test report

FCC ID: PRDMU01

Test Report

Download: PDF
FCCID_1447457

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 FCC 47 CFR PART 15 Subpart C TEST REPORT For Wireless Mouse Model: G33 Trade Name: ACROX Issued to Acrox Technologies Co., Ltd. 4F., No.89, Minshan St., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Issued by Compliance Certification Services Inc. No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841,Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 http://www.ccsrf.com service@ccsrf.com Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NIST or any government agencies. The test results in the report only apply to the tested sample. Page 1 / 31 Rev/00

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Revision History Effect Rev. Issue Date Revisions Revised By Page 00 March 28, 2011 Initial Issue All Angel Hu Page 2 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION.................................................................................... 4 2. EUT DESCRIPTION ....................................................................................................... 5 3. TEST METHODOLOGY.................................................................................................. 6 3.1 EUT CONFIGURATION............................................................................................. 6 3.2 EUT EXERCISE......................................................................................................... 6 3.3 GENERAL TEST PROCEDURES.............................................................................. 6 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS .................................. 7 3.5 DESCRIPTION OF TEST MODES ............................................................................ 7 4. INSTRUMENT CALIBRATION ........................................................................................ 8 4.1 MEASURING INSTRUMENT CALIBRATION ............................................................ 8 4.2 MEASUREMENT EQUIPMENT USED ...................................................................... 8 4.3 MEASUREMENT UNCERTAINTY............................................................................. 8 5. FACILITIES AND ACCREDITATIONS ............................................................................ 9 5.1 FACILITIES................................................................................................................ 9 5.2 EQUIPMENT ............................................................................................................. 9 5.3 TABLE OF ACCREDITATIONS AND LISTINGS...................................................... 10 6. SETUP OF EQUIPMENT UNDER TEST....................................................................... 11 6.1 SETUP CONFIGURATION OF EUT ........................................................................ 11 6.2 SUPPORT EQUIPMENT ......................................................................................... 11 7. FCC PART 15.249 REQUIREMENTS........................................................................... 12 7.1 20DB BANDWIDTH.................................................................................................. 12 7.2 BAND EDGES MEASUREMENT............................................................................. 15 7.3 SPURIOUS EMISSION............................................................................................ 20 7.4 POWERLINE CONDUCTED EMISSIONS ............................................................... 27 8. APPENDIX 1 PHOTOGRAPHS OF TEST SETUP........................................................ 29 APPENDIX 1: PHOTOGRAPHS OF EUT............................................................................ 31 Page 3 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 1. TEST RESULT CERTIFICATION Acrox Technologies Co., Ltd. Applicant: 4F., No.89, Minshan St., Neihu Dist., Taipei City 114, Taiwan, R.O.C. Equipment Under Test: Wireless Mouse Trade Name: ACROX Model: G33 Date of Test: March 18 ~ 21, 2011 APPLICABLE STANDARDS STANDARD TEST RESULT FCC 47 CFR Part 15 Subpart C No non-compliance noted We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements emission limits of FCC Rules Part 15.207, 15.209 and 15.249. The test results of this report relate only to the tested sample identified in this report. Approved by: Reviewed by: Stan Lin Chieh Cheng Supervisor Engineer Page 4 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 2. EUT DESCRIPTION Product Wireless Mouse Model G33 Brand ACROX Model Discrepancy N/A EUT Power Rating 3VDC from Battery Operating Frequency 2403 ~ 2480MHz Range2400 Output Power 93.53dBuV/m Modulation Technique GFSK Number of Channels 78 Channels Antenna Gain -1.45dBi Antenna Designation PCB Antenna Remark: 1. The sample selected for test was production product and was provided by manufacturer. 2. This test report is intended for FCC ID: PRDMU01 to comply with Section 15.207, 15.209, 15.249 (FCC Part 15, Subpart C Rules.) 3. The Nano dongle (in external photographs) is a receiver only. Page 5 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 3. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.4 (2009) and FCC CFR 47 Part 2, Part 15.207, 15.209 and 15.249. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the Section 15.207, 15.209,15.249 under the FCC Rules Part 15 Subpart C. 3.3 GENERAL TEST PROCEDURES Conducted Emissions The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in Section 13.1.4.1 of ANSI C63.4 (2009) Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz using CISPR Quasi-peak and average detector modes. Radiated Emissions The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360 degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find out the maximum emissions, exploratory radiated emission measurements were made according to the requirements in Section 13.1.4.1 of ANSI C63.4 (2009). Page 6 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 3.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 - 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.52525 2655 - 2900 22.01 - 23.12 8.41425 - 8.41475 156.7 - 156.9 3260 - 3267 23.6 - 24.0 12.29 - 12.293 162.0125 - 167.17 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 167.72 - 173.2 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 240 - 285 3600 - 4400 (2) 13.36 - 13.41 322 - 335.4 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown in Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. 3.5 DESCRIPTION OF TEST MODES The EUT (model: G33) had been tested under operating condition. Test program used to control the EUT for staying in continuous transmitting mode was programmed. After verification, all tests were carried out with the worst case test modes as shown below except radiated spurious emission below 1GHz, which worst case was in normal link mode only. Channel Low (2403MHz), Channel Mid (2440MHz) and Channel High (2480MHz) were chosen for the final testing. The field strength of spurious emission was measured in the following position: EUT stand-up position (Z axis), lie-down position (X, Y axis). The worst emission was found in lie-down position (X axis) and the worst case was recorded. Page 7 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 4. INSTRUMENT CALIBRATION 4.1 MEASURING INSTRUMENT CALIBRATION The measuring equipment, which was utilized in performing the tests documented herein, has been calibrated in accordance with the manufacturer's recommendations for utilizing calibration equipment, which is traceable to recognized national standards. 4.2 MEASUREMENT EQUIPMENT USED Equipment Used for Emissions Measurement Remark: Each piece of equipment is scheduled for calibration once a year. 3M Semi Anechoic Chamber Name of Equipment Manufacturer Model Serial Number Calibration Due Spectrum Analyzer Agilent E4446A MY48250064 12/29/2011 Pre-Amplifier HP 8447D 2944A06530 01/02/2012 Pre-Amplifier HP 8449B 3008A01738 04/17/2011 EMI Test Receiver SCHAFFNER SCR 3501 430 01/18/2012 Loop Antenna EMCO 6502 2356 06/11/2011 Bilog Antenna SCHWAZBECK VULB9160 3084 10/07/2011 Horn Antenna EMCO 3115 00022250 05/09/2011 Turn Table CCS CC-T-1F N/A N.C.R Antenna Tower CCS CC-A-1F N/A N.C.R Controller CCS CC-C-1F N/A N.C.R Test S/W LabVIEW 6.1 (Wugu Chamber EMI Teat V1_4.5.3) 4.3 MEASUREMENT UNCERTAINTY Parameter Uncertainty Powerline Conducted Emission N/A 3M Semi Anechoic Chamber / 30MHz ~ 1GHz ±4.0474 3M Semi Anechoic Chamber / Above 1GHz ±3.8967 Remark: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Page 8 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 5. FACILITIES AND ACCREDITATIONS 5.1 FACILITIES All measurement facilities used to collect the measurement data are located at No. 199, Chunghsen Road, Hsintien City, Taipei Hsien, Taiwan, R.O.C. Tel: 886-2-2217-0894 / Fax: 886-2-2217-1029 No.11, Wugong 6th Rd., Wugu Industrial Park, Taipei Hsien 248, Taiwan Tel: 886-2-2299-9720 / Fax: 886-2-2298-4045 No.81-1, Lane 210, Bade 2nd Rd., Lujhu Township, Taoyuan County 33841,Taiwan, R.O.C. Tel: 886-3-324-0332 / Fax: 886-3-324-5235 The sites are constructed in conformance with the requirements of ANSI C63.7 (1992), ANSI C63.4 (2009) and CISPR Publication 22. 5.2 EQUIPMENT Radiated emissions are measured with one or more of the following types of linearly polarized antennas: tuned dipole, biconical, log periodic, bi-log, and/or ridged waveguide, horn. Spectrum analyzers with pre-selectors and quasi-peak detectors are used to perform radiated measurements. Conducted emissions are measured with Line Impedance Stabilization Networks and EMI Test Receivers. Calibrated wideband preamplifiers, coaxial cables, and coaxial attenuators are also used for making measurements. All receiving equipment conforms to CISPR Publication 16-1, “Radio Interference Measuring Apparatus and Measurement Methods.” Page 9 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 5.3 TABLE OF ACCREDITATIONS AND LISTINGS Country Agency Scope of Accreditation Logo CFR 47, FCC Part15/18, CISPR 22, EN 55022, ICES-003, AS/NZS CISPR 22, VCCI V-3, EN 55011, CISPR 11, IEC/EN 61000-4-2/3/4/5/6/8/11, EN 61000-6-1/2/3/4, USA A2LA EN 55024, CISPR 24, AS/NZS CISPR 24, AS/NZS 61000.6.2, EN 55014-1/-2, ETSI EN 300 386 v1.3.2/v1.3.3, IEC/EN 61000-3-2, AS/NZS 61000.3.2, IEC/EN 61000-3-3, AS/NZS 61000.3.3 FCC 3/10 meter Open Area Test Sites to perform USA MRA FCC Part 15/18 measurements TW1026 3/10 meter Open Area Test Sites and Japan VCCI conducted test sites to perform R-2882/2541/2798/725/1868 radiated/conducted measurements C-402/747/912 T-1930/1646 EN 55014-1, CISPR 14, CNS 13781-1, EN 55013, CISPR 13, CNS 13439, EN 55011, CISPR 11, CNS 13803, PLMN09, IS2045-0, LP0002 FCC Part 27/90, Part 15B/C/D/E, RSS-192/193/210/310 ETSI EN 300 328/ 300 220-1/ 300 220-2/ 301 Taiwan TAF 893/ 301 489-01/ 301 489-03/ 301 489-07 / 301 489-17/ 300 440-1/ 300 440-2 AS/NZS 4268, AS/NZS 4771 CISPR 22, EN 55022, CNS 13438, AS/NZS CISPR 22, VCCI, IEC/EN 61000-4-2/3/4/5/6/8/11, CNS 14676-2/3/4/5/6/8, CNS 14934-2/3, CNS 13783-1, CNS 13439, CNS 13803 SL2-IS-E-0014 / IN-E-0014 CNS 13438, CNS 13783-1, CNS 13439, Taiwan BSMI /A1-E-0014 /R1-E-0014 CNS 14115 /R2-E-0014 /L1-E-0014 Industry Canada RSS-Gen Issue 3 Canada IC 2324C-5 Note: No part of this report may be used to claim or imply product endorsement by A2LA, TAF or other government agency. Page 10 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 6. SETUP OF EQUIPMENT UNDER TEST 6.1 SETUP CONFIGURATION OF EUT See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. 6.2 SUPPORT EQUIPMENT No. Equipment Model No. Serial No. FCC ID Trade Name Data Cable Power Cord N/A **No any support equipment during the test. Remark: Grounding was established in accordance with the manufacturer’s requirements and conditions for the intended use. Page 11 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 7. FCC PART 15.249 REQUIREMENTS 7.1 20dB BANDWIDTH LIMIT None; for reporting purposes only. TEST CONFIGURATION EUT Spectrum Analyzer TEST PROCEDURE 1. Place the EUT on the table and set it in the transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as RBW=100kHz, VBW = 300kHz, Span = 3MHz, Sweep = auto. 4. Mark the peak frequency and 20dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. TEST RESULTS No non-compliance noted Page 12 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 TEST PLOT 20dB Bandwidth (CH Low) 20dB Bandwidth (CH Mid) Page 13 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 20dB Bandwidth (CH High) Page 14 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 7.2 BAND EDGES MEASUREMENT LIMIT 1. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (µV/m at 3-meter) (dBµV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 2. As shown in Section 15.35(b), for frequencies above 1000 MHz, the above field strength limits in paragraphs (a) and (b) of this section are based on average limits. However, the peak field strength of any emission shall not exceed the maximum permitted average limits specified above by more than 20 dB under any condition of modulation. For point-to-point operation under paragraph (b) of this section, the peak field strength shall not exceed 2500 millivolts/meter at 3 meters along the antenna azimuth. TEST CONFIGURATION Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above the ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emission. 4. Set the spectrum analyzer in the following setting in order to capture the lower and upper band-edges of the emission: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 5. Repeat the procedures until all the PEAK and AVERAGE versus POLARIZATION are measured. TEST RESULTS Refer to attach spectrum analyzer data chart. Page 15 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 TEST PLOT Band Edges (CH Low) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 16 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 17 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Band Edges (CH High) Detector mode: Peak Polarity: Vertical Detector mode: Average Polarity: Vertical Page 18 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Detector mode: Peak Polarity: Horizontal Detector mode: Average Polarity: Horizontal Page 19 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 7.3 SPURIOUS EMISSION LIMIT 1. In the section 15.249(a): Except as provided in paragraph (b) of this section, the field strength of emissions from intentional radiators operated within these frequency bands shall comply with the following: Field Strength of Fundamental Field Strength of Fundamental Frequency Harmonics Field Strength (MHz) (µV/m) (mV/m) 902-928 MHz 50 500 2400 - 2483.5 MHz 50 500 5725 - 5875 MHz 50 500 24.0 - 24.25 GHz 250 2500 2. Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: Frequency Field Strength Measurement Distance (MHz) (µV/m) (m) 30-88 100* 3 88-216 150* 3 216-960 200* 3 Above 960 500 3 Remark: Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. 3. In the above emission table, the tighter limit applies at the band edges. Frequency Field Strength Field Strength (MHz) (µV/m at 3-meter) (dBµV/m at 3-meter) 30-88 100 40 88-216 150 43.5 216-960 200 46 Above 960 500 54 Page 20 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 TEST CONFIGURATION 9kHz ~ 30MHz 3m Loop antenna EUT Spectrum / Receiver Turntable 1m 0.8m Reference ground plane Below 1 GHz Antenna tower 3m Bi-log antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Reference ground plane Page 21 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Above 1 GHz Antenna tower 3m Horn antenna EUT 4m Spectrum analyzer Turntable 1m 0.8m Pre-amp TEST PROCEDURE 1. The EUT is placed on a turntable, which is 0.8m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Set the spectrum analyzer in the following setting as: Below 30MHz RBW=9kHz / VBW=300kHz / Sweep=AUTO 30 ~ 1000MHz: RBW=120kHz / VBW=300kHz / Sweep=AUTO Above 1GHz: (a) PEAK: RBW=VBW=1MHz / Sweep=AUTO (b) AVERAGE: RBW=1MHz / VBW=10Hz / Sweep=AUTO 7. Repeat above procedures until the measurements for all frequencies are complete. TEST RESULTS No non-compliance noted. Page 22 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 TEST DATA Below 1 GHz Operation Mode: Normal Link Test Date: 2011/3/21 Temperature: 18°C Tested by: Stan Lin Humidity: 60% RH Polarity: Ver. / Hor. Correction Frequency Ant.Pol. Reading Result Limit Margin Factor Remark (MHz) (H/V) (dBuV) (dBuV/m) (dBuV/m) (dB) (dB/m) 134.3235 V 49.63 -13.45 36.18 43.50 -7.32 QP 199.7500 V 45.98 -15.40 30.58 43.50 -12.92 QP 226.4250 V 46.12 -14.65 31.47 46.00 -14.53 QP 257.9500 V 50.54 -12.32 38.22 46.00 -7.78 QP 398.6000 V 47.94 -9.48 38.46 46.00 -7.54 QP 599.8750 V 42.30 -3.99 38.31 46.00 -7.69 QP 665.3500 V 39.86 -4.39 35.47 46.00 -10.53 QP 143.9750 H 35.78 -12.40 23.38 43.50 -20.12 QP 160.9500 H 34.32 -13.01 21.31 43.50 -22.19 QP 199.7500 H 35.98 -15.40 20.58 43.50 -22.92 QP 493.1750 H 33.00 -7.24 25.76 46.00 -20.24 QP 599.8750 H 35.70 -3.99 31.71 46.00 -14.29 QP 759.9250 H 34.29 -2.15 32.14 46.00 -13.86 QP 944.2250 H 32.68 1.36 34.04 46.00 -11.96 QP Remark: 1. No emission found between lowest internal used / generated frequency to 30 MHz. (9kHz ~ 30MHz) 2. Measuring frequencies from 9 kHz to the 1GHz. 3. Radiated emissions measured in the measured frequency range were made with an instrument using Quasi-peak detector mode. 4. Data of measurement within this frequency range shown “ --- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. The IF bandwidth of SPA between 30MHz to 1GHz was 100kHz. Page 23 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Above 1 GHz Operation Mode: Tx / CH Low Test Date: 2011/3/18 Temperature: 20°C Tested by: Chieh Cheng Humidity: 50% RH Polarity: Ver. / Hor. Ant. Peak AV Ant. / CL Result Peak AV Freq. Margin Pol Reading Reading CF Peak AV Limit Limit Remark (MHz) (dB) H/V (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2403.08 V 79.98 79.25 1.32 81.29 80.57 114.00 94.00 -13.43 AVG 2210.00 V 48.93 --- 0.76 49.69 --- 74.00 54.00 -4.31 Peak 2646.67 V 48.51 --- 1.33 49.84 --- 74.00 54.00 -4.16 Peak 4808.33 V 42.00 --- 6.25 48.26 --- 74.00 54.00 -5.74 Peak N/A 2403.13 H 92.66 92.21 -1.54 91.12 90.67 114.00 94.00 -3.33 AVG 1776.67 H 50.32 --- -4.20 46.12 --- 74.00 54.00 -7.88 Peak 2703.33 H 48.55 --- -0.51 48.04 --- 74.00 54.00 -5.96 Peak 4808.33 H 44.64 --- 7.73 52.37 --- 74.00 54.00 -1.63 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown ”---“ in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with ”N/A” no emission measured remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. Page 24 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Operation Mode: Tx / CH Mid Test Date: 2011/3/18 Temperature: 20°C Tested by: Chieh Cheng Humidity: 50% RH Polarity: Ver. / Hor. Ant. Peak AV Ant. / CL Result Peak AV Freq. Margin Pol Reading Reading CF Peak AV Limit Limit Remark (MHz) (dB) H/V (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2440.15 V 80.85 80.38 1.74 82.59 82.12 114.00 94.00 -11.88 AVG 1753.33 V 50.62 --- -1.75 48.87 --- 74.00 54.00 -5.13 Peak 2826.67 V 48.46 --- 0.94 49.41 --- 74.00 54.00 -4.59 Peak 4883.33 V 44.97 --- 7.44 52.40 --- 74.00 54.00 -1.60 Peak N/A 2440.17 H 93.61 93.15 -1.53 92.08 91.62 114.00 94.00 -2.38 AVG 2076.67 H 49.85 --- -2.12 47.74 --- 74.00 54.00 -6.26 Peak 2563.33 H 49.66 --- -0.41 49.25 --- 74.00 54.00 -4.75 Peak 4883.33 H 45.21 --- 7.75 52.96 --- 74.00 54.00 -1.04 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown ”---“ in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with ”N/A” no emission measured remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. Page 25 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 Operation Mode: Tx / CH High Test Date: 2011/3/18 Temperature: 20°C Tested by: Chieh Cheng Humidity: 50% RH Polarity: Ver. / Hor. Ant. Peak AV Ant. / CL Result Peak AV Freq. Margin Pol Reading Reading CF Peak AV Limit Limit Remark (MHz) (dB) H/V (dBuV) (dBuV) (dB) (dBuV/m) (dBuV/m) (dBuV/m) (dBuV/m) 2479.78 V 83.37 82.89 2.20 85.57 85.09 114.00 94.00 -8.91 AVG 2220.00 V 49.53 --- 0.73 50.25 --- 74.00 54.00 -3.75 Peak 2723.33 V 49.40 --- 1.42 50.82 --- 74.00 54.00 -3.18 Peak 4958.33 V 44.67 --- 6.96 51.62 --- 74.00 54.00 -2.38 Peak N/A 2480.17 H 95.05 94.63 -1.52 93.53 93.11 114.00 94.00 -0.89 AVG 2306.67 H 49.70 --- -1.33 48.36 --- 74.00 54.00 -5.64 Peak 2876.67 H 48.15 --- 0.72 48.87 --- 74.00 54.00 -5.13 Peak 4958.33 H 44.05 --- 8.75 52.81 --- 74.00 54.00 -1.19 Peak N/A Remark: 1. Measuring frequencies from 1 GHz to the 10th harmonic of highest fundamental frequency. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using peak/average detector mode. 3. Average test would be performed if the peak result were greater than the average limit or as required by the applicant. 4. Data of measurement within this frequency range shown ”---“ in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. 5. Measurements above show only up to 6 maximum emissions noted, or would be lesser, with ”N/A” no emission measured remark, if no specific emissions from the EUT are recorded (ie: margin>20dB from the applicable limit) and considered that's already beyond the background noise floor. Page 26 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 7.4 POWERLINE CONDUCTED EMISSIONS LIMIT According to §15.207(a), except as shown in paragraphs (b) and (c) of this section, for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed the limits in the following table, as measured using a 50 µH/50 ohms line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Limits Frequency Range (dBµV) (MHz) Quasi-peak Average 0.15 to 0.50 66 to 56* 56 to 46* 0.50 to 5 56 46 5 to 30 60 50 * Decreases with the logarithm of the frequency. TEST CONFIGURATION See test photographs attached in Appendix 1 for the actual connections between EUT and support equipment. TEST PROCEDURE 1. The EUT was placed on a table, which is 0.8m above ground plane. 2. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 3. Repeat above procedures until all frequency measured were complete. Page 27 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.

Report No: T110315201-RP1 FCC ID: PRDMU01 Date of Issue: March 28, 2011 TEST RESULTS The initial step in collecting conducted data is a spectrum analyzer peak scan of the measurement range. Significant peaks are then marked as shown on the following data page, and these signals are then quasi-peaked. TEST DATA Not applicable (Since the EUT is powered by battery) Page 28 Rev.00 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services.


Document Created: 2011-04-12 12:01:41
Document Modified: 2011-04-12 12:01:41
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC