Manual

FCC ID: M5V19087Y

Users Manual

Download: PDF
FCCID_272230

Installation Note Cardax Prox Plus 125 Reader CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. Before you Begin Unpack the Cardax Prox Plus 125 reader and check the shipment contains the following items: • 1 x Cardax Prox Plus 125 base with cable and Processor Box attached • 1 x Cardax Prox Plus 125 facia • 1 x printed circuit board (PCB) assembly • 1 x dispatch kit containing the following; 1 x 4-way IDC connector 1 x grommet plug 4 x self tapper pan head screws 4 x plastic caps Part Number 3E1086 R2 1 September 2002

Power Supply Requirements The Prox Plus 125 reader requires a supply of 13.6 V DC +/- 15% at 200 mA. Prox Plus 125 readers require a good quality linear power source. Note: Switch mode power supplies are not recommended as they may reduce the read range of the Prox Plus 125 reader. Cabling Use 4 core, 0.2 mm2 (AWG 24) cabling with a maximum, nominal capacitance of 120 pf/m. The maximum external diameter of the cable must not exceed 5mm (1/5 inch). The maximum distance between the URI and the Prox Plus 125 reader with this cable is 200m (650ft). Note: You need a special cable terminating tool to connect the building cabling to the Prox Plus 125. The tool has a head (Part No. C861145) and handle (Part No. C861115). 2 Part Number 3E1086 R2 September 2002

Mounting Distance Between Proximity Readers The distance between any 2 proximity readers must be greater than 200mm in all directions. Please note that 200mm in all directions includes the distance through walls. m 200m Proximity Proximity Reader Reader Wall Less than 200mm thick Part Number 3E1086 R2 3 September 2002

Mounting Note: The Prox Plus 125 reader has been designed to metric specifications therefore any imperial measurements provided are approximate only. The Prox Plus 125 reader is designed to be mounted on any solid flat surface including metal surfaces. The recommended mounting height for the Prox Plus 125 reader is 1100mm from floor level to the centre of the reader unit. However this may vary in some countries and you should check local regulations for variations to this height. Note: The grommet through which the cables feed into the base of the Prox Plus 125 reader helps to keep the unit waterproof. Drill a 20mm (3/4 inch) diameter hole for the base extrusion through or into the mounting surface to a minimum depth of 40mm (11/2 inch). Run the building cabling through the base and grommet. Fit the base to the 20mm (3/4 inch) hole and secure it to the mounting surface using the four fixing screws. Fit the screw caps over each fixing screw. The screw caps prevent water from entering the reader via the fixing holes. The caps must be installed for the Prox Plus 125 reader to comply with the environmental specification. Note: It is very important that the base of the reader is flush with and tight against the mounting surface. If you are mounting the Prox Plus 125 reader on a rough surface you should make the surface as smooth as possible under the reader and up to 25mm (1 inch) around the reader. 4 Part Number 3E1086 R2 September 2002

Removing the Facia To remove the facia from the Prox Plus 125 base you need the plastic de-latching tool (Part No. C41612) shown below. Slide the de-latching tool firmly under the bottom of the Prox Plus 125 reader. Hold the top of the reader with your fingers and squeeze the de-latching tool up, towards the top of the reader with your thumb. Lift the facia away from the base. If the base is not flush to the wall, or the screws have become loose you may need to pack the space between the de-latching tool and the wall. A thin piece of cardboard is usually all that is necessary, i.e. a business card folded in two. Cut a notch in the folded edge of the card similar in shape to the notch in the de-latching tool as shown below. Slide the card under the bottom of the facia and then use the de-latching tool with the card as packing. Part Number 3E1086 R2 5 September 2002

Connecting to the URI The Prox Plus 125 reader can connect to either a Cardax IV or CardaxFT URI. Use the cable terminating tool to connect the cables to the socket as described in the following sections. Pin number 4 of the Prox Plus 125 connector feeds into the cable terminating tool first. The pin numbers are marked on the connector. Connecting to the CardaxFT URI Connect the cables to the socket as shown. CardaxFT Universal Reader Interface Prox Plus 125 Connector Plug P1 or P2 Black GND 4 Blue 3 OUTPUTS White OUTPUTS 2 Red DET 1 COMMS COMMS 5/12V Connect the Prox Plus 125 connector to either the P1 or P2 plug on the CardaxFT URI. Refer to the CardaxFT URI component layout diagram, below, for the location of the plugs. F1 P3 13.6 V Input Fuse D10 P5 Keypad Rating = 500mA Comms LED Power & Comms pin 1 = Row1 flashing = communicating with pins 1 & 2 = RS485 pin 2 = Row 2 FT Controller pin 3 = 13.6 V ± 15% P2 pin 3 = Row 3 pin 4 = 0V Non-CardaxFT pin 4 = Row 4 P6 pin 5 = Column1 Reader 2 pin 6 = Column2 13.6 V ± 15%out pin 1 = 5/12 V power pin 7 = Column3 pin 1 = 13.6 V ± 15% 1 E D10 GND pin 2 = DataA pin 8 = Ground pin 2 = Ground 3A fused P6 COMMS U19 pin 3 = DataB T1 + pin 4 = Card detect JP1 1 P5 D22 pin 5 = LED output F2 Reader Voltage select + pin 6 = Beeper output C30 pin 7 = Ground 13.6 V Output Fuse D13 = 5V (200mA total) GND D12 Rating = 3A = 12V (1A total) D11 1 P2 NC GND 5V 12V JP1 D16 D17 and D21 COM NO D17 NC NO OUTPUTS P3 D19 COIL Relay state indicators Q7 LED on = Energised RLY1 JP2 P7 D20 D15 LED off = De-energised NC DET D6 COMM NO COMMS D5 D14 P7 COM R7 Q41 D21 NC NO COIL Relay Outputs GND D4 5/12V GND RLY2 pin 1 = R1 Normally closed 1 pin 2 = R1 Normally open 1 IN1 Q2 COMM Q26 pin 3 = R1 Common D18 R53 pin 4 = R2 Normally closed OUTPUTS D23 IN2 R50 D24 R54 Q27 pin 5 = R2 Normally open R51 pin 6 = R2 Common IN3 R55 Q28 D3 D25 R52 pin 7 = Ground DET Q29 P4 R79 IN5 IN4 D26 R94 R80 Q30 D27 COMMS D18 D2 R95 P8 D28 R81 R96 Q31 Run LED GND IN6 D1 2 10 5/12V 0 SW1 1 9 1 P1 (c)1999 PEC(New Zealand) Ltd 22825V2 Assy 22826 REV[A][B][C] P1 P8 SW1 P4 Non-CardaxFT Diagnostic port Unit address Balanced Inputs Reader 1 Set unit number pin 1 = Input1 pin 1 = 5/12 V power pin 2 = Input 2 pin 2 = DataA pin 3 = Input 3 pin 3 = DataB pin 4 = Input 4 pin 4 = Card detect pin 5 = Input 5 pin 5 = LED output pin 6 = Input 6 pin 6 = Beeper output pin 7 = Ground pin 7 = Ground 6 Part Number 3E1086 R2 September 2002

Connecting to the Cardax IV URI Connect the cables to the socket as shown. Note: The colours shown in the diagram below are those used in the cable assembly (Part No. 190810) which may be ordered already assembled. Universal Reader Interface Prox Plus 125 Connector Plug P4 (Exit) or P5 (Entry) Black GND 4 1 Blue 3 2 BPR White 2 3 LED Red DET 1 4 5 1-CK 6 0-DT 7 5/12V Note: Refer to the Cardax IV URI Settings section, later in this Installation Note, for the location of the Cardax IV URI components. Replacing the Facia Push the socket back into the grommet. Push the connector into the socket and grommet combination. Push the connector, socket and grommet back into the Prox Plus 125 base. Firmly clip the interconnect PCB under the retaining clips in the base. Fit the facia assembly onto the base by clipping the front over the top edge of the base and pressing the bottom of the facia down un til it clicks into place. Note: The pins on the interconnect PCB in the base of the Prox Plus 125 reader, fit into the slots on the main PCB. The connector should be fitted to the base, not the facia. Part Number 3E1086 R2 7 September 2002

Initialisation Initialising with the CardaxFT URI The CardaxFT URI must be allocated a unique unit address which is set up at the CardaxFT URI and at the Command Centre FT Server. Refer to the CardaxFT Universal Reader Interface Installation Note and the Command Centre FT documentation. Note: When configuring Command Centre FT you will need to know the plug (P1 or P2) to which the Prox Plus 125 reader is connected. Initialising with the Cardax IV URI Type of Door Lock Depending on the type of lock fitted to the door that the reader is controlling, you will need to initialise the URI with the door either closed or open. If you initialise the URI with the door held open, it sets the door to unlock and remains unlocked until the door is fully closed again. If you initialise the URI with the door closed it sets the door to unlock and resets to lock as soon as the door is opened. Push-Button Exit If the door has a push button exit, ensure the URI Exit terminal has the push-button fitted and correctly terminated with a 10 kW resistor before you power on. Check Software Version You should check the URI software version to ensure it is correct for your installation. The software version number is written on the label of the EPROM mounted at the bottom right of the URI processor board. URI software versions that are compatible with the Prox Plus 125 reader are shown below: URI Software Reader Type vW6.10 or later version One door Cardax Prox or Swipe Readers vW7.10 TC or later version URI Special Options : Cardax Turnstile format vW9.10 or later version Two door Cardax Prox or Swipe Readers Note : The vW6.xx and vW9.xx versions will have one of the following suffixes: GT = 2 wire modem connection G = 4 wire modem connection // = direct connection via comms lines ie. no modem 8 Part Number 3E1086 R2 September 2002

Cardax IV URI Settings Please refer to the diagram below for the location of the URI components. Fuse Fuses (Reader Power (Relay Supply) Contacts) Lithium Battery Lithium Battery Jumper 1 Top Row Comms J1 2 Row 2 & Power P7 3 Row 3 Door 1 4 Bottom Row Ground COM B D8 Keypad 5 Left Column COM A P1 Comms In D45 6 Middle Column Power F1 F2 5 V DC 7 Right Column 8 Not Used D10 1 Normally Open Comms Out P8 2 Relay Common 3 Normally Closed Ground GND Normally Open N.O. F3 Aux. Relay Door 1 Inputs or Door 2 Relay Common COM & Normally Closed N.C. P2 Output Relay Relay J2 OFF Confirmed Entry ON No Confirmed Entry Door Unlock UNLK Door Open OPEN Tamper Push-Button Exit EXIT Cardax III Earth Wire 5V Ground GND Auxiliary and/or Input 1 AUX1 Input 2 AUX2 Door 2 Inputs D44 Input 3/*Unlock AUX3 P3 Diagnostics/ Processing Input 4/*Open AUX4 Cardax Prox (125, Input 5/*Exit AUX5 Mifare or * Applies to 2-Door TIRIS)/ URI only Cardax Ground GND Door 1 Exit Swipe Reader OR 12 V Beeper BPR LED LED Door 2 Entry Reader PLD Wiegand Card Detect DET P4 5V Clock/Data 1 1-CK Data/Data 0 0-DT 5 or 12 V Out 5/12V Ground GND Wiegand Beeper BPR EPROM 12 V LED LED Jumpers Card Detect DET P5 Clock/Data 1 1-CK Data/Data 0 0-DT Door 1 Entry Reader ON DSW1DSW2ON 5 or 12 V Out 5/12V OFF OFF Jumper Connected No Jumper Switch On Off Switch On Off 1 1 1 2 2 2 Card Format 3 4 Unit 3 4 8 Address 4 5 16 5 6 32 6* Validated Exit* Normal* 7 Initialise Normal 7* *see note below 8* *see note below 8 Keypad No Keypad * Depends on Software Version. Part Number 3E1086 R2 9 September 2002

Tamper the URI by opening the door of the cabinet. This releases the tamper switch. The URI has a set of six jumpers grouped into two sets of three. One group is labelled ENTRY and the other is labelled EXIT. ENTRY jumpers set the voltage and card type of the reader connected to plug P5. EXIT jumpers set the voltage and card type of the reader connected to plug P4. Set the Entry and Exit jumpers for the Prox Plus 125 reader as shown below: Entry and Exit Jumper Settings Cardax 12 V 1 Exit 2 3 4 Entry 5 6 = jumper in place Pins 3 and 6 = voltage supplied to reader Pins 1,2 4 and 5 = reader type Connector J2 controls the Confirmed Entry function. If you initialise the URI with no jumper fitted on J2 the Confirmed Entry function will be ON. To switch the Confirmed Entry function OFF, you must initialise the URI with one a mini jumper fitted across both pins of connector J2. Connect the Prox Plus 125 reader to the URI Entry plug (P5). Note: If you are installing two entry readers (2 door URI software) you must connect the second entry reader to Plug P4 to initialise the URI. If you are installing only an Exit reader you must connect the reader to the Entry Plug P5 to initialise the URI. Ensure Entry and Exit jumpers are set to the same configuration. After you have initialised the URI you should connect the Exit reader to Exit Plug P4. 10 Part Number 3E1086 R2 September 2002

Set DIPSW1 as follows: Switches On Off 1 1 2 2 3 4 Unit Addresses 4 8 5 16 6 32 7 Initialise Normal 1 door software 1 door software 8 = liftcar reader = door reader 2 door software 2 door software = keypad on door 2 = no keypad on door 2 Set DIPSW2 as follows, where 0 = OFF and 1 = ON: vW6.10, vW7.10, URI Software vW9.10 or later versions. DIPSW2 Reader 12345678 Prox Plus 125, no authorised exit 00000001 Prox Plus 125, with authorised exit 00000101 For further details on software versions refer to Check Software Version in the Initialisation section earlier in this Installation Note. CAUTION ! Do not fit the lithium battery jumper (J1) before powering up the URI. If the jumper is fitted you must remove it and wait 10 seconds. Power up the URI. The yellow LED (D45) should be permanently ON. This indicates that 5 V is present on the board. The green LED (D44) should flash twice, pause, then flash twice again. This is a continuous sequence while the URI is unitialised and indicates it is processing. The red LED (D8) should flash if polls are received from the Commander. Note: A URI can be initialised without being connected to a Commander Part Number 3E1086 R2 11 September 2002

Set DIPSW1:7 to ON. Present a Prox 125 card to the Prox Plus 125 reader. Note:You must present the card within 30 seconds of setting DIPSW1:7 to ON. If you are initialising with two readers connected to the URI, you should present the card to the reader on URI plug P5. Set DIPSW1:7 to OFF The green LED (D44) will begin flashing continuously. The other red LED (D10) will flash each time the URI replies to a poll from the Commander. Replace the lithium battery jumper (J1). Restore the tamper by closing the door of the cabinet. Approvals and Standards This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Note: Changes or modifications not expressly approved by Cardax (International) Ltd could void the user's authority to operate the equipment. 12 Part Number 3E1086 R2 September 2002

125 reader displays the following icons on the liquid erystal display (LCD) e access status of the zone controlled by the reader. Condition Steady Flashing Secure ’_fl V PIN Only sees @ Free Access Access Granted Access Denied Card Plus PIN Wrong PIN Dual Auth or Escort Set Allowed Set Unset Set Unset plus PIN n oug Set Failed Waiting for Commander Un—initialised 13 ...............


Document Created: 2002-09-17 08:24:20
Document Modified: 2002-09-17 08:24:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC