Test Report

FCC ID: JUP-5580090

Test Report

Download: PDF
FCCID_969592

FCC PART 15.247 INDUSTRY CANADA RSS-210, ISSUE 7, JUNE 2007 MEASUREMENT AND TEST REPORT For Trimble Navigation Limited 935 Stewart Drive Sunnyvale, CA 94085, USA FCC ID: JUP-5580090 IC: 1756A-5580090 This Report Concerns: Equipment Type: Supplemental Report GPS Receiver with 900MHz FHSS Transceiver Test Engineer: Xiao Ming Hu Report Number: R0805301-247 Report Date: 2008-06-03 Boni Baniqued Reviewed By: RF Sr. Engineer Bay Area Compliance Laboratories Corp. (BACL) 1274 Anvilwood Ave. Prepared By: Sunnyvale, CA 94089 (i0) Tel: (408) 732-9162 Fax: (408) 732-9164 www.baclcorp.com Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, NIST, or any agency of the Federal Government. * This report may contain data that are not covered by the NVLAP accreditation and are marked with an asterisk “*” (Rev.2)

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 TABLE OF CONTENTS 1 GENERAL INFORMATION ..............................................................................................................................4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)........................................................................4 1.2 MECHANICAL DESCRIPTION ............................................................................................................................4 1.3 EUT PHOTO ....................................................................................................................................................4 1.4 OBJECTIVE ......................................................................................................................................................5 1.5 RELATED SUBMITTAL(S)/ GRANT(S)...............................................................................................................5 1.6 TEST METHODOLOGY .....................................................................................................................................5 1.7 MEASUREMENT UNCERTAINTY .......................................................................................................................5 1.8 TEST FACILITY ................................................................................................................................................5 2 SYSTEM TEST CONFIGURATION .................................................................................................................7 2.1 JUSTIFICATION ................................................................................................................................................7 2.2 SPECIAL ACCESSORIES ....................................................................................................................................7 2.3 EQUIPMENT MODIFICATIONS ..........................................................................................................................7 2.4 POWER SUPPLY AND LINE FILTERS .................................................................................................................7 2.5 INTERNAL CONFIGURATION ............................................................................................................................7 2.6 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS ...........................................................................................7 2.7 INTERFACE PORTS AND CABLING....................................................................................................................7 2.8 TEST SETUP BLOCK DIAGRAM ........................................................................................................................8 3 SUMMARY OF TEST RESULTS FOR FCC PART 15C &IC RSS-210 ........................................................9 4 FCC §15.205, §15.209 & §15.247(C), IC RSS-210 §A8.5 - SPURIOUS RADIATED EMISSIONS ............10 4.1 APPLICABLE STANDARD ...............................................................................................................................10 4.2 TEST SETUP ..................................................................................................................................................11 4.3 TEST EQUIPMENT LIST AND DETAILS............................................................................................................12 4.4 ENVIRONMENTAL CONDITIONS .....................................................................................................................12 4.5 TEST PROCEDURE .........................................................................................................................................12 4.6 CORRECTED AMPLITUDE & MARGIN CALCULATION ....................................................................................12 4.7 SUMMARY OF TEST RESULTS ........................................................................................................................13 4.8 RADIATED SPURIOUS EMISSIONS TEST DATA ...............................................................................................13 5 EXHIBIT A – FCC & IC EQUIPMENT LABELING REQUIREMENTS...................................................15 5.1 FCC § 2.925 IDENTIFICATION OF EQUIPMENT .............................................................................................15 5.2 FCC ID LABELING REQUIREMENTS AS PER FCC § 15.19..............................................................................15 5.3 IC ID LABELING REQUIREMENTS AS PER RSS-GEN § 5.2 .............................................................................15 5.4 SUGGESTED FCC ID & IC LABEL .................................................................................................................16 6 EXHIBIT B TEST SETUP PHOTOS ...............................................................................................................17 6.1 RADIATED EMISSIONS – FRONT VIEW ...........................................................................................................17 6.2 RADIATED EMISSIONS – REAR VIEW ............................................................................................................17 7 EXHIBIT C - EUT PHOTOGRAPHS ..............................................................................................................18 7.1 EUT- TOP SIDE VIEW ....................................................................................................................................18 7.2 EUT- BOTTOM SIDE VIEW ............................................................................................................................18 7.3 EUT- FRONT SIDE VIEW ...............................................................................................................................19 7.4 EUT- REAR SIDE VIEW .................................................................................................................................19 7.5 EUT- MAIN BOARD A-TOP SIDE VIEW .........................................................................................................20 7.6 EUT- MAIN BOARD A -BOTTOM SIDE VIEW .................................................................................................20 Report #: R0805301-247 Page 2 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 7.7 EUT- DISPLAY BOARD ASSEMBLY VIEW ......................................................................................................21 7.8 EUT- TERMINAL BOARD ASSEMBLY VIEW ...................................................................................................21 7.9 EUT- 900MHZ RADIO BOARD WITH RF SHIELD-TOP SIDE VIEW .................................................................22 7.10 EUT- 900MHZ RADIO BOARD WITHOUT RF SHIELD-TOP SIDE VIEW ..........................................................22 7.11 EUT- 900MHZ RADIO BOARD -BOTTOM SIDE VIEW ....................................................................................23 7.12 EUT- GPS RECEIVER ANTENNA ...................................................................................................................23 7.13 EUT- 5 DBI ANTENNA ..................................................................................................................................24 7.14 EUT- AC/DC POWER SUPPLY-VIEW ............................................................................................................24 Report #: R0805301-247 Page 3 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 1 GENERAL INFORMATION 1.1 Product Description for Equipment under Test (EUT) The Trimble Navigation Limited Product, FCC ID: JUP-5580090, IC: 1756A-5580090, model: Wamel or the “EUT” as referred to this report is a triple-frequency GPS plus GLONASS receiver with the ability to receive OmniSTAR corrections. The SPS851 can operate as a base station or rover. The receiver can be configured using the keypad and display, web browser, or Trimble SCS900 Site Controller software. The SPS851 makes it easy to set up a mobile base station or a permanent base station for continuous operation. The SPS851 is also an ideal mobile receiver for semi-permanent mounting on vehicles and marine vessels. The SPS851 has an optional 900 MHz FHSS transceiver used to transmit or receive RTK (Real Time Kinematic) GPS data. The SPS851 also has an Infineon Bluetooth module PBA31308 for Bluetooth connectivity with other devices. The SPS751, SPS651 and SPS551 are less functional versions of the SPSx51 family, with fewer options than the SPS851. The AgGPS RTK Base 900, AgGPS 432 and AgGPS 442 are equivalent products aimed for the agricultural industry. All aforementioned models will be referred to in internal documentation as models: 58555-6X, 58555-90, and 58555-00. 1.2 Mechanical Description The EUT is a 900 MHz FHSS Radio Transceiver of metallic construction that measures approximately 226 mm (L) x 121 mm (W) x 57 mm (H) and weighs 1652 grams. * The test data gathered are from typical production sample, serial number: 4612K00874, provided by the manufacturer. 1.3 EUT Photo Please see additional photos in Exhibit C Report #: R0805301-247 Page 4 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 1.4 Objective This report is prepared on behalf of Trimble Navigation limited in accordance with Part 2, Subpart J, Part 15, Subparts A, B and C of the Federal Communication Commissions rules and Industry Canada RSS-210 Issue 7, June 2007 standard. The objective is to determine compliance with FCC and IC standards, rules and limits for this device including: • Radiated Spurious Emissions • Restricted Band 1.5 Related Submittal(s)/ Grant(s) The original non-RoHS 900MHz FHSS Radio was tested in Elliott Lab with FCC ID: JUP-5580090 and IC ID: 1756A-5580090. Additional testing was performed. Please refer to original report number R61810 which was prepared by Elliott Lab for other FCC 15.247 radio tests which include Channel Bandwidth, Channel Output Power, Channel Separation and Number of Channels. 1.6 Test Methodology All measurements contained in this report were conducted in accordance with ANSI C63.4-2003. 1.7 Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on NIS 81, The Treatment of Uncertainty in EMC Measurements, the values range from +2.0 dB for Conducted Emissions tests and +4.0 dB for Radiated Emissions tests are the most accurate estimates pertaining to uncertainty of EMC measurements at BACL. Detailed instrumentation measurement uncertainties can be found in BACL report QAP-018. 1.8 Test Facility The test site used by BACL Corp. to collect radiated and conducted emissions measurement data is located at its facility in Sunnyvale, California, USA. The test site at BACL Corp. has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports have been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11, 1997 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facility also complies with the test methods and procedures set forth in ANSI C63.4-2003 & TIA/EIA-603. Report #: R0805301-247 Page 5 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 The Federal Communications Commission and Voluntary Control Council for Interference have the reports on file and they are listed under FCC registration number: 90464 and VCCI Registration No.: R- 2463 and C-2698. The test site has been approved by the FCC and VCCI for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, BACL Corp. is a National Institute of Standards and Technology (NIST) accredited laboratory under the National Voluntary Laboratory Accredited Program (Lab Code 200167-0). The current scope of accreditations can be found at http://ts.nist.gov/ts/htdocs/210/214/scopes/2001670.htm. Report #: R0805301-247 Page 6 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 2 SYSTEM TEST CONFIGURATION 2.1 Justification The EUT was configured for testing according to ANSI C63.4-2003. The EUT was tested in the normal (native) operating mode to represent worst-case results during the final qualification test. 2.2 Special Accessories As shown in following test block diagram, all interface cables used for compliance testing are shielded. 2.3 Equipment Modifications N/A 2.4 Power Supply and Line Filters Manufacturer Description Model Serial Number AULT AC Adaptor (base) PW174KA1802F02 NA 2.5 Internal Configuration Manufacturer Description Part Number Rev Trimble Navigation Main Board A 55212-20-C 7 Trimble Navigation Display PCB Board PW-130-10K NA Trimble Navigation Main Board B 55212-C NA 2.6 Local Support Equipment List and Details Manufacturer Description Model Serial Number Dell Laptop Latitude D620 - Trimble Navigation 5 dBi Antenna - NA Trimble Navigation GPS Receiver Antenna ZEHYR model 2 - 2.7 Interface Ports and Cabling Cable Description Length (m) From To Serial Cable <3m EUT Laptop Report #: R0805301-247 Page 7 of 24 FCC Part15.247 & IC RSS-210 Test Report

Acecadsor <—T mani———> haaee ors recover arteoa sur Arteon Hectaningros C ies >

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 3 SUMMARY OF TEST RESULTS FOR FCC PART 15C &IC RSS-210 FCC 15C / RSS-210 Rules Description of Test Result FCC §15.247 (i) and §2.1091, IC RSS- Please refer to RF Exposure Gen 5.5 & RSS-102 Original Report* Please refer to FCC §15.203, IC RSS-Gen §7.1.4 Antenna Requirement Original Report* Please refer to FCC §15.207 (a), IC RSS-Gen §7.2.2 Conducted Emissions Original Report* FCC §2.1051 & §15.247(d), RSS210 § Please refer to Spurious Emissions at Antenna Port A8.5 § RSS-Gen §7.2 Original Report* FCC §15.205, §15.209 & §15.247(c), IC Radiated Spurious Emissions Compliant RSS-210 §A8.5 FCC §15.205, RSS-210 §A8.5 Restricted Band Compliant §15.109, 15.209 (a) & Please refer to Receiver Spurious Emissions §15.247(d), RSS-Gen §6(a) Original Report* Please refer to §15.247 (a)(1), RSS-210 §A8.1 (a) 20 dB Bandwidth & 99% Bandwidth Original Report* Please refer to §15.247 (a)(1), RSS-210 §A8.1(2) Hopping Channel Separation Original Report* Please refer to §15.247 (a)(1)(iii), RSS-210 §A8.1(4) Number of Hopping Frequencies Channel Used Original Report* Please refer to §15.247 (a)(1)(iii), RSS-210 §A8.1(4) Dwell Time Original Report* Please refer to §15.247 (b)(3), RSS210 § A8.4 Maximum Peak Output Power Original Report* Please refer to § 15.247 (d), RSS210 § A8.5 100 kHz Bandwidth of Frequency Band Edge Original Report* *Original submission FCC ID: JUP-5580090 filed 2006-03-13. *Original submission IC: 1756A-5580090 filed 2007-03-29. Report #: R0805301-247 Page 9 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 4 FCC §15.205, §15.209 & §15.247(c), IC RSS-210 §A8.5 - Spurious Radiated Emissions 4.1 Applicable Standard As per FCC §15.35(d): Unless otherwise specified, on any frequency or frequencies above 1000 MHz, the radiated emission limits are based on the use of measurement instrumentation employing an average detector function. Unless otherwise specified, measurements above 1000 MHz shall be performed using a minimum resolution bandwidth of 1 MHz. As per FCC §15.209(a): Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table Field Strength Measurement Frequency (micro Distance (MHz) volts/meter) (meters) 0.009 - 2400/F(kHz) 300 0.490 0.490 - 24000/F(kHz) 30 1.705 1.705 - 30 30 30.0 30 - 88 100** 3 88 - 216 150** 3 216 - 960 200** 3 Above 960 500 3 ** Except as provided in paragraph (g), fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72 MHz, 76-88 MHz, 174-216 MHz or 470-806 MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g., Sections 15.231 and 15.241. As per FCC §15.247(c)(1)(i): Systems operating in the 2400-2483.5 MHz band that are used exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain greater than 6 dBi provided the maximum conducted output power of the intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. Report #: R0805301-247 Page 10 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 As Per FCC §15.205(a) except as show in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: F (MHz) F (MHz) F (MHz) F (GHz) 0.090 – 0.110 16.42 – 16.423 960 – 1240 4. 5 – 5. 15 0.495 – 0.505 16.69475 – 16.69525 1300 – 1427 5. 35 – 5. 46 2.1735 – 2.1905 25.5 – 25.67 1435 – 1626.5 7.25 – 7.75 4.125 – 4.128 37.5 – 38.25 1645.5 – 1646.5 8.025 – 8.5 4.17725 – 4.17775 73 – 74.6 1660 – 1710 9.0 – 9.2 4.20725 – 4.20775 74.8 – 75.2 1718.8 – 1722.2 9.3 – 9.5 6.215 – 6.218 108 – 121.94 2200 – 2300 10.6 – 12.7 6.26775 – 6.26825 123 – 138 2310 – 2390 13.25 – 13.4 6.31175 – 6.31225 149.9 – 150.05 2483.5 – 2500 14.47 – 14.5 8.291 – 8.294 156.52475 – 156.52525 2690 – 2900 15.35 – 16.2 8.362 – 8.366 156.7 – 156.9 3260 – 3267 17.7 – 21.4 8.37625 – 8.38675 162.0125 –167.17 3.332 – 3.339 22.01 – 23.12 8.41425 – 8.41475 167.72 – 173.2 3 3458 – 3 358 23.6 – 24.0 12.29 – 12.293 240 – 285 3600 – 4400 31.2 – 31.8 12.51975 – 12.52025 322 – 335.4 36.43 – 36.5 12.57675 – 12.57725 399.9 – 410 Above 38.6 13.36 – 13.41 608 – 614 As per FCC §15.247 (d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a) (see §15.205(c)). IC RSS-GEN §4.9 the measurement method shall be described in the test report. The same parameter, peak power or average power, used for the transmitter output power measurement shall be used for unwanted emission measurements. The search for unwanted emissions shall be from the lowest frequency internally generated or used in the device (local oscillator, intermediate or carrier frequency), or from 30 MHz, whichever is the lower, to the 5th harmonic of the highest frequency generated without exceeding 40 GHz. 4.2 Test Setup The radiated emissions tests were performed in the shielded room, using the setup in accordance with ANSI C63.4-2003. The specification used was the FCC 15 Subpart C limits. Report #: R0805301-247 Page 11 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 4.3 Test Equipment List and Details Calibration Manufacturer Description Model Serial Number Date HP Pre amplifier 8447D 2944A07030 2007-11-12 Agilent Pre amplifier 8449B 3008A01978 2007-11-02 Sunol Science Combination Antenna JB1 Antenna A013105-3 2008-03-25 Antenna Research Horn Antenna DRG-118/A 1132 2007-06-18 Associates, Inc. ESCI 1166.595 Rohde & Schwarz EMI Test Receiver 1000337 2008-04-21 0K03 Sunol Science System Controller SC99V 122303-1 NR Agilent Spectrum analyzer E4440A MY44303352 2008-04-28 * Statement of Traceability: BACL Corp. attests that all calibrations have been performed per the NVLAP requirements, traceable to the NIST. 4.4 Environmental Conditions Temperature: 20° C Relative Humidity: 400 % ATM Pressure: 1012 mbar *The testing was performed by Xiao Ming Hu on 2008-05-30. 4.5 Test Procedure Maximizing procedure was performed on the six (6) highest emissions to ensure EUT compliance is with all installation combinations. All data were recorded in the peak detection mode. Quasi-peak readings was performed only when an emissions was found to be marginal (within -4 dB of specification limits), and are distinguished with a "QP" in the data table. 4.6 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corrected Amplitude = Indicated Reading + Antenna Factor + Cable Factor - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emissions are 7dB below the maximum limit. The equation for margin calculation is as follows: Margin = Corrected Amplitude - Limit Report #: R0805301-247 Page 12 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 4.7 Summary of Test Results According to the data hereinafter, the EUT complied with the FCC Title 47, Part 15 sections 15.205, 15.209 and Subpart C 15.247 standards’ limits, and had the margin from the limits of: Radiated spurious emissions above 1GHz -12.47 dB at 8704.518 MHz in the Vertical polarization, 1 GHz –10 GHz, Low Channel -14.6 dB at 8728.332 MHz in the Vertical polarization, 1 GHz – 10 GHz, Middle Channel -14.87 dB at 9795.072 MHz in the Horizontal polarization, 1 GHz – 10 GHz, High Channel 4.8 Radiated Spurious Emissions Test Data Low Channel @ 902.621MHz Antenna Cable Corrected Measurement Ant. Ant. Frequency Raw data Factor & Azt Limit Margin Loss Reading Type Polarity Height (MHz) (dBuV/m) Pre Amp (Deg) (dBuV/m) (dB) (dB) (dBuV/m) (PK/AV) (V/H) (cm) Gain (dB) 8704.518 28.00 11.17 2.36 41.53 AV V 198 49 54 -12.47 1804.894 61.13 4.94 -9.4 56.67 PK V 200 0 74 -17.33 8703.057 41.68 11.17 2.36 55.21 PK V 100 0 74 -18.79 1805.226 27.23 4.83 -10.43 21.63 AV V 169 263 54 -32.37 Middle Channel @ 914.8496MHz Antenna Cable Corrected Measurement Ant. Ant. Frequency Raw data Factor & Azt Limit Margin Loss Reading Type Polarity Height (MHz) (dBuV/m) Pre Amp (Deg) (dBuV/m) (dB) (dB) (dBuV/m) (PK/AV) (V/H) (cm) Gain (dB) 8728.438 25.85 11.19 2.35 39.4 AV V 171 45 54 -14.6 8728.322 41.38 11.19 2.35 54.92 PK V 200 0 74 -19.08 1892.701 50.56 4.94 -9.37 46.14 PK V 100 0 74 -27.86 1894.277 29.86 4.95 -9.35 25.46 AV V 98 209 54 -28.54 1995.367 26.7 5.07 -8.21 23.56 AV V 186 244 54 -30.44 1996.569 46.12 5.08 -8.2 42.99 PK V 100 0 74 -31.01 1447.6 28.34 4.32 -12.4 20.26 AV V 160 14 54 -33.74 1449.158 47.4 4.32 -12.4 39.33 PK V 100 0 74 -34.67 Report #: R0805301-247 Page 13 of 24 FCC Part15.247 & IC RSS-210 Test Report

Trimble Navigation Limited. FCC ID: JUP-5580090; IC: 1756A-5580090 High Channel @ 927.5877MHz Antenna Cable Corrected Measurement Ant. Ant. Frequency Raw data Factor & Azt Limit Margin Loss Reading Type Polarity Height (MHz) (dBuV/m) Pre Amp (Deg) (dBuV/m) (dB) (dB) (dBuV/m) (PK/AV) (V/H) (cm) Gain (dB) 9794.851 24.9 11.9 2.33 39.13 AV H 148 103 54 -14.87 9795.072 41.32 11.9 2.33 55.54 PK H 100 0 74 -18.46 1665.315 54.2 4.63 -11.52 47.31 PK H 100 0 74 -26.69 1666.731 31.81 4.63 -11.51 24.93 AV H 140 247 54 -29.07 Report #: R0805301-247 Page 14 of 24 FCC Part15.247 & IC RSS-210 Test Report


Document Created: 2008-07-11 17:10:12
Document Modified: 2008-07-11 17:10:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC