Test Report

FCC ID: OSGZBM

Test Report

Download: PDF
FCCID_1758807

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr FCC TEST REPORT Test report No: EMC- FCC- R0069 FCC ID: OSGZBM Type of Equipment: ZigBee Module Model Name: ZBM Applicant: GeneTel Systems, Inc. FCC Rule Part(s): FCC Part 15 Subpart C Section 15.203, Section 15.209 Section 15.207, Section 15.247 Frequency Range: 2 405 MHz ~ 2 480 MHz Test result: Complied The above equipment was tested by EMC compliance Testing Laboratory for compliance with the requirements of FCC Rules and Regulations. The results of testing in this report apply to the product/system which was tested only. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties. Date of test: July 16, 2012 ~ July 19, 2012 Issued date: July 23, 2012 Tested by: Approved by: . LEE, CHANG WON KIM, CHANG MIN EMC compliance Ltd. Page: 1 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr [ Contents ] 1. Client information ................................................................................................. 3 2. Laboratory information ........................................................................................... 4 3. Description of E.U.T................................................................................................ 5 3.1 Basic description................................................................................................ 5 3.2 General description ............................................................................................ 5 3.3 Test frequency................................................................................................... 6 3.4 Test Voltage ..................................................................................................... 6 4. Summary of test results............................................................................................ 7 4.1 Standards & results ............................................................................................. 7 4.2 Uncertainty...................................................................................................... 7 5. Test results .......................................................................................................... 8 5.1 Antenna Requirement........................................................................................... 8 5.2 Maximum Peak Output Power ................................................................................. 9 5.3 Peak Power Spectral Density..................................................................................13 5.4 6 dB Bandwidth ...............................................................................................17 5.5 SPURIOUS EMISSION, BAND EDGE, AND RESTRICTED BANDS ..................................22 5.6 Conducted Emission ..........................................................................................31 5.7 RF Exposure ...................................................................................................32 6. Test equipment used for test .................................................................................... 33 Appendix 1 Test setup photos Appendix 2 External photos of EUT Appendix 3 Internal photos of EUT Appendix 4 Block diagram Appendix 5 Schematics Appendix 6 User manual Appendix 7 Part list Appendix 8 Layout diagram Appendix 9 Antenna Specification EMC compliance Ltd. Page: 2 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 1. Client information Applicant: GeneTel Systems, Inc. Address: 518 Yongsan-Dong Yuseong-Gu Daejoen, Korea Telephone number: +82-42-335-3001 Facsimile number : +82-42-335-3003 Contact person: JONG-UK CHAE / juchae@genetel.co.kr Manufacturer : GeneTel Systems, Inc. Address: #518 Yongsan-Dong Yuseong-Gu Daejoen, Korea EMC compliance Ltd. Page: 3 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 2. Laboratory information Address EMC Compliance Ltd. 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea Telephone Number: 82 31 336 9919 Facsimile Number: 82 31 336 4767 Certificate CBTL Testing Laboratory, KOLAS NO.: 231 FCC Filing No.: 508785 VCCI Registration No.: C-1713, R-1606, T-258 SITE MAP SUWON-CITY EMC Compliance Ltd. EMC compliance Ltd. Page: 4 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 3. Description of E.U.T. 3.1 Basic description Applicant : GeneTel Systems, Inc. Address of 518 Yongsan-Dong Yuseong-Gu Daejoen, Korea Applicant: Manufacturer: GeneTel Systems, Inc. Address of 518 Yongsan-Dong Yuseong-Gu Daejoen, Korea Manufacturer: Type of equipment: ZigBee Module Basic Model: ZBM Serial number: Proto Type 3.2 General description Model Name ZigBee Module Communication IEEE 802.15.4 Frequency Range 2 405 ~ 2 480 MHz Type of Modulation O-QPSK Channel capacity 16 ch Antenna Gain 3.94 dBi Type of Antenna Chip ANTENNA Power supply DC 3.3 V Operating temperature -20 ~ 55 °C Dimension 26 mm x 21 mm x 3 mm EMC compliance Ltd. Page: 5 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 3.3 Test frequency Frequency Low frequency 2 405 MHz Middle frequency 2 445 MHz High frequency 2 480 MHz 3.4 Test Voltage mode Voltage Norminal voltage DC 3.3 V EMC compliance Ltd. Page: 6 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 4. Summary of test results 4.1 Standards & results Report Test Rule Reference Parameter Section Result 15.203, Antenna Requirement 5.1 C 15.247(b)(4) 15.247(b)(3) Maximum Peak Output Power 5.2 C 15.247(e) Peak Power Spectral Density 5.3 C 15.247(a)(2) 6 dB Channel Bandwidth 5.4 C 15.247(d), Spurious Emission, Band Edge, 15.205(a), 5.5 C and Restricted bands 15.209(a) 15.207(a) Conducted Emissions 5.6 N/A 15.247(i), RF Exposure 5.7 C 1.1307(b)(1) Note: C=complies NC= Not complies NT=Not tested NA=Not Applicable 4.2 Uncertainty Combined Standard Expanded Measurement Item Uncertainty Uncertainty Uc U = KUc (K = 2) Conducted RF power ± 0.75 dB ± 1.3 dB Radiated disturbance +2.280dB / - 2.278 dB +4.560dB / - 4.556 dB Conducted disturbance +1.883 dB / - 1.676 dB +3.766dB / - 3.352 dB EMC compliance Ltd. Page: 7 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5. Test results 5.1 Antenna Requirement 5.1.1 Regulation According to §15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. And according to §15.247(b)(4), the conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. 5.1.2 Result -Complied The transmitter has an integral Chip antenna. type of antenna connector reverse sma female. The directional gain of the antenna is 3.94 dBi. EMC compliance Ltd. Page: 8 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

EMC _ FCC TEST REPORT comnllance Report No.: EMC—FCC—RO069 http://www.cm c2000.c0.kr 5.2 Maximum Peak Output Power 5.2.1 Regulation According to §15.247(b)(3), For systemsusing digital modulation in the 902—928 MHz, 2400—2483.5 MHz, and 5725—5850 MHz bands: 1 Watt. As an alternative to a peak power measurement, compliance with the one Watt limit can be based on a measurement of the maximum conducted output power. Maximum Conducted. Output Poweris defined as the total transmit power delivered to all antennas and antenna elements averaged actoss all symbols in the signaling alphabet when the transmitter is operating at its maximum power control level. Power must be summed across all antennas and antenna elements. The average must not include any time intervals during which the transmitter is off or is transmitting at a reduced powerlevel. If multiple modes of operation are possible (e.g., alternative modulation methods), the maximum conducted output power is the highest total transmit power occurring in any mode. According to §15.247(b)(4) The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, iftransmitting antennas ofdirectional gain greater than 6 dBi are used, the conducted output power from the intentionalradiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain ofthe antenna exceeds 6 dBi. 5.2.2 Measurement Procedure 5.2.2.1 Measurement Procedure PK1: 1. This procedure requires availability of a spectrum analyzer resolution bandwidth that is > EBW 2. Set the RBW 2 EBW 3. Set VBW > 3 x RBW. 4. Set span= zero. 5. Sweep time= auto couple. 6. Detector = peak. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use peak marker function to determine the peak amplitude level within the fundamental emission. EMC compliance Ltd. Page: 9 of 33 480—5 Shin—dong, Yeongtong—gu, Suwon—city, Gyunggi—do, 443—390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fex) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.2.3 Test Result -Complied Frequency Result Limit Margin Channel (MHz) (dBm) (dBm) (dB) Low 2 405 -2.52 30.00 32.52 Middle 2 445 -2.24 30.00 32.24 High 2 480 -2.52 30.00 32.52 -NOTE: 1. Since the directional gain of the integral antenna declared by the manufacturer (GANT = 1 dBi) does not exceed 6.0 dBi, there was no need to reduce the output power. 2. We took the insertion loss of the cable loss into consideration within the measuring instrument. EMC compliance Ltd. Page: 10 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.2.4 Test Plot Figure 1. Plot of the Maximum Peak Output Power - Lowest Channel( 2 405 MHz) RBW 3 MHz Marker 1 [T1 ] * VBW 10 MHz -2.52 dBm Ref 10 dBm Att 40 dB SWT 5 ms 70.000000 µs 10 1 A 0 1 PK MAXH -10 TDF -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.405 GHz 500 µs/ - Middle Channel (2 445 MHz) RBW 3 MHz Marker 1 [T1 ] * VBW 10 MHz -2.24 dBm Ref 10 dBm Att 40 dB SWT 5 ms 750.000000 µs 10 1 A 0 1 PK MAXH -10 TDF -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.445 GHz 500 µs/ Date: 23.JUL.2012 22:28:55 EMC compliance Ltd. Page: 11 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr - Highest Channel (2 480 MHz) RBW 3 MHz Marker 1 [T1 ] * VBW 10 MHz -2.52 dBm Ref 10 dBm Att 40 dB SWT 5 ms 1.470000 ms 10 1 A 0 1 PK MAXH -10 TDF -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.48 GHz 500 µs/ Date: 23.JUL.2012 22:28:17 EMC compliance Ltd. Page: 12 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

EMC _ FCC TEST REPORT comnllance Report No.: EMC—FCC—RO069 http://www.cm c2000.c0.kr 5.3 Peak Power Spectral Density 5.3.1 Regulation According to §15.247(c), for digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. This power spectral density shall be determinedin accordance with the provisions of paragraph (b) of this section. The same method of determining the conducted output power shall be used to determine the power spectral density. 5.3.2 Measurement Procedure Measurement Procedure PKPSD: 1. Use this procedure when the maximum peak conducted output power in the fundamental emission is used to demonstrate compliance. Set the RBW = 100 kHz. on Set the VBW 2z 300 kHz. w Set the span to 5—30 % greater than the EBW s Detector= peak. s Sweep time = auto couple. a Trace mode = max hold. =a Allow trace to fully stabilize. m Use the peak marker function to determine the maximum power level in any 100 kHz band segment within the o fundamental EBW 10. Scale the observed power level to an equivalent value in 3 kHz by adjusting (reducing) the measured power by a bandwidth correction factor (BWCF) where BWCF = 10log(3 kHz/100 kHz= —15.2 dB). 11. The resulting peak PSD level must be = 8 dBm. EMC compliance Ltd. Page: 13 of 33 480—5 Shin—dong, Yeongtong—gu, Suwon—city, Gyunggi—do, 443—390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fex) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.3.3 Test Result -Complied Reading BWCF Result Limit Margin Channel [dBm] [dB] [dBm] [dBm] [dBm] Low -5.07 -15.20 -20.27 8.00 28.27 Middle -4.69 -15.20 -19.89 8.00 27.89 High -5.61 -15.20 -20.81 8.00 28.81 NOTE: We took the insertion loss of the cable loss into consideration within the measuring instrument. EMC compliance Ltd. Page: 14 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.3.4 Test Plot Figure 2. Plot of the Power Density (Conducted) - Lowest Channel( 2 405 MHz) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -5.07 dBm Ref 10 dBm Att 40 dB SWT 2.5 ms 2.404760000 GHz 10 A 0 1 1 PK MAXH -10 TDF -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.405 GHz 300 kHz/ Span 3 MHz - Middle Channel (2 445 MHz) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -4.69 dBm Ref 10 dBm Att 40 dB SWT 2.5 ms 2.444718000 GHz 10 A 0 1 1 PK MAXH -10 TDF -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.445 GHz 300 kHz/ Span 3 MHz EMC compliance Ltd. Page: 15 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr - Highest Channel (2 480 MHz) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -5.61 dBm Ref 10 dBm Att 40 dB SWT 2.5 ms 2.480252000 GHz 10 A 0 1 1 PK MAXH -10 TDF -20 -30 -40 3DB -50 -60 -70 -80 -90 Center 2.48 GHz 300 kHz/ Span 3 MHz EMC compliance Ltd. Page: 16 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.4 6 dB Bandwidth 5.4.1 Regulation Systems using digital modulation techniques may operate in the 902 - 928 MHz, 2400 - 2483.5 MHz, and 5725 - 5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 5.4.2 Measurement Procedure The antenna output of the EUT was connected to the spectrum analyzer. The resolution bandwidth is set to 100 kHz, and peak detection was used. The 6dB bandwidth is defined as the total spectrum over which the power is higher than the peak power minus 6dB. EMC compliance Ltd. Page: 17 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.4.3 Test Result -Complied 99% Occupied Frequency 6dB Bandwidth Min. Limit Channel Bandwidth (MHz) (MHz) (kHz) (MHz) Low 2 405 1.392 2.070 500 Middle 2 445 1.350 2.046 500 High 2 480 1.374 2.088 500 EMC compliance Ltd. Page: 18 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.4.4 Test Plot Figure 3. Plot of the 6dB Bandwidth (Conducted) - Lowest Channel (2 405 MHz) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -17.58 dBm Ref 0 dBm Att 30 dB SWT 2.5 ms 2.405240000 GHz 0 ndB [T1] 6.00 dB BW 1.392000000 MHz Temp 1 [T1 ndB] A -10 1 -23.62 dBm 1 PK D1 -17.58 dBm 2.404298000 GHz MAXH -20 T1 T2 Temp 2 [T1 ndB] D2 -23.58 dBm -23.59 dBm 2.405690000 GHz TDF -30 -40 -50 3DB -60 -70 -80 -90 F2 F1 -100 Center 2.405 GHz 300 kHz/ Span 3 MHz Date: 19.JUL.2012 16:06:44 * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -17.63 dBm Ref 0 dBm Att 20 dB SWT 2.5 ms 2.405258000 GHz 0 OBW 2.070000000 MHz Temp 1 [T1 OBW] -33.16 dBm A -10 2.403962000 GHz 1 PK 1 Temp 2 [T1 OBW] MAXH -20 -32.95 dBm 2.406032000 GHz TDF -30 T1 T2 -40 -50 3DB -60 -70 -80 -90 -100 Center 2.405 GHz 300 kHz/ Span 3 MHz Date: 19.JUL.2012 16:07:13 EMC compliance Ltd. Page: 19 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr - Middle Channel (2 445MHz) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -15.20 dBm Ref 0 dBm Att 30 dB SWT 2.5 ms 2.444742000 GHz 0 ndB [T1] 6.00 dB BW 1.350000000 MHz Temp 1 [T1 ndB] A -10 1 -20.93 dBm 1 PK D1 -15.2 dBm T1 T2 2.444316000 GHz MAXH -20 D2 -21.2 dBm Temp 2 [T1 ndB] -21.04 dBm 2.445666000 GHz TDF -30 -40 -50 3DB -60 -70 -80 -90 F2 F1 -100 Center 2.445 GHz 300 kHz/ Span 3 MHz Date: 19.JUL.2012 16:08:58 * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -15.24 dBm Ref 0 dBm Att 20 dB SWT 2.5 ms 2.445228000 GHz 0 OBW 2.046000000 MHz Temp 1 [T1 OBW] -31.65 dBm A -10 1 2.443962000 GHz 1 PK Temp 2 [T1 OBW] MAXH -20 -30.31 dBm 2.446008000 GHz T1 T2 TDF -30 -40 -50 3DB -60 -70 -80 -90 -100 Center 2.445 GHz 300 kHz/ Span 3 MHz Date: 19.JUL.2012 16:07:49 EMC compliance Ltd. Page: 20 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr - Highest Channel (2 480 MHz) * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -13.72 dBm Ref 0 dBm Att 30 dB SWT 2.5 ms 2.479724000 GHz 0 ndB [T1] 6.00 dB BW 1.374000000 MHz Temp 1 [T1 ndB] A -10 1 D1 -13.72 dBm -19.73 dBm 1 PK T1 T2 2.479304000 GHz VIEW -20 D2 -19.72 dBm Temp 2 [T1 ndB] -19.70 dBm 2.480678000 GHz TDF -30 -40 -50 3DB -60 -70 -80 -90 F2 F1 -100 Center 2.48 GHz 300 kHz/ Span 3 MHz Date: 19.JUL.2012 16:11:23 * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -14.11 dBm Ref 0 dBm Att 20 dB SWT 2.5 ms 2.479706000 GHz 0 OBW 2.088000000 MHz Temp 1 [T1 OBW] -28.85 dBm A -10 1 2.478956000 GHz 1 PK Temp 2 [T1 OBW] MAXH -20 -28.59 dBm 2.481044000 T2 GHz T1 TDF -30 -40 -50 3DB -60 -70 -80 -90 -100 Center 2.48 GHz 300 kHz/ Span 3 MHz Date: 19.JUL.2012 16:12:00 EMC compliance Ltd. Page: 21 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.5 SPURIOUS EMISSION, BAND EDGE, AND RESTRICTED BANDS 5.5.1 Regulation According to §15.247(d), in any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in Section 15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section 15.205(a), must also comply with the radiated emission limits specified in Section 15.209(a) (see Section 15.205(c)). According to §15.209(a), for an intentional device, the general requirement of field strength of radiated emissions from intentional radiators at a distance of 3 meters shall not exceed the following values: Frequency (MHz) Field strength (µV/m @ 3m) Field strength (dBµV/m @ 3m) 30–88 100 40.0 88–216 150 43.5 216–960 200 46.0 Above 960 500 54.0 According to §15.109(a), for an unintentional device, except for Class A digital devices, the field strength of radiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the above table. ** The emission limits shown in the above table are based on measurement instrumentation employing a CISPR quasi-peak detector and above 1000 MHz are based on the average value of measured emissions. EMC compliance Ltd. Page: 22 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.5.2 Measurement Procedure 1) Band-edge Compliance of RF Conducted Emissions 2) 1. Set the spectrum analyzer as follows: Span = wide enough to capture the peak level of the emission operating on the channel closest to the bandedge, as well as any modulation products which fall outside of the authorized band of operation RBW  1% of the span VBW  RBW Sweep = auto Detector function = peak Trace = max hold 2. Allow the trace to stabilize. Set the marker on the emission at the band-edge, or on the highest modulation product outside of the band, if this level is greater than that at the band-edge. Enable the marker-delta function, and then use the marker-to-peak function to move the marker to the peak of the in-band emission. 3. Now, using the same instrument settings, enable the hopping function of the EUT. Allow the trace to stabilize. Follow the same procedure listed above to determine if any spurious emissions caused by the hopping function also comply with the specified limit. 2) Spurious RF Conducted Emissions: 1. Set the spectrum analyzer as follows: Span = wide enough to capture the peak level of the in-band emission and all spurious emissions (e.g., harmonics) from the lowest frequency generated in the EUT up through the 10th harmonic. Typically, several plots are required to cover this entire span. RBW = 100 kHz VBW  RBW Sweep = auto Detector function = peak Trace = max hold 2. Allow the trace to stabilize. Set the marker on the peak of any spurious emission recorded. a 4 × 4 meter at the Open Area Test Site. The EUT was tested at a distance 3 meters. 5. Each frequency found during preliminary measurements was re-examined and investigated. The test- receiver system was set up to average, peak, and quasi-peak detector function with specified bandwidth. EMC compliance Ltd. Page: 23 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 3) Spurious Radiated Emissions: 1. The preliminary radiated measurements were performed to determine the frequency producing the maximum emissions in an anechoic chamber at a distance of 3 meters. 2. The EUT was placed on the top of the 0.8-meter height, 1 × 1.5 meter non-metallic table. To find the maximum emission levels, the height of a measuring antenna was changed and the turntable was rotated 360˚. 3. The antenna polarization was also changed from vertical to horizontal. The spectrum was scanned from 9 kHz to 30 MHz using the loop antenna, and from 30 to 1000 MHz using the TRILOG broadband antenna, and from 1000 MHz to 26500 MHz using the horn antenna. 4. To obtain the final measurement data, the EUT was arranged on a turntable situated on a 4 × 4 meter at the Open Area Test Site. The EUT was tested at a distance 3 meters. 5. Each frequency found during preliminary measurements was re-examined and investigated. The test-receiver system was set up to average, peak, and quasi-peak detector function with specified bandwidth. EMC compliance Ltd. Page: 24 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.5.3 Test Result -complied 1. Band edge compliance of RF Conducted Emissions was shown in figure 4. 2. Band edge compliance of RF Radiated Emissions was shown in figure 5. 3. Spurious RF conducted Emissions were shown in the Figure 6. Note: We took the insertion loss of the cable into consideration within the measuring instrument. 4. Measured value of the Field strength of spurious Emissions (Radiated) - Low channel (2 405 MHz) Receiver Frequency Pol. Reading Factor Result Limit Margin Bandwidth [MHz] [kHz] [V/H] [dB(μV)] [dB] [dB(μV/m)] [dB(μV/m)] [dB] Quasi-Peak DATA. Emissions below 30 MHz 9.102 9 V 22.0* -18.8 3.2 29.5 26.3 Quasi-Peak DATA. Emissions below 1GHz 81.842 120 V 37.9 -18.1 19.8 40.0 20.2 124.267 120 H 35.3 -15.3 20.0 43.5 23.5 Peak DATA. Emissions above 1GHz 2 351.223 1 000 H 44.4 -1.9 42.5 74.0 31.5 4 810.035 1 000 H 55.2 6.0 61.2 74.0 12.8 Above Not - - - - - - 4 900.000 Detected Average DATA. Emissions above 1GHz 2 351.760 1 000 H 31.6 -1.9 29.7 54.0 24.3 4 810.035 1 000 H 41.2 6.0 47.2 54.0 6.8 Above Not - - - - - - 4 900.000 Detected * Test Distance: 3m Spec Distance: 30m Reading value = reading + Distance correction factor(-20 dB) = 22.0 dB EMC compliance Ltd. Page: 25 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr - Middle channel (2 445 MHz) Receiver Frequency Pol. Reading Factor Result Limit Margin Bandwidth [MHz] [kHz] [V/H] [dB(μV)] [dB] [dB(μV/m)] [dB(μV/m)] [dB] Quasi-Peak DATA. Emissions below 30 MHz 9.102 9 V 21.8* -18.8 3.0 29.5 26.5 Quasi-Peak DATA. Emissions below 1GHz 135.245 120 V 35.4 -14.5 20.9 43.5 22.6 184.715 120 V 34.8 -15.2 19.6 43.5 23.9 Peak DATA. Emissions above 1GHz 4 888.895 1 000 H 57.1 6.0 63.1 74.0 10.9 Above Not - - - - - - 4 900.000 Detected Average DATA. Emissions above 1GHz 4 888.895 1 000 H 44.9 6.0 50.9 54.0 3.1 Above Not - - - - - - 4 900.000 Detected * Test Distance: 3m Spec Distance: 30m Reading value = reading + Distance correction factor(-20 dB) = 21.8 dB EMC compliance Ltd. Page: 26 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr - High channel (2 480 MHz) Receiver Frequency Pol. Reading Factor Result Limit Margin Bandwidth [MHz] [kHz] [V/H] [dB(μV)] [dB] [dB(μV/m)] [dB(μV/m)] [dB] Quasi-Peak DATA. Emissions below 30 MHz 9.102 9 V 22.2* -18.8 3.4 29.5 26.1 Quasi-Peak DATA. Emissions below 1GHz 85.834 120 V 38.7 -19.0 19.7 40.0 20.3 126.893 120 V 35.1 15.1 20.0 43.5 23.5 Peak DATA. Emissions above 1GHz 2 483.520 1 000 H 53.2 -1.7 51.5 74.0 22.5 4 959.179 1 000 H 51.7 6.1 57.8 74.0 16.2 Above Not - - - - - - 5 000.000 Detected Average DATA. Emissions above 1GHz 2 483.500 1 000 H 46.6 -1.7 44.9 54.0 9.1 4 959.179 1 000 H 43.1 6.1 49.2 54.0 4.8 Above Not - - - - - - 5 000.000 Detected * Test Distance: 3m Spec Distance: 30m Reading value = reading + Distance correction factor(-20 dB) = 22.2 dB Factor(dB) = ANT Factor+ Amp Gain + Cable Loss Margin (dB) = Limit - Result [Result = Reading – Factor] 1. H = Horizontal, V = Vertical Polarization 2. ATT = Attenuation (10dB pad and/or Insertion Loss of HPF), AF/CL = Antenna Factor and Cable Loss  The spurious emission at the frequency does not fall in the restricted bands.  The measured result is within the test standard limit by a margin less than the measurement uncertainty; it is therefore not possible to state compliance based on the 95 % level of confidence. However, the result indicates that compliance is more probable than non- compliance. NOTE: All emissions not reported were more than 20 dB below the specified limit or in the noise floor. EMC compliance Ltd. Page: 27 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.5.4 Test Plot Figure 4. Plot of the Band Edge (Conducted) - Lowest Channel (2 405 MHz) * RBW 100 kHz Marker 3 [T1 ] * VBW 300 kHz -59.29 dBm Ref 0 dBm Att 30 dB SWT 10 ms 2.339800000 GHz 0 Marker 1 [T1 ] -17.20 dBm 2.404800000 GHz A -10 Marker 2 [T1 ] 1 1 PK D1 -17.2 dBm -59.44 dBm MAXH -20 2.386600000 GHz TDF -30 D2 -37.2 dBm -40 -50 3 2 3DB -60 -70 -80 -90 F2 F1 -100 Center 2.36 GHz 10 MHz/ Span 100 MHz - Highest Channel (2 480MHz) * RBW 100 kHz Marker 4 [T1 ] * VBW 300 kHz -60.27 dBm Ref 0 dBm Att 30 dB SWT 10 ms 2.522400000 GHz 0 Marker 1 [T1 ] -13.99 dBm 2.480200000 GHz A -10 1 D1 -13.96 dBm Marker 2 [T1 ] 1 PK -60.38 dBm MAXH -20 2.486800000 GHz Marker 3 [T1 ] -60.23 dBm TDF -30 2.510600000 GHz D2 -33.96 dBm -40 -50 3DB 2 3 4 -60 -70 -80 -90 F2 F1 -100 Center 2.502 GHz 10 MHz/ Span 100 MHz EMC compliance Ltd. Page: 28 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.5.5 Test Plot (Continue) Figure 5. Plot of the Band Edge (Radiated) Lowest Channel(2 405 MHz): PEAK Lowest Channel(2 405 MHz): AVERAGE * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] * VBW 1 MHz 44.39 dBµV * VBW 10 Hz 31.62 dBµV Ref 90 dBµV * Att 10 dB SWT 40 ms 2.351222588 GHz Ref 90 dBµV * Att 10 dB SWT 1.2 s 2.351760150 GHz 90 Offset -1.9 dB 90 Offset -1.9 dB A A 80 80 1 PK D1 74 dBµV 1 PK D1 74 dBµV MAXH MAXH 70 70 LVL LVL 60 60 D2 54 dBµV D2 54 dBµV 50 50 1 40 40 3DB 1 3DB 30 30 20 20 10 10 0 0 -10 -10 Center 2.35 GHz 470 kHz/ Span 4.7 MHz Center 2.35 GHz 470 kHz/ Span 4.7 MHz Highest Channel(2 480 MHz): PEAK Highest Channel(2 480 MHz): AVERAGE * RBW 1 MHz Marker 1 [T1 ] * RBW 1 MHz Marker 1 [T1 ] * VBW 1 MHz 53.21 dBµV * VBW 10 Hz 46.55 dBµV Ref 90 dBµV * Att 10 dB SWT 40 ms 2.483520625 GHz Ref 90 dBµV * Att 10 dB SWT 4.2 s 2.483500000 GHz 90 Offset -1.7 dB 90 Offset -1.7 dB A A 80 80 1 PK D1 74 dBµV 1 PK D1 74 dBµV MAXH MAXH 70 70 LVL LVL 60 60 1 D2 54 dBµV D2 54 dBµV 50 1 50 40 40 3DB 3DB 30 30 20 20 10 10 0 0 -10 -10 Center 2.49175 GHz 1.65 MHz/ Span 16.5 MHz Center 2.49175 GHz 1.65 MHz/ Span 16.5 MHz Date: 19.JUL.2012 08:29:14 * offset = Factor (ANT Factor+ Amp Gain + Cable Loss) [dB] = 1.9 dB (2 405 MHz) = 1.7 dB (2 480 MHz) EMC compliance Ltd. Page: 29 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr Figure 6. Plot of the Spurious RF conducted emissions Lowest Channel(2 405 MHz):30MHz~12.75GHz Lowest Channel(2 405 MHz):12.75~26.5GHz * RBW 100 kHz Marker 1 [T1 ] * RBW 100 kHz Marker 4 [T1 ] * VBW 100 kHz -38.68 dBm * VBW 100 kHz -58.00 dBm Ref 0 dBm Att 30 dB SWT 1.3 s 1.912560000 GHz Ref 0 dBm Att 30 dB SWT 1.4 s 26.390000000 GHz 0 0 Marker 1 [T1 ] -19.51 dBm A 2.395920000 GHz A -10 -10 Marker 2 [T1 ] 1 PK 1 PK 1 -42.93 dBm MAXH MAXH -20 -20 4.812720000 GHz Marker 3 [T1 ] TDF -52.52 dBm TDF -30 -30 1.429200000 GHz 1 -40 2 -40 -50 3 -50 4 3DB 3DB -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 Start 30 MHz 1.272 GHz/ Stop 12.75 GHz Start 12.75 GHz 1.375 GHz/ Stop 26.5 GHz Middle Channel(2 445 MHz):30MHz~12.75GHz Middle Channel(2 445 MHz):12.75~26.5GHz * RBW 100 kHz Marker 4 [T1 ] * RBW 100 kHz Marker 1 [T1 ] * VBW 100 kHz -53.23 dBm * VBW 100 kHz -38.36 dBm Ref 0 dBm Att 30 dB SWT 1.3 s 1.454640000 GHz Ref 0 dBm Att 30 dB SWT 1.4 s 26.362500000 GHz 0 Marker 1 [T1 ] 0 -17.55 dBm A A -10 2.446800000 GHz -10 1 Marker 2 [T1 ] 1 PK 1 PK -42.63 dBm MAXH MAXH -20 -20 4.889040000 GHz Marker 3 [T1 ] TDF -49.18 dBm TDF -30 -30 7.331280000 GHz 1 -40 2 -40 3 -50 4 -50 3DB 3DB -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 Start 30 MHz 1.272 GHz/ Stop 12.75 GHz Center 19.625 GHz 1.375 GHz/ Span 13.75 GHz Highest Channel(2 480 MHz):30MHz~12.75GHz Highest Channel(2 480 MHz):12.75~26.5GHz * RBW 100 kHz Marker 4 [T1 ] * RBW 100 kHz Marker 1 [T1 ] * VBW 100 kHz -52.54 dBm * VBW 100 kHz -38.59 dBm Ref 0 dBm Att 30 dB SWT 1.3 s 1.480080000 GHz Ref 0 dBm Att 30 dB SWT 1.4 s 25.097500000 GHz 0 Marker 1 [T1 ] 0 -15.77 dBm 2.472240000 GHz A -10 A -10 1 Marker 2 [T1 ] 1 PK -45.83 dBm 1 PK MAXH -20 4.965360000 GHz MAXH -20 Marker 3 [T1 ] -48.26 dBm TDF TDF -30 7.433040000 GHz -30 1 -40 -40 2 3 -50 4 -50 3DB 3DB -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 Center 6.39 GHz 1.272 GHz/ Span 12.72 GHz Start 12.75 GHz 1.375 GHz/ Stop 26.5 GHz Date: 19.JUL.2012 16:14:14 EMC compliance Ltd. Page: 30 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.6 Conducted Emission(N/A) 5.6.1 Regulation According to §15.207(a), for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table, as measured using a 50µH/50Ω line impedance stabilization network (LISN). Compliance with the provisions of this paragraph shall be based on the measurement of the radio frequency voltage between each power line and ground at the power terminal. The lower limit applies at the boundary between the frequency ranges. Conducted limit (dBμV) Frequency of emission (MHz) Qausi-peak Average 0.15 – 0.5 66 to 56 * 56 to 46 * 0.5 – 5 56 46 5 – 30 60 50 * Decreases with the logarithm of the frequency. According to §15.107(a), for unintentional device, except for Class A digital devices, line conducted emission limits are the same as the above table. 5.6.2 Measurement Procedure 1. The EUT was placed on a wooden table of size, 1 m by 1.5 m, raised 80 cm in which is located 40 cm away from the vertical wall and 1.5m away from the side wall of the shielded room. 2. Each current-carrying conductor of the EUT power cord was individually connected through a 50Ω/50μH LISN, which is an input transducer to a Spectrum Analyzer or an EMI/Field Intensity Meter, to the input power source. 3. Exploratory measurements were made to identify the frequency of the emission that had the highest amplitude relative to the limit by operating the EUT in a range of typical modes of operation, cable position, and with a typical system equipment configuration and arrangement. Based on the exploratory tests of the EUT, the one EUT cable configuration and arrangement and mode of operation that had produced the emission with the highest amplitude relative to the limit was selected for the final measurement. 4. The final test on all current-carrying conductors of all of the power cords to the equipment that comprises the EUT (but not the cords associated with other non-EUT equipment is the system) was then performed over the frequency range of 0.15 MHz to 30 MHz. 5. The measurements were made with the detector set to PEAK amplitude within a bandwidth of 10 kHz or to QUASI-PEAK and AVERAGE within a bandwidth of 9 kHz. The EUT was in transmitting mode during the measurements. EMC compliance Ltd. Page: 31 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 5.7 RF Exposure 5.7.1 Regulation According to §15.247(i), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission's guidelines. See § 1.1307(b)(1) of this Chapter. Limits for Maximum Permissive Exposure: RF exposure is calculated. Electric Field Magnetic Field Power Density Averaging Time Frequency Range Strength [V/m] Strength [A/m] [mW/cm2] [minute] Limits for General Population / Uncontrolled Exposure 0.3 ~ 1.34 614 1.63 *(100) 30 1.34 ~ 30 824 /f 2.19/f *(180/f2) 30 30 ~ 300 27.5 0.073 0.2 30 300 ~ 1500 / / f/1500 30 1500 ~ 15000 / / 1.0 30 f=frequency in MHz, *= plane-wave equivalent power density MPE (Maximum Permissive Exposure) Prediction Predication of MPE limit at a given distance: Equation from page 18 of OET Bulletin 65, Edition 97-01 S  PG 4R 2  R  PG 4S  2 S=power density [mW/cm ] P=Power input to antenna [mW] G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R= distance to the center of radiation of the antenna [cm] EUT: Maximum peak output power = 0.6 [mW] (=-2.24dBm) Antenna gain=2.5 (= 3.94 [dBi]) S = PG/4πR² = 100 × 3.98 / (4 × π × 400) 100 mW, at 20 cm from an antenna 6[dBi] = 0.0792 [mW/cm2] < 1.0 [mW/cm2] 0.6 mW, at 20 cm from an antenna 3.94 [dBi] S = PG/4πR²= 0.000298 [mW/cm2] < 1.0 [mW/cm2] 0.6 mW, at 2.5 cm from an antenna 3.94 [dBi] S = PG/4πR²= 0.019099[mW/cm2] < 1.0 [mW/cm2] 5.7.2 RF Exposure Compliance Issue The information should be included in the user’s manual: This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. EMC compliance Ltd. Page: 32 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.

FCC TEST REPORT Report No.: EMC-FCC-R0069 http://www.emc2000.co.kr 6. Test equipment used for test Description Manufacture Model No. Serial No. Next Cal Date. □ Temp & humidity chamber taekwang TK-04 TK001 12.12.10 □ Temp & humidity chamber taekwang TK-500 TK002 12.09.05 □ Power Meter Agilent E4416A GB41292365 12.10.26 □ Frequency Counter HP 53150A US39250565 12.09.07 □ Spectrum Analyzer Agilent E4407B US39010142 12.10.26 ■ Spectrum Analyzer R&S FSP40 100209 12.10.26 ■ Signal Generator R&S SMR40 100007 13.06.27 □ Modulation Analyzer HP 8901B 3538A05527 12.10.26 □ Audio Analyzer HP 8903B 3729A19213 12.10.28 □ AC Power Supply KIKUSUI PCR2000W GB001619 12.10.25 □ DC Power Supply Tektronix PS2520G TW50517 13.02.06 ■ DC Power Supply Tektronix PS2521G TW53135 12.10.25 □ Dummy Load BIRD 8141 7560 - □ Dummy Load BIRD 8401-025 799 - ■ EMI Test Receiver R&S ESCI 100001 13.07.10 □ Attenuator HP 8494A 2631A09825 12.10.26 □ Attenuator HP 8496A 3308A16640 12.10.26 □ Attenuator R&S RBS1000 D67079 12.10.26 □ Power sensor R&S NRP-Z81 100677 13.05.04 ■ LOOP Antenna EMCO EMCO6502 9205-2745 13.05.23 ■ BILOG Antenna Schwarzbeck VULB 9168 375 13.09.21 ■ HORN Antenna ETS 3115 00086706 13.11.21 ■ HORN Antenna ETS 3116 00086632 13.11.15 □ Power Divider Weinschel 1580-1 NX375 12.10.26 □ Power Divider Weinschel 1580-1 NX380 12.09.14 □ Power Divider Weinschel 1594 671 12.09.14 ■ Test Receiver R&S ESHS30 828765/009 12.10.28 ■ LISN R&S ENV216 101358 12.10.26 ■ LISN PMM L2-16A 0000J10705 - EMC compliance Ltd. Page: 33 of 33 480-5 Shin-dong, Yeongtong-gu, Suwon-city, Gyunggi-do, 443-390, Korea 82 31 336 9919 (Main) 82 31 336 4767 (Fax) This test report shall not be reproduced except in full, Without the written approval.


Document Created: 2012-07-30 10:07:14
Document Modified: 2012-07-30 10:07:14
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC