User Manual

FCC ID: JLFPIR2

Users Manual

Download: PDF
FCCID_932242

® Model PIRV400R Wireless Pedestrian & Vehicle Sensor with Voice Overview Intercom Feature: When PIR Motion Sensor has The PIR Motion Sensor only works with detected motion, the Base Station will allow you to Chamberlain's Wireless Pedestrian & Vehicle Alert listen through the PIR Motion Sensor for 10 seconds. with Voice (Model RWV400R). The PIR Motion If you wish to talk to the person on the other end, Sensor can be used to monitor motion up to 30' away hold down the Talk button and speak, releasing it to and can transmit a signal up to 1000' away from the hear. Base Station (not included). The Passive Infra-Red sensor detects movement of people and vehicles, Volume: Pressing the Volume button repeatedly will while allowing small animals to pass through cycle through volume levels. undetected. The PIR Motion Sensor has a built-in microphone and speaker that allows for Mute: To temporarily mute Base Station, hold the communication between the Base Station and the Volume and Talk buttons down for three seconds. The Sensor. When the PIR Motion Sensor detects Base Station will reactivate after one hour, or by movement a signal is sent to the base station which pressing the Talk button. alerts the homeowner with sounds and lights. The Alert can also remotely control an electrical device Remote Button: If there is an accessory device near the PIR Motion Sensor like a light or a connected to the relay on the PIR Motion Sensor, it camera (See Advanced Features). can be activated by pressing the Remote button within 30 seconds of the signal from the alert buzzer. Carton Inventory Switch #1: OFF Buzzer Off ON Buzzer On (Default) Swivel Bushing OFF Switch #2: 1 2 ON OFF Long Buzz ON Short Buzz (Default) Mounting Plate Battery: The AA Alkaline batteries (not provided) will Passive Infra-Red (PIR) last up to 2 years depending on use (Lithium batteries Motion Sensor recommended for colder environments). If PIR Motion Sensor batteries are low Base Station will emit three high-pitch beeps every ten minutes. If Base Station batteries are low it will emit two high-pitch beeps. Operation & Features Clear Memory: Press and hold the Learn button on PIR Motion Base Station the Base Station until 3 beeps are heard. If PIR Motion Sensor signals while Learn button is pressed, Sensor (not provided) repeat the procedure. PIR Sensor/Test Light Volume Button Talk (Power - On) Programming Additional PIR Motion Sensors: Each Base Station can learn the code of up to 8 PIR Motion Sensors, responding with multiple buzzes. To program additional PIR Motion Sensors see Step 6. Remote Relay Output Activation Contacts Button AC Adapter Learn Switch #1: Mute Button Speaker Switch #2: Tone On/Off: To turn Base Station OFF hold down the Volume button until a beep is heard and light goes out. To turn Base Station ON press the Talk button. 1

PIR Motion Sensor Assembly & Programming PIR Motion Test Sensor to Base Station Step 1 Step 6 A Ensure that Base Connect PIR Motion A Station and PIR Sensor box to Motion Sensor are in mounting plate with close proximity to silver screw. Tighten each other. Press and screw until PIR Motion release learn button Sensor stays in place on Base Station. when repositioned. Buzzer will sound. Step 2 A B A Install 4 AA Alkaline B batteries (not provided). (Lithium batteries recommended for colder environments.) B Ensure batteries do not touch circuit B Within 5 seconds, wave hand in front of PIR Motion board. Sensor. Test light will illuminate and Base Station Step 3 will activate with static and feedback after several seconds. Test PIR Motion Sensor by waving hand in front of PIR Motion Sensor Installation sensor. Test light Step 7 should flash after several seconds. Mount PIR Motion Sensor vertically on solid surface a few feet off the ground and Step 4 within 1000' of Base Station. Unit should be Secure cover with the able to swivel as two large black needed. screws. NOTE: Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. Vehicle Alert Installation: For cars, the best Step 5 mounting position is about 4' high, between 10-20' back, and angled to see the back of car after passing the sensor. 10' - 20' OPTIONAL 3' - 5' Ensure Base Station (not provided) has power. 2

Advanced Features Troubleshooting Both the PIR Motion Sensor and Base Station have The Alert does not function. relays which can activate other electrical devices. The Check batteries in PIR Motion Sensor. Ensure Base relay switches can handle up to 120 AC volts at 10 Station has power. Ensure PIR Motion Sensor is amps. The accessory device will need a separate programmed to Base Station. power supply. The Alert is not getting expected transmission Base Station: The relays can be range. used to activate louder alarm bells, Ensure Base Station antenna is vertical and keep PIR lights, cameras, or other accessories. Motion Sensor away from trees and metal objects. Ensure Base Station is in clearest possible range of PIR Motion Sensor: The relays will PIR Motion Sensor. The less objects between only activate when the remote button devices, the longer the range. is pressed on the Base Station. To prevent access to these relays flush Base Station is not very loud. mount the PIR Motion Sensor. Adjust the volume of speaker. An accessory such as a bell, buzzer or light can be attached to the relay switch. The relay switch can handle up to 120 AC volts at 10 amps. The accessory device will need separate power supply. Static and feedback is heard in Base Station. PIR Motion Sensor is too close to the Base Station. The PIR Motion Sensor is detecting motion only part of the time. To detect cars, it is best to mount PIR Motion Sensor at height of car’s motor and have it between ten and twenty feet from the road. Swivel sensor as needed. The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR sensor can also be triggered by light shining directly in sensor window, such as reflected sunlight, or motion in front of a light source. Base Station beeps every ten minutes. If there are two beeps the battery is low in the Base Station. Replace with AA Alkaline batteries or operate it with AC Adapter. If there are three beeps the battery is low in the PIR Motion Sensor. Replace with AA Alkaline batteries. 3

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www.chamberlain-DIY.com NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. © 2007, The Chamberlain Group Inc. 114A3516 All Rights Reserved


Document Created: 2007-12-13 11:25:10
Document Modified: 2007-12-13 11:25:10
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC