User manual

FCC ID: KFR-ZL7432US

Users Manual

Download: PDF
FCCID_2325457

Operation Turn on or turn off two individual appliances that attached to ZL7432 by Z—Wave"" Interface Controller Federal Communications Commission Statement This equipment has follows with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferene by one of the following measures: The Ultimate in Security & Automation Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Installation & Operation Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inferference received, including interference that may cause undersired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this ZL 7432 IN equipment. ZL 7432 EU Limited Warranty Vision Guarantees that every In—Wall Switch module is free from physical defects in ZL 7432 RU material and workmanship under normal use for one year from the date of purchase. If ZL 7432 US the product proves defective during this one—year warranty period, Vision will replace it free of charge. Vision does not issue any refunds. This warranty is extended to the ZL 7432 IS original end user purchase only and is not transferable. This warranty does not apply to : (1) damage to units caused by accident, dropping or abuse in handling, or any negligent ZL 7432 JP use; (2) units which have been subject to unauthorized repair, taken apart, or otherwise modified; (3) units not used in accordance with instruction; (4) damages exceeding the ZL 7432 BR cost of the product; (5) transit damage, initial installation costs, removal cost, or reinstallation cost. For information on addional devices, plesae visit us at wwwvisionsecurity.com .w In—Wall Switch, 2 Relays 2l Tage tosoger se1z—74005

Introduction Note: Place antenna toward the surface and away from metal to get better signal. Thanks for choosing the Vision‘s In—Wall Switch module of the home automation device. This module is a Z—Wave"* enabled device (interoperable, two—way RF mesh networking technology) and is fully compatible with any Z—Wave"" enabled network. Every mains Live Neutral powered Z—Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate "RF dead—sports‘. Wall SW2 Z—Wave"" enabled devices displaying the Z—Wave"" logo can also be used with it + regardless of the manufacturer, and ours can also be used in other manufacturer‘s Antenna Wall SW1 Z—Wave * enabled networks. With special design, this module can fit into most of electronic box in the market. This madule will send On/Off signal to the appliance that attached to this module by receiving Z—Wave "* signal from controller. It also can control o LED LOAD1 two appliances independently. o L\ / Product Description and Specification Progran SW Specification: Package Content Protocol: Z—Wave"! (ZM3102N) 1pc ZL 7432 In—Wall Switch, Frequency Range: 865.22MHz (ZL7432IN) 2 Relays . 868.42MHz (ZL7432EU) 1pc Installation & Operation 869.00MHz (ZL7432RU) Manual 908.42MHz (ZL7432US) 2. For "Inclusion" in (adding to) a network: Put the Z—Wave"" Interface Controller 916.00MHz (ZL74321S) into "inclusion" mode, and following its instruction to add the ZL 7432 to your 920.00MHz (ZL7432JP) controller. To get in the "inclusion‘ mode, the distance between module and 921.42MHz (ZL7432BR) controlleris suggested to be in one meter. Turn on and turn off the wall switch that Operating Range: Up to 100 feet line of sight connects with ZL 7432 module 4 times to be included. (or press the Program SW 4 Operating Temp.: —15°C~ 60°C (5°F~140°F) times within 2 seconds to be included) Operating Voltage: 100VAC~240VAC For "Exclusion" from (removing from) a network: Put the Z—Wave"* Interface Resistive Load: Controller into "exclusion" made, and following its instruction to delete the ZL 7432 550W for 110VAG from your controller. Turn on and turn off the wall switch that connects with ZL 1100W for 220VAC 7432 module 4 times to be excluded. (or press the Program SW 4 times within 2 Z—Wave "" Command Class seconds to be excluded) COMMAND_CLASS_ASSOCIATION For Wall SW1, ZL 7432 will report the status of O/OFF after doing "Association‘. COMMAND_CLASS_MANUFACTURER_SPECIFIC However, Wall SW2 will only report the statusif Z—Wave "" Interface Controller COMMAND_CLASS_MULTICHANNEL_V3 support Multi Channel command, and send Get Command to ask ZL 7432 Wall SW COMMAND_CLASS_SWITCH_ALL 2 to report the status. COMMAND_CLASS_SWITCH_BINEARY mapping COMMAND_CLASS_BASIC User can use the following command class to control relay 1 and/or 2 in orderto COMMAND_CLASS_VERSION control the appliances that aftached to ZL7432 Installation For relay 1: Notice: If you are installing the entire Z—Wave"*" system for the first time, please refer to Status of "ON® (Binary Switch Set OxFF or wall switch ON) the installation guide of Z—Wave * Interface Controller before installing ZL7432 In—Wall Status of "OFF" (Binary Switch Set 0x00 or wall switch OFF) Switch Module. For relay 1 or 2: Please use Multi—Channel command class to control 1. Following the wiring diagram to instal ZL7432 according to your varied Resetto the factory default setting: Press and hold the Program SW before power requirements. on. 2.


Document Created: 2014-03-27 15:06:11
Document Modified: 2014-03-27 15:06:11
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC