ID Label Location

FCC ID: LDK-IR529WP

ID Label/Location Info

Download: PDF

FCCID_2532987

8 7 6 5 4 3 2 1
--- REVISION ---
APPROVE
17 REV DESCRIPTION ECO MECH MFG
01 INITIAL RELEASE CK JC

13 03 CHANGED LIGHTPIPE TORQUE, ADDED POWER CONN ORIENTATION VIEW CK JC
15 04 ADDED ITEM 24, 25, AND 26 CK JC
9
05 ADDED ITEM 28 CK JC
06 ADDED ITEM 29 CK JC
D 16 D
8
NOTES: (UNLESS OTHERWISE SPECIFIED)

1. THIS IS A COMPUTER GENERATED DOCUMENT.
ALL CHANGES MUST BE MADE IN THE MASTER
DATABASE ONLY.

2. SLIDE O-RING, ITEM 16, INTO THE LIGHTPIPE, ITEM 15.
5 INSTALL THE LIGPIPE ASSY, POWER CONNECTOR WITH NUT (SEE NEXT PAGE
14
24 FOR ORIENTATION), ITEM 12, PG13 PLUG, ITEM 14, ANTENNA CONN, ITEM
13
TO THE BOTTOM COVER, ITEM 1.
1
12 3. INSTALL MCX-MCX CABLE, ITEM 21, TO THE ANTENNA CONN,
ITEM 13. APPLY TIMS, ITEM 10 (7X), TO THE BOTTOM
9 COVER, ITEM 1. PLS REFER TO PAGE TO FOR TIM LOCATIONS.

4 INSTALL THE OTHER END OF THE MCX-MCX CABLE, ITEM 21,
4
7 TO THE MOTHERBOARD, ITEM 3. SLIDE THE MOTHERBOARD,
ITEM 3, INTO THE INTERFACE CARD, ITEM 4, AS SHOWN.
PLACE THE WHOLE ASSEMBLY INTO THE BOTTOM COVER.
STEP 1 TIGHTEN WITH SCREWS, ITEMS 8 (5X). PLACE THE
C 2 28 22 4 TIM, ITEM 10, RIGHT AT THE CENTER OF COPPER SQUARE ON THE
MOTHERBOARD, ITEM 3. PLACE TIMS, ITEM 22, ON TWO ROWS OF RESISTORS
C
ON THE INTERFACE CARD, ITEM 4, AS SHOWN.

5 ROUTE THE POWER CABLES, ITEM 12, INTO THE SLOT OF MIDPLATE,
ITEM 7, ENSURE ALL CABLES ARE ABOVE THE MID PLATE. INSTALL THE
4 10 MID PLATE, ITEM 7, TO THE BOTTOM COVER ASSEMBLY, ALIGN ONE SCREW,
ITEM 8, TO THE SMALLEST MIDPLATE MOUNTING HOLE, AS SHOWN.
TIGHTEN WITH THE REST OF THE SCREWS, ITEM 8 (5X). TIGHTEN 2
5 SCREWS, ITEM 8, TO THE INTERFACE CARD. APPLY INSULATOR, ITEM 28.

6. PLACE 3 TIMS, ITEM 9, TO THE SIDE OF THE MID PLATE. INSTALL POWER
SUPPLY UNIT, ITEM 5, TO THE MID PLATE WITH 4 SCREWS, ITEM 8.
3 INSTALL POWER ADAPTER, ITEM 22, TO THE POWER SUPPLY UNIT
(PSU), ITEM 5. INSTALL THE CRIMP CONNECTORS FROM THE POWER
CABLE, ITEM 12, TO THE LEADS, POWER ADAPTER, ITEM 22. PLS REFER
TO PAGE TWO FOR PIN OUT DETAILS. GENTLY PUSH ALL THE EXESSIVE
11 LENGTH CABLES INTO THE MIDPLATE SLOT. INSTALL THE PSU OUTPUT
CABLE, ITEM 5, TO THE INTERFACE CARD, ITEM 4. PLS REFER TO PAGE
2
FOR DETAILS. NEXT SECURE THE CABLE WITH A TIE WRAP, ITEM 23, TO
THE MIDPLATE. PLACE 3 TIMS, ITEM 9, TO THE PSU HEATSINK, AS SHOWN.

B 9. GENTLE PRESS THE GASKET, ITEM 11, INTO THE GROVE OF THE BOTTOM
COVER, ITEM 1. FINALLY, PUT BOTH OF THE TOP AND BOTTOM COVER
B
TOGETHER. TIGHTEN WITH 4 SETS OF BOLTS, ITEM 18, SPRING WASHERS,
ITEM 19 AND FLAT WASHER, ITEM 20. FINALLY, APPLY THE LABELS,
ITEM 25, 26, 27 AND 29 AS SHOWN IN PAGE TWO.
20
21 11. ASSEMBLY AND PARTS SHALL CONFORM TO MECH COSMETIC ACCEPTANCE
SPEC 95-0669-XX, AND MECH COSMETIC SPEC, 95-2733-XX.

19 12. REFER TO TABLE BELOW FOR TORQUE REQUIREMENT
ITEM # DESCRIPTION TORQUES [INLBF]
8 M3 SCREW 5-7
18 M8 BOLT 72-84
18 STEP 2 13 ANTENNA CONN 72-84
14 PG-13 PLUG 72-84
15 LIGHTPIPE 3.0-3.5
12 POWER CONN NUT 72-84
17 GORE VENT 5-7
UNLESS OTHERWISE SPECIFIED THIS DRAWING CONTAINS INFORMATION WHICH IS
THE PROPRIETARY PROPERTY OF CISCO SYSTEMS.
DIMENSIONS ARE IN INCHES: THIS DRAWING IS CONFIDENTIAL AND ITS
TOLERANCES: CONTENTS MAY NOT BE DISCLOSED WITHOUT
.XX # .01 PRIOR WRITTEN CONSENT OF CISCO SYSTEMS.

A .XXX # .005
ANGLES: # 1 APPROVAL DATE A
DES C. KHO 12/16/13
ENG C. KHO 12/16/13 REFDWG,FNLASY,BASE,BR-RE
MATERIAL: THIRD ANGLE PROJECTION MFG J. CHEW 12/16/13

STEP 3 SIZE DWG NO. REV
FINISH:
D 62-26778-02 06
SCALE 3/4 DO NOT SCALE DRAWING SHT 1 OF 2

8 7 6 5 4 3 2 1 CAD TYPE: PROE

8 7 6 5 4 3 2 1
--- REVISION ---
APPROVE
REV DESCRIPTION ECO MECH MFG

SEE SHEET 1

D D

NOTE: THE NOTH ON THE POWER CONNECTOR
IS FACING OPPOSITE EDGE OF THE CHASSIS

26 GROUND

C 25
C

26 CONSOLE

27

10

TEXT
ORIENTATION
GROUND WIRE (YELLOW/GREEN)

NEUTRAL WIRE (BLUE)
B 23
B
LIVE WIRE (BROWN)

26 MODEL/FCCID

PSU OUTPUT CABLE
TO INTERFACE BOARD.
26 COMPLIANCE

TIM LOCATIONS PSU PIN OUT TO POWER CABLE SCHEMATIC
29 ALTITUDE

ORIENTATION OF POWER INPUT CONN
&
A LABEL LOCATIONS A

SIZE DWG NO. REV

D 62-26778-02 06
SCALE 1/1 DO NOT SCALE DRAWING SHT 2 OF 2

8 7 6 5 4 3 2 1 CAD TYPE: PROE

Document Created: 2015-02-11 13:17:19
Document Modified: 2015-02-11 13:17:19

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC