Test Report 15B

FCC ID: LYHSIDTAB01

Test Report

Download: PDF
FCCID_894140

FCC Measurement/Technical Report on Bluetooth Transceiver ISID Report Reference: MDE_Siem_0617_FCCc Test Laboratory: 7 layers AG DAT-P-192/99-01 Borsigstrasse 11 40880 Ratingen Germany email: info@7Layers.de Note: The following test results relate only to the devices specified in this document. This report shall not be reproduced in parts without the written approval of the testing laboratory. 7 layers AG Aufsichtsratsvorsitzenderh Registergerichth registered in: Borsigstrasse 11 Chairman of the Supervisory Board: Düsseldorf, HRB 44096 40880 Ratingen, Germany Markus Becker USt-IdNr h VAT Nr: Phone: +49 (0) 2102 749 0 Vorstandh Board: DE 203159652 Fax: +49 (0) 2102 749 350 Dr. Hans-Jürgen Meckelburg www.7Layers.com René Schildknecht InterLab® is a registered trademark of 7 layers AG

Table of Contents 0 Summary 3 0.1 Technical Report Summary 3 0.2 Measurement Summary 4 1 Administrative Data 5 1.1 Testing Laboratory 5 1.2 Project Data 5 1.3 Applicant Data 5 1.4 Manufacturer Data 5 2 Product labeling 6 2.1 FCC ID label 6 2.2 Location of the label on the EUT 6 3 Test object Data 7 3.1 General EUT Description 7 3.2 EUT Main components 8 3.3 Ancillary Equipment 8 3.4 EUT Setups 8 3.5 Operating Modes 8 4 Test Results 9 4.1 Conducted emissions (AC power line) 9 4.2 Spurious radiated emissions 11 5 Test Equipment 14 6 Photo Report 17 7 Setup Drawings 18 8 Annex measurement plots 19 8.1 AC Mains conducted 19 8.2 Spurious radiated emissions 20 Test report Reference: MDE_Siem_0617_FCCc Page 2 of 20

0 Summary 0.1 Technical Report Summary Type of Authorization Certification for an Intentional Radiator (Periodic operation in the band above 70 MHz) Applicable FCC Rules Prepared in accordance with the requirements of FCC Rules and Regulations as listed in 47 CFR Ch.1 Parts 2 (10-1-06 Edition) and 15 (10-1-06 Edition). The following subparts are applicable to the results in this test report. Part 2, Subpart J - Equipment Authorization Procedures, Certification Part 15, Subpart A – General § 15.33 Frequency range of radiated measurements Part 15, Subpart B – Unintentional Radiators § 15.101 Equipment authorization of unintentional radiators § 15.107 Conducted limits § 15.109 Radiated emission limits Note: none Summary Test Results: The EUT complied with all performed tests as listed in chapter 0.2 Measurement Summary. Test report Reference: MDE_Siem_0617_FCCc Page 3 of 20

0.2 Measurement Summary FCC Part 15, Subpart B § 15.107 Conducted emissions (AC power line) The measurement was performed according to ANSI C63.4 2003 OP-Mode Setup Port Final Result op-mode 1 Setup_a01 AC Port (power line) passed FCC Part 15, Subpart B § 15.109 Spurious Radiated Emissions The measurement was performed according to ANSI C63.4 2003 OP-Mode Setup Port Final Result op-mode 1 Setup_a01 enclosure passed Responsible for Responsible Accreditation Scope: for Test Report: Test report Reference: MDE_Siem_0617_FCCc Page 4 of 20

1 Administrative Data 1.1 Testing Laboratory Company Name: 7 Layers AG Address Borsigstr. 11 40880 Ratingen Germany This facility has been fully described in a report submitted to the FCC and accepted under the registration number 96716. The test facility is also accredited by the following accreditation organisation: - Deutscher Akkreditierungs Rat DAR-Registration no. DAT-P-192/99-01 Responsible for Accreditation Scope: Dipl.-Ing. Bernhard Retka Dipl.-Ing. Robert Machulec Dipl.-Ing. Thomas Hoell Report Template Version: 2006-12-18 1.2 Project Data Responsible for testing and report: Dipl.-Ing. Robert Machulec Date of Test(s): 2007-06-01 Date of Report: 2007-07-06 1.3 Applicant Data Company Name: Siemens AG Address: Siemensallee 84 76187 Karlsruhe Germany Contact Person: Markus Rödle 1.4 Manufacturer Data Company Name: please see applicant data Address: Contact Person: Test report Reference: MDE_Siem_0617_FCCc Page 5 of 20

2 Product labeling 2.1 FCC ID label At the time of the report there was no FCC label available. 2.2 Location of the label on the EUT see above Test report Reference: MDE_Siem_0617_FCCc Page 6 of 20

3 Test object Data 3.1 General EUT Description Equipment under Test Bluetooth Transceiver Type Designation: ISID Kind of Device: Integrated Service Integration Display, (optional) WLAN/Bluetooth handheld device Voltage Type: AC Voltage level: 115 V General product description: Bluetooth is a short-range radio link intended to be a cable replacement between portable and/or fixed electronic devices. Bluetooth operates in the unlicensed ISM Band at 2.4 GHz. In the US a band of 83.5 MHz width is available. In this band, the Bluetooth technology defines 79 RF channels spaced 1 MHz (2402 - 2480 MHz). The actual RF channel is chosen from a pseudo-random hopping sequence through the 79 channels. The EUT provides the following ports: Ports AC Port (power line) enclosure The main components of the EUT are listed and described in Chapter 3.2 Test report Reference: MDE_Siem_0617_FCCc Page 7 of 20

3.2 EUT Main components Type, S/N, Short Descriptions etc. used in this Test Report Short Equipment Type Serial No. HW SW Date of Description under Test Designation Status Status Receipt EUT A Bluetooth ISID - 1.0 1.0 2007-04-16 (Code: Transceiver 01120d01) Remark: none NOTE: The short description is used to simplify the identification of the EUT in this test report. 3.3 Ancillary Equipment For the purposes of this test report, ancillary equipment is defined as equipment which is used in conjunction with the EUT to provide operational and control features to the EUT. It is necessary to configure the system in a typical fashion, as a customer would normally use it. But nevertheless Ancillary Equipment can influence the test results. Short Equipment Type HW Status SW Status Serial no. FCC ID Description under Test Designation AE1 Keyboard Logitech – – 867618- – UltraX Media 0102 Y-BL49A AE2 Mouse Logitech M- – – LZC9050547 – BB48 8 AE3 AC Adapter VAN90A-195A – – 1006360000 – 9-00 3.4 EUT Setups This chapter describes the combination of EUTs and ancillary equipment used for testing. Setup No. Combination of EUT’s Description Setup_a01 EUT A+AE1+AE2+AE3 - 3.5 Operating Modes This chapter describes the operating modes of the EUT's used for testing. Op. Mode Description of Operating Modes Remarks op-mode 1 TX on Bluetooth (2402MHz) and WLAN (2412MHz, n-mode) Test report Reference: MDE_Siem_0617_FCCc Page 8 of 20

4 Test Results 4.1 Conducted emissions (AC power line) Standard FCC Part 15, 10-1-06 Subpart B The test was performed according to: ANSI C 63.4, 2003 4.1.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C 63.4-2003. The Equipment Under Test (EUT) was setup in a shielded room to perform the conducted emissions measurements in a typical installation configuration. The EUT was powered from 50µH || 50 Ohm Line Impedance Stabilization Network (LISN). The LISN’s unused connections were terminated with 50 Ohm loads. The measurement procedure consists of two steps. It is implemented into the EMI test software ES-K1 from R&S. Step 1: Preliminary scan Preliminary test to identify the highest amplitudes relative to the limit. EMI receiver settings: - Detector: Peak - Maxhold - Frequency range: 150 kHz – 30 MHz - Frequency steps: 5 kHz - IF–Bandwidth: 10 kHz - Measuring time / Frequency step: 1 ms - Measurement on phase + neutral lines of the power cords Intention of this step is, to determine the conducted EMI-profile of the EUT. With this data, the test system performs (to reduce the number of final measurements) a data reduction with the following parameters: - Offset for acceptance analysis: Limit line – 6 dB - Maximum number of final measurements: 6 Step 2: Final measurement With the frequencies determined in step 1, the final measurement will be performed. EMI receiver settings: - Detector: Quasi-Peak - IF - Bandwidth: 9 kHz - Measuring time: 1s / frequency 4.1.2 Test Requirements / Limits FCC Part 15, Subpart B, §15.107 Frequency Range (MHz) QP Limit (dBµV) AV Limit (dBµV) 0.15 – 0.5 66 to 56 56 to 46 0.5 – 5 56 46 5 – 30 60 50 Used conversion factor: Limit (dBµV) = 20 log (Limit (µV)/1µV). Test report Reference: MDE_Siem_0617_FCCc Page 9 of 20

4.1.3 Test Protocol Temperature: 25 °C Air Pressure: 1024 hPa Humidity: 45 % Op. Mode Setup Port op-mode 1 Setup_a01 AC Port (power line) Power Frequency Measured value Delta to limit Remarks line MHz dBµV dBµV L1 345 51.50 7.6 QP L1 480 48.10 8.2 QP L1 1040 47.90 8.1 QP L1 1135 46.60 9.4 QP L1 1520 43.30 12.7 QP L1 1680 43.30 12.7 QP L1 2265 46.10 9.9 QP L1 2395 41.50 13.5 QP N 2910 44.10 11.9 QP L1 3590 40.10 15.9 QP L1 325 45.40 4.1 AV L1 480 40.60 5.7 AV L1 885 38.40 7.6 AV N 975 42.00 4.0 AV L1 1055 45.50 0.5 AV N 1130 44.20 1.8 AV N 1535 42.60 3.4 AV N 1700 34.40 11.6 AV L1 1785 42.50 3.5 AV L1 2265 38.70 7.3 AV Remark: Please see annex for the measurement plot. 4.1.4 Test result: Conducted emissions (AC power line) FCC Part 15, Subpart B Op. Mode Result op-mode 1 passed Test report Reference: MDE_Siem_0617_FCCc Page 10 of 20

4.2 Spurious radiated emissions Standard FCC Part 15, 10-1-06 Subpart B The test was performed according to: ANSI C 63.4, 2003 4.2.1 Test Description The test set-up was made in accordance to the general provisions of ANSI C 63.4-2003. The Equipment Under Test (EUT) was set up on a non-conductive table 1.0 x 2.0 m in the semi-anechoic chamber. The test was performed at the distance of 3 m between the EUT and the receiving antenna. The radiated emissions measurements were made in a typical installation configuration. The measurement procedure is implemented into the EMI test software ES-K1 from R&S. Measurement between 30 MHz and 1 GHz Step 1: Preliminary scan Preliminary test to identify the highest amplitudes relative to the limit. Settings for step 1: - Detector: Peak-Maxhold - Frequency range: 30 – 1000 MHz - Frequency steps: 60 kHz - IF–Bandwidth: 120 kHz - Measuring time / Frequency step: 100 µs - Turntable angle range: –180 to 180 ° - Turntable step size: 90° - Height variation range: 1 – 3m - Height variation step size: 2m - Polarisation: Horizontal + Vertical Intention of this step is, to determine the radiated EMI-profile of the EUT. Afterwards the relevant emissions for the final measurement are identified. Step 2: second measurement For the relevant emissions determined in step 1, an additional measurement with the following settings will be performed. Intention of this step is, to find out the approximate turntable angle and antenna height for each frequency. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100ms - Turntable angle range: –180 to 180 ° - Turntable step size: 45° - Height variation range: 1 – 4m - Height variation step size: 0.5m - Polarisation: horizontal + vertical After this step the EMI test system has determined the following values for each frequency (of step 1): - Frequency - Azimuth value (of turntable) - Antenna height The last two values have now the following accuracy: - Azimuth value (of turntable): 45° - Antenna height: 0.5m Step 3: final measurement Test report Reference: MDE_Siem_0617_FCCc Page 11 of 20

In this step the accuracy of the turntable azimuth and antenna height will be improved. This is necessary to find out the maximum value of every frequency. For each frequency the turntable azimuth and antenna height, which was determined in step 3, will be adjusted. The turntable azimuth will be slowly varied by +/- 22.5° around this value. During this action the value of emission is continuously measured. The turntable azimuth at the highest emission will be recorded and adjusted. In this position the antenna height is also slowly varied by +/- 25 cm around the antenna height determined in step 3. During this action the value of emission is also continuously measured. The antenna height of the highest emission will also be recorded and adjusted. - Detector: Peak – Maxhold - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 100ms - Turntable angle range: –22.5° to + 22.5 ° around the value determined in step 2 - Height variation range: -0.25m to + 0.25m around the value determined in step 2 Step 4: final measurement with QP detector With the settings determined in step 3, the final measurement will be performed: EMI receiver settings for step 4: - Detector: Quasi-Peak(< 1GHz) - Measured frequencies: in step 1 determined frequencies - IF – Bandwidth: 120 kHz - Measuring time: 1s 4.2.2 Test Requirements / Limits FCC Part 15, Subpart B, §15.109, Radiated Emission Limits Frequency Range (MHz) Class B Limit (dBµV/m) 30 – 88 40.0 88 – 216 43.5 216 – 960 46.0 above 960 54.0 Test report Reference: MDE_Siem_0617_FCCc Page 12 of 20

4.2.3 Test Protocol Temperature: 25 °C Air Pressure: 1024 hPa Humidity: 45 % Op. Mode Setup Port op-mode 1 Setup_a01 Enclosure Polari- Frequency Corrected value Limit Limit Limit Delta to Delta to sation MHz dBµV/m dBµV/ dBµV/ dBµV/ limit limit m m m dB dB QP Peak AV QP Peak AV QP/Peak AV Horizontal 30.18 15.50 40.0 24.5 Vertical 30.54 15.70 40.0 24.3 Horizontal 31.02 15.00 40.0 25.0 Horizontal 83.22 30.10 40.0 9.9 Horizontal 85.98 33.00 40.0 7.0 Horizontal 116.22 34.50 43.5 9.0 Horizontal 117.36 30.00 43.5 13.5 Horizontal 117.72 33.00 43.5 10.5 Horizontal 119.22 32.60 43.5 10.9 Horizontal 120.60 32.80 43.5 10.7 Remark: No further spurious emissions in the range 20 dB below the limit found. 4.2.4 Test result: Spurious radiated emissions FCC Part 15, Subpart B Op. Mode Result op-mode 1 passed Test report Reference: MDE_Siem_0617_FCCc Page 13 of 20

5 Test Equipment EUT Digital Signalling System Equipment Type Serial No. Manufacturer Digital Radio CMD 55 831050/020 Rohde & Schwarz Communication Tester Signalling Unit for PTW60 100004 Rohde & Schwarz Bluetooth Spurious Emissions Universal Radio CMU 200 102366 Rohde & Schwarz Communication Tester EMI Test System Equipment Type Serial No. Manufacturer Comparison Noise CNE III 99/016 York Emitter EMI Analyzer ESI 26 830482/004 Rohde & Schwarz Signal Generator SMR 20 846834/008 Rohde & Schwarz EMI Radiated Auxiliary Equipment Equipment Type Serial No. Manufacturer Antenna mast 4m MA 240 240/492 HD GmbH H. Deisel Biconical dipole VUBA 9117 9117108 Schwarzbeck Broadband Amplifier JS4-18002600-32 849785 Miteq 18MHz-26GHz Broadband Amplifier JS4-00101800-35 896037 Miteq 30MHz-18GHz Broadband Amplifier JS4-00102600-42 619368 Miteq 45MHz-27GHz Cable "ESI to EMI EcoFlex10 W18.01-2 + W38.01-2 Kabel Kusch Antenna" Cable "ESI to Horn UFB311A + UFB293C W18.02-2 + W38.02-2 Rosenberger-Microcoax Antenna" Double-ridged horn HF 906 357357/002 Rohde & Schwarz Double-ridged horn HF 906 357357/001 Rohde & Schwarz High Pass Filter 5HC3500/12750-1.2-KK 200035008 Trilithic High Pass Filter 5HC2700/12750-1.5-KK 9942012 Trilithic High Pass Filter 4HC1600/12750-1.5-KK 9942011 Trilithic KUEP pre amplifier Kuep 00304000 001 7layers Log.-per. Antenna HL 562 Ultralog 830547/003 Rohde & Schwarz Loop Antenna HFH2-Z2 829324/006 Rohde & Schwarz Pyramidal Horn Antenna Model 3160-09 9910-1184 EMCO 26.5 GHz Test report Reference: MDE_Siem_0617_FCCc Page 14 of 20

EMI Conducted Auxiliary Equipment Equipment Type Serial No. Manufacturer Cable "LISN to ESI" RG214 W18.03+W48.03 Huber+Suhner Two-Line V-Network ESH 3-Z5 828304/029 Rohde & Schwarz Two-Line V-Network ESH 3-Z5 829996/002 Rohde & Schwarz Auxiliary Test Equipment Equipment Type Serial No. Manufacturer Broadband Resist. 1506A / 93459 LM390 Weinschel Power Divider N Broadband Resist. 1515 / 93459 LN673 Weinschel Power Divider SMA Digital Multimeter 01 Voltcraft M-3860M IJ096055 Conrad Digital Multimeter 02 Voltcraft M-3860M IJ095955 Conrad Digital Oscilloscope TDS 784C B021311 Tektronix Fibre optic link Satellite FO RS232 Link 181-018 Pontis Fibre optic link FO RS232 Link 182-018 Pontis Transceiver I/Q Modulation AMIQ-B1 832085/018 Rohde & Schwarz Generator Notch Filter ultra stable WRCA800/960-6E 24 Wainwright Spectrum Analyzer 9 FSP3 838164/004 Rohde & Schwarz kHz to 3 GHz Temperature Chamber VT 4002 58566002150010 Vötsch Temperature Chamber KWP 120/70 59226012190010 Weiss ThermoHygro Opus10 THI (8152.00) 7482 Lufft Mess- und Datalogger 03 Regeltechnik GmbH Anechoic Chamber Equipment Type Serial No. Manufacturer Air Compressor Atlas Copco (pneumatic) Controller CO 2000 CO2000/328/12470406 Innco innovative /L constructions GmbH EMC Camera CE-CAM/1 CE-SYS EMC Camera for CCD-400E 0005033 Mitsubishi observation of EUT Filter ISDN B84312-C110-E1 Siemens&Matsushita Filter telephone systems B84312-C40-B1 Siemens&Matsushita / modem Filter Universal 1A B84312-C30-H3 Siemens&Matsushita Fully/Semi AE Chamber 10.58x6.38x6 Frankonia Turntable DS 420S 420/573/99 HD GmbH, H. Deisel Valve Control Unit VE 615P 615/348/99 HD GmbH, H. Deisel (pneum.) Test report Reference: MDE_Siem_0617_FCCc Page 15 of 20

7 layers Bluetooth Full RF Test Bluetooth RF Conformance Solution Test System TS8960 Equipment Type Serial No. Manufacturer 10 MHz Reference MFS 5489/001 Efratom Power Meter NRVD 832025/059 Rohde & Schwarz 832025/059 Power Sensor A NRV-Z1 832279/013 Rohde & Schwarz 832279/013 Power Sensor B NRV-Z1 832279/015 Rohde & Schwarz 832279/015 Power Supply E3632A MY40003776 Agilent Power Supply PS-2403D - Conrad RF Step Attenuator RSP 833695/001 Rohde & Schwarz 833695/001 Rubidium Frequency MFS 002 Efratom Normal Signal Analyzer FSIQ26 FSIQ26 832695/007 Rohde & Schwarz 832695/007 Signal Generator SMP 03 833680/003 Rohde & Schwarz 833680/003 Signal Generator A SMIQ03B 834344/002 Rohde & Schwarz 834344/002 Signal Generator B SMIQ03B 832870/017 Rohde & Schwarz 832870/017 Signal Switching and SSCU 338826/005 Rohde & Schwarz Conditioning Unit Signalling Unit PTW60 PTW60 for TS8960 838312/014 Rohde & Schwarz 838312/014 System Controller PSM12 829323/008 Rohde & Schwarz 829323/008 Test report Reference: MDE_Siem_0617_FCCc Page 16 of 20

6 Photo Report Photo 1: Test setup for conducted measurements Photo 2: Test setup for radiated measurements Test report Reference: MDE_Siem_0617_FCCc Page 17 of 20

7 Setup Drawings Drawing 1: Setup in the Anechoic chamber. For measurements below 1 GHz the ground was replaced by a conducting ground plane. Test report Reference: MDE_Siem_0617_FCCc Page 18 of 20

8 Annex measurement plots 8.1 AC Mains conducted Op. Mode op-mode 1 Short Description: FCC Voltage Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 150.0 kHz 30.0 MHz 5.0 kHz MaxPeak 20.0 ms 9 kHz ESH3-Z5 Average Level [dBµV] 80 70 60 50 x x xx + ++ x x+ x + x x + + 40 + + x + 30 20 10 0 150k 300k 500k 1M 2M 3M 5M 7M 10M 30M Frequency [Hz] x MES Sie_0617_49_fin QP + MES Sie_0617_49_fin AV MES Sie_0617_49_pre PK MES Sie_0617_49_pre AV LIM FCC 15b QP volt Voltage QP Limit LIM FCC 15b AV volt Voltage QP Limit Test report Reference: MDE_Siem_0617_FCCc Page 19 of 20

8.2 Spurious radiated emissions Op. Mode op-mode 1 Short Description: FCC part 15 b Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 30.0 MHz 1.0 GHz 60.0 kHz MaxPeak 1.0 ms 120 kHz HL562 Level [dBµV/m] 80 70 60 50 40 x xxxx 30 x x 20 xxx 10 0 30M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] x MES Sie_0617_47_fin QP MES Sie_0617_47_pre PK LIM FCC part 15 b Field Strength QP Limit Test report Reference: MDE_Siem_0617_FCCc Page 20 of 20


Document Created: 2007-07-06 10:11:19
Document Modified: 2007-07-06 10:11:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC