11 SAR test report

FCC ID: PY7A3880016

RF Exposure Info

Download: PDF
FCCID_1086814

1 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File Report issued by Accredited SAR Laboratory for FCC ID: PY7A3880016 (W508) Date of test: January 21st to January 30th 2009 Laboratory: Sony Ericsson SAR Test Laboratory Sony Ericsson Mobile Communications AB Maplewood, Chineham Business Park Basingstoke, RG24 8YB, England Testing Engineer: Jon Kenny Jon.Kenny@sonyericsson.com +44 1256 77 48 91 Testing Approval: Peter Lindeborg peter.lindeborg@sonyericsson.com +46 10 802 43 68 Statement of Compliance Sony Ericsson Mobile Communications AB declares under its sole responsibility that the product Sony Ericsson Type AAD-3880016-BV; FCC ID PY7A3880016; IC 4170B-A3880016 to which this declaration relates, is in conformity with the appropriate RF exposure standards recommendations and guidelines. It also declares that the product was tested in accordance with the appropriate measurement standards, guidelines and recommended practices. Any deviations from these standards, guidelines and recommended practices are noted below: (None) This laboratory is accredited to ISO/IEC 17025 (SWEDAC accreditation no. 1847). Laboratories are accredited by the Swedish Board for Accreditation and Conformity Assessment (SWEDAC) under the terms of Swedish legislation. The accredited laboratory activities meet the requirements in SS-EN ISO/IEC 17025 (2005). This report may not be reproduced other than in full, except with the prior written approval of the issuing laboratory. The results and statements contained herein relate only to the items tested. The names of individuals involved may be mentioned only in connection with the statements or results from this report. Sony Ericsson encourages all feedback, both positive and negative, on this report. © Sony Ericsson Mobile Communication AB, 2008

2 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File Table of contents 1 INTRODUCTION .................................................................................................................................................................. 3 2 CUSTOMER DETAILS ........................................................................................................................................................ 3 3 DEVICE UNDER TEST........................................................................................................................................................ 3 3.1 ANTENNA DESCRIPTION................................................................................................................................................... 3 3.2 DEVICE DESCRIPTION ...................................................................................................................................................... 4 4 TEST EQUIPMENT .............................................................................................................................................................. 5 4.1 DOSIMETRIC SYSTEM ....................................................................................................................................................... 5 4.2 ADDITIONAL EQUIPMENT ................................................................................................................................................. 5 5 ELECTRICAL PARAMETERS ON THE TISSUE SIMULATING LIQUID .............................................................. 6 6 SYSTEM ACCURACY VERIFICATION.......................................................................................................................... 7 7 SAR MEASUREMENT UNCERTAINTY ......................................................................................................................... 8 8 TEST RESULTS .................................................................................................................................................................... 9 9 REFERENCES ..................................................................................................................................................................... 11 APPENDIX .................................................................................................................................................................................... 12 9.1 PHOTOGRAPHS OF THE DEVICE UNDER TEST .................................................................................................................. 12 9.2 DEVICE POSITION AT SAM TWIN PHANTOM ................................................................................................................. 13 9.3 ATTACHMENTS ............................................................................................................................................................... 14

3 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 1 Introduction In this test report, compliance of the Sony Ericsson FCC ID: PY7A3880016 (W508) portable telephone with RF safety guidelines is demonstrated. The applicable RF safety guidelines and the SAR measurement specifications used for the test are described in the SAR Measurement Specifications of Wireless Handsets [1]. 2 Customer details Company Name: Sony Ericsson Mobile Communications AB Address: 2/F China Digital Kingdom Building, No.1 North, Beijing, 100102, China Contact Name: Roy Zhou 3 Device Under Test 3.1 Antenna Description Type Internal antenna Location Bottom of phone Main and BT 12.5mm antennas distance Dimensions Max length 46 mm Max width 14 mm Configuration Monopole

4 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 3.2 Device Description Device model AAD-3880016-BV Market name W508 Serial number (EUT #) BX900GKJ0S (#14448) Mode GSM 850 GSM 1900 Crest factor 8.3 8.3 Multiple access scheme TDMA TDMA Channel No. 128 190 251 512 661 885 1 Measured Power Level [dBm] 32.8 32.9 32.8 30.9 30.9 30.9 (#13877) Product Maximum power Level 1 33.0 33.0 33.0 31.0 31.0 31.0 [dBm] Data mode GPRS GPRS Crest factor 4.15 4.15 1 Measured Power Level [dBm] 29.9 29.9 29.9 28.0 27.8 27.9 (#13877) Product Maximum power Level 1 30.0 30.0 30.0 28.0 28.0 28.0 [dBm] Data mode EDGE EDGE Crest factor 4.15 4.15 1 Measured Power Level [dBm] 27.3 27.2 27.3 26.5 26.4 26.3 (#13877) Product Maximum power Level 1 27.5 27.5 27.5 26.5 26.5 26.5 [dBm] Transmitting frequency range 824.0 - 849.0 1850.0 - 1910.0 [MHz] GPRS Multislot class 10 EDGE class 10 GPRS Capability class B BT class and conducted power Class 1, 4.5 dBm Prototype or production unit Preproduction Hardware Version AP2.1 Software version R1DA017 Device category Portable RF exposure environment General population / uncontrolled

5 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 4 Test equipment 4.1 Dosimetric system SAR measurements were made using the DASY4 professional system (software version 4.7, Build 55) with SAM twin phantom, manufactured by Schmid & Partner Engineering AG (SPEAG). The list of calibrated equipment is given below. Description Serial Number Due Date DASY4 DAE3 448 2009-11 E-field probe ET3DV6 1610 2009-11 Dipole Validation Kit, D835V2 442 2009-12 Dipole Validation Kit, D1900V2 539 2009-12 4.2 Additional equipment Description Inventory Number Due Date Signal generator R&S SMY 02 3.094 2009-04 Directional coupler HP778D 15.233 None Power meter R&S NRVD 4.073 2009-04 Power sensor R&S NRV-Z5 4.074 2009-04 Power sensor R&S NRV-Z5 4.076 2009-04 Network analyzer Agilent 8719D 2.022 2009-04 Dielectric probe kit HP8507C 14.046 Self Cal R&S CMU200 20011270 2009-04

6 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 5 Electrical parameters on the tissue simulating liquid Prior to conducting SAR measurements, the relative permittivity, εr, and the conductivity σ, of the tissue simulating liquids were measured with the dielectric probe kit. These values are shown in the table below. The mass density, ρ, entered into the DASY4 software is also given. Recommended limits for permittivity εr, conductivity σ and mass density ρ are also shown. f Tissue Dielectric Parameters Density Measured / Recommended [MHz] type εr σ [S/m] ρ [g/cm³] Measured, 2009-01-28 40.29 0.86 1.00 835 Head Recommended 41.5 0.90 1.00 Measured, 2009-01-28 53.19 0.97 1.00 835 Body Recommended 55.2 0.97 1.00 Measured, 2009-01-21 38.02 1.47 1.00 1900 Head Recommended 40.0 1.40 1.00 Measured, 2009-01-29 50.66 1.54 1.00 1900 Body Recommended 53.3 1.52 1.00

7 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 6 System accuracy verification A system accuracy verification of the DASY4 was performed using the dipole validation kit listed in section 3.1. The system verification test was conducted on the same day as the measurement of the DUT. The ambient humidity and temperature of test facility were kept between the range 30-70% and 20.0-25.0 °C respectively. RF noise had been measured in liquid when all RF equipment in lab was switched off. Measured value was 0.0002 mW/g in 1g mass. Dielectric f Tissue SAR [W/kg] Density Liquid Measured / Reference Parameters [MHz] type 1g T[°C] εr σ [S/m] ρ [g/cm³] Measured, 2009-01-28 9.84 40.29 0.86 1.00 21.9 835 Head Reference 9.34 41.5 0.90 1.00 22.0 Measured, 2009-01-28 10.16 53.19 0.97 1.00 22.6 835 Body Reference 9.85 55.2 0.97 1.00 22.0 Measured, 2009-01-21 38.88 38.02 1.47 1.00 21.5 1900 Head Reference 41.3 40.0 1.40 1.00 22.0 Measured, 2009-01-29 40.4 50.66 1.54 1.00 21.6 1900 Body Reference 41.3 53.3 1.52 1.00 22.0

8 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 7 SAR measurement uncertainty SAR measurement uncertainty evaluation for Sony Ericsson PY7A3880016 (W508) phone According to IEEE 1528 Uncer. Prob Uncertainty Component Div. Ci 1g mass (%) Dist. Measurement System Probe Calibration ±5.9 N 1 1 ±5.9 Axial Isotropy ±4.7 R √3 0.7 ±1.9 Spherical Isotropy ±9.6 R √3 0.7 ±3.9 Boundary effect ±1.0 R √3 1 ±0.6 Probe linearity ±4.7 R √3 1 ±2.7 Detection limit ±1.0 R √3 1 ±0.6 Readout electronics ±0.3 N 1 1 ±0.3 Response time ±0.8 R √3 1 ±0.5 Integration time ±2.6 R √3 1 ±1.5 RF Ambient Conditions ±3.0 R √3 1 ±1.7 Mech. Constraints of robot ±0.4 R √3 1 ±0.2 Probe positioning ±2.9 R √3 1 ±1.7 Extrap, interpolation and integration ±1.0 R √3 1 ±0.6 Measurement System Uncertainty ±8.4 Test Sample Related Device positioning ±3.5 N 1 1 ±3.5 Device holder uncertainty ±3.5 N 1 1 ±3.5 Power drift ±5.0 R √3 1 ±2.9 Test Sample Related Uncertainty ±5.5 Phantom and Tissue Parameters Phantom uncertainty ±4.0 R √3 1 ±2.3 Liquid conductivity (measured) ±2.5 R 1 0.64 ±1.6 Liquid conductivity (target) ±5.0 R √3 0.64 ±1.8 Liquid Permittivity (measured) ±2.5 R 1 0.6 ±1.5 Liquid Permittivity (target) ±5.0 R √3 0.6 ±1.7 Phantom and Tissue Parameters ±4.1 Uncertainty Combined standard uncertainty ±10.8 Extended standard uncertainty (k=2) ±21.6

9 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 8 Test results The ambient humidity and temperature of test facility were kept between the range 30-70% and 20.0-25.0 °C respectively. A base station simulator was used to control the device during the SAR measurement. The DUT was supplied with a fully charged battery for each measurement. For head measurement, the DUT was tested with the flip open on the right-hand side, and the left-hand side of the phantom in two phone positions, cheek (touch) and tilt (cheek + 15°). The DUT was tested at the lowest, middle and highest frequencies in the transmission band. The measured 1-gram averaged SAR values of the DUT towards the head are provided in Table 1. For body measurement the DUT was tested with the flip in the closed position with the back (antenna) and front(display) towards the phantom flat section with 15 mm distance in both speech and data mode. For all modes, the device was tested at the lowest, middle and highest frequencies in the transmission band. For portable hands free (PHF) usage the Sony Ericsson head set HPB-60 was connected to the DUT. The measured 1-gram averaged SAR values of the DUT towards the body are provided in Table 2. Measured Measured SAR [W/kg] 1 Liquid Band Channel output power Position Left-hand Right-hand T [°C] [dBm] 1g mass 1g mass Cheek 23.9 0.53 0.63 128 32.8 Tilt 23.9 - - GSM Cheek 23.9 0.58 0.66 190 32.9 850 Tilt 23.9 0.40 0.39 Cheek 23.9 0.75 0.74 251 32.8 Tilt 23.9 - - Cheek 22.7 0.59 0.51 512 30.9 Tilt 22.7 - - GSM Cheek 22.7 0.60 0.52 661 30.9 1900 Tilt 22.7 0.22 0.29 Cheek 22.7 0.64 0.56 810 30.9 Tilt 22.7 - - Table 1: SAR measurement result for Sony Ericsson PY7A3880016 telephone at highest possible output power. Measured towards the head. 1 Measured output values were provided by the customer.

10 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File Measured output Measured 1 Liquid Band Channel power Position / Mode SAR [W/kg] T [°C] [dBm] 1g mass 32.8 Back / CS 22.6 0.69 128 29.9 Back / GPRS 22.6 0.61 32.9 Back / CS 22.6 0.64 190 29.9 Back / GPRS 22.6 0.73 GSM 850 32.8 Back / CS 22.6 0.53 32.8 Back / PHF 22.6 0.51 251 29.9 Back / GPRS 22.6 0.81 27.3 Back / EGPRS 22.6 0.44 29.9 Front / GPRS 22.6 0.43 30.9 Back / CS 24.7 0.65 512 28.0 Back / GPRS 24.7 0.60 30.9 Back / CS 24.7 0.71 661 27.8 Back / GPRS 24.7 0.65 GSM 1900 30.9 Back / CS 24.7 0.81 30.9 Back / PHF 24.7 0.47 810 27.9 Back / GPRS 24.7 0.75 26.3 Back / EGPRS 24.7 0.46 27.9 Front / GPRS 24.7 0.25 Table 2: SAR measurement result for Sony Ericsson PY7A3880016 telephone at highest possible output power. Measured towards the body. 1 Measured output values were provided by the customer.

11 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 9 References [1] R.Plicanic. “SAR Measurement Specification of Wireless Handsets”. Sony Ericsson SAR Test Laboratory internal document GUG/N 03:141 [2] FCC. “Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields: Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radio Frequency Emissions.” Supplement C (Edition 01-01) to OET Bulletin 65 (Edition 97- 01). [3] IEEE. “Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques.” Std 1528-2003. June. 2003. [4] IEC 62209-1. "Procedure to measure the Specific Absorption Rate (SAR) for hand-held mobile wireless devices in the frequency range of 300 MHz to 3 GHz". February 2005. [5] FCC KDB648474. "SAR Evaluation Consideration for HANDSETS with Multiple Transmitters and Antenna", April 2008.

12 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File Appendix 9.1 Photographs of the device under test Front & Back Open Sides Open Front & Back Closed Top & Bottom Closed

13 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File 9.2 Device position at SAM Twin Phantom DUT position towards the head Flip Open: Cheek (touch) position DUT position towards the head Flip Open: Tilt (touch + 15°) position

14 (14) Company Internal REPORT Prepared (also subject responsible if other) No. BA/SEMC/CCDAU Jon Kenny CCDA09: . Approved Checked Date Rev Reference LD/SEMC/CCDALEC Peter Lindeborg PL 090105 A File DUT position towards the body with Flip Closed and 15 mm distance 9.3 Attachments • System validation • Measurement plots for head and body position • Probe calibration • Dipole calibration


Document Created: 2009-03-27 16:48:03
Document Modified: 2009-03-27 16:48:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC