Users Manual

FCC ID: K4E266CQ

Users Manual

Download: PDF
FCCID_3939070

ENFORCER Wireless Video Door Phone Also Available from SECO-LARM®: 2-Wire Hands-Free Additional Monitor Additional Camera Video Door Phone DP-266-1C3Q DP-266-M3Q DP-266-CQ DP-234Q Wireless Video Door Phone 2-Wire Color CBA® Wireless Video Door Phone Wireless Intercom Alert System Manual DP-222Q DP-T100-2Q RA-4961-K1Q IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes. FCC COMPLIANCE STATEMENT DP-266-M3Q FCC ID: K4E266M3Q DP-266-CQ FCC ID: K4E266CQ Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna. *  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Features: WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal  Wireless operation – camera and monitor can  Camera includes a built-in PIR sensor that service for one (1) year from the date of sale to the original customer. SECO-LARM's obligation is limited to the repair or operate from up to 492ft (150m)** away activates the camera and takes photos of the replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,  Remotely and securely talk to visitors and visitor when they approach improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment unlock doors or gates via the monitor  Monitor includes a kickstand and a charging base is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of  Lightweight monitor can be carried around the  Camera powered by 9~16 VAC/5~16 VDC SECO-LARM and the purchaser's exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property premises while talking to the visitor  Monitor front door at any time damage of any kind to the purchaser or anyone else.  Connect up to two additional monitors and one  Egress input NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM additional camera*  170° wide field of view reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks  Intercom calling between paired monitors*  Adjustable camera pan and tilt angle—up to 20° are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2018 SECO-LARM U.S.A., Inc. All rights reserved.  Camera has built-in IR LEDs for nighttime from centerline in any direction—to allow for operation mounting variations SECO-LARM ® U.S.A., Inc. ® *Additional monitors and camera sold separately. PICKN1 16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com **Line-of-sight range. Actual range may vary depending on the installation and operating environment. Phone: (949) 261-2999 | (800) 662-0800 Email: sales@seco-larm.com MI_DP-266-1C3Q_180628.docx ® 16 SECO-LARM U.S.A., Inc.

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone Table of Contents: Tamper Alarm: Introduction ................................................................ 2 Programming and Using the The tamper alarm activates anytime the camera is removed from the bracket, warning the user of Parts List.................................................................... 2 On-Screen Display...........................................9~10 Specifications ............................................................ 3 Programming the Advanced Settings ................10~11 possible vandalism. The tamper alarm will sound on the camera and any connected monitors. Overview.................................................................... 3 Operating the Wireless 1. To disable the tamper alarm if no monitors are paired with the camera: Display Overview ....................................................... 4 Video Door Phone .........................................12~13 a. Return the camera to the bracket. Installation Notes ....................................................... 4 Resetting the Camera and b. If the alarm persists, unplug the camera and remove the battery. Camera Wiring Diagram ............................................ 5 Pairing a First Monitor....................................13~14 c. Return the camera's battery and reconnect it to power. Sample Application .................................................... 5 Pairing Additional Monitors or Cameras .................. 14 Installation – Camera ................................................ 6 Tamper Alarm .......................................................... 15 2. To disable the tamper alarm if one or more monitors are paired with the camera: Installation – Monitor ............................................. 6~7 Troubleshooting ....................................................... 15 a. Repeatedly press the "OK" button on all paired monitors. On-Screen Display Features ..................................... 8 Warranty ................................................................... 16 b. If the alarm persists, unplug the camera and remove the battery. c. Unplug each monitor and remove each monitor's battery. Introduction: d. Return the camera's battery and reconnect it to power. The ENFORCER Wireless Video Door Phone is a convenient and secure way to monitor and e. Insert each monitor's battery and reconnect each monitor to power. control an entryway, such as a door or gate, from up to 492 feet (150 meters) away. 3. To permanently disable the tamper alarm, see the "Alarm setting" section in "Programming When a guest or visitor presses the doorbell button on the camera unit, the homeowner can use the Advanced Settings," pg. 11. one of up to three lightweight, wireless LCD monitors to see whom is requesting entry, speak with Troubleshooting: the caller, take a photo, and decide whether or not to grant entry. The video door phone can be  Make sure the "ON/OFF" or "OK" button was pressed to wake expanded with up to two additional monitors and one additional camera. If multiple monitors are set the monitor up, then the system can also be used as an intercom system between each monitor. The monitor's screen is blank  Make sure the monitor's battery is charged  Plug the charger directly into the monitor Parts List:  Remove the battery from the battery compartment and clean DP-266-1C3Q DP-266-M3Q both the battery contacts and the monitor's connection contacts Complete Kit Additional Monitor Unit  Make sure the kickstand is extended when placing in the 1x Monitor (DP-266-M3Q)* 1x Monitor (DP-266-M3Q)** The monitor is not charging charger stand 1x Camera (DP-266-CQ)* 1x Monitor charging stand  Make sure the power adapter is correctly connected to the 1x Monitor charging stand 1x Monitor kick stand charger stand 1x Monitor kick stand 1x AC Power adapter with USB port (for monitor)  Connect the power adapter directly to the monitor 1x AC Power adapter with USB port 1x USB Cable (for monitor) 1x Monitor battery  Check that the volume is turned up 1x USB Cable 1x Manual The monitor does not ring  Check that the monitor is in standby mode 1x Monitor battery  Check that the monitor is placed in the mounting bracket 1x Camera mounting hood bracket DP-266-CQ 1x AC Power adapter with DC plug The monitor cannot connect to the  Check that the monitor has been paired with the camera (for camera) Additional Camera Unit camera  Check that the monitor is within range of the camera 1x DC Jack with pigtail 1x Camera (DP-266-CQ)** 1x Camera battery 1x Camera mounting hood bracket  Adjust the monitor's display brightness 3x Camera mounting screws 1x AC Power adapter with DC plug (for camera)  Clean the camera's lens using a soft, clean cloth The monitor's screen image quality 3x Camera mounting screw anchors 1x DC Jack with pigtail  Change the position of the camera is poor 1x Camera screw 1x Camera battery  Move the monitor away from potential sources of interference 1x Camera screw cover 3x Camera mounting screws (microwaves, television, lamps, etc.) 1x Manual 3x Camera mounting screw anchors 1x Camera screw  Make sure the user is pressing the "Menu/Unlock" button when 1x Camera screw cover in two-way communication (the microphone icon is lit and does The monitor is unable to activate the 1x Manual not have an "X" through it) camera's relay *The DP-266-1C3Q included monitor and camera are paired by default.  Check the wiring between the camera and the optional door **Additional monitors and cameras are not paired by default. See "Pairing Additional Monitors or Cameras" on pg. 14. locking device 2 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 15

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone Resetting the Camera and Pairing a First Monitor (continued): Specifications: 3. Reconnect the power wires and return the camera to the bracket. Camera Monitor 4. Press the doorbell button on the camera to confirm the connection. Type Color camera Display 33/8" (86mm) TFT Chip CMOS 5VDC (adapter) or Operating voltage Resolution 480 TV Lines 3.7VDC (battery) Pairing Additional Monitors or Cameras: Lens 2mm Current Active 370mA@3.7VDC Field of view 170° draw Standby 5mA@3.7VDC NOTE: By default, the monitor in the DP-266-1C3Q Complete Kit is paired with the camera. Camera angle adjustment Up to 20° any direction Battery Active ~2.5 Hours These instructions apply to pairing a second or third monitor, or a second camera. Operating voltage 9~16 VAC/5~16 VDC life Standby ~7 Days Relock delay 3/6/8 Seconds Operating frequency 2406~2480 MHz To pair an additional monitor: Relay output 3A@250VAC/30VDC Wireless range 492' (150m)* 1. Put the first monitor into pairing mode: Current Active 300mA@12VDC 5"x33/8"x7/8" Dimensions draw Standby 15mA@12VDC (127x85x22 mm) a. Select "Give code" from the "Pairing" option in the "Settings" menu. Battery Active ~7 Hours Weight 3.9-oz (110g) 2. Put the second monitor in pairing mode: life Operating temperature 32°~104° F (0°~40° C) Standby ~60 Days a. Select "Receive code" from the "Pairing" option in the "Settings" menu. IR LED Range 5' (1.5m) b. The second monitor will display "Success" and beep three times. IR LED Frequency 940nm NOTE: The first monitor will timeout automatically after ~20 seconds. PIR Detection range 9' (3m) PIR Detection angle 60° c. Press "Exit" on the first monitor to exit pairing mode. Dimensions 511/16 "x31/8"x115/16" 3. Press the doorbell button on the camera to test the connection. (with bracket) (144x80x50 mm) a. Answer the call from the newly paired monitor to confirm the connection. Weight 4.3-oz (122g) *Line-of-sight range. Actual range may vary depending on the 4. To pair a third monitor, use the second monitor to "give code". Operating temperature 14°~122° F (-10°~50° C) installation and operating environment. NOTE: Up to three total monitors can be learned to the system. Overview: NOTE: The intercom feature will not function until the connection is confirmed by the Camera: new monitor. Camera angle To pair an additional camera: adjustment joystick Camera 1. Put the camera into pairing mode: Wiring connections IR LEDs (see pg. 5) PIR Sensor a. Remove the camera from the bracket. Reset b. If the tamper alarm is active then the alarm will begin to sound. Reset button i. Disconnect power from the camera by removing the battery and disconnecting the Speaker power wiring. Battery cover Status LED ii. Replace the battery. Doorbell c. Use a paper clip or other small object to press and hold the camera's reset button for Microphone seven to eight seconds. The camera will beep once around four seconds and twice USB Connector around eight seconds. Monitor: (not used) NOTE: The camera will remain in pairing mode for ~15 seconds before Charging automatically exiting. indicator 2. Put any monitor in the system into pairing mode: Volume up/down ON/OFF Button: a. Select "Give code" from the "Pairing" option in the "Settings" menu. 33/8" (86mm) - Turn monitor 3. The camera will beep three times to indicate successful pairing. ON/OFF 4. Press "Exit" on the monitor to exit pairing mode. - Standby mode 5. Reconnect the power wires and return the camera to the bracket. Status LED OK/Talk 6. Press the doorbell button on the camera to confirm the connection. Up MENU Menu/Unlock USB Connector OK Down/Photo EXIT Exit/View (Mini-B) Microphone 14 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 3

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone Display Overview: Operating the Wireless Video Door Phone (continued): Communicating between monitors NOTE: The Wireless Video Door Phone system can be set up with up to 2 cameras and 3 monitors. If multiple monitors are set up, then the system can be used as an intercom : ID – Displays the monitor ID number between each monitor. To pair additional monitors see "Pairing Additional Monitors or : Signal Strength – Displays the wireless signal strength Cameras," pg. 14. : Communication Mode – Displays current communication mode Intercom feature with two monitors: – Bell indicates an incoming call 1. Make sure both monitors are powered ON. – Crossed out microphone indicates one-way communication 2. Press the "OK" or "Power" button to turn the monitor's display on. – Microphone indicates two-way communication 3. Press the "OK" button to call the other monitor. : Message – Displays when there is a message due to a missed call 4. To accept the call, the other monitor's user must press their "OK" button. : PIR – Displays when the PIR sensor is turned on 5. Press the "OK" button again when finished with the call. : Photo – Displays when a photo is taken NOTE: The intercom feature will automatically timeout after 60 seconds. : Relay – Displays while the relay is active Intercom feature with three monitors: : Alarm – Displays when the tamper alarm has been activated 1. Make sure all monitors are powered ON. : Monitor volume – Displays the current monitor volume 2. Press the "OK" or "Power" button to turn the monitor's display on. : Monitor Battery: Displays the current monitor station battery level NOTE: Each paired monitor will have an identification number in the top left corner (1, 2, or 3). : Camera Battery: Displays the current camera station battery level 3. Press the "Up" button to call the next highest ID monitor. 4. Press the "Down" button to call the next lowest ID monitor. Installation Notes: 1. Unpack the video door phone and note the included parts.  If monitor 1 is calling monitor 2, the user would press the "Up" button. 2. Read this manual thoroughly. A clear understanding of the manual will make installation and  If monitor 3 is calling monitor 2, the user would press the "Down" button. operation much easier.  If monitor 3 is calling monitor 1, the user would press the "Up" button. 3. Find a good location to mount the monitor and camera. Approximately 5ft (1.5m) above the 5. Press the "OK" button when finished with the call. ground is optimal, where the visitor would stand approximately 2.5~5 ft (0.8~1.5 m) from the camera. Note that the camera tilt and pan angle can be adjusted up to 20° from centerline to Resetting the Camera and Pairing a First Monitor: compensate for less than optimal situations (see below). 4. Avoid mounting the camera or monitor near sources of strong electromagnetic signals or other NOTE: By default, the monitor in the DP-266-1C3Q Complete Kit is paired with the camera. electronic devices that may cause interference. These instructions apply to resetting the camera and monitor system. 5. Avoid mounting the camera in direct sunlight or exposing the camera to strong vibrations, direct rain, or moisture, which could result in damage to the camera. Strong backlight or reflection 1. Put the camera into pairing mode: may degrade the resulting video image. a. Remove the camera from the bracket. 6. The monitor and camera contain no user-serviceable parts. Opening them may damage b. If the tamper alarm is active then the alarm will begin to sound. sensitive components and will void the warranty. i. Disconnect power from the camera by removing the battery and disconnecting the Camera with No Tilt Camera Tilted power wiring. ii. Replace the battery. c. Use a paper clip or other small object to press and hold the camera's reset button for 115º three to four seconds. A single beep indicates the camera is in pairing mode. 115º NOTE: The camera will remain in pairing mode for ~15 seconds before automatically exiting. Up 20º 2. Pair the first monitor to the camera: 170º 170º a. Select "Match code" from the "Pairing" option in the "Settings" menu. Left 20º b. The monitor will display "Success" and the monitor and camera will beep three times. 4 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 13

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone Operating the Wireless Video Door Phone: Camera Wiring Diagram: Communicating with the camera Request entry: COM 6 1. Press the doorbell button on the camera. The indoor monitor will ring and display an image Relay N.C. 5 from the camera. The monitor will also display a bell icon. Output N.O. 4 2. Wait for the indoor user to accept the call and activate the onboard relay as necessary. Reset Egress input (N.O., –) 3 (–) 2 ON/OFF: 9~16 VAC/  Turn monitor 5~16 VDC (+) 1 ON/OFF  Standby mode OK/Talk 1. Positive (+) power input – Connect to the red wire of the included AC adapter or to the positive Up MENU Menu/Unlock wire of the doorbell's power supply. OK 2. Negative (-) power input – Connect to the black wire of the included AC adapter or to the Doorbell Down/Photo EXIT Exit/View negative wire of the doorbell's power supply. 3. Egress (N.O.) negative input – Connect to an optional N.O. egress device. The egress device will activate the relay for the same length as the lock delay. (See the "Unlocking duration" Receive a visitor: section in "Programming the Advanced Settings," pg. 11). 1. If a visitor presses the doorbell button on the camera, the monitor's display turns ON and the 4. N.O. (Normally opened) output – Wire to the lock device for fail-secure operation. monitor sounds the chosen ring tone. 5. N.C. (Normally closed) output – Wire to the lock device for fail-safe operation. 6. Common output – Wire to the power supply of the lock device. 2. Press the "OK" button to accept the call. The bell icon will change to a microphone icon. 3. Press the "Menu/Unlock" button on the monitor to activate the camera's onboard relay. NOTE: For 16VAC doorbell installation, wire directly from the doorbell's transformer. 4. Press the “Exit/View" button to mute the monitor (the camera station can still be heard on the Sample Application: indoor monitor). 5. Press the "Down/Photo" button on the monitor to take a manual photo. Electric strike power supply 6. Press the "Volume up/down" button to adjust the audio level. COM 7. Press the "OK" button when finished with the call. 1 2 3 4 5 6 N.C. N.O. Fail-secure View and/or talk to a visitor who has not pressed the doorbell button on the camera: Egress input (N.O., -) electric strike (–) 1. Press the "OK" or "Power" button to turn the monitor’s display ON. (+) PUSH 2. Press the "Exit/View" button to monitor the camera station. TO Request-to-exit plate EXIT NOTE: If multiple cameras are connected then use the "Up" or "Down" button to select the Camera Negative (-) (black wire) desired camera station to monitor. Press "OK" to connect to the selected camera. To the included AC adapter or 3. The user can now view and hear the camera station. The microphone icon will have an "X" Positive (+) (red wire) the doorbell's transformer through it.  The camera is connected to its included AC adapter. 4. Press the "Exit/View" button to activate two-way communication. The microphone's "X" will  The egress input is connected to a Request-to-Exit Plate. The homeowner can exit the be removed. premises by pressing this button. 5. To unlock the optional electronic door lock, press the "Menu/Unlock" button to activate the relay.  The N.O. (normally open) output is wired to an electric lock. The camera and the 6. Press the "Down/Photo" button to take a manual photo. Request-to-Exit Plate both activate the strike, allowing entry or egress. 7. Press the "OK" button when finished with the call.  The electric lock's power supply is wired to the COM (common) output. 12 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 5

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone Installation – Camera: Programming the Advanced Settings (continued): 1. Position the camera so the area to be monitored is easily visible, Unlocking duration: optimally 5ft (1.5m) above the ground. Do not position the camera in 1. Select "Unlocking duration" and press the "OK" button. direct sunlight, or where it will be exposed directly to rain or snow. 2. Select from 3, 6, or 8 seconds and press the "OK" button. NOTE: For best results, the visitor should stand 2.5~5 ft (0.8~1.5 m) 5ft NOTE: If multiple cameras are paired to the monitor then select the desired camera. away from the camera. (1.5m) 3. The monitor will connect to the desired camera. 2. Cut a hole large enough to run the min. 21AWG 2-conductor wire to 4. Press the "OK" button to confirm. the door unlock device through the wall, as well as to the included NOTE: A single beep from the camera indicates 3 seconds, a double beep indicates 6 power supply. 3. Mount the camera bracket to the wall with three screws. Use screw seconds, and a triple beep indicates 8 seconds. anchors if the bracket is mounted on drywall or brick. Pairing: 4. Run the 2-conductor wire from the camera, through the wire hole in 33/4" See the "Resetting the Camera and Pairing a First Monitor" and "Programming Additional Monitors the bracket, to the optional door unlock device. (96mm) or Cameras" sections on pgs. 13~14 for information regarding the "Pairing" setting. 5. Install the rechargeable lithium ion battery into the camera. The battery will act as a backup power source in case of a power outage. Alarm setting: 6. Connect the AC adapter (see "Camera Wiring Diagram," pg. 5). 7. Install the monitor battery (see below) and turn on the camera and 1. Select "Alarm setting" and press the "OK" button. monitor. If the camera is not in the bracket, the tamper alarm will 2. Select "On" or "Off" to turn the tamper alarm on or off and press the "OK" button. sound. Press the "OK" button on the monitor repeatedly to disable 21/8" (54mm) NOTE: If multiple cameras are paired to the monitor then select the desired camera. the tamper alarm. 3. The monitor will connect to the desired camera. 8. Experiment with the camera angle using the joystick on the back of 4. Press the "OK" button to confirm. the camera to adjust the direction of the camera while viewing the Camera NOTE: A single beep from the camera indicates the tamper alarm has been turned OFF. image on the monitor. Angle A double beep indicates the tamper alarm has been turned ON. 9. Mount the camera into the bracket: Adjustment Reset  Push the top of the camera into the top of the bracket. Joystick Version:  Push the bottom of the camera into the bottom of the bracket. 1. Select "Version" and press the "OK" button.  Screw in the bottom of the camera to fix the camera into the 2. View the version number. bracket and push the plastic screw cover into the bottom of the bracket, over the screw. NOTE: Do not block the PIR sensor on the camera. Installation – Monitor: Install the monitor battery: Remove the battery cover on the back of the monitor and insert the included BP-6M lithium-ion battery. BP-6M 6 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 11

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone Programming and Using the On-Screen Display (continued): Installation – Monitor (continued): Programming the time and date: Recharge the monitor battery: 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. There are two ways to recharge the monitor battery. 2. Highlight the "Time" icon and press the "OK" button to enter the "Time" screen. 1. Place the 2. Plug the charger directly into the monitor. 3. Use the "Up" and "Down" buttons to adjust the value. Use the "Menu/Unlock" button to move to monitor into the the next value. monitor charger 4. Press the "OK" button when finished programming to go back to the on-screen display menu. stand and plug NOTE: The time is set in 24-hour time format. the charger into the stand. Programming the ringer: 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. 2. Highlight the "Ring" icon and press the "OK" button to enter the "Ring" screen. MENU OK 3. Use the "Up" and "Down" buttons to select one of four ring tones: Telephone (default), Doorbell, EXIT Für Elise, or Jingle Bells. 4. Press the "OK" button when finished programming to go back to the on-screen display menu. Programming the language: 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. Turn monitor ON: 2. Highlight the "Language" icon and press the "OK" button to enter the "Language" screen. ON/OFF Hold the "ON/OFF" button for 3 seconds. The monitor will turn 3. Use the "Up" and "Down" buttons to select a language: English (default), German, Spanish, ON with the ENFORCER screen. French, Russian, or Chinese. 4. Press the "OK" button when finished programming to go back to the on-screen display menu. Standby mode: If the display is OFF, press the "ON/OFF" button momentarily to leave standby mode and turn the display ON. The red Programming the Advanced Settings: indicator LED will flash once every three seconds in 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. standby mode. 2. Highlight the "Setup" icon and press the "OK" button to enter the "Setup" screen. Low battery: 3. Use the "Up" and "Down" buttons to select the advanced settings menu. When the battery is low (indicated by 1 or 0 bars on the 4. Press the "OK" button to enter the selected advanced settings menu. display's battery icon), the red indicator LED will start to flash once per second. Battery Motion detection: Turn monitor OFF: level 1. Select "Motion detection" and press the "OK" button. While the monitor's display is ON, hold the "ON/OFF" button indicator 2. Select "Off" or "On" to turn the PIR function off or on and press the "OK" button. for 3 seconds and the Shutdown menu will come up. Select NOTE: If multiple cameras are paired to the monitor then select the desired camera. Standby/ "YES" to turn the monitor OFF. 3. The monitor will connect to the desired camera. Low 4. Press the "OK" button to confirm. battery OK MENU EXIT NOTE: A single beep from the camera indicates motion detection has been turned OFF. indicator A triple beep indicates motion detection has been turned ON. Backlight time: 1. Select "Backlight time" and press the "OK" button. 2. Use the "Up" or "Down" buttons to select a backlight time between 10~60 seconds. 3. Press the "OK" button to confirm. 10 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 7

ENFORCER Wireless Video Door Phone ENFORCER Wireless Video Door Phone On-Screen Display Features: Programming and Using the On-Screen Display: Photos – View and delete photos taken by the camera station. There are four different 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. types of photos 2. Use the "Up" and "Down" buttons to move the cursor up or down. Use the "Menu/Unlock" button M – Photos taken by the user manually (1 photo taken). to move the cursor to the right. A – Photos taken by the camera station automatically when the doorbell button 3. To select a Menu option, highlight the option and press the "OK" button. is pressed (1 photo taken). 4. To exit the on-screen display, press the "Exit" button. T – Photos taken by the camera station automatically when the unit is removed NOTE: If there is no activity, the monitor will exit programming mode and the display will turn off in from the bracket and the tamper alarm activates (4 photos taken). 35 seconds. P – Photos taken by the camera station automatically when the PIR function is activated (3 photos taken). Viewing and deleting photos: 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. 2. Highlight the "Photo" icon and press the "OK" button to enter the "Photo" screen. Messages – View photos from missed calls, same as "Automatic" photos. 3. Use the "Up" and "Down" buttons to select the photo to be viewed. NOTE: Photos are saved with the following format: "X-HHMMSS-YYMMDD.jpg" with "X" being the type of photo, "HHMMSS" being the time the photo was taken, and "YYMMDD" being the date the photo was taken. Time – Set the time and date. 4. Press the "OK" button and select from "View," "Delete," or "Delete All." a. Press "View" to view a photo. b. Press "Delete" to delete the selected photo (after an additional prompt). c. Press "Delete All" to delete all photos (after an additional prompt). Ring – Choose from four different ring tones (Telephone, Doorbell, Für Elise, or Jingle 5. Once viewing a photo, press the "Up" or "Down" buttons to cycle through other photos. Bells) and set ring volume (six volume levels). 6. Press the "OK" button to either delete or exit the photo viewing mode and go back to the on-screen display menu. NOTE: The monitor can save up to 240 photos. Photos are saved in a "first-in, first-out" method, meaning that the system automatically deletes the oldest photo. Language – Choose from English, German, Spanish, French, Russian, or Chinese NOTE: There is no way to export any of the photos on the device. language formats. Viewing and deleting messages: 1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display. 2. Highlight the "Messages" icon and press the "OK" button to enter the "Messages" screen. 3. Use the "Up" and "Down" buttons to select the message to be viewed. Setup – Set advanced settings such as Motion detection, Backlight time, Unlocking NOTE: Messages are the same as Automatic photos but are saved with the following format: duration, Pairing, Alarm settings, or Version information. "HH:MM:SS MM-DD-YYYY." 4. Press the "OK" button and select from "Open," "Delete," or "Delete All." a. Press "Open" to view a message. b. Press "Delete" to delete the selected message (after an additional prompt). c. Press "Delete All" to delete all messages (after an additional prompt). 5. Once viewing a message, press the "OK" button to return to the "Messages" screen. NOTE: The monitor can save up to 10 messages. Messages are saved in a "first-in, first-out" method, meaning that the system automatically deletes the oldest message. NOTE: Messages will not be saved if the indoor monitor is off. 8 SECO-LARM U.S.A., Inc. SECO-LARM U.S.A., Inc. 9


Document Created: 2018-07-25 13:58:21
Document Modified: 2018-07-25 13:58:21
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC