SZEM1609008050RG_V2

FCC ID: N7NHL8548

Test Report

Download: PDF
FCCID_3212039

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M—10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Report No.: SZEM1609008050RG Email: ee.shenzhen@sgs.com Page: 1 of 26 FCC&IC REPORT Application No: SZEM1609008050RG Applicant: Sierra Wireless Inc. Product Name: Wireless Module Mode No.(EUT): HL8548 Standards: 47 CFR Part 2 (2015) 47 CFR Part 22 subpart H (2015) 47 CFR Part 24 subpart E (2015) RSS—132 Issue 3 January 2013 RSS—133 Issue 6 January 2013 RSS—Gen Issue 4 Nov 2014 Test Method: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 RSS—132 RSS—133 RSS—Gen Issue 4 Date of Receipt: 2016—09—24 Date of Test: 2016—09—26 to 2016—09—30 Date of Issue: 2016—11—03 Test Result : PASS * * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Authorized Signature: DMW{L a w% Derek Yang Wireless Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. "This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sqs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sqs.com/terms e—document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company‘s findings at the time of its intervention only and within the limits of Client‘s instructions, if any. The Company‘s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only."

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 2 of 26 Version Revision Record Version Chapter Date Modifier Remark 00 2016-09-30 Original Add test data for 01 2016-11-03 conducted power and bandwidth. Authorized for issue by: Tested By 2016-09-26 (Mike Hu) /Project Engineer Date Prepared By 2016-09-30 (Hedy Wen) /Clerk Date Checked By 2016-11-03 (Jim Huang) /Reviewer Date “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 3 of 26 2 Test Summary FCC Test Item Requirements Test Result Rule No. Effective §2.1046, (Isotropic) FCC: ERP ≤7 W. §22.913, PASS Radiated Power EIRP ≤ 2 W. Output Data §24.232 Peak-Average §24.232 ≤13dB PASS Ratio Modulation §2.1047 Digital modulation PASS Characteristics §2.1049(h), OBW:No limit Bandwidth §22.917, PASS EBW: No limit §24.238 §2.1051, ≤ -13dBm/1%*EBW, in 1 MHz bands Band Edge immediately outside and adjacent to the §22.917, frequency block. PASS Compliance §24.238 Spurious §2.1051, FCC: ≤ -13dBm/100 kHz, from 9 kHz to emissions at §22.917, 10th harmonics but outside authorized PASS antenna terminals §24.238 operating frequency ranges. §2.1051, Field strength of §22.917, FCC: ≤ -13dBm/100 kHz, PASS spurious radiation §24.238 §2.1055, Frequency §22.355, ≤ ±2.5ppm. PASS stability §24.235 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 4 of 26 IC Test Item Requirements Result Rule No. GSM 850, WCDMA 850(Band V) Conducted output RSS-132 clause 5.4 RSS-Gen Issue 4 PASS power SRSP503 clause 5.1.3 Effective Radiated Power RSS-132 clause 5.4 RSS-Gen Issue 4 PASS of SRSP503 clause 5.1.3 Transmitter(ERP) 99% Occupied N/A RSS-Gen Issue 4 PASS Bandwidth Band Edge at RSS-132 clause 5.5 RSS-132 clause 4.5 PASS antenna terminals Spurious RSS-132 clause 5.5 emissions at RSS-Gen Issue 4 PASS antenna terminals Field strength of RSS-132 clause 5.5 RSS-Gen Issue 4 PASS spurious radiation Frequency RSS-132 clause 5.3 RSS-Gen Issue 4 PASS stability GSM 1900,WCDMA 1900 (Band II) Conducted output RSS-133 clause 6.4 RSS-Gen Issue 4 PASS power SRSP510 clause 5.1.2 Effective Radiated Power RSS-133 clause 6.4 RSS-Gen Issue 4 PASS of SRSP510 clause 5.1.2 Transmitter(EIRP) 99% Occupied N/A RSS-Gen Issue 4 PASS Bandwidth Band Edge at RSS-133 clause 6.5 RSS-133 clause 6.5 PASS antenna terminals Spurious emissions at RSS-133 clause 6.5 RSS-Gen Issue 4 PASS antenna terminals Field strength of RSS-133 clause 6.5 RSS-Gen Issue 4 PASS spurious radiation Frequency RSS-133 clause 6.3 RSS-Gen Issue 4 PASS stability “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 5 of 26 3 Content Page 1 COVER PAGE ............................................................................................................................................... 1 2 TEST SUMMARY .......................................................................................................................................... 3 3 CONTENT ...................................................................................................................................................... 5 4 GENERAL INFORMATION .......................................................................................................................... 6 4.1 CLIENT INFORMATION .............................................................................................................................. 6 4.2 GENERAL DESCRIPTION OF EUT ............................................................................................................. 6 4.3 TEST MODE ............................................................................................................................................. 6 4.4 TEST ENVIRONMENT ................................................................................................................................ 6 4.5 TEST FREQUENCY ................................................................................................................................... 7 4.6 TEST LOCATION....................................................................................................................................... 7 4.7 TEST FACILITY ......................................................................................................................................... 8 4.8 DEVIATION FROM STANDARDS ................................................................................................................. 8 4.9 ABNORMALITIES FROM STANDARD CONDITIONS....................................................................................... 8 4.10 OTHER INFORMATION REQUESTED BY THE CUSTOMER............................................................................ 8 4.11 TECHNICAL SPECIFICATION...................................................................................................................... 9 5 DESCRIPTION OF TESTS ........................................................................................................................ 10 5.1 CONDUCTED OUTPUT POWER............................................................................................................... 10 5.2 EFFECTIVE (ISOTROPIC) RADIATED POWER OF TRANSMITTER ............................................................... 10 5.3 OCCUPIED BANDWIDTH ......................................................................................................................... 11 5.4 BAND EDGE AT ANTENNA TERMINALS .................................................................................................... 12 5.5 SPURIOUS AND HARMONIC EMISSIONS AT ANTENNA TERMINAL ............................................................. 12 5.6 PEAK-AVERAGE RATIO .......................................................................................................................... 13 5.7 FIELD STRENGTH OF SPURIOUS RADIATION........................................................................................... 13 5.8 FREQUENCY STABILITY / TEMPERATURE VARIATION .............................................................................. 14 5.9 TEST SETUPS ........................................................................................................................................ 16 5.9.1 Test Setup 1 ................................................................................................................................... 16 5.9.2 Test Setup 2 ................................................................................................................................... 17 5.9.3 Test Setup 3 ................................................................................................................................... 18 5.9.4 Test Setup 4 ................................................................................................................................... 19 5.10 TEST CONDITIONS ................................................................................................................................. 20 6 MAIN TEST INSTRUMENTS ..................................................................................................................... 22 7 MEASUREMENT UNCERTAINTY ............................................................................................................ 25 8 PHOTOGRAPHS - EUT TEST SETUP..................................................................................................... 26 9 PHOTOGRAPHS - EUT CONSTRUCTIONAL DETAILS ....................................................................... 26 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 6 of 26 4 General Information 4.1 Client Information Applicant: Sierra Wireless Inc. Address of Applicant: 13811 Wireless Way Richmond, British Columbia, Canada, V6V 3A4. 4.2 General Description of EUT Product Name: Wireless Module Model No.: HL8548 Sample Type: Mobile production Antenna Type: External antenna Antenna Gain: GSM 850:1.4dBi, GSM 1900: 1.35dBi, WCDMA B2: 1.35dBi,, WCDMA B5:1.4dBi Battery: DC main: 3.7V 4.3 Test Mode Test Mode Test Modes Description GSM/TM1 GSM system, GSM/GPRS/EGPRS, GMSK modulation GSM/TM2 GSM system, EGPRS, 8PSK modulation UMTS/TM1 UMTS system, WCDMA, QPSK modulation NOTE: The test mode(s) are selected according to relevant radio technology specifications. 4.4 Test Environment Environment Parameter Selected Values During Tests Relative Humidity 52% Atmospheric Pressure: 1025Pa Temperature TN 25 °C VL 3.2V Voltage : VN 3.7V VH 4.5V NOTE: VL= lower extreme test voltage VN= nominal voltage VH= upper extreme test voltage TN= normal temperature “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 7 of 26 4.5 Test Frequency RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 128 Channel 190 Channel 251 TX 824.2MHz 836.6MHz 848.8MHz GSM850 Channel 128 Channel 190 Channel 251 RX 869.2MHz 881.6MHz 893.8MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 512 Channel 661 Channel 810 TX 1850.2MHz 1880.0MHz 1909.8MHz GSM1900 Channel 512 Channel 661 Channel 810 RX 1930.2 MHz 1960.0 MHz 1989.8 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 4132 Channel 4183 Channel 4233 TX 826.4MHz 836.6MHz 846.6MHz WCDMA BAND 5 Channel 4357 Channel 4407 Channel 4458 RX 871.4 MHz 881.6 MHz 891.6 MHz RF Channel Test Mode TX / RX Low (L) Middle (M) High (H) Channel 9262 Channel 9400 Channel 9538 TX 1852.4MHz 1880MHz 1907.6MHz WCDMA BAND 2 Channel 9662 Channel 9800 Channel 9938 RX 1932.4 MHz 1960 MHz 1987.6 MHz 4.6 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch E&E Lab, No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 8 of 26 4.7 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 10m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-823, R-4188, T-1153 and C-2383 respectively. • FCC – Registration No.: 556682 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.: 556682. • Industry Canada (IC) Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1, 4620C-2, 4620C-3. 4.8 Deviation from Standards None. 4.9 Abnormalities from Standard Conditions None. 4.10 Other Information Requested by the Customer None. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 9 of 26 4.11Technical Specification Characteristics Description GSM Radio System Type UMTS Transmission (TX): 824 to 849 MHz GSM850 Receiving (RX): 869 to 894 MHz Transmission (TX): 1850 to 1910 MHz Supported Frequency Range GSM1900 Receiving (RX): 1930 to 1990 MHz Transmission (TX): 824 to 849 MHz UMTS 850 Receiving (RX): 869 to 894 MHz Transmission (TX): 1850 to 1910 MHz UMTS 1900 Receiving (RX): 1930 to 1990 MHz GSM850: 33dBm GSM1900: 30dBm Target TX Output Power UMTS 850: 23dBm UMTS 1900: 23dBm GSM system: 200 kHz Supported Channel Bandwidth UMTS system: 5 MHz GPRS850: 241KGXW GPRS(4slots)850: 240KGXW EGPRS850: 243KG7W GPRS1900 243KGXW Designation of Emissions GPRS(4slots)1900: 243KGXW (Note: the necessary bandwidth of which is the worst value from the EGPRS1900: 244KG7W measured occupied bandwidths for UMTS850: 4M07F9W each type of channel bandwidth HSDPA850 4M07F9W configuration.) HSUPA850 4M07F9W UMTS1900: 4M07F9W HSDPA1900 4M08F9W HSUPA1900 4M08F9W “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 10 of 26 5 Description of Tests 5.1 Conducted Output Power Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The transmitter output was connected to a calibrated coaxial cable, attenuator and power meter, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The power output at the transmitter antenna port was determined by adding the value of the cable insertion loss to the power reading. The tests were performed at three frequencies (low channel, middle channel and high channel) and on the highest power levels, which can be setup on the transmitters. Note: Reference test setup 1 5.2 Effective (Isotropic) Radiated Power of Transmitter Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 0.8m high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8). Calculate power in dBm by the following formula: “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 11 of 26 ERP (dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) Where: Pg is the generator output power into the substitution antenna. Above 1GHz test procedure as below: 1). Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2). Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3). Test the EUT in the lowest channel, the middle channel the Highest channel 4). The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5). Repeat above procedures until all frequencies measured was complete. Note: Reference test setup 2 5.3 Occupied Bandwidth Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The occupied bandwidth, that is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers radiated are each equal to 0.5 percent of the total mean power radiated by a given emission shall be measured. The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel, middle channel and high channel).The span of the analyzer shall be set to capture all products of the modulation process, including the emission skirts. The resolution bandwidth shall be set to as close to 1 percent of the selected span as is possible without being below 1 percent. The video bandwidth shall be set to 3 times the resolution bandwidth. Video averaging is not permitted. Where practical, a sampling detector shall be used since a peak or, peak hold, may produce a wider bandwidth than actual. The trace data points are recovered and are directly summed in linear terms. The recovered amplitude data points, beginning at the lowest frequency, are placed in a running sum until 0.5 percent of the total is reached and that frequency recorded. The process is repeated for the highest frequency data points. This frequency is recorded. The span between the two recorded frequencies is the occupied bandwidth. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 12 of 26 Note: Reference test setup 1 Band Edge at Antenna Terminals Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyser, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).in the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of 100kHz or 1% of the emission bandwidth of the fundamental emission of the transmitter may be employed. The EUT emission bandwidth is measured as the width of the signal between two points, outside of which all emission are attenuated at least 26dB below the transmitter power. The video bandwidth of the spectrum analyzer was set at thrice the resolution bandwidth. Detector Mode was set to peak or peak hold power. Note: Reference test setup 1 5.4 Spurious And Harmonic Emissions at Antenna Terminal Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 The transmitter output was connected to a calibrated coaxial cable, attenuator and Spectrum analyzer, the other end of which was connected to a Base Station Simulator. The Base Station Simulator was set to force the EUT to its maximum power setting. The tests were performed at three frequencies (low channel and high channel).The level of the carrier and the various conducted spurious and harmonic frequencies is measured by means of a calibrated spectrum analyzer. The spectrum is scanned from the lowest frequency generated in the equipment up to a frequency including its 10th harmonic. On any frequency outside a licensee’s frequency block, the power of any emission shall be attenuated below the transmitter power (P) by at least 43 + 10 log(P) dB. Compliance with these provisions is based on the use of measurement instrumentation employing a resolution bandwidth of 1 MHz or greater. However, in the 1 MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed. The emission bandwidth is defined as the width of the signal between two points, one below the carrier center frequency and one above the carrier center frequency, outside of which all emission are attenuated at least 26 dB below the transmitter power. Note: Reference test setup 1 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 13 of 26 5.5 Peak-Average Ratio Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 A peak to average ratio measurement is performed at the conducted port of the EUT. For WCDMA signals, the spectrum analyzers Complementary Cumulative Distribution Function (CCDF) measurement profile is used to determine the largest deviation between the average and the peak power of the EUT in a given bandwidth. The CCDF curve shows how much time the peak waveform spends at or above a given average power level. The percent of time the signal spends at or above the level defines the probability for that particular power level. For GSM signals, an average and a peak trace are used on a spectrum analyzer to determine the largest deviation between the average and the peak power of the EUT in a bandwidth greater than the emission bandwidth. The traces are generated with the spectrum analyzer set to zero span mode. Note: Reference test setup 1 5.6 Field Strength of Spurious Radiation Measurement Procedure: FCC KDB 971168 D01 Power Meas License Digital Systems v02r02 Below 1GHz test procedure as below: 1). The EUT was powered ON and placed on a 80cm high table in the chamber. The antenna of the transmitter was extended to its maximum length. 2). The disturbance of the transmitter was maximized on the test receiver display by raising and lowering from 1m to 4m (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) the receive antenna and by rotating through 360° the turntable. After the fundamental emission was maximized, a field strength measurement was made. 3). Steps 1) and 2) were performed with the EUT and the receive antenna in both vertical and horizontal polarization. 4). The transmitter was then removed and replaced with another antenna. The center of the antenna was approximately at the same location as the center of the transmitter. 5). A signal at the disturbance was fed to the substitution antenna by means of a non-radiating cable. With both the substitution and the receive antennas horizontally polarized, the receive antenna was raised and lowered to obtain a maximum reading at the test receiver. The level of the signal generator was adjusted until the measured field strength level in step 2) is obtained for this set of conditions. 6). The output power into the substitution antenna was then measured. 7). Steps 5) and 6) were repeated with both antennas polarized. 8) Calculate power in dBm by the following formula: ERP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBd) “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 14 of 26 Where: Pd is the dipole equivalent power, Pg is the generator output into the substitution antenna, and the antenna gain is the gain of the substitute antenna used relative to either a half-wave dipole (dBd) or an isotropic source (dBi). The substitute level is equal to Pg [dBm] – cable loss [dB]. The calculated Pd levels are then compared to the absolute spurious emission limit of -13dBm which is equivalent to the required minimum attenuation of 43 + 10log10(Power [Watts]). Above 1GHz test procedure as below: 1) Different between above is the test site, change from Semi- Anechoic Chamber to fully Anechoic Chamber 2) Calculate power in dBm by the following formula: EIRP(dBm) = Pg(dBm) – cable loss (dB) + antenna gain (dBi) EIRP=ERP+2.15dB Where: Pg is the generator output power into the substitution antenna. 3. Test the EUT in the lowest channel, the middle channel the Highest channel 4. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis positioning which it is worse case, Only the test worst case mode is recorded in the report. 5. Repeat above procedures until all frequencies measured was complete Note: Reference test setup 3 5.7 Frequency Stability / Temperature Variation Measurement Procedure: Frequency stability testing is performed in accordance with the guidelines of FCC KDB 971168 D01 Power Meas License Digital Systems v02r02. The frequency stability of the transmitter is measured by: a.) Temperature: The temperature is varied from -30°C to +50°C in 10°C increments using an environmental chamber. b.) Primary Supply Voltage: The primary supply voltage is varied from 85% to 115% of the nominal value for non hand-carried battery and AC powered equipment. For hand-carried, battery-powered equipment, primary supply voltage is reduced to the battery operating end point which shall be specified by the manufacturer. Specification – The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized frequency block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5 ppm ) of the center frequency. Time Period and Procedure: 1. The carrier frequency of the transmitter is measured at room temperature (20°C to provide a “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 15 of 26 reference). 2. The equipment is turned on in a “standby” condition for fifteen minutes before applying power to the transmitter. Measurement of the carrier frequency of the transmitter is made within one minute after applying power to the transmitter. 3. Frequency measurements are made at 10°C intervals ranging from -30°C to +50°C. A period of at least one half-hour is provided to allow stabilization of the equipment at each temperature level. Note: Reference test setup 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 16 of 26 5.8 Test Setups 5.8.1 Test Setup 1 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 17 of 26 5.8.2 Test Setup 2 Figure 1. 30MHz to 1GHz Figure 2. above 1GHz Figure 1. 30MHz to 1GHz Figure 2. above 1GHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 18 of 26 5.8.3 Test Setup 3 Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz Figure 2. 30MHz to 1GHz Figure 3. above 1GHz “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 19 of 26 5.8.4 Test Setup 4 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 20 of 26 5.9 Test Conditions Test Case Test Conditions Transmit Average Power, Test Environment Ambient Climate & Rated Voltage Output Total Test Setup Test Setup 1 Power Data RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Average Power, Test Environment Ambient Climate & Rated Voltage Spectral Density Test Setup Test Setup 1 (if required) RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Peak-to-Average Ratio Test Environment Ambient Climate & Rated Voltage (if required) Test Setup Test Setup 1 RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Modulation Characteristics Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 RF Channels (TX) M (M= middle channe ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Bandwidth Occupied Test Environment Ambient Climate & Rated Voltage Bandwidth Test Setup Test Setup 1 RF Channels (TX) M (M= middle channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Emission Test Environment Ambient Climate & Rated Voltage Bandwidth Test Setup Test Setup 1 (if required) RF Channels (TX) M (M= middle channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Band Edges Compliance Test Environment Ambient Climate & Rated Voltage Test Setup Test Setup 1 RF Channels (TX) L, H (L= low channel, H= high channel ) “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 21 of 26 Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Spurious Emission at Antenna Test Environment Ambient Climate & Rated Voltage Terminals Test Setup Test Setup 1 RF Channels (TX) L, M,H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 Field Strength of Spurious Test Environment Ambient Climate & Rated Voltage Radiation Test Setup Test Setup 2 Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 NOTE: If applicable, the EUT conf. that has maximum power density (based on the equivalent power level) is selected. RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Frequency Stability Test Env. (1) -30 °C to +50 °C with step 10 °C at Rated Voltage; (2) VL, VN and VH of Rated Voltage at Ambient Climate. Test Setup Test Setup 3 RF Channels (TX) L, M, H (L= low channel, M= middle channel, H= high channel ) Test Mode GSM/TM1;GSM/TM2;UMTS/TM1 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 22 of 26 6 Main Test Instruments Conducted Emission Cal. date Cal.Due date Inventory Item Test Equipment Manufacturer Model No. (yyyy-mm- (yyyy-mm- No. dd) dd) 1 Shielding Room ZhongYu Electron GB-88 SEL0042 2016-05-13 2017-05-13 2 LISN Rohde & Schwarz ENV216 SEL0152 2015-10-09 2016-10-09 3 LISN ETS-LINDGREN 3816/2 SEL0021 2016-05-13 2017-05-13 Fischer Custom FCC-TLISN- 4 8 Line ISN Communications EMC0120 2015-08-30 2016-08-30 T8-02 Inc. Fischer Custom FCC-TLISN- 5 4 Line ISN Communications EMC0121 2015-08-30 2016-08-30 T4-02 Inc. Fischer Custom FCC-TLISN- 6 2 Line ISN Communications EMC0122 2015-08-30 2016-08-30 T2-02 Inc. 7 EMI Test Receiver Rohde & Schwarz ESCI SEL0022 2016-05-13 2017-05-13 8 Coaxial Cable SGS N/A SEL0025 2016-05-13 2017-05-13 Universal radio 9 communication Rohde & Schwarz CMU200 SEL0091 2015-10-23 2016-10-23 tester Universal radio 10 communication Rohde & Schwarz CMU200 SEL0194 2015-10-23 2016-10-23 tester 11 DC Power Supply Zhao Xin RXN-305D SEL0117 2015-10-09 2016-10-09 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 23 of 26 RE in Chamber Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) 3m Semi-Anechoic 1 ETS-LINDGREN N/A SEL0017 2016-05-13 2017-05-13 Chamber Agilent 2 EMI Test Receiver N9038A SEL0312 2016-09-16 2017-09-16 Technologies 3 EMI Test software AUDIX E3 SEL0050 N/A N/A BiConiLog Antenna 4 ETS-LINDGREN 3142C SEL0015 2014-11-15 2017-11-15 (26-3000MHz) Double-ridged horn 5 ETS-LINDGREN 3117 SEL0006 2015-10-17 2016-10-17 (1-18GHz) Horn Antenna 6 ETS-LINDGREN 3160 SEL0076 2014-11-24 2017-11-24 (18-26GHz) Pre-amplifier Agilent 7 8447D SEL0053 2016-05-13 2017-05-13 (0.1-1300MHz) Technologies Compliance Pre-Amplifier 8 Directions PAP-0126 SEL0168 2015-10-17 2016-10-17 (0.1-26.5GHz) Systems Inc. 9 Coaxial cable SGS N/A SEL0027 2016-05-13 2017-05-13 10 Coaxial cable SGS N/A SEL0189 2016-05-13 2017-05-13 11 Coaxial cable SGS N/A SEL0121 2016-05-13 2017-05-13 12 Coaxial cable SGS N/A SEL0178 2016-05-13 2017-05-13 13 Band filter Amindeon 82346 SEL0094 2016-05-13 2017-05-13 14 Barometer Chang Chun DYM3 SEL0088 2016-05-13 2017-05-13 15 DC Power Supply Zhao Xin RXN-305D SEL0117 2015-10-09 2016-10-09 16 Humidity/ Shanhai Qixiang ZJ1-2B SEL0103 2015-10-24 2016-10-24 Temperature Indicator 17 Signal Generator Rohde & Schwarz SMR27 SEL0067 2016-05-13 2017-05-13 (10M-27GHz) 18 Loop Antenna Beijing Daze ZN30401 SEL0203 2016-05-13 2017-05-13 19 Universal radio Rohde & Schwarz CMU200 SEL0091 2016-05-13 2017-05-13 communication tester 20 Universal radio Rohde & Schwarz CMU200 SEL0194 2015-10-23 2016-10-23 communication tester “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 24 of 26 RF connected test Inventory Cal. date Cal.Due date Item Test Equipment Manufacturer Model No. No. (yyyy-mm-dd) (yyyy-mm-dd) 1 DC Power Supply Zhao Xin RXN-305D SEL0117 2015-10-09 2016-10-09 Humidity/ 2 Temperature HYGRO ZJ1-2B SEL0033 2015-10-24 2016-10-24 Indicator 3 Spectrum Analyzer Rohde & Schwarz FSP SEL0154 2015-10-17 2016-10-17 4 Coaxial cable SGS N/A SEL0178 2016-05-13 2017-05-13 5 Coaxial cable SGS N/A SEL0179 2016-05-13 2017-05-13 6 Barometer ChangChun DYM3 SEL0088 2016-05-13 2017-05-13 7 Signal Generator Rohde & Schwarz SML03 SEL0068 2016-04-25 2017-04-25 8 POWER METER R&S NRVS SEL0144 2015-10-09 2016-10-09 9 Attenuator Beijin feihang taida TST-2-6dB SEL0205 2016-04-25 2017-04-25 Universal radio 10 Rohde & Schwarz CMU200 SEL0091 2015-10-23 2016-10-23 communication tester Universal radio 11 Rohde & Schwarz CMU200 SEL0194 2015-10-23 2016-10-23 communication tester 12 Band filter amideon 82346 SEL0094 2016-05-16 2017-05-16 Agilent 13 Power Divier(splitter)) 11636B SEL0130 2015-10-24 2016-10-24 Technologies “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 25 of 26 7 Measurement Uncertainty For a 95% confidence level (k = 2), the measurement expanded uncertainties for defined systems, in accordance with the recommendations of ISO 17025 as following: Test Item Extended Uncertainty Data Transmit Output Power Data Power [dBm] U = 0.37 dB Bandwidth Magnitude [%] U = 0.2% Band Edge Compliance Disturbance Power [dBm] U = 2.0 dB Spurious Emissions, Conducted Disturbance Power [dBm] U = 2.0 dB Field Strength of Spurious ERP [dBm] For 3 m Chamber: Radiation U = 4.5 dB (30 MHz to 1GHz) U = 3.3 dB (above 1 GHz) For 10 m Chamber: U = 4.5 dB (30 MHz to 1GHz) U = 3.2 dB (above 1 GHz) Frequency Stability Frequency Accuracy [ppm] U = 0.24 ppm “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM16098050RG Page: 26 of 26 8 Photographs - EUT Test Setup Refer to Appendix A - Photographs of EUT Test Setup for SZEM1609008050RG 9 Photographs - EUT Constructional Details Refer to Appendix A - Photographs of EUT Constructional Details for SZEM1609008050RG. The End “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.”


Document Created: 2016-11-04 01:25:58
Document Modified: 2016-11-04 01:25:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC