MPE CALCULATIONS

FCC ID: KBCIX260PROAC860

RF Exposure Info

Download: PDF
FCCID_699482

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 Appendix D - Maximum Permissible Exposure Calculation D.1 REFERENCES Normative FCC CFR 47§1.1310 Reference Standard IEEE Std C95.1-1999 Procedure Reference FCC CFR 47§2.1091 D.2 LIMITS Frequency Power Density FCC CFR 47§1.1310 Table 1(b) 300 - 1500 MHz f/1500 mW/cm2 1500 - 100,000 MHz 1.0 mW/cm2 D.3 ENVIRONMENTAL CONDITIONS Temperature na Humidity na Barometric Pressure na D.4 MEASUREMENT EQUIPMENT SETUP The results described herein were determined by calculations, so no measurement MEASUREMENT EQUIPMENT equipment was used. The power measurements for each radio used in these CONNECTIONS calculations were made as described in Appendix A of this report. MEASUREMENT EQUIPMENT SETTINGS n/a D.5 DUT OPERATING DESCRIPTION Dual-Band The maximum GPRS RF conducted output power in each band used for these calculations was measured GPRS on Channel 251 for Cellular and Channel 661 for PCS. Dual-Band The maximum EDGE RF conducted output power in each band used for these calculations was measured EDGE on Channel 190 for Cellular and Channel 661 for PCS. Dual-Band The maximum UMTS RF conducted output power in each band used for these calculations was measured UMTS on Channel 4233 for Cellular and Channel 9400 for PCS. Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 37 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6 TEST RESULTS D.6.1 Calculations: Swivel Dipole Antenna (Max. Measured Conducted Power - Cellular GPRS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 848.80 (MHz) Maximum Peak Power at Antenna Input Terminal: 32.28 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain: 2.60 (dBi) SL= 0.57 (mW/cm^2) P= 422.6102 (mW) G= 1.82 (numeric) R = 10.40 (cm) S (mw/cm^2) at 20cm 0.15282675 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= P R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 38 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.2 Calculations: Swivel Dipole Antenna (Max. Measured Conducted Power - PCS GPRS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 1880.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 28.63 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain: 2.60 (dBi) SL= 1.00 (mW/cm^2) P= 182.3644 (mW) G= 1.82 (numeric) R = 5.14 (cm) S (mw/cm^2) at 20cm 0.065947658 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 39 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.3 Calculations: Swivel Dipole Antenna (Max. Measured Conducted Power - Cellular EDGE Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R = PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 836.60 (MHz) Maximum Peak Power at Antenna Input Terminal: 26.89 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain: 2.60 (dBi) SL= 0.56 (mW/cm^2) P= 122.1631 (mW) G= 1.82 (numeric) R = 5.63 (cm) S (mw/cm^2) at 20cm 0.044177321 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 40 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.4 Calculations: Swivel Dipole Antenna (Max. Measured Conducted Power - PCS EDGE Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 1880.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 25.73 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain: 2.60 (dBi) SL= 1.00 (mW/cm^2) P= 93.5276 (mW) G= 1.82 (numeric) R = 3.68 (cm) S (mw/cm^2) at 20cm 0.033822007 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 41 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.5 Calculations: Swivel Dipole Antenna (Max. Measured Conducted Power - Cellular UMTS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 1.00 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 846.60 (MHz) Maximum Peak Power at Antenna Input Terminal: 24.00 (dBm) Source-Based Time-Average Factor: 0.00 (dB) Antenna gain: 2.60 (dBi) SL= 0.56 (mW/cm^2) P= 251.1886 (mW) G= 1.82 (numeric) R = 8.03 (cm) S (mw/cm^2) at 20cm 0.090836286 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 42 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.6 Calculations: Swivel Dipole Antenna (Max. Measured Conducted Power - PCS UMTS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 1.00 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 1880.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 23.00 (dBm) Source-Based Time-Average Factor: 0.00 (dB) Antenna gain: 2.60 (dBi) SL= 1.00 (mW/cm^2) P= 199.5262 (mW) G= 1.82 (numeric) R = 5.38 (cm) S (mw/cm^2) at 20cm 0.072153826 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 43 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.7 Calculations: Vehicle-Mount Antenna (Max. Measured Conducted Power - Cellular GPRS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 848.80 (MHz) Maximum Peak Power at Antenna Input Terminal: 32.28 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain and Cable Loss: 1.11 (dBi) SL= 0.57 (mW/cm^2) P= 422.6102 (mW) G= 1.29 (numeric) R = 8.76 (cm) S (mw/cm^2) at 20cm 0.108442464 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 44 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.8 Calculations: Vehicle-Mount Antenna (Max. Measured Conducted Power - PCS GPRS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 1880.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 28.63 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain and Cable Loss: 0.20 (dBi) SL= 1.00 (mW/cm^2) P= 182.3644 (mW) G= 1.05 (numeric) R = 3.90 (cm) S (mw/cm^2) at 20cm 0.037948916 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 45 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.9 Calculations: Vehicle-Mount Antenna (Max. Measured Conducted Power - Cellular EDGE Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 836.60 (MHz) Maximum Peak Power at Antenna Input Terminal: 26.89 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain and Cable Loss: 1.11 (dBi) SL= 0.56 (mW/cm^2) P= 122.1631 (mW) G= 1.29 (numeric) R = 4.74 (cm) S (mw/cm^2) at 20cm 0.031347245 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 46 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.10 Calculations: Vehicle-Mount Antenna (Max. Measured Conducted Power - PCS EDGE Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of interest relative to an isotropic radiator R= PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 0.25 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 1880.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 25.73 (dBm) Source-Based Time-Average Factor: -6.02 (dB) Antenna gain and Cable Loss: 0.20 (dBi) SL= 1.00 (mW/cm^2) P= 93.5276 (mW) G= 1.05 (numeric) R = 2.79 (cm) S (mw/cm^2) at 20cm 0.019462534 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 47 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.11 Calculations: Vehicle-Mount Antenna (Max. Measured Conducted Power - Cellular UMTS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of 2 interest relative to an isotropic radiator R = PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 1.00 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 846.60 (MHz) Maximum Peak Power at Antenna Input Terminal: 24.00 (dBm) Source-Based Time-Average Factor: 0.00 (dB) Antenna gain and Cable Loss: 1.11 (dBi) SL= 0.56 (mW/cm^2) P= 251.1886 (mW) G= 1.29 (numeric) R = 6.76 (cm) S (mw/cm^2) at 20cm 0.064455409 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 48 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.6.12 Calculations: Vehicle-Mount Antenna (Max. Measured Conducted Power - PCS UMTS Mode) Prediction of MPE Limit OET Bulletin 65, Edition 97-01 Equation from page 18 S = PG S= power density P= power input to the antenna 4 πR 2 G= power gain of the antenna in the direction of 2 interest relative to an isotropic radiator R = PG R= distance to the center of radiation of the antenna 4π S SL= power density limit Ratio of Time On versus Total Transmit Time 1.00 Choose ENTER Occupational/Controlled General Population/Uncontrolled Tx Frequency: 1880.00 (MHz) Maximum Peak Power at Antenna Input Terminal: 23.00 (dBm) Source-Based Time-Average Factor: 0.00 (dB) Antenna gain and Cable Loss: 0.20 (dBi) SL= 1.00 (mW/cm^2) P= 199.5262 (mW) G= 1.05 (numeric) R = 4.08 (cm) S (mw/cm^2) at 20cm 0.041520193 Formulae: S = PG where: S = Power Density Limit 4πR2 P = Power Output of the Device G = Numeric Antenna Gain R= PG R = Distance from Antenna 4πS Source-Based Time-Average Factor = 10 * log (Time On / (Time On + Time Off)) Power Output of the Device (W) = 10 * log (RF Output Power (dBm) + Source-Based Time Average Factor (dB)) Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 49 of 51

Test Report Serial No.: 061506KBC-T757-E24G Report Issue Date: August 24, 2006 Date(s) of Evaluation: June 21 - July 27, 2006 Report Revision No.: Revision 1.0 Test Standard(s): FCC 47 CFR §2, §22H, §24E Industry Canada RSS-132, RSS-133 Test Lab Registration(s): FCC Lab Registration #714830 Industry Canada Lab File #3874 D.7 PASS/FAIL In reference to the results outlined in D6 the DUT passes the requirements as stated in the reference standards as follows: 1) The DUT must comply with the minimum spacing requirement of 20 cm to ensure an exposure of not more than f/1500 mW/cm2 for frequencies between 300 and 1500 MHz and 1 mW/cm2 for frequencies between 1500 and 100,000 MHz. D.8 SIGN-OFF I attest to the accuracy of the data. All measurements reported herein were performed by me and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements. Spencer Watson EMC Manager Celltech Labs Inc. June 27, 2006 Date Company: Itronix Corporation FCC ID: KBCIX260PROAC860 Model(s): IX260PROAC860 DUT Type: Laptop PC with Sierra Wireless AC860 Dual-Band GSM/GPRS/EDGE/UMTS PCMCIA Modem 2006 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the prior written permission of Celltech Labs Inc. Page 50 of 51


Document Created: 2006-08-24 14:41:58
Document Modified: 2006-08-24 14:41:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC