User Manual

FCC ID: N7NBX3210

Users Manual

Download: PDF
FCCID_4229678

AirPrime BX3210 Module User Manual Applicable Model No.: AirPrime BX3210 Module

WiFi Features Description WLAN Standards IEEE 802.11 b/g/n/a/ac Antenna Port Single Antenna 2.412 GHz – 2.462 GHz Frequency Band 5.180GHz – 5.825 GHz 1 ~ 11 Channels Number of Sub Channels 36 ~ 165 Channels DSSS, CCK, OFDM, BPSK, QPSK, 16QAM, 64QAM, Modulation 256QAM Bluetooth BLE Features Description Frequency Band 2402 MHz ~ 2480 MHz Number of Sub Channels 40 channels Modulation GFSK Antenna Port Single Antenna for Wi-Fi- and BT BDR Features Description Frequency Band 2402 MHz ~ 2480 MHz Number of Sub Channels 79 channels Modulation GFSK, π/4DQPSK, 8DPSK Antenna Port Single Antenna for Wi-Fi- and BT Voltage Symbol Parameter Min. Typ. Max. Unit VBAT_RF1 3.3 V supply for RF 3.15 3.3 3.465 V 3.3V supply for 2.5V 1.71 3.3 3.46 V VBAT_BB OTP regulator VBAT_RF2 For VDD_Xtal 3.15 3.3 3.465 V

WiFi User Guide User SIDO interfacr in PC/NB control AirPrime BX3210 Module 1. power supply 3.3V 2. Linux OS (USB dongle) 3. Ctrl+Alt+T => call out terminal window 4. #sudo su 5. #cd /home 6. #Dmesg => check this device is recognized (mmc0: new high spped SDIO card at address 0001) 7. #./install_9377-3.sh => the module user mode on 8. connect to WiFi network 9. #ifconfig => check IP.

Bluetooth User Guide User UART in PC/NB control AirPrime BX3210 Module 1. power supply 3.3V 2. Linux OS (USB dongle) 3. Ctrl+Alt+T => call out terminal window 4. #sudo su 5. #cd /home 6. #Dmesg => check this device is recognized 7. # ./hciattach /dev/ttyUSB0 qca 3000000 -t120 flow 8. #hciconfig 9. #hciconfig hci0 down

10 . #bt-adapter -a hci1 -d => search BT device 11. #bt-device -a hci1 -c B8:D5:0B:2E:07 => connect BT 12. #bt-audio -a hci1 -c B8:D5:0B:2E:B3:07 13. choice sound setting 14. choice BT device and A2DP

15. open Rhythmbox Music player 16. play music

FCC ID: N7NBX3210 Federal Communication Commission Interference Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. (KDB 996369 D03 OEM Manual 2019 Feb. 01) This module is intended for OEM integrators under the following conditions: FCC: This module is certified pursuant to two Part 15 rules sections(15.407, 15.247). This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated, and must include 0.5 dB (2.4GHz) and 1.4 dB (5GHz) cable loss compensation. Technology Frequency Band Antenna Type Model Number Gain(dBi) Bluetooth 2400-2483.5MHz 2.5 Wi-Fi 2400-2483.5MHz Dipole USI05-220170 2.5 Wi-Fi 5150-5850MHz 5

The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. Information on test modes and additional testing requirements 1. This module is restricted to integration into hosts for indoor use only. 2. This module has been approved under stand-alone configuration. 3. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. 4. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. 5. The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04. Additional testing, Part 15 Subpart B disclaimer Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC authorized for the specific rule parts 15.247, 15.407 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host product as being Part 15 Subpart B compliant. Label of the end product: The host product must be labeled in a visible area with the following "Contains TX FCC ID: N7NBX3210". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user manual of the end product should include: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The antenna(s) used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is restricted to indoor use. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter.

Communication Business Group / Product Development Division Document No. Rev. 1.0 Product No. Project Code BX3210 EVB Model No. Euclid BX3210 PCB Specification for EV Board SOURCE ORGANIZATION : WP/RD/WM/HW Prepared by︰ Cren Yen Date : 2018-08-09 Checked by︰ Date : Approved by︰ Date : Concurrence︰ Date :

Doc No. Rev 1.0 Document released by WP/RD/WM/HW Date. 2018-08-09 Page 2 Description Euclid BX3210 EVB PCB Spec. Revision History Version Revised Revised by Description Notes No. Date 1.0 2018.08.09 Cren Yen Preliminary Release The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used

Doc No. Rev 1.0 Document released by WP/RD/WM/HW Date. 2018-08-09 Page 3 Description Euclid BX3210 EVB PCB Spec. 1. Scope: This PCB SPEC is for EV board of BX3210 EVB. This document define the PCB (Printed Circuit Board) manufacturing SPEC. Due to this product are applied in wireless communication field, so all the SPEC defined in this document should be followed strictly in order to control the line impedance and parasitic effects. Any changes or modification must have written agreement of USI’s engineer. 2. PCB Thickness: 1400 um +/- 100um 3. PCB size: follow gerber file 4. Four Layer PCB 5. PCB Material: FR4, , εr: 4.25 +/-0.2, Color Green, both sides. 6. Layer Stack: - Layer 1: Component Top - Layer 2: GND layer - Layer 3: POWER layer - Layer 4: Component Bottom 7. The PCB stack is as follows: (unit :um) Layer Thickness Tolerance Solder Mask 30 +/- 15 L1 30 +/- 10 P.P 250 +/- 15 L2 30 +/- 10 Core 720 +/- 50 L3 30 +/- 10 P.P 250 +/- 15 L4 30 +/- 10 Solder mask 30 +/- 15 Total Thickness: 1400 um +/- 100 um The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used

Doc No. Rev Document released by WP/RD/WM/HW Date. 2018—08—09 |Page Description Euclid BX3210 EVB PCB Spec. 8. PCB pad : 1t# 0.0762um +/— 0.0457 um, Nickel min 3um. 9. Via type : L1—L4 , PTH , minimum via : 1Omil hole / 20mil ring Impedance control is required for the following picture. RF traces @ LAYER 1 reference to Layer 2 , width: 17mil , Please adjust the trace width to fit 50 ohm. (in Red) ==RF traces @ LAYER 2 reference to Layer 1, 3, width: I9mil Please adjust the trace width to fit 50 ohm. (in Purple) 10. Panel Attached PCB area : Tolerance: +/— 0.2mm The content of this document is to be treated as strictly confidential and is not to be disclosed, reproduced or used


Document Created: 2019-04-03 17:43:03
Document Modified: 2019-04-03 17:43:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC