User Manual

FCC ID: JPZ0070

Users Manual

Download: PDF
FCCID_1279251

StanzaTM FCC Information Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this SZ-CI-USB-CPN5138 equipment. NOTE: This equipment has been tested and found to comply with USB Interface the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Operation is subject to the following: (1) This device may Installation Instructions PELV (Class 2: USA) Device not cause harmul interference, and (2) this device must accept any interference received, including interference that may cause Occupant Copy Please Read 5V 60 mA undesired operation. Features Mounting • Integrates a Stanza guest room lighting control system 1. Secure the provided mounting clip to a flat, clean with a PC or other digital equipment that supports USB surface with the double-sided tape on the clip. devices. Then secure the USB interface in the mounting • Provides a basic serial string command set that allows a clip. PC to monitor and control lighting. 2. Connect the provided USB cable from the device • Programmed and commissioned by a SZ-CI-PRG to the 3rd party equipment. Programming Control Interface. 3. Use provided antenna clip and double-sided tape • Should not be used in “Advanced” systems with a to securely mount the antenna. permanently installed SZ-CI-PRG. 4. Mount in an accessible location for convenient • Wireless connection allows easy mounting near access to the programming button, LED, and USB integration device. cable. 5. The unit cannot be mounted in a full metal enclosure or between two metal surfaces. 6. When mounting, provide sufficient space for the antenna and USB cable. Dimensions Dimensions are in inches. 4.0 Antenna Clip 0.5 0.89 0.843 1.691 0.78 USB Mini-B Female Connector 0.44 0.255 Mounting Clip 31.5 FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment. Operation is subject to the following: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. R

Device Operation USB Mini-B Female Connector Button Used during device programming for association to Stanza system. LED Off during normal operation (unless TX / RX monitoring is enabled). Flashes Orange during programming mode. Mounting Clip Troubleshooting Symptom Cause and Action Device does not address to system. Device not powered • Connecting equipment is not powered • USB port on connecting equipment not powered Device out of RF range • Ensure device is within 30 ft (9 m) of StanzaTM device configured as a repeater Device is programmed to another system • Contact Lutron Technical Support for details on how to factory default the device COM port cannot be established with Device not powered device • Connecting equipment is not powered • USB port on connecting equipment not powered Virtual COM port is set up incorrectly • See the Lutron Integration Protocol guide for proper COM port settings Device does not respond to integration Virtual COM port is set up incorrectly commands • See the Lutron Integration Protocol guide for proper COM port settings Device is not programmed to system • Ensure device was addressed to an existing Stanza system Incorrect integration commands • Ensure that the proper commands and integration IDs are being used StanzaTM system devices do not respond Device out of RF range to issued integration commands • Ensure device is within 30 ft (9 m) of Stanza device configured as a repeater Incorrect integration commands • Ensure that the proper commands and integration IDs are being used Device does not monitor system changes Virtual COM port is set up incorrectly • See the Lutron Integration Protocol guide for proper COM port settings Device is not programmed to system • Ensure device was addressed to an existing Stanza system Device out of RF range • Ensure device is within 30 ft (9 m) of Stanza device configured as a repeater Monitoring disabled • See the Lutron Integration Protocol guide for disabling/enabling monitoring Internet: www.lutron.com/stanza e-mail: product@lutron.com Technical support: USA, Canada, Caribbean: 1.800.523.9466 Mexico: +1.888.235.2910 Central/South America: +1.610.282.6701 Warranty: 1-year limited warranty standard. 2-year parts and labor warranty, with 8-year pro-rated parts Lutron Electronics Co., Inc. replacement on systems that include factory startup. Made and printed in U.S.A. P/N 040-361 Rev. A 04.21.10 For complete warranty details, see the Start-Up/Warranty document provided with your Stanza system specification submittal information. Lutron and the sunburst logo are registered trademarks and Stanza is a trademark of Lutron Electronics Co., Inc. © 2010 Lutron Electronics Co., Inc. R


Document Created: 2010-04-21 18:09:05
Document Modified: 2010-04-21 18:09:05
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC