User Manual

FCC ID: JPZ0083

Users Manual

Download: PDF
FCCID_1555738

English StanzaTM FCC Information Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to StanzaTM Dimmers operate this equipment. SZ-6D, SZ-6ND NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant StanzaTM Switch to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may not cause harmful interfer- SZ-6ANS ence, and (2) this device must accept any interference received, including interference that may cause undesired Installation Instructions operation. Please Read Before Installing 120 V~ 50 / 60 Hz Important Notes Multigang Installations Install in accordance with all local and In multigang installations, several controls are grouped horizontally in one multigang national electrical codes. wallbox. Environment: Ambient operating When combining controls in a wallbox, derating is required. temperature: 32 to 104 °F (0 to 40 °C), 0 to 90% humidity, non-condensing. Derating Chart Control Location for Ganging Indoor use only. Dimmer and Switch Control Load Type End of Middle Spacing: If mounting one control above End of gang Dimmer with Neutral Gang of Gang another, leave at least 4.5 in (114 mm) vertical space between them. Incandescent 500 W 400 W Load Specifications SZ-6D, Faceplates: Use Lutron Stanza SZ-6ND 500 VA / 400 VA / MLV Control Load Type Min. Max. faceplates for best color match and 400 W 300 W Load Load aesthetic appearance. Do not paint SZ-5NE Incandescent 450 W 400 W Incandescent 40 W 600 W controls or faceplates. SZ-6NE 1 SZ-6NA ELV 450 W 400 W SZ-6D 2 600 VA / Cleaning: To clean, wipe with a clean MLV 40 W / VA Lighting 5A 3.5 A 450 W damp cloth. Do not use any chemical SZ- cleaning solutions. 6ANS Motor 3A 3A Middle of gang Incandescent 10 W 600 W SZ-6ND 1 Wallboxes: Lutron recommends using MLV2 600 VA / 10 W / VA 450 W 3.5 in (89 mm) deep wallboxes for easier installation. Several controls may Ensure your customer will 1 Installation SZ-5NE SZ-6NE Incandescent ELV 2 5W 5W 500 W 500 W be installed in one multigang wallbox — see Derating Chart. WARNING - Shock hazard STOP be happy by installing this product correctly so the SZ-6NA - Wiring with power ON may tapswitch protrudes from RF Device Placement: RF dimmers the faceplate. 3 Lighting 10 W / VA 6A and switches must be located within result in serious injury or death. SZ-6ANS Locate and remove fuse or lock Motor 0.083 A 3A 30 feet (9 m) of an RF signal repeater or 4. Push all wires back into the wallbox a device configured as a repeater. circuit breaker in the OFF position before and loosely fasten the control to the Notes proceeding. wallbox using the control mounting 1 Dimmer Load Type: SZ-6D and Stanza RF dimmers or switches cannot screws provided. Do not pinch the be controlled by the system until they Short Circuit Check: Check the SZ-6ND are designed for use with installation for short circuits before wires. permanently installed incandescent, are addressed and programmed. They will work as stand-alone controls only. installing control(s). With power OFF, • For installation with a recessed magnetic low-voltage (MLV), or install standard mechanical switch(es) or wallbox, use spacer shims (Lutron tungsten halogen only. SZ-5NE is wire connector(s) between hot and load. PN 257117) for proper support of designed for permanently installed Restore power. If lights do not work or a control(s). incandescent, electronic low-voltage breaker trips, correct wiring and check • For multigang installation, verify (ELV), or tungsten halogen only. again. Install control(s) only when short that the order of controls in the Dimmers cannot control motor- is no longer present. Warranty is void wallbox corresponds to the faceplate operated equipment. Dimmers and if control is turned ON with a shorted openings. switches cannot control standard FCC Information circuit. receptacles. Contact Lutron for 5. A  ttach Lutron Stanza faceplate Note: This equipment has been tested and found to dimmable receptacle solution. adapter and faceplate. comply with the limits for a Class B digital device, 1. T urn power OFF at fusebox or circuit 2 Low-Voltage Applications: Use pursuant to Part 15 of the FCC rules. These limits are breaker. a. Align the locating posts on the SZ-6D and SZ-6ND with magnetic (core designed to provide reasonable protection against control(s) to the holes in the and coil) low-voltage transformers only. harmful interference in a residential and commercial 2. Prepare wires. When making wire adapter. Not for use with electronic (solid-state) installation. This equipment generates, uses and can connections, trim or strip wallbox wires to the length indicated by the b. Install the adapter onto front of low-voltage transformers. radiate radio frequency energy and, if not installed and control(s) using the short screws used in accordance with the instructions, may cause strip gauge on the back of the control. Use SZ-5NE with electronic (solid- provided. The faceplate adapter harmful interference to radio or television reception. Note: Wire connectors provided are state) low-voltage transformers only. should be firmly against the However, there is no guarantee that interference will suitable for copper wire only. Not for use with magnetic (core and control. coil) low-voltage transformers). not occur in a particular installation. If this equipment Wire Connector: does cause harmful interference to radio or television • Use to join one 14 AWG (1.5 mm2) c. Tighten control mounting screws Operation of a low-voltage circuit until faceplate adapter is flush to reception, which can be determined by turning the or 12 AWG (2.5 mm2) ground wire with lamps inoperative or removed wall (do not over-tighten). equipment off and on, the user is encouraged to try to with one 18 AWG (0.75 mm2) control may result in transformer overheating correct the interference by one or more of the ground wire. d. Snap faceplate onto faceplate and premature failure. Lutron strongly recommends the following: following measures: Twist wire connector tight. adapter, and verify that control is • Do not operate low-voltage circuits • R eorient or relocate the receiving antenna. Push-In Terminals: aligned properly and switch(es) without operative lamps in place. • Increase the separation between the equipment and Insert wires fully. Push-in protrude(s) in front of the faceplate. receiver. terminals are for use with e. If control(s) is (are) misaligned or • Replace burned-out lamps as quickly • C onnect the equipment into an outlet on a circuit as possible. 14 AWG (1.5 mm2) solid switch(es) is (are) flush with the different from that to which the receiver is copper wire only. DO NOT faceplate, loosen control mounting • Use transformers that incorporate connected. thermal protection or fused use stranded or twisted wire. screws appropriately. • C onsult the dealer or an experienced radio/TV OR transformer primary windings to technician for help. 6. Restore power. Check for correct prevent transformer failure due to Screw Terminals: local operation (see Dimmer overcurrent. Tighten securely to Operation and Switch Operation). 5 in•lbs (0.55 N•m). 3 Switch Load Type: SZ-6ANS is Screw terminals are for use designed for use with all permanently with solid copper wire only. installed lighting loads and with motor DO NOT use stranded or loads up to 1/4 HP (3 A). twisted wire. Mounting Diagram Control Faceplate adapter 3. Wire controls as follows: mounting screws mounting screws Single location installation: See Locating post Wiring Diagrams 1 and 2. Power Booster and Interfaces: When using power boosters or interfaces, see wiring diagrams provided with the interface. Locating hole Faceplate/adapter purchased separately. Correct: Incorrect: Dimmer/switch protrudes Dimmer/switch is flush Locating post from faceplate. with faceplate. Loosen control mounting screws. Control Locating hole

Wiring Diagram 1 Single Location Installation Troubleshooting Guide SZ-6D Dimmer Symptom Cause and Action Brass Load is off and there Power not present is no indicator on the • Circuit breaker OFF or tripped. Perform short circuit check. dimmer/switch • FASS is in the OFF position. Move FASS to the ON position by Hot/Live Black fully pushing it up. Green Lighting 120 V~ Wiring error load 50 / 60 Hz • Check wiring to be sure it matches installation instructions Ground and wiring diagrams. Neutral Lamps burned out or not installed (SZ-6D only) • Replace or install lamps. Wiring Diagram 2 Single Location Installation with Neutral Dioded lamps SZ-6ND, SZ-5NE, SZ-6ANS • Replace with non-dioded lamps. Dimmer/Switch Damaged dimmer/switch Brass • Device may have been damaged by previous overload or Silver miswire. Replace device. Hot/Live Black Dimmer / switch indica- Wiring error tor is on but load can- • Check wiring to be sure it agrees with installation instructions Green 120 V~ Load not be turned on and/or and wiring diagrams. 50 / 60 Hz cannot be turned off Ground Lamps burned out or not installed (SZ-6ND, SZ-6ANS) Neutral • Replace or install lamps. Damaged dimmer/switch • Device may have been damaged by previous overload or miswire. Replace device. Dimmer Operation (SZ-6D, SZ-6ND, SZ-5NE) Light turns ON and OFF Load is less than minimum load requirement continuously • Make sure the connected load meets the minimum load requirement for that control. See Load Specifications table. Dimming Slider Slide up to brighten; slide down to dim Improper load type Load must be on for slider to affect intensity • Check that the load being dimmed is dimmable. See Load Specifications table. Indicator light in slider track Glows softly green for easy locating of control Lights don’t switch ON/ Improper programming Track ends flash amber to indicate programming/ OFF from keypad • Check programming in the Stanza software. addressing mode Out of RF range Tapswitch • Ensure device is within 30 feet (9 m) of another device Turns load on to slider level and off configured as a repeater. FASSTM Wiring Front-accessible service switch (facilitates safe bulb • Wiring error. Check wiring to be sure it agrees with installa- replacement) Pull down to remove all electrical power from load tion instructions and wiring diagrams. and deactivate dimmer Faceplate is warm Solid-state control dissipation Push up to restore power to load and dimmer • Solid-state dimmers and switches internally dissipate about 2% of the total connected load. It is normal for dimmers and Switch Operation (SZ-6ANS) switches to feel warm to the touch during operation. Control is buzzing or It is normal for dimmers and switches to emit a slight buzzing or humming humming sound. Indicator light Glows softly green for easy locating of control Ends flash amber to indicate programming/ addressing mode Tapswitch Turns load on and off FASSTM Front-accessible service switch (facilitates safe bulb replacement) Pull down to remove all electrical power from load and deactivate switch Push up to restore power to load and switch Lamp Replacement  ARNING - Shock hazard - Working with power ON may result in serious W injury or death. For any procedure other than routine lamp replacement, disconnect power at the main electrical panel. Technical support: U  SA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 For routine lamp replacement, remove power from the fixture(s) by pulling down Central/South America: +1.610.282.6701 the FASS switch on the Dimmer / Switch. Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with 8-year pro-rated parts replacement on systems that include factory startup. Lutron and the sunburst logo are registered trademarks and FASS and Stanza are trademarks of Lutron Electronics Co., Inc. © 2011 Lutron Electronics Co., Inc. Lutron Electronics Co., Inc. Made and print­ed in the U.S.A. ® P/N 030-1603 Rev. A 07/2011


Document Created: 2011-07-28 16:03:47
Document Modified: 2011-07-28 16:03:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC