User Manual rev 4.pdf

FCC ID: PY317200381

Users Manual

Download: PDF
FCCID_3473761

                                   Quick Start Guide
                                              Model: NM8207




                                             Date: Jun, 27 2017
                                                  Rev 0.5




NETGEAR, INC.                                                     1
350 East Plumeria Drive San Jose, CA 95134


                                               Table of Contents
1     Revision History ............................................................................................................ 3
2     Setup/connect the device for testing. .......................................................................... 4
2.1   Install USB driver........................................................................................................... 4
2.2   Adjust jumpers on carrier board. ................................................................................. 4
2.3   Insert Nano SIM card into NM8207 module. ................................................................ 4
2.4   Connect NM8208 module with carrier board ............................................................... 4
2.5   Connect antenna cable with NM8207 module. ............................................................ 5
2.6   Connect carrier board and PC via USB cable. ............................................................ 5
3 Create data call connection .......................................................................................... 6
4 Execute AT command ................................................................................................... 8
4.1 Connect to NMEA port of module................................................................................. 8
5 Connect to QPST ........................................................................................................... 8
5.1 Add Diagnostics port .................................................................................................... 8
5.2 Add port to QPST Software Download ........................................................................ 9




NETGEAR, INC.                                                                                                                      2
350 East Plumeria Drive San Jose, CA 95134


1 Revision History

 0.1        2017/06/09       Initial version                                                  Woody Cheng
 0.2        2017/06/13       Changed model name to NM8207.                                    Woody Cheng
 0.3        2017/06/21        Add module and Dev kit installation guide on section 2.3 &2.4   GuanYu Jiang
 0.4        2017/06/27       Added section 3, “Create data call connection”.                  Woody Cheng
 0.5        2017/06/27       Updated the screenshot of the section 3 step7.                   Woody Cheng




NETGEAR, INC.                                                                                            3
350 East Plumeria Drive San Jose, CA 95134


2 Setup/connect the device for testing.
   2.1     Install USB driver.
   2.2     Adjust jumpers on carrier board.




   2.3 Insert Nano SIM card into NM8207 module.




    2.4 Connect NM8208 module with carrier board
A particular attention must be paid, please make sure the board to board connectors are perfect
aligned before pushing down the NM8207 module toward the carrier board.




    Caution: An inappropriate installation will break the board to board connectors permanently.


NETGEAR, INC.                                                                                      4
350 East Plumeria Drive San Jose, CA 95134


   2.5 Connect antenna cable with NM8207 module.




   2.6 Connect carrier board and PC via USB cable.




NETGEAR, INC.                                        5
350 East Plumeria Drive San Jose, CA 95134


3 Create data call connection
     Please follow the steps below to create data call connection.
     Step1: Insert SIM card into module.
     Step2: Connect PC and module via USB cable. And run “adb shell” on PC side in advance.
     Step3: Use putty to connect module.




     Step4: Execute the following commands to setup APN and launch connection manager.
          / # wnc-tools at_cmd AT+CGDCONT=1,\"IP\",\"internet\",\"\",0,0
          / # wnc-tools at_cmd "at+cgdcont?"
           / # /etc/init.d/start_QCMAP_ConnectionManager_le start
           / # QCMAP_CLI




NETGEAR, INC.                                                                                 6
350 East Plumeria Drive San Jose, CA 95134


     Step5: Select 30 to setup Mobile AP and then select 1 to enable it.




     Step6: Select 32 to connect Backhaul and set call type to IPv4.




     If the module connected to network successfully, “IPV4 WWAN Connected” message would show
     on the putty.




     Step7: Keep the original putty window, and then use putty to new another adb session to check
     the connection.




NETGEAR, INC.                                                                                        7
350 East Plumeria Drive San Jose, CA 95134


4 Execute AT command
   4.1 Connect to NMEA port of module.
         After the NMEA port was shown on device manager.
         You can connect to it via Tara Term tool. (or putty)
         Then you can use it to send AT command to module.




5 Connect to QPST
   5.1     Add Diagnostics port
           After the Diagnostics port was shown on device manager. Then you can use “QPST
           Configuration” tool to add Diagnostics port. Please follow the steps on the screenshot to add
           port.




NETGEAR, INC.                                                                                          8
350 East Plumeria Drive San Jose, CA 95134


  5.2    Add port to QPST Software Download
Add Diagnostics port to “QPST Software Download”, then you can start to use it to do QPST functions.




NETGEAR, INC.                                                                                          9
350 East Plumeria Drive San Jose, CA 95134


It powered by DC 3.3V (normal voltage), rating for lowest voltage is 2.97V and highest voltage is 3.63V



Test Antenna spec.
  Ant.        Gain(dBi)               Frequency range    Antenna   Connecter Type
         Including cable loss          (MHz to MHz)        Type     (External only)


ANT1             3.4            824 to 849 MHz          PIFA       I-PEX MHF IV
                 4.39           880 to 915 MHz
ANT2             2.62           1850 to 1915 MHz        PIFA       I-PEX MHF IV
                 4.25           1710 to 1785 MHz
                 3.82           1920 to 1980 MHz




NETGEAR, INC.                                                                                             10
350 East Plumeria Drive San Jose, CA 95134


                Federal Communication Commission Interference Statement

        This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
        conditions: (1) This device may not cause harmful interference, and (2) this device must accept
        any interference received, including interference that may cause undesired operation.

        This equipment has been tested and found to comply with the limits for a Class B digital device,
        pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
        protection against harmful interference in a residential installation. This equipment generates,
        uses and can radiate radio frequency energy and, if not installed and used in accordance with
        the instructions, may cause harmful interference to radio communications. However, there is
        no guarantee that interference will not occur in a particular installation. If this equipment
        does cause harmful interference to radio or television reception, which can be determined by
        turning the equipment off and on, the user is encouraged to try to correct the interference by
        one of the following measures:


        - Reorient or relocate the receiving antenna.
        - Increase the separation between the equipment and receiver.
        - Connect the equipment into an outlet on a circuit different from that
          to which the receiver is connected.
        - Consult the dealer or an experienced radio/TV technician for help.

        FCC Caution: Any changes or modifications not expressly approved by the party responsible for
        compliance could void the user's authority to operate this equipment.


        This transmitter must not be co-located or operating in conjunction with any other antenna or
        transmitter.


        Radiation Exposure Statement:
       This
        Theequipment   complies
             product comply  with with  FCC /portable
                                   the FCC     ISED radiation  exposure
                                                       RF exposure    limitlimits set forth
                                                                             set forth      for uncontrolled
                                                                                        for an  an
       uncontrolled  environment.    This equipment   should  be  installed  and   operated
        environment and are safe for intended operation as described in this manual.           with
       minimum distance 20cm between the radiator & your body.
        The further RF exposure reduction can be achieved if the product can be kept as far as possible
        from the user body or set the device to lower output power if such function is available.




NETGEAR, INC.                                                                                            11
350 East Plumeria Drive San Jose, CA 95134


     This device is intended only for OEM integrators under the following conditions:


        1) The antenna must be installed such that 20 cm is maintained between the
           antenna and users.
        2) The transmitter module may not be co-located with any other transmitter or
           antenna.


        As long as 2 conditions above are met, further transmitter test will not be required.
        However, the OEM integrator is still responsible for testing their end-product for
        any additional compliance requirements required with this module installed


        IMPORTANT NOTE: In the event that these conditions can not be met (for
        example certain laptop configurations or co-location with another transmitter),
        then the FCC authorization is no longer considered valid and the FCC ID can not
        be used on the final product. In these circumstances, the OEM integrator will be
        responsible for re-evaluating the end product (including the transmitter) and
        obtaining a separate FCC authorization.

        End Product Labeling
        This transmitter module is authorized only for use in device where the antenna
        may be installed such that 20 cm may be maintained between the antenna and
        users. The final end product must be labeled in a visible area with the following:
        “Contains FCC ID: PY317200381”. The grantee's FCC ID can be used only when
        all FCC compliance requirements are met.

        Manual Information To the End User
        The OEM integrator has to be aware not to provide information to the end user
        regarding how to install or remove this RF module in the user’s manual of the end
        product which integrates this module.
        The end user manual shall include all required regulatory information/warning as
        show in this manual.
                                               1.




NETGEAR, INC.                                                                             12
350 East Plumeria Drive San Jose, CA 95134


                                             Industry Canada statement:

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas
produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:
This equipment
This equipment complies
                complieswith ISED
                          with     radiation
                                ISED         exposure
                                      radiation       limitslimits
                                                exposure      set forth
                                                                    set for an for
                                                                         forth uncontrolled
                                                                                   an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
environment. This equipment
between the radiator         should be installed and operated with minimum distance 20cm
                      & your body.
between the radiator & your body.


Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module
device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.


Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
(Pour utilisation de dispositif module)

      1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée
entre l'antenne et les utilisateurs, et2) Le module émetteur peut ne pas être coïmplanté avec
un autre émetteur ou antenne.


NETGEAR, INC.                                                                                      13
350 East Plumeria Drive San Jose, CA 95134


Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
End Product Labeling This transmitter module is authorized only for use in device where the
antenna may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following: “Contains IC:
4054A-17200381”.

Plaque signalétique du produit final

Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre
l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec
l'inscription suivante: "Contient des IC: 4054A-17200381".




NETGEAR, INC.                                                                                 14
350 East Plumeria Drive San Jose, CA 95134



Document Created: 2017-07-20 18:48:34
Document Modified: 2017-07-20 18:48:34

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC