TestReport.pdf

FCC ID: PJMCPRPOS

Test Report

Download: PDF

FCCID_2697335

Test report no.: 1-0119/15-01-02

1 Table of contents

1 Table of contents ............................................................................................................................................2
2 General information .......................................................................................................................................3
2.1 Notes and disclaimer ..........................................................................................................................3
2.2 Application details ...............................................................................................................................3
3 Test standard/s ...............................................................................................................................................4
3.1 Measurement guidance .......................................................................................................................4
4 Test environment ............................................................................................................................................5
5 Test item ..........................................................................................................................................................5
5.1 Additional information ........................................................................................................................5
6 Test laboratories sub-contracted .................................................................................................................5
7 Description of the test setup .........................................................................................................................6
7.1 Shielded semi anechoic chamber ......................................................................................................7
7.2 Shielded fully anechoic chamber ......................................................................................................8
7.3 Conducted measurements normal and extreme conditions ...........................................................9
7.4 AC conducted ....................................................................................................................................10
8 Measurement uncertainty ............................................................................................................................11
9 Sequence of testing .....................................................................................................................................12
9.1 Sequence of testing 9 kHz to 30 MHz ..............................................................................................12
9.2 Sequence of testing 30 MHz to 1 GHz .............................................................................................13
10 Summary of measurement results ..........................................................................................................14
11 Additional comments ...............................................................................................................................14
12 Measurement results ................................................................................................................................15
12.1 Occupied bandwidth ......................................................................................................................15
12.2 Field strength of the fundamental ................................................................................................17
12.3 Field strength of the harmonics and spurious ...........................................................................18
12.4 Conducted limits ............................................................................................................................21
12.5 Frequency error .............................................................................................................................24
Annex A Document history ..........................................................................................................................25
Annex B Further information ........................................................................................................................25
Annex C Accreditation Certificate ...............................................................................................................26

Page 2 of 26

Test report no.: 1-0119/15-01-02

2 General information

2.1 Notes and disclaimer
The test results of this test report relate exclusively to the test item specified in this test report. CETECOM ICT
Services GmbH does not assume responsibility for any conclusions and generalizations drawn from the test
results with regard to other specimens or samples of the type of the equipment represented by the test item.
The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report
requires the prior written approval of CETECOM ICT Services GmbH.
The testing service provided by CETECOM ICT Services GmbH has been rendered under the current "General
Terms and Conditions for CETECOM ICT Services GmbH".
CETECOM ICT Services GmbH will not be liable for any loss or damage resulting from false, inaccurate,
inappropriate or incomplete product information provided by the customer.
Under no circumstances does the CETECOM ICT Services GmbH test report include any endorsement or
warranty regarding the functionality, quality or performance of any other product or service provided.
Under no circumstances does the CETECOM ICT Services GmbH test report include or imply any product or
service warranties from CETECOM ICT Services GmbH, including, without limitation, any implied warranties of
merchantability, fitness for purpose, or non-infringement, all of which are expressly disclaimed by CETECOM ICT
Services GmbH.
All rights and remedies regarding vendor’s products and services for which CETECOM ICT Services GmbH has
prepared this test report shall be provided by the party offering such products or services and not by CETECOM
ICT Services GmbH.
In no case this test report can be considered as a Letter of Approval.

This test report is electronically signed and valid without handwritten signature. For verification of the electronic
signatures, the public keys can be requested at the testing laboratory.

2.2 Application details
Date of receipt of order: 2015-06-26
Date of receipt of test item: 2015-06-26
Start of test: 2015-06-30
End of test: 2015-07-08
Person(s) present during the test: -/-

Page 3 of 26

Test report no.: 1-0119/15-01-02

4 Test environment
Tnom +22 °C during room temperature tests
Temperature: Tmax +70 °C during high temperature tests
Tmin -20 °C during low temperature tests

Relative humidity content: 46 %

Barometric pressure: not relevant for this kind of testing

Vnom 5.00 V DC by external power supply
Power supply: Vmax 5.75 V
Vmin 4.25 V

5 Test item

Kind of test item : RF Reader
Type identification : ID CPRPOS
HMN : -/-
PMN : ID CPRPOS
HVIN : ID CPRPOS
FVIN : -/-
S/N serial number : MAC-Adr.: 00:1C:9B:0B:00:6D
HW hardware status : No information available!
SW software status : No information available!
Frequency band : 13.56 MHz
Type of radio transmission :
Single modulated carrier
Use of frequency spectrum :
Antenna : Integrated antenna
Power supply : 5.00 V DC by external power supply
Temperature range : -20°C to +70°C

5.1 Additional information
The content of the following annexes is defined in the QA. It may be that not all of the listed annexes are
necessary for this report, thus some values in between may be missing.

Test setup- and EUT-photos are included in test report: 1-0119/15-01-02_AnnexA
1-0119/15-01-02_AnnexB
1-0119/15-01-02_AnnexD

6 Test laboratories sub-contracted
None

Page 5 of 26

Test report no.: 1-0119/15-01-02

7 Description of the test setup
Typically, the calibrations of the test apparatus are commissioned to and performed by an accredited calibration
laboratory. The calibration intervals are determined in accordance with the DIN EN ISO/IEC 17025. In addition to
the external calibrations, the laboratory executes comparison measurements with other calibrated test systems
or effective verifications. Weekly chamber inspections and range calibrations are performed. Where possible, RF
generating and signalling equipment as well as measuring receivers and analysers are connected to an external
high-precision 10 MHz reference (GPS-based or rubidium frequency standard).

In order to simplify the identification of the equipment used at some special tests, some items of test equipment
and ancillaries can be provided with an identifier or number in the equipment list below (Lab/Item).

Agenda: Kind of Calibration

k calibration / calibrated EK limited calibration
ne not required (k, ev, izw, zw not required) zw cyclical maintenance (external cyclical
maintenance)
ev periodic self verification izw internal cyclical maintenance
Ve long-term stability recognized g blocked for accredited testing
vlkI! Attention: extended calibration interval
NK! Attention: not calibrated *) next calibration ordered / currently in progress

Page 6 of 26

Test report no.: 1-0119/15-01-02

8 Measurement uncertainty

Measurement uncertainty
Test case Uncertainty
Occupied bandwidth ± 1 kHz
Field strength of the fundamental ± 3 dB
Field strength of the harmonics and spurious emissions below 30 MHz ± 3 dB
Field strength of the harmonics and spurious emissions 30 MHz to 1 GHz ± 3 dB
Spurious emissions conducted below 30 MHz (AC conducted) ± 2.6 dB
Frequency error ± 10 Hz

Page 11 of 26

Test report no.: 1-0119/15-01-02

9 Sequence of testing

9.1 Sequence of testing 9 kHz to 30 MHz

Setup
 The equipment was setup to simulate a typical usage like descripted in the user manual or
described by manufacturer.
 If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
 If the EUT is a floor standing device, it is placed on the ground.
 Auxiliary equipment and cables were positioned to simulate normal operation conditions as
described in ANSI C 63.4.
 The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
 The measurement distance is 3 meter (see ANSI C 63.4) – see each test details
 The EUT was set into operation.

Premeasurement
 The turntable rotates from 0° to 315° with 45° steps.
 The antenna height is 1.5 meter.
 At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions

Final measurement
 Identified emissions during the premeasurement the software maximizes by rotating the
turntable position (0° to 360°) and by rotating the elevation axces (0° to 360°).
 The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK (QPK / see ANSI C 63.4) detector
 The final levels, frequency, measuring time, bandwidth, turntable position, correction factor,
margin to the limit, and limit will be recorded. Also a plot with the graph of the premeasurement
and the limit will be stored.

Page 12 of 26

Test report no.: 1-0119/15-01-02

9.2 Sequence of testing 30 MHz to 1 GHz

Setup
 The equipment was setup to simulate a typical usage like descripted in the user manual or
described by manufacturer.
 If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground
plane.
 If the EUT is a floor standing device, it is placed on the ground plane with insulation between
both.
 Auxiliary equipment and cables were positioned to simulate normal operation conditions as
described in ANSI C 63.4.
 The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
 The measurement distance is 10 or 3 meter (see ANSI C 63.4) – see each test details
 The EUT was set into operation.
Premeasurement
 The turntable rotates from 0° to 315° with 45° steps.
 The antenna is polarized vertical and horizontal.
 The antenna height changes from 1 to 3 meter.
 At each turntable position, antenna polarization and height the analyzer sweeps three times in
peak to find the maximum of all emissions
Final measurement
 The final measurement will be performed with minimum the six highest peaks.
 According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1
and 4 meter.
 The final measurement will be done with QP (Quasi-Peak / see ANSI C 63.4) detector with an
EMI receiver
 The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization,
turntable angle, correction factor, margin to the limit, and limit will be recorded. Also a plot with
the graph of the premeasurement with marked maximum final measurements and the limit will
be stored.

Page 13 of 26

Test report no.: 1-0119/15-01-02

12 Measurement results

12.1 Occupied bandwidth
Measurement:

The emission bandwidth (x dB) is defined as the frequency range between two points, one above and one
below the carrier frequency, at which the spectral density of the emission is attenuated x dB below the
maximum in-band spectral density of the modulated signal.

Measurement parameters
Detector: Peak
Resolution bandwidth: 1 % – 5 % of the occupied bandwidth
Video bandwidth: ≥ 3x RBW
Trace mode: Max hold
Analyser function: 99 % power function
Used equipment: See chapter 7.3 - A
Measuremnt uncertainty See chapter 8

Limit:

IC
for RSP-100 test report coversheet only

Result:

99% emission bandwidth
379 kHz

Page 15 of 26

Test report no.: 1-0119/15-01-02

12.2 Field strength of the fundamental
Measurement:

The maximum detected field strength for the carrier signal.

Measurement parameters
Detector: Quasi peak / peak (worst case)
Resolution bandwidth: 120 kHz
Video bandwidth: ≥ 3x RBW
Trace mode: Max hold
Used equipment: See chapter 7.2 - A
Measuremnt uncertainty See chapter 8

Limit:

FCC & IC
Frequency Field strength Measurement distance
(MHz) (µV/m) (m)
13.553 to 13.567 15,848 (84 dBµV/m) 30

Recalculation:

According to ANSI C63.10
Frequency Formula Correction value
𝑑nearfield 𝑑𝑙𝑖𝑚𝑖𝑡
13.56 MHz FSlimit = FSmax −40 log ( ) − 20log⁡( ) -21.39
𝑑𝑚𝑒𝑎𝑠𝑢𝑟𝑒 𝑑𝑛𝑒𝑎𝑟𝑓𝑖𝑒𝑙𝑑

According to ANSI C63.10

Result:

Field strength of the fundamental
Frequency 13.56 MHz
Distance @3m @ 30 m
Measured / calculated value – without Tag 70.1 dBµV/m 48.7 dBµV/m
Measured / calculated value – with Tag 67.8 dBµV/m 46.4 dBµV/m

Page 17 of 26

Test report no.: 1-0119/15-01-02

12.3 Field strength of the harmonics and spurious
Measurement:

The maximum detected field strength for the harmonics and spurious.

Measurement parameters
Quasi peak / average or
Detector:
peak (worst case – pre-scan)
F < 150 kHz: 200 Hz
Resolution bandwidth: 150 kHz < F < 30 MHz: 9 kHz
30 MHz < F < 1 GHz: 120 kHz
F < 150 kHz: 1 kHz
Video bandwidth: 150 kHz < F < 30 MHz: 100 kHz
30 MHz < F < 1 GHz: 300 kHz
Trace mode: Max hold
Used equipment: See chapter 7.1 - A, 7.2 - A, 7.3 - A
Measuremnt uncertainty See chapter 8

Limit:

FCC & IC

Frequency Field strength Measurement distance
(MHz) (dBµV/m) (m)
0.009 – 0.490 2400/F(kHz) 300
0.490 – 1.705 24000/F(kHz) 30
1.705 – 30 30 (29.5 dBµV/m) 30
30 – 88 100 (40 dBµV/m) 3
88 – 216 150 (43.5 dBµV/m) 3
216 – 960 200 (46 dBµV/m) 3

Note: For a reduced measurement distance, please take a look at the limit line and the ANSI C63.10-2013
sub clause 6.4 radiated emissions from unlicensed wireless devices below 30 MHz.

Result:

Detected emissions
Frequency Resolution bandwidth
Detector Detected value
(MHz) (kHz)
40.7 MHz QP 120 28.6 dBµV/m @ 10m
200 MHz QP 120 24.5 dBµV/m @ 10m

Page 18 of 26

Test report no.: 1-0119/15-01-02

Plot 3: 30 MHz – 1 GHz, vertical and horizontal polarisation

60

55

50

45

40
F CC _ 1 0 m_ B
Level in dBµV/m

35

30

25

20

15

10

5

0
30M 50 60 80 100M 200 300 400 600M
F re q u e n c y in H z

Final_Result:

Meas.
Frequency QuasiPeak Limit Margin Bandwidth Height Azimuth Corr.
Time Pol
(MHz) (dBµV/m) (dBµV/m) (dB) (kHz) (cm) (deg) (dB)
(ms)
40.671600 28.61 30.00 1.39 1000.0 120.000 98.0 V 117 14.0
199.994100 24.47 33.50 9.03 1000.0 120.000 100.0 V 297 11.7
350.002650 33.20 36.00 2.80 1000.0 120.000 200.0 H 97 16.0
449.982900 33.01 36.00 2.99 1000.0 120.000 178.0 H 97 17.6
499.976550 34.62 36.00 1.38 1000.0 120.000 173.0 H 277 18.7
549.994800 32.07 36.00 3.93 1000.0 120.000 103.0 H 97 19.3

Page 20 of 26

Test report no.: 1-0119/15-01-02

12.4 Conducted limits
Measurement:

Measurement of the conducted spurious emissions for an intentional radiator that is designed to be connected
to the public utility (AC) power line.

Measurement parameters
Quasi peak / average or
Detector:
peak (worst case – pre-scan)
F < 150 kHz: 200 Hz
Resolution bandwidth:
F > 150 kHz: 9 kHz
F < 150 kHz: 1 kHz
Video bandwidth:
F > 150 kHz: 100 kHz
Trace mode: Max hold
Used equipment: See chapter 7.4 - A
Measuremnt uncertainty See chapter 8

Limit:

FCC & IC
Frequency Quasi-peak Average
(MHz) (dBµV/m) (dBµV/m)
0.15 – 0.5 66 to 56* 56 to 46*
0.5 – 5 56 46
5 – 30.0 60 50

Measurement arrangement:

The EUT housing was opened up and a twisted pair cable was soldered direct on V+ and GND of the soldering
points of the standard connector to make sure that only the DC line is connected and no other port like serial
port which is also on the standard connector.

Page 21 of 26

Test report no.: 1-0119/15-01-02

Plots:

Plot 1: 150 kHz to 30 MHz, phase line

FCC Premeasurement
Average limit class B
Measurement Quasi peak limit class B
L_Peaks_fin
Phase line Average level
Quasi peak level

80.0

70.0

60.0

50.0
Amplitude in dBµV

40.0

30.0

20.0

10.0

0
100.0K 1.0M 10.0M 100.0M
Frequency in Hz
Project ID: 1-0119/15-01-02

Quasi peak Margin quasi
Frequency Average level Margin average
level peak
MHz dBµV dBµV dBµV dBµV

13.562 47.10 12.90 46.85 3.15
20.004 30.32 29.68 25.16 24.84
25 30.69 29.31 30.38 19.62

Page 22 of 26

Test report no.: 1-0119/15-01-02

Plot 2: 150 kHz to 30 MHz, neutral line

FCC Premeasurement
Average limit class B
Measurement Quasi peak limit class B
N_Peaks_fin
Neutral line Average level
Quasi peak level

80.0

70.0

60.0

50.0
Amplitude in dBµV

40.0

30.0

20.0

10.0

0
100.0K 1.0M 10.0M 100.0M
Frequency in Hz
Project ID: 1-0119/15-01-02

Quasi peak Margin quasi
Frequency Average level Margin average
level peak
MHz dBµV dBµV dBµV dBµV

13.56 48.21 11.79 47.89 2.11
20 34.58 25.42 29.84 20.16
25.005 22.96 37.04 21.74 28.26

Page 23 of 26

Test report no.: 1-0119/15-01-02

12.5 Frequency error
Measurement:

The maximum detected field strength for the spurious.

Measurement parameters
Detector: Peak detector
Resolution bandwidth: 10 Hz
Video bandwidth: > RBW
Trace mode: Clear Write
Used equipment: See chapter 7.3 - A
Measuremnt uncertainty See chapter 8

Limit:

FCC
The frequency tolerance of the carrier signal shall be maintained within +/- 0.01% of the operating
frequency over a temperature variation of -20 degrees to +50 degrees C at normal supply voltage,
and for a variation in the primary supply voltage from 85% to 115% of the rated supply voltage at a
temperature of 20 degrees C. (±1.356 kHz)

Result: Temperature variation

Frequency tolerance
Measured frequency
Conditions Result
(MHz)
13.5602 -20 °C & 100% voltage complaint
13.5601 -10 °C & 100% voltage complaint
13.5601 0 °C & 100% voltage complaint
13.5601 +10 °C & 100% voltage complaint
13.5601 +20 °C & 100% voltage complaint
13.5601 +30 °C & 100% voltage complaint
13.5601 +40 °C & 100% voltage complaint
13.5601 +50 °C & 100% voltage complaint

Result: Voltage variation

Frequency tolerance
Measured frequency
Temperature Result
(MHz)
13.5601 +20 °C & 85% voltage complaint
13.5601 +20 °C & 100% voltage complaint
13.5601 +20 °C & 115% voltage complaint

Page 24 of 26

Test report no.: 1-0119/15-01-02

Annex A Document history

Version Applied changes Date of release

Initial release 2015-07-29

Annex B Further information
Glossary

AVG - Average
DUT - Device under test
EMC - Electromagnetic Compatibility
EN - European Standard
EUT - Equipment under test
ETSI - European Telecommunications Standard Institute
FCC - Federal Communication Commission
FCC ID - Company Identifier at FCC
HW - Hardware
IC - Industry Canada
Inv. No. - Inventory number
N/A - Not applicable
PP - Positive peak
QP - Quasi peak
S/N - Serial number
SW - Software
PMN Product marketing name
HMN Host marketing name
HVIN Hardware version identification number
FVIN Firmware version identification number

Page 25 of 26

Document Created: 2015-07-29 07:45:28
Document Modified: 2015-07-29 07:45:28

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC