User Manual

FCC ID: K4ER100TBQ

Users Manual

Download: PDF
FCCID_4130514

ENFORCER Wireless Help Button Changing the Battery: The Wireless Help Button has a multi-colored LED that illuminates blue when the button is pressed. When the battery begins to run low, the LED will illuminate red. To change the battery: 1. Remove the two screws from the front of the plate and remove the plate from the back box. 2. Remove the battery clip from the 9V battery and remove the battery from the bracket. 3. Place the new battery in the bracket and snap the battery clip to the new battery. 4. Test the unit with the new battery. The LED should illuminate blue. RM-R100-TBQ 5. Put the plate back in the back box and secure it to the back box using the screws on the front. Troubleshooting:  Check battery connection SD-862M-GWSQ LED does not light Wireless Help Button  Replace 9V battery  Ensure Wireless Help Button is not housed in a metal box LED lights blue, but does not  Test Wireless Help Button closer to the receiver activate lock  Clear codes from receiver and re-learn wireless transmitter code Also Available from ®: Manual 2-Channel RF Receiver 1-Button Handheld RF Transmitter Room Monitor Kit SK-910RB2Q SK-919TP1H-BUQ RM-R100-KB1Q IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes. FCC COMPLIANCE STATEMENT FCC ID: K4ER100TBQ THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Notice: The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration, Features: improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment  Built-in RF transmitter:  ABS Plastic single-gang plate with surface is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s - Powered by 9VDC (battery included) mount back box option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property  Clear 2" square button damage of any kind to the purchaser or anyone else. - Range up to 250ft (76m)*, 433.92MHz - Over 68 billion (6.8x1010) possible codes  "Push for Help" message plate included NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks - LED to indicate transmission and low battery  Requires RM-R100-KB1Q, or SK-910 are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2018 SECO-LARM U.S.A., Inc. All (433.92MHz) series receiver rights reserved.  Desktop or wall mounted *Actual operating range will vary greatly depending on the installation and operating environment. ® U.S.A., Inc. PITSW1 16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com Order Part# 763-190% Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com MI_RM-R100-TBQ_181211.docx ® 4 SECO-LARM U.S.A., Inc.

ENFORCER Wireless Help Button ENFORCER Wireless Help Button Introduction: Installation: 1. Find a suitable location for the Wireless Help Button. The ENFORCER Wireless Help Button can be used to wirelessly expand the Room Monitor (RM-R100-KB1Q) with a service/help button. The button is perfect for placing on a desktop, mounting on NOTE: Do not house in a metal box as this will greatly reduce the range. walls, or any other location where it is difficult to run wires. The Wireless Help Button combines the very 2. The Wireless Help Button can either be wall mounted (taller side of back box on bottom), or placed best of SECO-LARM, flexible wireless solutions and reliable access control. on a desktop (taller side of back box on top). 3. Test the operation of the Wireless Help Button in the location where it will be installed before Parts List: finalizing the installation. 1x Wireless Help Button 1x Back box 2x Wall plate screws NOTE: The Wireless Help Button needs to be programmed into the RM-R100-RB1Q or a 2x Mounting screws 2x Wall anchors 1x 9V Alkaline battery SK-910 (433.92MHz) series receiver before testing. See the receiver manual for transmitter 4x Adhesive rubber feet 1x Manual learning procedure. 4. Ensure the battery clip is securely connected, mount the Wireless Help Button in the back box Specifications: according to the appropriate orientation stated above, and secure it with the two included screws. Apply the included adhesive rubber feet for desktop applications. Operating frequency 433.92MHz Operating voltage 9VDC Changing the Message Plate: Maximum range 250' (76m)* You can easily print your own message plate on very thin card stock, no Fig. 1 Battery life Up to four (4) years (60 uses per day) thicker than the included message plate, and trim to 17/8" (37mm) square. Desktop 45/8"x27/8"x17/8" (117x73x48 mm) Your Message Dimensions NOTE: Thicker card stock will not allow the transparent lens to fully seat. Custom Plate Wall mount 45/8"x27/8"x2" (117x73x50 mm) Message Weight 6-oz (178g) 1. Use the tip of a very thin screwdriver to pry off the transparent lens *Actual operating range will vary greatly depending on the installation and operating environment. over the message plate (see Fig. 1). 2. Replace the current plate with the desired message plate, keeping the Transparent Overview: spacer plate in place. lens Spacer 9V Alkaline 3. Check that message plate orientation is correct. Plate battery 4. Carefully snap the lens assembly back on. LED Indicator Off: No transmission RM-R100-TBQ Sample Applications: Battery clip Push Blue: Transmitting for Help Red: Low battery Basic Installation with Room Monitor Kit (RM-R100-KB1Q) Request Sensor/Transmitter Sensor/Transmitter Indicator/Receiver Light/Buzzer RM-R100-TLQ RM-R100-TLQ RM-R100-RB1Q and RF receiver button (not included) Indicator/Receiver RM-R100-RB1Q Dimensions: 1 2 15/16" Room occupied Push 45/8" Wireless Help Button Wireless Help Button (24mm) (117mm) 17/8" for Help RM-R100-TBQ RM-R100-TBQ 17/16" (48mm) (36mm) Room occupied – indicator/receiver LED is lit. Room occupied – remote indicator/receiver LED is lit. Wireless pushbutton pressed – indicator/receiver Wireless pushbutton pressed – light/buzzer connected to a 45/8" 2" 13/4" 27/8" 433.92MHz RF receiver outside door is triggered and remote (50mm) LED flashes and/or buzzer sounds (117mm) (45mm) (73mm) indicator/receiver LED flashes and/or buzzer sounds Attendant uses wireless remote (not included) to reset the indicator flashing LED and/or buzzer. Attendant uses wireless pushbutton (or wireless remote, not Desktop Wall mount included) to reset the Indicator flashing LED and/or buzzer. 2 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 3


Document Created: 2019-03-21 21:53:45
Document Modified: 2019-03-21 21:53:45
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC