Test Report

FCC ID: O6RFIT1

Test Report

Download: PDF
FCCID_1111580

NVLAP Lab Code 200087-0 Application For Grant of Certification FOR Model: FIT1e P/N 010-00788-xx Low Power Transmitter FCC ID: O6RFIT1 IC: 3797A-FIT1 FOR DYNASTREAM INNOVATIONS, INC. 228 River Avenue Cochrane, Alberta T4C 2C1 Test Report Number 090419 Authorized Signatory: Scot D. Rogers Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 1 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 ROGERS LABS, INC. 4405 West 259th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214 Test Report For Application Of Certification For DYNASTREAM INNOVATIONS, INC. 228 River Avenue Cochrane, Alberta T4C 2C1 Model: FIT1e P/N 010-00788-xx Low Power Transmitter Frequency Range: 2,402-2,479 MHz FCC ID: O6RFIT1 IC: 3797A-FIT1 Test Report Number: 090419 Test Date: April 19, 2009 Authorized Signatory: Scot D. Rogers Rogers Labs, Inc. 4405 West 259th Terrace Louisburg, KS 66053 Telephone/Facsimile: (913) 837-3214 This report shall not be reproduced except in full, without the written approval of the laboratory. This report must not be used by the client to claim product endorsement by NVLAP, NIST, or any agency of the Federal Government. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 2 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Table Of Contents TABLE OF CONTENTS .................................................................................................... 3 FORWARD ....................................................................................................................... 5 APPLICABLE STANDARDS & TEST PROCEDURES .................................................... 5 OPINION / INTERPRETATION OF RESULTS ................................................................. 5 ENVIRONMENTAL CONDITIONS.................................................................................... 6 EQUIPMENT TESTED ...................................................................................................... 6 LIST OF TEST EQUIPMENT ............................................................................................ 6 2.1033(B) APPLICATION FOR CERTIFICATION ............................................................ 7 STATEMENT OF MODIFICATIONS AND DEVIATIONS ................................................. 8 EQUIPMENT AND CABLE CONFIGURATION ................................................................ 8 Test Setup .................................................................................................................................................................. 8 EQUIPMENT FUNCTION AND TESTING PROCEDURES .............................................. 8 Configuration options for the EUT ......................................................................................................................... 9 AC LINE CONDUCTED EMISSION TEST PROCEDURE ................................................ 9 Radiated Emission Test Procedure ......................................................................................................................... 9 Units of Measurements ............................................................................................................................................. 9 Test Site Locations .................................................................................................................................................... 10 SUBPART C - INTENTIONAL RADIATORS .................................................................... 10 15.203 ANTENNA REQUIREMENTS ............................................................................... 10 15.205 RESTRICTED BANDS OF OPERATION.............................................................. 10 Radiated Emissions in Restricted Bands Data per 15.205 .................................................................................... 11 Summary of Results for Radiated Emissions in Restricted Bands 15.205........................................................... 11 15.209 RADIATED EMISSIONS LIMITS; GENERAL REQUIREMENTS ......................... 12 General Radiated EMI per 15.209 .......................................................................................................................... 12 Figure One Radiated Emissions in screen room .................................................................................................... 13 Figure Two Radiated Emissions in screen room .................................................................................................... 13 Figure Three Radiated Emissions in screen room .................................................................................................. 14 Figure Four Radiated Emissions in screen room ................................................................................................... 14 Figure Five Radiated Emissions in screen room .................................................................................................... 15 Figure Six Radiated Emissions in screen room ...................................................................................................... 15 General Radiated Emissions Data per 15.209 ........................................................................................................ 16 Summary of Results for General Radiated Emissions per 15.209........................................................................ 16 Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 3 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 15.249 OPERATION IN THE BAND 2,400-2,483.5 MHZ ................................................. 16 Figure Seven output measured at temporary antenna terminal .............................................................................. 17 Figure Eight output measured at temporary antenna terminal ............................................................................... 17 Figure Nine output measured at temporary antenna terminal ................................................................................ 18 Figure Ten output measured at temporary antenna terminal .................................................................................. 18 Figure Eleven output measured at temporary antenna terminal ............................................................................. 19 Figure Twelve Occupied Bandwidth ..................................................................................................................... 19 Figure Thirteen Occupied Bandwidth .................................................................................................................... 20 Figure Fourteen Occupied Bandwidth ................................................................................................................... 20 Transmitter Radiated Emissions Data per 15.249 ................................................................................................. 21 Summary of Results for Transmitter Radiated Emissions per 15.249 ................................................................ 21 ANNEX.............................................................................................................................. 22 Annex A Measurement Uncertainty Calculations ................................................................................................. 23 Annex B Test Equipment List For Rogers Labs, Inc. ........................................................................................... 25 Annex C Rogers Qualifications ............................................................................................................................... 26 Annex D FCC Test Site Registration Letter ........................................................................................................... 27 Annex E Industry Canada Test Site Registration Letter ...................................................................................... 28 Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 4 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Forward The following information is submitted for consideration in obtaining Grant of Certification for low power intentional radiator per CFR47 Paragraph 15.249, and Industry Canada RSS-210 Low Power Transmitter, operation in the 2400 – 2483.5 MHz band. Name of Applicant: Dynastream Innovations, Inc. 228 River Avenue Cochrane, Alberta T4C 2C1 Model: FIT1e, P/N 010-00788-xx FCC ID: O6RFIT1 Industry Canada ID: 3797A-FIT1 Frequency Range: 2402-2479.0 MHz Operating Power: Less than 1 mW (as design specification, measured peak 91.9 dBμV/m @ 3 meters), for operation in the 2402-2479 MHz, Occupied band width 1,267 kHz Applicable Standards & Test Procedures In accordance with the Federal Communications Commission, Code of Federal Regulations CFR47, dated October 1, 2008, Part 2, Subpart J, Paragraphs 2.907, 2.911, 2.913, 2.925, 2.926, 2.1031 through 2.1057, applicable parts of paragraph 15, Part 15C paragraph 15.249, and Industry Canada RSS-210, the following information is submitted. Test procedures used are the established Methods of Measurement of Radio-Noise Emissions as described in the ANSI 63.4-2003 Document. Opinion / Interpretation of Results Tests Performed Results Antenna requirement per CFR47 15.203 Complies Conducted Emissions as per CFR47 15.207 Complies Radiated Emissions as per CFR47 15.209 Complies Emissions per CFR47 15.249 Complies Emissions per RSS-210 Complies Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 5 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Environmental Conditions Ambient Temperature 23.1° C Relative Humidity 34% Atmospheric Pressure 1022.4 mb Equipment Tested Equipment Serial Number FCC I.D.# FIT1e (EUT) R5-054 O6RFIT1 FIT1e (Temp Antenna Port) R5-052 (Sample #2) List of Test Equipment A Hewlett Packard 8591EM and or 8562A Spectrum Analyzer was used as the measuring device for the emissions testing. The analyzer settings used are described in the following table. Refer to the annex for a complete list of Test Equipment. HP 8591EM Spectrum Analyzer Settings Conducted Emissions RBW AVG. BW Detector Function 9 kHz 30 kHz Peak/Quasi Peak Radiated Emissions (30 – 1000 MHz) RBW AVG. BW Detector Function 120 kHz 300 kHz Peak/Quasi Peak HP 8562A Spectrum Analyzer Settings Radiated Emissions (1 – 40 GHz) RBW AVG. BW Detector Function 1 MHz 1 MHz Peak/Average Antenna Conducted Emissions RBW AVG. BW Detector Function 120 kHz 300 kHz Peak Equipment Manufacturer Model Calibration Date Due LISN Comp. Design FCC-LISN-2-MOD.CD 10/08 10/09 Antenna ARA BCD-235-B 10/08 10/09 Antenna EMCO 3147 10/08 10/09 Antenna EMCO 3143 5/08 5/09 Analyzer HP 8591EM 5/08 5/09 Analyzer HP 8562A 5/08 5/09 Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 6 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 2.1033(b) Application for Certification (1) Manufacturer: Dynastream Innovations, Inc. 228 River Avenue Cochrane, Alberta T4C 2C1 (2) Identification: FCC I.D.: O6RFIT1 IC: 3797A-FIT1 (3) Copy of the installation and operating manual: Refer to exhibit for Draft Instruction Manual. (4) Description of Circuit Functions, Device Operation: The FIT1e, P/N 010-00788-xx is a low power transmitter offering wireless communications to compliant equipment. This device features low power transmitter operation in communications frequency band of 2400-2483.5 MHz. (5) Block Diagram with Frequencies: Refer to exhibit for the Block Diagram (6) Report of measurements demonstrating compliance with the pertinent FCC/IC technical requires are provided in this report. (7) Photographs of equipment are provided in application exhibits. (8) Peripheral equipment or accessories for the equipment. No optional equipment is available for the EUT. Test samples were placed on support development (personality) boards attached to battery holder for testing. The available configuration options were investigated for this and other reports in compliance to required standards with worst- case data presented. (9) Transition Provisions of 15.37 are not being requested. (10) The equipment is not a scanning receiver. (11) The equipment is not a transmitter operating in the 59-64 GHz frequency range. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 7 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Statement of Modifications and Deviations No modifications to the EUT were required for the unit to demonstrate compliance with the FCC CFR47 Parts 15C, or RSS-210 Emissions Standards. There were no deviations to the specifications. Equipment and Cable Configuration Test Setup The FIT1e, P/N 010-00788-xx is a low power transmitter allowing short-range communications in the 2400-2483.5 MHz to compliant equipment. The unit was designed as a portable or mounted device used in the fitness industry offering end user wireless data transfer. The transmitter section allows for short-range communications to other compliant devices. The EUT was arranged as typical user equipment configurations for testing purposes. The transmitter offers no other interface connections than those in the configuration options shown below. The EUT is powered from internal replaceable batteries only and offers no provision for alternate power sources. As requested by the manufacturer and required by regulations, the unit was tested for emissions compliance using the available configurations with the worst-case data presented. Test results in this report relate only to the products described in this report. Equipment Function and Testing Procedures The EUT is a low power transmitter with transmitter operation capability in the 2402-2479 MHz frequency band (CFR47 15.249 and RSS-210). The equipment offers communications to other 2402-2479 MHz compliant devices. Two samples were offered for testing. EUT (Sample #1) was supplied for testing as a production design. Sample #2 was modified for testing purposes only replacing the integral antenna with a 50 ohm antenna port. The EUT was placed on development support PCB for testing purposes. The development PCB and battery support, provided power and set frequency of operation during testing. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 8 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Configuration options for the EUT 1. 010-00788-xx operating on development board and batteries 010-00788-XX Development PCB and AA Batteries AC Line Conducted Emission Test Procedure The equipment operates solely from direct current power and offers no provision to connect to utility AC power. Therefore, no AC power line conducted emissions testing were performed for this report. Radiated Emission Test Procedure Testing for the radiated emissions was performed as defined in sections 8.3 and 13.1 of ANSI C63.4. The EUT was arranged in the test configurations as shown above and placed on a rotating 1 x 1.5-meter wooden platform 0.8 meters above the ground plane at a distance of 3 meters from the FSM antenna. EMI energy was maximized by equipment placement, raising and lowering the FSM antenna, changing the antenna polarization, and by rotating the turntable. Each emission was maximized before final data was taken using a spectrum analyzer. Refer to photographs in exhibits for EUT placement used during testing. Units of Measurements Conducted EMI: Data is in dBµV; dB referenced to one microvolt. Radiated EMI: Data is in dBµV/m; dB/m referenced to one microvolt per meter. Radiated Emissions Calculations: Note: The limit is expressed for a measurement in dBµV/m when the measurement is taken at a distance of 3 meters. Data taken for this report was taken at a distance of 3 meters. dBµV/m @ 3m = FSM(dBµV) + A.F.(dB/m) - Amp Gain(dB) dBµV/m @ 3m = 15.8 + 33.0 – 20 = 28.8 Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 9 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Test Site Locations Conducted EMI Rogers Labs, Inc. located at 4405 W. 259th Terrace, Louisburg, KS. Radiated EMI The radiated emissions tests were performed at Rogers Labs, Inc. 3 meters Open Area Test Site (OATS) located at 4405 W. 259th Terrace, Louisburg, KS. Site Approval Refer to Annex for FCC Site Registration Letter, Reference 90910, Industry Canada Site Registration Reference 3041A-1 Subpart C - Intentional Radiators As per CFR47 Part 15, Subpart C and RSS-210 the following information is submitted for consideration in obtaining a grant of certification for unlicensed intentional radiators. 15.203 Antenna Requirements The unit is produced with a permanently attached transmitter antenna etched on the PCB module. No provisions for modification or alterations of the antenna configuration are available to the end user. For testing purposes, a second test sample was modified to allow for antenna- conducted emissions testing of transmitter for this and other compliance standards. The requirements of 15.203 are met there are no deviations or exceptions to the specification. 15.205 Restricted Bands of Operation Spurious emissions falling in the restricted frequency bands of operation were measured at the OATS. The EUT utilizes frequency, determining circuitry, which generates harmonics falling in the restricted bands. Emissions were investigated at the OATS, using appropriate antennas or pyramidal horns, amplification stages, and a spectrum analyzer. Peak and average amplitudes of frequencies above 1000 MHz were compared to the required limits with worst-case data presented below. Test procedures of ANSI 63.4-2003 paragraphs 13.1 and 8.3.1.2 were used during testing. No other significant emission was observed which fell into the restricted bands of operation. Computed emission values take into account the received radiated field strength, receive antenna correction factor, amplifier gain stage, and test system cable losses. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 10 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Radiated Emissions in Restricted Bands Data per 15.205 Emission FSM FSM Ant. Amp. RFS Horz. RFS Vert. Limit Frequency Horz. Vert. Factor Gain @ 3m @ 3m @ 3m (MHz) (dBµV) (dBµV) (dB) (dB) (dBµV/m) (dBµV/m) (dBµV/m) 2390.0 15.8 16.4 33.0 20 28.8 29.4 54.0 2400.0 16.8 17.3 33.0 20 29.8 30.3 54.0 2483.5 17.0 16.8 33.0 20 30.0 29.8 54.0 4804.0 22.6 23.3 32.9 20 35.5 36.2 54.0 4880.0 22.3 23.3 32.9 20 35.2 36.2 54.0 4958.0 23.1 23.0 32.9 20 36.0 35.9 54.0 7206.0 21.8 22.6 36.0 20 37.8 38.6 54.0 7320.0 22.6 22.6 36.4 20 39.0 39.0 54.0 7437.0 22.1 22.8 36.7 20 38.8 39.5 54.0 12010.0 23.0 23.3 40.0 20 43.0 43.3 54.0 12200.0 21.3 22.3 40.4 20 41.7 42.7 54.0 12395.0 21.5 22.3 40.6 20 42.1 42.9 54.0 Other emissions found in the restricted bands were at least 20 dB below the limits. Summary of Results for Radiated Emissions in Restricted Bands 15.205 The EUT demonstrated compliance with the radiated emissions requirements of FCC CFR47 Part 15.205 and RSS-210 restricted bands of operation. The EUT worst-case configuration demonstrated minimum margin of 10.7 dB below the FCC and RSS-210 limits. Other emissions were present with amplitudes at least 20 dB below the required limits. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 11 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 15.209 Radiated emissions limits; general requirements General Radiated EMI per 15.209 The EUT was arranged on the support development board emulating worst-case equipment configuration and operated through all of its various modes. Preliminary testing was performed in a screen room with the EUT positioned 1 meter from the FSM. Radiated emissions investigations were performed to identify the frequencies, which produced the highest emissions. Plots were made of the radiated emission frequency spectrum from 30 MHz to 18,000 MHz for preliminary transmitter testing. Refer to figures one through six the worst-case radiated emission spectrum displayed on the spectrum analyzer taken in a screen room. The each radiated emission measured was then re-maximized at the OATS site before final radiated emissions measurements were performed. Final data was taken with the EUT located at the open field test site at a distance of 3 meters between the EUT and the receiving antenna. Test procedures of ANSI 63.4-2003 paragraphs 13.1 and 8.3.1.2 were used during radiated emissions testing. The frequency spectrum from 30 MHz to 25,000 MHz was searched for radiated emissions. Peak and average amplitudes of frequencies above 1000 MHz were compared to the required limits with worst-case data presented below. Measured emission levels were maximized by EUT placement on the table, changing cable location, rotating the turntable through 360 degrees, varying the antenna height between 1 and 4 meters above the ground plane and changing antenna polarization between horizontal and vertical. Antennas used were Broadband Biconical from 30 MHz to 200 MHz, Log Periodic from 200 MHz to 5 GHz, and/or Biconilog from 30 MHz to 1000 MHz, Double-Ridge horn and/or Pyramidal Horns from 5 GHz to 25 GHz, and amplification stages. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 12 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure One Radiated Emissions in screen room Figure Two Radiated Emissions in screen room Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 13 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure Three Radiated Emissions in screen room Figure Four Radiated Emissions in screen room Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 14 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure Five Radiated Emissions in screen room Figure Six Radiated Emissions in screen room Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 15 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 General Radiated Emissions Data per 15.209 Emission FSM FSM Ant. Amp. RFS Horz. RFS Vert. Limit Freq. (MHz) Horz. Vert. Factor Gain @ 3m @ 3m @ 3m (dBµV) (dBµV) (dB) (dB) (dBµV/m) (dBµV/m) (dBµV/m) 2400.0 16.8 17.3 33.0 20 29.8 30.3 54.0 2483.5 17.0 16.8 33.0 20 30.0 29.8 54.0 Other emissions were present with amplitudes at least 20 dB below limits. Summary of Results for General Radiated Emissions per 15.209 The EUT demonstrated compliance with the radiated emissions requirements of FCC Part 15C, RSS-210 and other applicable standards for Intentional Radiators. The EUT worst-case configuration demonstrated minimum margin of 23.7 dB below the limits. Other emissions were present with amplitudes at least 20 dB below the Limits. 15.249 Operation in the Band 2,400-2,483.5 MHz The power output was measured on an open area test site @ 3 meters. Test procedures of ANSI 63.4-2003 paragraphs 13.1 and 8.3.1.2 were used during testing. The EUT was placed on a wooden turntable 0.8 meters above the ground plane and at a distance of 3 meters from the FSM antenna. The peak and quasi-peak amplitude of frequencies below 1000 MHz were measured using a spectrum analyzer. The peak and average amplitude of frequencies above 1000 MHZ were measured using a spectrum analyzer. The amplitude of the emission was then recorded from the analyzer display. Emissions radiated outside of the specified bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in 15.209, whichever is the lesser attenuation. Refer to figures seven through fourteen showing the frequency and amplitude of emission displayed on the spectrum analyzer measured at the temporary test antenna port (performed on sample #2). The amplitudes of each radiated spurious emission were measured at the OATS at a distance of 3 meters from the FSM antenna. The amplitude of each radiated spurious emission was maximized by varying the FSM antenna height, polarization, and by rotating the turntable. A Biconilog Antenna was used for measuring emissions from 30 to 1000 MHz, a Log Periodic Antenna for 200 to 5000 MHz, and Double-ridge horn and/or Pyramidal Horn Antennas from 4 GHz to 25 GHz. Emissions were measured in dBµV/m @ 3 meters. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 16 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure Seven output measured at temporary antenna terminal Figure Eight output measured at temporary antenna terminal Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 17 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure Nine output measured at temporary antenna terminal Figure Ten output measured at temporary antenna terminal Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 18 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure Eleven output measured at temporary antenna terminal Figure Twelve Occupied Bandwidth Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 19 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Figure Thirteen Occupied Bandwidth Figure Fourteen Occupied Bandwidth Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 20 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Transmitter Radiated Emissions Data per 15.249 CFS @ CFS @ CFS @ CFS @ FSM FSM FSM FSM 3m 3m 3m 3m Hor Hor Vert Vert Amp Hor Hor Vert Vert Ave Frequency Peak Ave Peak Ave AF Gain Peak Ave Peak Ave Limit 2402.0 73.3 73.3 81.0 81.0 28.1 20 81.4 81.4 89.1 89.1 94.0 4804.0 29.4 22.6 27.3 23.3 32.9 20 42.3 35.5 40.2 36.2 54.0 7206.0 29.7 21.8 27.4 22.6 36.0 20 45.7 37.8 43.4 38.6 54.0 9608.0 29.5 22.6 27.8 22.9 38.1 20 47.6 40.7 45.9 41.0 54.0 12010.0 28.4 23.0 27.4 23.3 40.0 20 48.4 43.0 47.4 43.3 54.0 2440.0 73.9 73.9 82.8 82.8 28.1 20 82.0 82.0 90.9 90.9 94.0 4880.0 29.3 22.3 28.1 23.3 32.9 20 42.2 35.2 41.0 36.2 54.0 7320.0 27.6 22.6 28.6 22.6 36.4 20 44.0 39.0 45.0 39.0 54.0 9760.0 28.1 21.5 28.0 22.8 38.3 20 46.4 39.8 46.3 41.1 54.0 12200.0 28.7 21.3 28.1 22.3 40.4 20 49.1 41.7 48.5 42.7 54.0 2479.0 73.4 73.4 83.8 83.8 28.1 20 81.5 81.5 91.9 91.9 94.0 4958.0 28.5 23.1 29.8 23.0 32.9 20 41.4 36.0 42.7 35.9 54.0 7437.0 27.6 22.1 28.4 22.8 36.7 20 44.3 38.8 45.1 39.5 54.0 9916.0 28.3 22.3 28.7 22.5 38.4 20 46.7 40.7 47.1 40.9 54.0 12395.0 27.0 21.5 27.8 22.3 40.6 20 47.6 42.1 48.4 42.9 54.0 Note: Levels measured @ 3-meter OATS site. Summary of Results for Transmitter Radiated Emissions per 15.249 The EUT demonstrated compliance with the radiated emissions requirements of FCC CFR47 Part 15.249, RSS-210 and other applicable standards for Intentional Radiators. The EUT worst- case configuration demonstrated minimum peak amplitude emission margin of 2.1 dB below the average limit. The EUT worst-case configuration demonstrated minimum radiated harmonic emission margin of 10.7 dB below the limits. No other radiated emissions were found in the restricted bands less than 20 dB below limits than those recorded in this report. Other emissions were present with amplitudes at least 20 dB below the Limits. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 21 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Annex • Annex A Measurement Uncertainty Calculations • Annex B Test Equipment List. • Annex C Rogers Qualifications. • Annex D FCC Test Site Registration Letter • Annex E Industry Canada Test Site Registration Letter Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 22 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Annex A Measurement Uncertainty Calculations Radiated Emissions Measurement Uncertainty Calculation Measurement of vertically polarized radiated field strength over the frequency range 30 MHz to 1 GHz on an open area test site at 3m and 10m includes following uncertainty: Probability Uncertainty Contribution Distribution (dB) Antenna factor calibration normal (k = 2) ±0.58 Cable loss calibration normal (k = 2) ±0.2 Receiver specification rectangular ±1.0 Antenna directivity rectangular ±0.1 Antenna factor variation with height rectangular ±2.0 Antenna factor frequency interpolation rectangular ±0.1 Measurement distance variation rectangular ±0.2 Site Imperfections rectangular ±1.5 Combined standard uncertainty uc(y) is Uc(y) = ± 1.0 2 + 0.2 2 + 1.02 + 0.12 + 2.02 + 0.12 + 0.22 + 1.52 2 2 3 Uc(y) = ± 1.6 dB It is probable that uc(y) / s(qk)> 3, where s(qk) is estimated standard deviation from a sample of n readings unless the repeatability of the EUT is particularly poor, and a coverage factor of k = 2 will ensure that the level of confidence will be approximately 95%, therefore: 1 n _ s(qk) = ------ (qk - q) 2 (n-1) ∑ k-1 U = 2 Uc(y) = 2 x ±1.6 dB = ± 3.2 dB Notes: 1.1 Uncertainties for the antenna and cable were estimated, based on a normal probability distribution with k = 2. 1.2 The receiver uncertainty was obtained from the manufacturer's specification for which a rectangular distribution was assumed. 1.3 The antenna factor uncertainty does not take account of antenna directivity. 1.4 The antenna factor varies with height and since the height was not always the same in use as when the antenna was calibrated an additional uncertainty is added. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 23 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 1.5 The uncertainty in the measurement distance is relatively small but has some effect on the received signal strength. The increase in measurement distance as the antenna height is increased is an inevitable consequence of the test method and is therefore not considered a contribution to uncertainty. 1.6 Site imperfections are difficult to quantify but may include the following contributions: -Unwanted reflections from adjacent objects. -Ground plane imperfections: reflection coefficient, flatness, and edge effects. -Losses or reflections from "transparent" cabins for the EUT or site coverings. -Earth currents in antenna cable (mainly effect biconical antennas). The specified limits for the difference between measured site attenuation and the theoretical value (± 4 dB) were not included in total since the measurement of site attenuation includes uncertainty contributions already allowed for in this budget, such as antenna factor. Conducted Measurements Uncertainty Calculation Measurement of conducted emissions over the frequency range 9 kHz to 30 MHz includes following uncertainty: Probability Uncertainty Contribution Distribution (dB) Receiver specification rectangular ±1.5 LISN coupling specification rectangular ±1.5 Cable and input attenuator calibration normal (k=2) ±0.5 Combined standard uncertainty uc(y) is Uc(y) = ± 0.5 2 + 1.52 + 1.52 2 3 Uc(y) = ± 1.2 dB As with radiated field strength uncertainty, it is probable that uc(y) / s(qk)> 3 and a coverage factor of k = 2 will suffice, therefore: U = 2 Uc(y) = 2 x ±1.2 dB = ± 2.4 dB Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 24 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Annex B Test Equipment List For Rogers Labs, Inc. The test equipment used is maintained in calibration and good operating condition. Use of this calibrated equipment ensures measurements are traceable to national standards. List of Test Equipment Calibration Date Oscilloscope Scope: Tektronix 2230 2/09 Wattmeter: Bird 43 with Load Bird 8085 2/09 Power Supplies: Sorensen SRL 20-25, SRL 40-25, DCR 150, DCR 140 2/09 H/V Power Supply: Fluke Model: 408B (SN: 573) 2/09 R.F. Generator: HP 606A 2/09 R.F. Generator: HP 8614A 2/09 R.F. Generator: HP 8640B 2/09 Spectrum Analyzer: HP 8562A, 5/08 Mixers: 11517A, 11970A, 11970K, 11970U, 11970V, 11970W HP Adapters: 11518, 11519, 11520 Spectrum Analyzer: HP 8591EM 5/08 Frequency Counter: Leader LDC825 2/09 Antenna: EMCO Biconilog Model: 3143 5/08 Antenna: EMCO Log Periodic Model: 3147 10/08 Antenna: Antenna Research Biconical Model: BCD 235 10/08 Antenna: EMCO Dipole Set 3121C 2/09 Antenna: C.D. B-101 2/09 Antenna: Solar 9229-1 & 9230-1 2/09 Antenna: EMCO 6509 2/09 Audio Oscillator: H.P. 201CD 2/09 R.F. Power Amp 65W Model: 470-A-1010 2/09 R.F. Power Amp 50W M185- 10-501 2/09 R.F. PreAmp CPPA-102 2/09 LISN 50 μHy/50 ohm/0.1 µf 10/08 LISN Compliance Eng. 240/20 2/09 LISN Fischer Custom Communications FCC-LISN-50-16-2-08 2/09 Peavey Power Amp Model: IPS 801 2/09 Power Amp A.R. Model: 10W 1010M7 2/09 Power Amp EIN Model: A301 2/09 ELGAR Model: 1751 2/09 ELGAR Model: TG 704A-3D 2/09 ESD Test Set 2010i 2/09 Fast Transient Burst Generator Model: EFT/B-101 2/09 Current Probe: Singer CP-105 2/09 Current Probe: Solar 9108-1N 2/09 Field Intensity Meter: EFM-018 2/09 KEYTEK Ecat Surge Generator 2/09 Shielded Room 5 M x 3 M x 3.0 M Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 25 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

NVLAP Lab Code 200087-0 Annex C Rogers Qualifications Scot D. Rogers, Engineer Rogers Labs, Inc. Mr. Rogers has approximately 17 years experience in the field of electronics. Six years working in the automated controls industry and 6 years working with the design, development and testing of radio communications and electronic equipment. Positions Held Systems Engineer: A/C Controls Mfg. Co., Inc. 6 Years Electrical Engineer: Rogers Consulting Labs, Inc. 5 Years Electrical Engineer: Rogers Labs, Inc. Current Educational Background 1) Bachelor of Science Degree in Electrical Engineering from Kansas State University 2) Bachelor of Science Degree in Business Administration Kansas State University 3) Several Specialized Training courses and seminars pertaining to Microprocessors and Software programming. Rogers Labs, Inc. Dynastream Innovations, Inc. FCC ID: O6RFIT1 4405 West 259th Terrace Model: FIT1e IC: 3797A-FIT1 Louisburg, KS 66053 Test #:090419 SN: R5-054 PN: 010-00788-xx Phone/Fax: (913) 837-3214 Test to: FCC CFR47 15.249, RSS 210 Page 26 of 28 Revision 1 File: TstRpt FIT1 Date: May 11, 2009

nviad FEDERAL COMMUNICATIONS COMMISSION Laboratory Division 7435 Oakland Mills Road Columbia, MD 21046 June 18, 2008 Registration Number: 90910 Rogers Labs, Inc. 4405 West 259th Terrace, Louisburg, KS 66053 Attention: Scot Rogers Re: Measurement facility located at Louisburg 3 & 10 meter site Date of Renewal: June 18, 2008 Dear Sir or Madam: Your request for renewal of the registration of the subject measurement facility has been received. The information submitted has been placed in your file and the registration has been renewed. The name of your organization will remain on the list of facilities whose measurement data will be accepted in conjunction with applications for Certification under Parts 15 or 18 of the Commssion‘s Rules. Please note that the file must be updated for any changes made to the facility and the registration must be renewed at least every three years. Measurement facilities that have indicated that they are available to the public to perform measurement services on a fee basis may be found on the FCC website wwow.fcc.gov under E—Filing, OET Equipment Authorization Electronic Filing, Test Firms. Sincerely, Phyllis P Industry Analyst

nviad NeD sts: mare July 29th, 2008 OUR FILE: 46405—3041 Submussion No: 127059 Rogers Labs Inc. 4405 West 2591 Terrace Lousburg KY 66053 USA Atiention. Scot D. Rogers Dear Sitr/Madame: The Bureau has received your application for the regastration / renewal of a 3/10m OATS. Be advised that the information received was satisfactory to Industry Canada. The following number(s) is now associated to the site(s) for which registration / renewal was sought (3040A—1). Please reference the appropniate site number in the body of test reports contaimng measurements performed on the site. In addition, please be informed that the Bureau is now utilizing a new site numbering scheme in order to simplify the electronic filing process. Our goal is to reduce the number of secondary codes associated to one particular company. The following changes have been made to your records. Your primary code is: 3041 The company number associated to the site(s) located at the above address 1is: 3041A The table below is a summary of the changes made to the unique site registration number(s): New Site Number Obsolete Site Number Description of Site Expiry Date (Y¥YYY—MM—DD) 304 1A¥—1 3041—1 3 / 10m OATS 2010—07—29 Furthermore, to obtain or renew a unmque site number, the applicant shall demonstrate that the site has been accredited to ANSI C€6S3.4—2003 or later. A scope of accreditation indicating the accreditation by a recognized accreditation body to ANSI C€63.4—2003 shall be accepted. Please indicate in a letter the previous assigned site number if applicable and the type of site (example: 3 meter OATS or 3 meter chamber). If the test facility is not accredited to ANSI C6S3.4—2003 or later, the test facility shall submit test data demonstrating full compliance with the ANSI standard. The Bureau will evaluate the filing to determine if recogmtion shall be granted. The frequency for re—validation of the test site and the information that is required to be filed or retained by the testing party shall comply with the requirements established by the accrediting organmization. However, in all cases, test site re—validation shall occur on an interval not to exceed two years. There is no fee or form associated with an OATS filing. OATS submissions are encouraged to be submitted electromcally to the Bureau using the following URL; If you have any questions, you may contact the Bureau by e—mail at certification.bureau@1ic.ge.ca Please reference our file and submission number above for all correspondence. Yours sincerely, seXe S. Proulx Wireless Laboratory Manager Certification and Engineering Bureau Industry Canada 3701 Carling Ave., Buildng 94 Ottawa, Ontario KZ2H 882 Ccanada Canada


Document Created: 2009-05-11 07:21:28
Document Modified: 2009-05-11 07:21:28
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC