user manual

FCC ID: N4ZIA8X00

Users Manual

Download: PDF
FCCID_4118702

| =—&n*2 Introduction FS—(A8X Z—mERATFNARAXAEXNOIRRHEINHL , K The FS—iA8X is a single antenna bidirectional receiver using BT AFHDS 2A ( $—Niff@®ikBmDNANKHKTARK). T the AFHDS 2A (Second Generation Automatic Frequency fxfA]\TS(ET2% , SliiitHiintE PPM f&SF0 i—BUS {§&5. Hopping Digital System) protocol. It‘s compact, easy to install and can output using a standard PPM or i—BUS signal. | Ets Receiver overview MFERERMUSREAESEM+. PPM {2SBA : #i4Htrff} PPM E5. Antenna PPM i—BUS 1E8S$##0 : MBFtiH i—BUS {35., a) VCC : MBiREBEEFy 4.0~8.4V. GCIOh _ i—BUS GND : jiE}#Xb#, Kn EKn VCC C» These ports connect the receiver to various models, =| component‘s and flight controllers. n GND PPM signal port: Outputs standard PPM signal. i—BUS signal port: Outputs i—BUS signal. VCC: Power supply voltage from 4.0 — 84V. GND: Connect to ground wire. > taSsif : {ERHpipiflrAtr‘mSsBR*LEA , allofESHERtSRA XAR , HSELAXAIREINNMEE , REXMEARRNVL MEXMARAHNNRIRNIEINTIARTELITE , ReabcSHEiSREe KHiat=5| 44T(Em5s |ARSA. IHinElkh<ixfrs—RANL , bAAigERatGfRAEASAEAEE. EIkNAKkSCSSREHH , Plin€lstetiimials. JA rRtesint#_/if , fiRsktfertir2z>l0=.>6 1e LA—AYREE. ied , s#itEREAVIGIE , MtuEenrt~cEAYmX. > Attention: Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury. Make sure the receiver‘s battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation or loss of control. Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise. Keep the receiver‘s antenna at least 1cm away from conductive materials such as carbon or metal. Do not power on the receiver during the setup process to prevent loss of control. [ pmame 1. First put the transmitter into bind mode (see the 1. SEKNNRAAXNHMIAEG ; ( LAHNVRARAXHYIANEAITIG—S dETA , HtRie®A2t HLAYIEEMHIRANRIRTTIERATE ) transmitter‘s user manual for instructions on how to 2. RANREEERMNRAXNIIAG ; activate bind mode.) EseE , $# 1s aitNRBIXRC ; 2. Connect the receiver to power, after 1 second the ENUier]kRAZETRAXNSIAR ; receiver‘s LED will start to flash indicating that it has 3. RNNIENIEARESNT , ZmrfGRtT) , oSHiK entered bind mode. HUETIE(GE. 3. When the receiver‘s LED stops flashing the transmitter 4. KERSNL EKXH REREAERE. IFSXDXTNY , and receiver have successfully bound. HeSell—PRERIXING. 4. Check to make sure that the transmitter and receiver are working as expected, if there are any issues or unexpected operation follow the steps above to bind again. http://www.flysky—cn.com Copyright ©2018 Flysky Technology co., Itd

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: N4ZIA8X00 or Contains FCC ID: N4ZIA8X00” When the module is installed inside another device, the user manual of the host must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement,Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirement，then the host can be sold legally.


Document Created: 2018-12-27 14:55:49
Document Modified: 2018-12-27 14:55:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC