 -41.5 10 30 -43.5 8 Test Report E191450.00 Cardo Systems Ltd. Page 25 of 29 FCC ACC M Ver 1.2 28 February 2011

8.4 Correction factors for biconical antenna – ITL # 1356 Model: EMCO 3110B Serial No.:9912-3337 Frequency ITL 1356 AF [MHz] [dB/m] 30 13.00 35 10.89 40 10.59 45 10.63 50 10.12 60 9.26 70 7.74 80 6.63 90 8.23 100 11.12 120 13.16 140 13.07 160 14.80 180 16.95 200 17.17 Test Report E191450.00 Cardo Systems Ltd. Page 26 of 29 FCC ACC M Ver 1.2 28 February 2011

8.5 Correction factors for log periodic antenna – ITL # 1349 Model: EMCO 3146 Serial No.:9505-4081 Frequency ITL 1349 AF [MHz] [dB/m] 200 11.58 250 12.04 300 14.76 400 15.55 500 17.85 600 18.66 700 20.87 800 21.15 900 22.32 1000 24.22 Test Report E191450.00 Cardo Systems Ltd. Page 27 of 29 FCC ACC M Ver 1.2 28 February 2011

8.6 Correction factors for Double –Ridged Waveguide Horn ANTENNA Model: 3115 Serial number:29845 3 meter range; ITL # 1352 FREQUENCY AFE FREQUENCY AFE (GHz) (dB/m) (GHz) (dB/m) 0.75 25 9.5 38 1.0 23.5 10.0 38.5 1.5 26.0 10.5 38.5 2.0 29.0 11.0 38.5 2.5 27.5 11.5 38.5 3.0 30.0 12.0 38.0 3.5 31.5 12.5 38.5 4.0 32.5 13.0 40.0 4.5 32.5 13.5 41.0 5.0 33.0 14.0 40.0 5.5 35.0 14.5 39.0 6.0 36.5 15.0 38.0 6.5 36.5 15.5 37.5 7.0 37.5 16.0 37.5 7.5 37.5 16.5 39.0 8.0 37.5 17.0 40.0 8.5 38.0 17.5 42.0 9.0 37.5 18.0 42.5 Test Report E191450.00 Cardo Systems Ltd. Page 28 of 29 FCC ACC M Ver 1.2 28 February 2011

8.7 Correction factors for Horn Antenna Model: SWH-28 at 3 meter range. ITL #:1353 Test Report E191450.00 Cardo Systems Ltd. Page 29 of 29 FCC ACC M Ver 1.2 28 February 2011


Document Created: 2019-03-27 22:08:03
Document Modified: 2019-03-27 22:08:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC