Test Report (JBP)_rev 2

FCC ID: NOIKBN236

Test Report

Download: PDF
FCCID_3038216

FCC DoC Test Report Report No.: FD160413E14 Test Model: N236 Received Date: Apr. 13 , 2016 Test Date: Apr. 23 to June 07, 2016 Issued Date: June 08, 2016 Applicant: NETRONIX, INC Address: No.945,Boai St.,Jubei City,Hsin-Chu,302,Taiwan,R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. Test Location (1): E-2, No.1, Li Hsin 1st Road, Hsinchu Science Park, Hsinchu City 300, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (3): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: FD160413E14 Page No. 1 / 30 Report Format Version: 6.1.2

Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ......................................................................................................................... 4 2 Summary of Test Results......................................................................................................................... 5 2.1 Measurement Uncertainty ................................................................................................................... 5 2.2 Modification Record ............................................................................................................................ 5 3 General Information ................................................................................................................................. 6 3.1 General Description of EUT ................................................................................................................ 6 3.2 Operating Modes of EUT and Determination of Worst Case Operating Mode ................................... 7 3.3 Test Program Used and Operation Descriptions ................................................................................. 8 3.4 Primary Clock Frequencies of Internal Source ................................................................................... 8 3.5 Miscellaneous ...................................................................................................................................... 9 4 Configuration and Connections with EUT ........................................................................................... 10 4.1 Configuration of Peripheral Devices and Cable Connections ........................................................... 12 5 Conducted Emissions at Mains Ports .................................................................................................. 13 5.1 Limits ................................................................................................................................................. 13 5.2 Test Instruments ................................................................................................................................ 13 5.3 Test Arrangement .............................................................................................................................. 15 5.4 Supplementary Information ............................................................................................................... 15 5.6 Test Results (Mode1) ........................................................................................................................ 16 5.7 Test Results (Mode2) ........................................................................................................................ 18 6 Radiated Emissions up to 1 GHz .......................................................................................................... 20 6.1 Limits ................................................................................................................................................. 20 6.2 Test Instruments ................................................................................................................................ 21 6.3 Test Arrangement .............................................................................................................................. 22 6.4 Supplementary Information ............................................................................................................... 22 6.5 Test Results ....................................................................................................................................... 23 7 Radiated Emissions above 1 GHz......................................................................................................... 25 7.1 Limits ................................................................................................................................................. 25 7.2 Test Instruments ................................................................................................................................ 26 7.3 Test Arrangement .............................................................................................................................. 27 7.4 Supplementary Information ............................................................................................................... 27 7.5 Test Results ....................................................................................................................................... 28 Appendix – Information on the Testing Laboratories ................................................................................ 30 Report No.: FD160413E14 Page No. 2 / 30 Report Format Version: 6.1.2

Release Control Record Issue No. Description Date Issued FD160413E14 Original release. June 08, 2016 Report No.: FD160413E14 Page No. 3 / 30 Report Format Version: 6.1.2

1 Certificate of Conformity Product: 6 inch Electronic Display Device Brand: Kobo Test Model: N236 Sample Status: ENGINEERING SAMPLE Applicant: NETRONIX, INC Test Date: Apr. 23 to June 07, 2016 Standards: 47 CFR FCC Part 15, Subpart B, Class B ICES-003:2016 Issue 6, Class B ANSI C63.4:2014 The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. Prepared by : , Date: June 08, 2016 Wendy Wu / Specialist Approved by : , Date: June 08, 2016 Ken Lu / Manager Report No.: FD160413E14 Page No. 4 / 30 Report Format Version: 6.1.2

2 Summary of Test Results 47 CFR FCC Part 15, Subpart B / ICES—003:2016 Issue 6, Class B ANSI ©63.4:2014 FCC 1CES—003 Verdict Clause Clause Test Item Result/Remarks Minimum passing Class B margin 15.107 6.1 AC Power Line Conducted |ig .49g gB at 0.61484 MHz Pass Emissions Without AC power port of the EUT 6.21 Radiated Emissions up to 1 Minimum passing Class B margin Pass C GHz is —3.33 dB at 749.90 MHz 15109 Minimum passing Class B margin 6.2.2 Radiated Emissions above 1| is—20.11 dB at 4639.24 MHz EUT‘s Pass C GHz highest frequency is below 108 MHz Note: There is no deviation to the applied test methods and requirements covered by the scope of this report. 2.1 Measurement Uncertainty Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT: The listed uncertainties are the worst case uncertainty for the entire range of measurement. Please note that the uncertainty values are provided for informational purposes only and are not used in determining the PASS/FAIL results. Measurement Frequency ExpenczESQl)Jr(l;ertalnty Conducted Emissions at mains ports 150kHz ~ 30MHz 1.83 dB Radiated Emissions up to 1 GHz S0MHz ~ 1GHz 3.99 dB Radiated Emissions above 1 GHz Above 1GHz 3.65 dB 2.2 Modification Record There were no modifications required for compliance. Report No.: FD160413E14 Page No. 5 / 30 Report Format Version: 6.1.2

3 General Information 3.1 General Description of EUT Product 6 inch Electronic Display Device Brand Kobo Test Model N236 Sample Status ENGINEERING SAMPLE Operating Software NA Power Supply rating 3.7Vdc from battery or 5Vdc from host equipment Operating Frequency NA Accessory Device NA Data Cable Supplied USB cable (Shielded, 1m) x 1 Note: 1. The EUT must be supplied with a rechargeable battery as following table: Brand Model No. Spec. SPRINGPOWER SP 285083 DC: 3.7V, 1500mAh TECHNOLOGY 2. The antenna provided to the EUT, please refer to the following table: Frequency Ant. Gain Antenna Antenna Cable Length Brand Model range (dBi) Type Connector (mm) (GHz to GHz) Walsin Technology 2.4~2.4835 Ceramic soldering RFECA3216060AAT 2 NA Corporation GHz antenna terminal 3. The EUT incorporates a SISO function. MODULATION MODE DATA RATE (MCS) TX & RX CONFIGURATION 802.11b 1 ~ 11Mbps 1TX 1RX 802.11g 6 ~ 54Mbps 1TX 1RX 802.11n (HT20) MCS 0~7 1TX 1RX 4. When USB port is charging the rechargeable battery, the EUT has WiFi function under charging mode. And the USB port is connected to Host unit, the EUT WiFi function will be disabled. 5. The above EUT information is declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual. Report No.: FD160413E14 Page No. 6 / 30 Report Format Version: 6.1.2

3.2 Operating Modes of EUT and Determination of Worst Case Operating Mode EUT has been pre-tested under following test modes, and test mode D was the worst case for final test. Test Condition (Radiated emission) Test Mode Polarity Description Mode A X Plane Wireless Link Mode B Y Plane Wireless Link Mode C Z Plane Wireless Link Mode D X Plane USB mode Test modes are presented in the report as below. Conducted emission test Test Mode Polarity Description Mode 1 X Plane USB mode (power from host) Mode 2 X Plane USB mode (power from adapter) Radiated emission test Test Mode Polarity Description Mode 1 X Plane USB mode Report No.: FD160413E14 Page No. 7 / 30 Report Format Version: 6.1.2

3.3 Test Program Used and Operation Descriptions For Conducted/Radiated test Mode 1: 1. Turn on the power of all equipment. 2. Support unit B (Notebook Computer) runs “EMCtest..bat” program to enable all functions of EUT. 3. Support unit B (Notebook Computer) runs “EMCTEST.EXE” scrolls "H" patterns on its screen. For Conducted test Mode 2 : 1. The EUT (Battery) was recharged from adapter via one USB cable continuously. 3.4 Primary Clock Frequencies of Internal Source The EUT is a 2.4GHz WLAN device by NETRONIX, INC., for detailed internal source, please refer to the manufacturer's specifications. Report No.: FD160413E14 Page No. 8 / 30 Report Format Version: 6.1.2

3.5 Miscellaneous Labelling Requirements for Part 15 Devices:  Verification The specific labelling requirements for a device subject to the Verification procedure are contained in Section 15.19(a). These labelling requirements are: If the device is subject only to Verification, include a label bearing a unique identifier (Section 2.954) and one of three compliance statements specified in Section 15.19(a). If the labeling area for the device is so small, and/or it is not practical to place the compliance statement on the device, then the statement can be placed in the user manual or product packaging (Section 15.19(a)(5)). However, the device must still be labelled with the unique identifier (Verification). Generally, devices smaller than the palm of the hand are considered too small for the compliance statement.  Certification If the device is subject to Certification: (1) Section 2.925 contains information on identification of the equipment; (2) include a label bearing an FCC Identifier (FCC ID) (Section 2.926) and (3) include the appropriate compliance statement in Section 15.19(a). If the device is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. However, the device must still be labelled with the FCC ID. If the device is unquestionably too small for the FCC ID to be readable (smaller than 4-6 points), the FCC ID may be placed in the user manual. However, it must be determined that the device itself is too small – the label area allocated to the FCC ID may not be reduced because of over crowded identification of other product and regulatory information. An electronic display of the FCC ID (see 9. Electronic Labelling below) may be used for Certification of Section 15.212 modular transmitters and software defined radios (Section 2.944).  Declaration of Conformity (DoC): The labelling requirements for a device subject to the DoC procedure are specified in Section 15.19(b). The label should include the FCC logo along with the Trade Name and Model Number, which satisfies the unique identifier requirement of Section 2.1074 if it represents the identical equipment tested for DoC compliance. For personal computers assembled from authorized components, the following additional text must also be included: “Assembled from tested components,” “Complete system not tested.” When the device is so small and/or when it is not practical to place the required additional text on the device, the text may be placed in the user manual or pamphlet supplied to the user. However, the FCC logo, Trade Name, and Model Number must still be displayed on the device (Section 15.19(b)(3)). Part 15 Declaration of Conformity (DoC) Label Examples Equipment certified as software defined radio may use a means that readily displays the FCC ID on an electronic display screen, instead of labelling the device (Section 2.925 (e)). Further information may refer to FCC KDB:784748 D01 Labelling Part 15 &18 Guidelines Labelling Requirements for ICES-003 Devices:  Industry Canada ICES-003 Compliance Label: CAN ICES-3 (*)/NMB-3(*) * Insert either “A” or “B” but not both to identify the applicable Class of ITE. Report No.: FD160413E14 Page No. 9 / 30 Report Format Version: 6.1.2

4 Configuration and Connections with EUT For Conducted/Radiated test Mode 1: Mouse (A) 2 NOTEBOOK Micro COMPUTER (B) USB 1 EUT 4 I-Pod (D) Printer (C) 3 Report No.: FD160413E14 Page No. 10 / 30 Report Format Version: 6.1.2

For Conducted test Mode 2 : EUT Battery(3.7V) 1 USB Port (1) {A) Adapter T T Report No.: FD160413E14 Page No. 11 / 30 Report Format Version: 6.1.2

4.1 Configuration of Peripheral Devices and Cable Connections For conducted test mode 2 ID Product Brand Model No. Serial No. FCC ID Remarks A. USB ADAPTER ASUS EXA1205UA NA NA Provided by Lab Note: 1. All power cords of the above support units are non-shielded (1.8m). Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. USB 1 1 Yes 0 Supplied by client For other test items ID Product Brand Model No. Serial No. FCC ID Remarks A. Mouse DELL FCC DoC Provided by Lab MOC5UO l1401MMP NOTEBOOK B. DELL PP32LA HSLB32S FCC DoC Provided by Lab COMPUTER C. Printer EPSON LQ-300+II G88Y074083 FCC DoC Provided by Lab D. I-Pod Apple MD778TA/A CC4JMH7LF4T1 NA Provided by Lab Note: 1. All power cords of the above support units are non-shielded (1.8m). Shielding ID Descriptions Qty. Length (m) Cores (Qty.) Remarks (Yes/No) 1. USB 1 1 YES 2 Supplied by Client 2. USB 1 1.8 YES 1 Provided by Lab 3. USB 1 1.8 YES 0 Provided by Lab 4. USB 1 0.1 YES 0 Provided by Lab Note: 1.All power cords of the above support units are non-shielded (1.8m). Report No.: FD160413E14 Page No. 12 / 30 Report Format Version: 6.1.2

5 Conducted Emissions at Mains Ports 5.1 Limits Class A (dBuV) Class B (dBuV) Frequency (MHz) Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50 Notes: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases linearly with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 5.2 Test Instruments For test Mode 1: DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver ESCS 30 100375 May 06, 2015 May 05, 2016 R&S Line-Impedance Stabilization Network NSLK-8127 8127-522 Sep. 01, 2015 Aug. 31, 2016 (for EUT) SCHWARZBECK Line-Impedance Stabilization Network ENV216 100072 June 11, 2015 June 10, 2016 (for Peripheral ) R&S RF Cable 5D-FB COCCAB-001 Mar. 08, 2016 Mar. 07, 2017 50 ohms Terminator N/A EMC-03 Sep. 23, 2015 Sep. 22, 2016 50 ohms Terminator N/A EMC-02 Oct. 01, 2015 Sep. 30, 2016 50 ohms Terminator E1-011315 13 Dec. 11, 2015 Dec. 10, 2016 Software BVADT_Cond_ NA NA NA BVADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. C. 3 The VCCI Con C Registration No. is C-3611. 4 Tested Date: Apr. 23, 2016 Report No.: FD160413E14 Page No. 13 / 30 Report Format Version: 6.1.2

For test Mode 2: DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver ESCS 30 100375 May 09, 2016 May 08, 2017 R&S Line-Impedance Stabilization Network NSLK-8127 8127-522 Sep. 01, 2015 Aug. 31, 2016 (for EUT) SCHWARZBECK Line-Impedance Stabilization Network ENV216 100072 June 11, 2015 June 10, 2016 (for Peripheral ) R&S RF Cable 5D-FB COCCAB-001 Mar. 08, 2016 Mar. 07, 2017 10 dB PAD HAT-10+ CONATT-002 Sep. 14, 2015 Sep. 13, 2016 Mini-Circuits 50 ohms Terminator N/A EMC-03 Sep. 23, 2015 Sep. 22, 2016 50 ohms Terminator N/A EMC-02 Oct. 01, 2015 Sep. 30, 2016 50 ohms Terminator E1-011315 13 Dec. 11 2015 Dec. 10 2016 Software BVADT_Cond_ NA NA NA BVADT V7.3.7.3 Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. C. 3 The VCCI Con C Registration No. is C-3611. 4 Tested Date:June 07, 2016 Report No.: FD160413E14 Page No. 14 / 30 Report Format Version: 6.1.2

5.3 Test Arrangement a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The test results of conducted emissions at mains ports are recorded of six worst margins for quasi-peak (mandatory) [and average (if necessary)] values against the limits at frequencies of interest unless the margin is 20 dB or greater. Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP) and average detection (AV) at frequency 0.15MHz-30MHz. For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 5.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FD160413E14 Page No. 15 / 30 Report Format Version: 6.1.2

5.6 Test Results (Mode1) Frequency Range 150kHz ~ 30MHz geéZit:Jv;L::ctlon S:;S;;e(fvg(!}ggljz :’s‘s::em""er 120Vac, 60Hz Conamone"""! |25to, rewRH Tested by Jason Huang Test Mode Mode 1 Phase Of Power : Line (L) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.71641 10.26 18.99 11.97 29.25 22.23 56.00 46.00 —26.75 —23.77 2 0.81016 10.25 18.47 1242 28.72 22.67 56.00 46.00 —27.28 —23.33 3 1.39844 10.24 14.42 7.55 24.66 17.79 56.00 46.00 —31.34 —28.21 4 2.35547 10.29 19.92 8.11 30.21 18.40 56.00 46.00 —25.79 —27.60 5 10.96875 10.59 13.23 7.23 23.82 17.82 60.00 50.00 —36.18 —32.18 6 17.55078 10.87 15.09 10.87 25.96 21.74 60.00 50.00 —34.04 —28.26 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value agay 1 100 so so ro so so ao 2o 10‘be s0i00 mane Report No.: FD160413E14 Page No. 16 / 30 Report Format Version: 6.1.2

Frequency Range 150kHz ~ 30MHz geéZi‘:Jv;L::c"on S:;S;;e(i(vg(?:gljz :’s‘s:t‘em""e’ 120Vac, 60Hz Conamone"""! |25‘c, rewRH Tested by Jason Huang Test Mode Mode 1 Phase Of Power : Neutral (N) Frequency Correction Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.74766 10.25 18.56 7.36 28.81 17.61 56.00 46.00 —27.19 —28.39 2 0.95078 10.22 19.94 6.53 30.16 16.75 56.00 46.00 —25.84 —29.25 3 243750 10.30 18.87 6.16 29.17 16.46 56.00 46.00 —26.83 —29.54 4 2.78516 10.33 20.97 7.31 31.30 17.64 56.00 46.00 —24.70 —28.36 5 8.85156 10.53 19.32 5.28 29.85 15.81 60.00 50.00 —30.15 —34.19 6 28.76563 11.20 11.83 0.78 23.03 11.98 60.00 50.00 —36.97 —38.02 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value aBuy t10 100 so so ro so so «o so ols 160 t0‘b 2000 mne Report No.: FD160413E14 Page No. 17 / 30 Report Format Version: 6.1.2

5.7 Test Results (Mode?2) Frequency Range 150kHz ~ 30MHz geéZit:Jv;L::ctlon S:;S;;e(fvg(!}ggljz Input Power 120Vac, 60Hz Eg‘r’l';‘i"?o':‘;"‘"" 25°C, 68%RH Tested by Arthur Yang Test Mode Mode 2 Phase Of Power : Line (L) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. a.P. AV. 1 0.15391 10.44 43.34 37.25 58.78 47.69 65.79 55.79 —12.01 —8.10 2 0.23594 10.41 38.82 28.09 49.23 38.50 6224 5224 —13.01 —13.74 3 0.61484 10.41 38.22 31.44 48.63 41.85 56.00 46.00 —7.37 —4.15 4 0.61484 10.41 37.94 31.53 48.35 41.94 56.00 46.00 —7.65 —4.06 5 0.70078 10.40 3544 19.84 45.84 30.24 56.00 46.00 —10.16 —15.76 6 0.91172 10.39 29.61 17.68 40.00 28.07 56.00 46.00 —16.00 —17.93 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value apav 10 100 so so zo so so ao so z0 10 ® 10be s 1ho mave Report No.: FD160413E14 Page No. 18 / 30 Report Format Version: 6.1.2

Frequency Range 150kHz ~ 30MHz geéZi‘:Jv;L::c"on S:;S;;e(i(vg(?:gljz Input Power 120Vac, 60Hz Eg‘r’l':i’t?o':‘;""‘" 25°C, 68%RH Tested by Arthur Yang Test Mode Mode 2 Phase Of Power : Neutral (N) Frequency |Correction| Reading Value Emission Level Limit Margin No Factor (dBuV) (dBuV) (dBuV) (dB) (MHz) (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.15391 10.45 41.87 28.89 52.32 39.34 65.79 55.79 —18.47 —16.45 2 0.23203 10.45 39.88 29.56 50.33 40.01 62.38 52.38 —12.05 —12.37 3 0.46250 10.47 29.30 19.98 39.77 30.45 56.65 46.65 —16.88 —16.20 4 0.60703 10.46 80.33 11.19 40.79 21.65 56.00 46.00 —15.21 —24.35 5 0.68906 10.46 31.07 20.20 41.53 30.66 56.00 46.00 —14.47 —15.34 6 1.46094 10.46 28.56 13.86 39.02 24.32 56.00 46.00 —16.98 —21.68 Remarks: 1. Q.P. and AV. are abbreviations of quasi—peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level — Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value amuv 110 100 so so to so so a zo zm 10 ®—, + ols 1b 10b0 30 bo mane Report No.: FD160413E14 Page No. 19 / 30 Report Format Version: 6.1.2

6 Radiated Emissions up to 1 GHz 6.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 39 29.5 88-216 43.5 33.1 40 30 216-230 46.4 35.6 230-960 47 37 960-1000 49.5 43.5 Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 30-88 49.5 40 88-216 54 43.5 50.5 40.5 216-230 56.9 46 230-960 57.5 47.5 960-1000 60 54 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. QP detector shall be applied if not specified. Report No.: FD160413E14 Page No. 20 / 30 Report Format Version: 6.1.2

6.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010125 Apr. 16, 2016 Apr. 15, 2017 Agilent N9038A MY50010132 July 04, 2015 July 03, 2016 Pre-Amplifier 310N 352925 Aug. 30, 2015 Aug. 29, 2016 Sonoma 310N 352926 Aug. 30, 2015 Aug. 29, 2016 Trilog Broadband VULB 9168 9168-359 Jan. 05, 2016 Jan. 04, 2017 Antenna VULB 9168 9168-358 Jan. 05, 2016 Jan. 04, 2017 SCHWARZBECK Fixed attenuator UNAT-5+ CHF-001 Sep. 10, 2015 Sep. 09, 2016 Mini-Circuits UNAT-5+ CHF-002 Sep. 10, 2015 Sep. 09, 2016 CHFCAB-001-1 CHFCAB-001-3 Sep. 23, 2015 Sep. 22, 2016 CHFCAB-001-4 RF Cable 8D-FB CHFCAB-002-1 CHFCAB-002-3 Sep. 23, 2015 Sep. 22, 2016 CHFCAB-002-4 Software ADT_Radiated_V NA NA NA BVADT 8.7.07 Antenna Tower & Turn Table NA NA NA NA CT Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in 10m Chamber No. F. 3. The FCC Site Registration No. is 928149. 4. The VCCI Site Registration No. is R-3252 5. The CANADA Site Registration No. is IC 7450H-1. 6. Tested Date:Apr. 26, 2016 Report No.: FD160413E14 Page No. 21 / 30 Report Format Version: 6.1.2

6.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited test facility. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is up to 1 GHz. Note: The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for quasi-peak detection (QP) at frequency up to 1GHz. For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration. 6.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FD160413E14 Page No. 22 / 30 Report Format Version: 6.1.2

6.5 Test Results Detector Function & . Frequency Range 30MHz 1GHz Bandwidth Quasi—Peak (QP), 120kHz Input Power 5Vde from host equipment Eg\rl]';ci)“lmn:mal 25°C, 63%RH Tested by Wythe Lin Test Mode Mode 1 Antenna Polarity & Test Distance : Horizontal at 10 m Emission mas . Antenna Table Raw Correction No Fr?,\‘jlllj_'ezr;cy Level ( dIB;:Jn\}I}m) M(z'é’)' n Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 33.57 20.34 QP 30.00 —9.66 4.00 H 28 3$4.10 —13.76 2 270.90 30.32 QP 37.00 —6.68 3.00 H 225 42.81 —12.49 3 421.30 27.63 QP 37.00 —9.37 2.00 H 359 35.85 —8.22 4 489.85 30.69 QP 37.00 —6.31 2.00 H 90 37.47 —6.78 5 661.30 33.31 QP 37.00 —3.69 1.00 H 62 36.65 —8.34 6 748.65 30.49 QP 37.00 —6.51 1.00 H 212 3219 —1.70 Remarks: 1. Emission Level{dBuV/m)= Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBuUim} 80 — 70 80 5o 40 30 20 i i i i i i i i i 1 30 100 200 300 400 500 500 700 800 200 1000 Frequency (MHz) Report No.: FD160413E14 Page No. 23 / 30 Report Format Version: 6.1.2

Frequency Range |30MHz ~ 1GHz gs:}z‘f;‘i";ti“”"“°” * quasi—Peak (QP), 120kHz Input Power 5Vde from host equipment Eg\r']';ci)“lmn:mal 25°C, 63%RH Tested by Wythe Lin Test Mode Mode 1 Antenna Polarity & Test Distance : Vertical at 10 m Emission mas . Antenna Table Raw Correction No Frml:_'ezr;cy Level ( dIB;:Jn\}I}m) M(z'é’)'n Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 49.50 23.17 OP 30.00 —6.83 1.00 V 3 35.73 —12.56 2 177.32 25.67 aP 30.00 ~4.33 2.00 V 100 39.08 —13.41 3 238.02 26.05 QP 37.00 —10.95 2.00 V 202 39.87 —13.82 4 492.95 26.76 QP 37.00 —10.24 1.00 V 181 33.15 —6.39 5 662.74 24.11 QP 37.00 —12.89 4.00 V 264 27.05 —2.94 6 749.90 33.67 QP 37.00 —3.33 3.00 V 204 34.87 —1.20 Remarks: 1. Emission Level{dBuV/m)= Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBu¥im} 80 — 70 80 50 40 30— 20 10 0 a0— i i i i i i i i i i 30 100 200 300 400 500 500 700 800 800 1000 Frequency (MHz) Report No.: FD160413E14 Page No. 24 / 30 Report Format Version: 6.1.2

7 Radiated Emissions above 1 GHz 7.1 Limits Emissions radiated outside of the specified bands, shall be according to the general radiated limits as following: Radiated Emissions Limits at 10 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B 1000-3000 Avg: 49.5 Avg: 43.5 Not defined Not defined Above 3000 Peak: 69.5 Peak: 63.5 Not defined Not defined Radiated Emissions Limits at 3 meters (dBμV/m) Frequencies FCC 15B / ICES-003, FCC 15B / ICES-003, CISPR 22, Class A CISPR 22, Class B (MHz) Class A Class B Avg: 56 Avg: 50 1000-3000 Avg: 60 Avg: 54 Peak: 76 Peak: 70 Peak: 80 Peak: 74 Avg: 60 Avg: 54 Above 3000 Peak: 80 Peak: 74 Notes: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. Frequency Range (For unintentional radiators) Highest frequency generated or used in the device or Upper frequency of measurement range (MHz) on which the device operates or tunes (MHz) Below 1.705 30 1.705-108 1000 108-500 2000 500-1000 5000 5th harmonic of the highest frequency or 40GHz, Above 1000 whichever is lower Report No.: FD160413E14 Page No. 25 / 30 Report Format Version: 6.1.2

7.2 Test Instruments DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Test Receiver N9038A MY50010125 Apr. 16, 2016 Apr. 15, 2017 Agilent Pre-Amplifier 8449B 3008A01975 Feb. 27, 2016 Feb. 26, 2017 Agilent Horn Antenna BBHA 9120D D123 Jan. 18, 2016 Jan. 17, 2017 SCHWARZBECK RF-104-209 RF Cable SUCOFLEX104 Dec. 10, 2015 Dec.09, 2016 RF-104-110 RF Cable 104 RF cable 131221 Dec. 10, 2015 Dec.09, 2016 Software ADT_Radiated_ NA NA NA BVADT V8.7.07 Antenna Tower & Turn Table NA NA NA NA CT Note: 1. The calibration interval of the above test instruments are 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in 10m Chamber No. F. 3. The VCCI Site Registration No. is G-136. 4. The 3dB beamwidth of the horn antenna is minimum 30 degree (or w = 1.6m at 3m distance) for 1~6 GHz. 5. Tested Date:Apr. 26. 2016 Report No.: FD160413E14 Page No. 26 / 30 Report Format Version: 6.1.2

7.3 Test Arrangement a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at an accredited chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna can be varied from one meter to four meters, the height of adjustment depends on the EUT height and the antenna 3dB beamwidth both, to detect the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The spectrum analyzer system was set to peak and average detect function and specified bandwidth with maximum hold mode when the test frequency is above 1 GHz. Note: The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection (PK) at frequency above 1GHz. The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz for Average detection (AV) at frequency above 1GHz. Ant. Tower 1 - 4m Variable EUT& 3m Support Units Turn Table Absorber 80cm Ground Plane Test Receiver 7.4 Supplementary Information There is not any deviation from the test standards for the test method. Report No.: FD160413E14 Page No. 27 / 30 Report Format Version: 6.1.2

7.5 Test Results L Detector Function & Peak (PK) / Frequency Range 1GHz~12.5GHz Bandwidth Average (AV), 1MHz . Environmental s o Input Power 5Vde from host equipment Conditions 26°C, 65%RH Tested by Wythe Lin Test Mode Mode 1 Antenna Polarity & Test Distance : Horizontal at 3 m Frequency Emission Limit Margin Antgnna Table Raw Correction No (MHz) Level (dBuV/m) (dB) Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1200.52 48.37 PK 70.00 —21.63 1.00 H 118 51.61 —8.24 2 1200.52 25.36 AV 50.00 —24.64 1.00 H 118 28.60 —8.24 3 1597.10 45.932 PK 70.00 —24.68 1.00 H 101 46.75 —1.43 4 1597.10 26.55 AV 50.00 —23.45 1.00 H 101 27.98 —1.43 5 1793.32 43.14 PK 70.00 —26.86 1.00 H 97 43.45 —0.31 6 1793.32 26.89 AV 50.00 —23.11 1.00 H 97 27.20 —0.31 7 2000.52 46.71 PK 70.00 —23.29 1.00 H 165 46.11 0.60 8 2000.52 27.42 AV 50.00 —22.58 1.00 H 165 26.82 0.60 9 $326.11 43.53 PK 74.00 —30.47 1.00 H 162 38.32 5.21 10 $326.11 29.26 AV 54.00 —24.74 1.00 H 162 24.05 5.21 11 4639.24 46.71 PK 74.00 —27.29 1.00 H 157 36.92 9.79 12 4639.24 33.89 AV 54.00 —20.11 1.00 H 157 24.10 9.79 Remarks: 1. Emission Level{dBuV/m)= Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBu¥im} 80— 50 7o PEEPEERETERERRRERRRRERREceeeco 60 s _4 PEEREERETREEEEERERTEREReeeecmo a0 ; 30 20 10 o— i i i i i i i i i i i 1000 1500 2000 2500 2000 3500 4000 4500 $000 5500 £000 Frequency (MHz) Report No.: FD160413E14 Page No. 28 / 30 Report Format Version: 6.1.2

Detector Function & Peak (PK) / Frequency Range 1GHz~12.5GHz Bandwidth Averafge ()AV), 1MHz . Environmental s o Input Power 5Vde from host equipment Conditions 26°C, 65%RH Tested by Wythe Lin Test Mode Mode 1 Antenna Polarity & Test Distance : Vertical at 3 m Frequency Emission Limit Margin Antgnna Table Raw Correction No (MHz2) Level (dBuV/m) (dB) Height Angle Value Factor (dBuV/m) (m) (Degree) (dBuV) (dB/m) 1 1198.35 47.34 PK 70.00 —22.66 1.00 V 321 50.61 —8.27 2 1198.35 28.90 AV 50.00 —21.10 1.00 V 321 $2.17 —8.27 3 1400.72 43.34 PK 70.00 —26.66 1.00 V 16 45.65 —2.31 4 1400.72 26.23 AV 50.00 —23.77 1.00 V 16 28.54 —2.31 5 1599.41 46.11 PK 70.00 —23.89 1.00 V 158 47.52 1.41 6 1599.41 26.76 AV 50.00 —23.24 1.00 V 158 28.17 1.41 7 1990.47 49.21 PK 70.00 —20.79 1.00 V 25 48.66 0.55 8 1990.47 29.54 AV 50.00 —20.46 1.00 V 25 28.99 0.55 9 4000.37 44.54 PK 74.00 —29.46 1.00 V 189 36.76 7.78 10 4000.37 31.72 AV 54.00 —22.28 1.00 V 189 23.94 7.78 11 4683.13 45.13 PK 74.00 —28.87 1.00 V 118 35.26 9.87 12 4683.13 $2.46 AV 54.00 —21.54 1.00 V 118 22.59 9.87 Remarks: 1. Emission Level{dBuV/m)= Raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (dB/m) + Cable Factor (dB) — Pre—Amplifier Factor (dB) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level — Limit value Level (dBuim) 90— 80 zo PPPPEERETEERRRRRRRRRRTRERcEEEEH 50 s 4 ls d i d 30 20 10 o— i i i i i i i i i i i 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency (MHz) Report No.: FD160413E14 Page No. 29 / 30 Report Format Version: 6.1.2

Appendix – Information on the Testing Laboratories We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025. If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab Hsin Chu EMC/RF/Telecom Lab Tel: 886-2-26052180 Tel: 886-3-6668565 Fax: 886-2-26051924 Fax: 886-3-6668323 Hwa Ya EMC/RF/Safety Lab Tel: 886-3-3183232 Fax: 886-3-3270892 Email: service.adt@tw.bureauveritas.com Web Site: www.bureauveritas-adt.com The address and road map of all our labs can be found in our web site also. --- END --- Report No.: FD160413E14 Page No. 30 / 30 Report Format Version: 6.1.2


Document Created: 2019-11-16 10:37:44
Document Modified: 2019-11-16 10:37:44
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC