TEST REPORT

FCC ID: JLFPIR2

Test Report

Download: PDF
FCCID_469370

FCCID: JLFPIR2 Date: September 8, 2004 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: International Electronics Inc Equipment: The Reporter Voice FCC ID: JLFPIR2 FCC Rules: 2, 15.249 Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. Filing fees are attached. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Michael Schafer, Business Director enclosure(s) cc: Applicant MS/del MFA p0480015, d0490022

FCCID: JLFPIR2 List Of Exhibits (FCC Certification (Transmitters) - Revised 9/28/98) Applicant: International Electronics Inc FCC ID: JLFPIR2 By Applicant: 1. Letter Of Authorization 2. Identification Drawings Label Location of Label Compliance Statement Location of Compliance Statement 3. Documentation: 2.1033(B) (3) User Manual (4) Operational Description (5) Block Diagram (5) Schematic Diagram (7) Photographs Block Diagram Parts List Active Devices 4. Draft Specification Information By M.F.A. Inc. A. Testimonial & Statement of Certification MFA p0480015, d0490022

FCCID: JLFPIR2 Transmitter Certification of Model: The Reporter Voice FCCID: JLFPIR2 to Federal Communications Commission Rule Part(s) 2. 15.249 Date Of Report: September 8, 2004 On the Behalf of the Applicant: International Electronics, Inc. At the Request of: P.O.12422 International Electronics, Inc. 5913-C NE 127th Avenue, Suite#800 Vancouver, WA 98682, USA Attention of: Shary Nissimi Supervised By: David E. Lee, Compliance Test Manager MFA p0480015, d0490022

FCCID: JLFPIR2 The Applicant has been cautioned as to the following: 15.21 Information to User. The users manual or instruction manual for an intentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 15.27(a) Special Accessories. Equipment marketed to a consumer must be capable of complying with the necessary regulations in the configuration in which the equipment is marketed. Where special accessories, such as shielded cables and/or special connectors are required to enable an unintentional or intentional radiator to comply with the emission limits in this part, the equipment must be marketed with, i.e. shipped and sold with, those special accessories. However, in lieu of shipping or packaging the special accessories with the unintentional or intentional radiator, the responsible party may employ other methods of ensuring that the special accessories are provided to the consumer, without additional charge. Information detailing any alternative method used to supply the special accessories for a grant of equipment authorization or retained in the verification records, as appropriate. The party responsible for the equipment, as detailed in § 2.909 of this chapter, shall ensure that these special accessories are provided with the equipment. The instruction manual for such devices shall include appropriate instructions on the first page of text concerned with the installation of the device that these special accessories must be used with the device. It is the responsibility of the user to use the needed special accessories supplied with the equipment. MFA p0480015, d0490022

FCCID: JLFPIR2 Table Of Contents Rule Description Page . Test Report 1 2.1033(c) General Information Required 2 . Standard Test Conditions and Engineering Practices 6 2.1053(a) Field Strength of Spurious Radiation 7 15.249(a). Maximum Radiated Field Strength 12 15.249(c). Radiated Spurious Emissions (Non-Harmonic) 14 2.1049(c)(1) Emission Masks (Occupied Bandwidth) 15 MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 1 of 18. Required information per ISO/IEC Guide 25-1990, paragraph 13.2: a) Test Report b) Laboratory: M. Flom Associates, Inc. (FCC: 31040/SIT) 3356 N. San Marcos Place, Suite 107 (Canada: IC 2044) Chandler, AZ 85225 c) Report Number: d0490022 d) Client: International Electronics Inc e) Identification: The Reporter Voice System Description: Passive Infra Red Sensor 2 f) EUT Condition: Not required unless specified in individual tests. g) Report Date: August 27, 2004 EUT Received: July 30, 2004 h, j, k): As indicated in individual tests. i) Sampling method: No sampling procedure used. l) Uncertainty: In accordance with MFA internal quality manual. m) Supervised by: David E. Lee, Compliance Test Manager n) Results: The results presented in this report relate only to the item tested. o) Reproduction: This report must not be reproduced, except in full, without written permission from this laboratory. MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 2 of 18. List Of General Information Required For Certification In Accordance with FCC Rules and Regulations, Volume II, Part 2 and to 15.249 Sub-Part 2.1033 (c)(1): Name and Address of Applicant: International Electronics, Inc. 5913-C NE 127th Avenue, Suite#800 Vancouver, WA 98682, USA Manufacturer: Applicant (c)(2): FCC ID: JLFPIR2 Model Number: Passive Infra Red Sensor 2 (c)(3): Instruction Manual(s): Please See Attached Exhibits (c)(4): Type of Emission: ASK (c)(5): FREQUENCY RANGE, MHz: 916.500 (c)(6): Power Rating,: 29.915 mV/m @3m Switchable Variable X N/A (c)(7): Maximum Power Rating,: 50 mV/m @ 3m 15.203: Antenna Requirement: X The antenna is permanently attached to the EUT The antenna uses a unique coupling The EUT must be professionally installed The antenna requirement does not apply MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 3 of 18. Subpart 2.1033 (continued) (c)(8): Voltages & Currents in All Elements in Final RF Stage, Including Final Transistor or Solid State Device: Collector Current, A = 0.012 Collector Voltage, Vdc = 3.7 Supply Voltage, Vdc = 6 (c)(9): Tune-Up Procedure: Please See Attached Exhibits (c)(10): Circuit Diagram/Circuit Description: Including description of circuitry & devices provided for determining and stabilizing frequency, for suppression of spurious radiation, for limiting modulation and limiting power. Please See Attached Exhibits (c)(11): Label Information: Please See Attached Exhibits (c)(12): Photographs: Please See Attached Exhibits (c)(13): Digital Modulation Description: ___ Attached Exhibits _x_ N/A (c)(14): Test and Measurement Data: Follows MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 4 of 18. A2LA “A2LA has accredited M. Flom Associates, Inc. Chandler, AZ for technical competence in the field of Electrical Testing. The accreditation covers the specific tests and types of tests listed on the agreed scope of accreditation. This laboratory meets the requirements of ISO/IEC 17025 – 1999 ‘General Requirements for the Competence of Testing and Calibration Laboratories’ and any additional program requirements in the identified field of testing.” Certificate Number: 2152-01 NIST I am pleased to inform you that your laboratory has been validated by the Chinese Taipei Bureau of Standards, Metrology and Inspection (BSMI) under the Asia Pacific Economic Cooperation Mutual Recognition Agreement (APEC MRA). Your laboratory is now formally designated to act as a Conformity Assessment Body (CAB) under Appendix B, Phase I Procedures, of the APEC MRA between the American Institute in Taiwan (AIT) and the Taipei Economic and Cultural Representative Office (TECRO) in the United States, covering equipment subject to Electro- Magnetic Compatibility (EMC) requirements. The names of all validated and nominated laboratories will be posted on the NIST website at http://ts.nist.gov/mra under the ‘Asia’ category.” MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 5 of 18. Sub-part 2.1033(b): Test and Measurement Data All tests and measurement data shown were performed in accordance with FCC Rules and Regulations, Volume II; Part 2, Sub-part J, Sections 2.1031, 2.1033, 2.1035, 2.1041, 2.1043, 2.1045, and the following individual Parts: 15.209 Radiated emission limits; general requirements 15.211 Tunnel radio systems 15.213 Cable locating equipment 15.214 Cordless telephones 15.217 Operation in the band 160-190 kHz 15.219 Operation in the band 510-1705 kHz 15.221 Operation in the band 525-1705 kHz (leaky coax) 15.223 Operation in the band 1.705-10 MHz 15.225 Operation in the band 13.553-13.567 MHz 15.227 Operation in the band 26-27.28 MHz (remote control) 15.229 Operation in the band 40.66-40.70 MHz 15.231 Periodic operation in the band 40.66-40.70 MHz and above 70 MHz 15.233 Operation within the bands 43.71-44.49, 46.60-46.98 MHz 48.75-49.51 MHz and 49.66-50.0 MHz 15.235 Operation within the band 49.82-49.90 MHz 15.237 Operation within the bands 72.0-73.0 MHz, 74.6-74.8 MHz and 75.2-76.0 MHz (auditory assistance) 15.239 Operation in band 88-108 MHz 15.241 Operation in the band 174-216 MHz (biomedical) 15.243 Operation in the band 890-940 MHz (materials) 15.245 Operation within the bands 902-928 MHz, 2435-2465 MHz, 5785-5815 MHz, 10500-10550 MHz, and 24075-24175 MHz (filed disturbance sensors) 15.247 Operation within bands 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz (spread spectrum) X 15.249 Operation within the bands 902-928 MHz, 2400-2483.5 MHz, 5725-5875 MHz, and 24.0-24.25 GHz 15.251 Operation within the bands 2.9-3.26 GHz, 3.267-3.332 GHz, 3.339-3.3458 GHz, and 3.358-3.6 GHz (vehicle identification systems) 15.321 Specific requirements for asynchronous devices operating in the 1910-1920 MHz and 2390-2400 MHz bands (Unlicensed PCS) 15.323 Specific requirements for isochronous devices operating in the 1920-1930 MHz sub-band (Unlicensed PCS) MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 6 of 18. Standard Test Conditions And Engineering Practices Except as noted herein, the following conditions and procedures were observed during the testing: In accordance with ANSIC63.4-1992/2001, section 6.1.9, and unless otherwise indicated in the specific measurement results, the ambient temperature of the actual EUT was maintained within the range of 10° to 40°C (50° to 104 °F) unless the particular equipment requirements specify testing over a different temperature range. Also, unless otherwise indicated, the humidity levels were in the range of 10% to 90% relative humidity. Prior to testing, the EUT was tuned up in accordance with the manufacturer's alignment procedures. All external gain controls were maintained at the position of maximum and/or optimum gain throughout the testing. Measurement results, unless otherwise noted, are worst-case measurements. MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 7 of 18. Name of Test: Field Strength of Spurious Radiation Specification: 47 CFR 2.1053(a) Guide: ANSI/TIA/EIA-603-1992/2001, Paragraph 1.2.12 and Table 16, 47 CFR 22.917 Measurement Procedure 1.2.12.1 Definition: Radiated spurious emissions are emissions from the equipment when transmitting into a non-radiating load on a frequency or frequencies which are outside an occupied band sufficient to ensure transmission of information of required quality for the class of communications desired. 1.2.12.2 Method of Measurement A) Connect the equipment as illustrated B) Adjust the spectrum analyzer for the following settings: 1) Resolution Bandwidth 100 kHz (<1 GHZ), 1 MHZ (> 1GHz). 2) Video Bandwidth ≥ 3 times Resolution Bandwidth, or 30 kHz (22.917) 3) Sweep Speed ≤2000 Hz/second 4) Detector Mode = Mean or Average Power C) Place the transmitter to be tested on the turntable in the standard test site. The transmitter is transmitting into a non-radiating load which is placed on the turntable. The RF cable to this load should be of minimum length. MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 8 of 18. Name of Test: Field Strength of Spurious Radiation (Cont.) D) For each spurious measurement the test antenna should be adjusted to the correct length for the frequency involved. This length may be determined from a calibration ruler supplied with the equipment. Measurements shall be made from the lowest radio frequency generated in the equipment to the tenth harmonic of the carrier, except for the region close to the carrier equal to ± the test bandwidth (see section 1.3.4.4). E) For each spurious frequency, raise and lower the test antenna from 1 m to 4 m to obtain a maximum reading on the spectrum analyzer with the test antenna at horizontal polarity. Repeat this procedure to obtain the highest possible reading. Record this maximum reading. F) Repeat step E) for each spurious frequency with the test antenna polarized vertically. G) Reconnect the equipment as illustrated. H) Keep the spectrum analyzer adjusted as in step B). I) Remove the transmitter and replace it with a substitution antenna (the antenna should be half-wavelength for each frequency involved). The center of the substitution antenna should be approximately at the same location as the center of the transmitter. At lower frequencies, where the substitution antenna is very long, this will be impossible to achieve when the antenna is polarized vertically. In such case the lower end of the antenna should be 0.3 m above the ground. MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 9 of 18. Name of Test: Field Strength of Spurious Radiation (Cont.) J) Feed the substitution antenna at the transmitter end with a signal generator connected to the antenna by means of a non-radiating cable. With the antennas at both ends horizontally polarized and with the signal generator tuned to a particular spurious frequency, raise and lower the test antenna to obtain a maximum reading at the spectrum analyzer. Adjust the level of the signal generator output until the previously recorded maximum reading for this set of conditions is obtained. This should be done carefully repeating the adjustment of the test antenna and generator output. K) Repeat step J) with both antennas vertically polarized for each spurious frequency. L) Calculate power in dBm into a reference ideal half-wave dipole antenna by reducing the readings obtained in steps J) and K) by the power loss in the cable between the generator and the antenna and further corrected for the gain of the substitution antenna used relative to an ideal half-wave dipole antenna. M) The levels recorded in step L) are absolute levels of radiated spurious emissions in dBm. The radiated spurious emissions in dB can be calculated by the following: Radiated spurious emissions dB = 10log10(TX power in watts/0.001) – the levels in step l) NOTE: It is permissible that other antennas provided can be referenced to a dipole. Test Equipment: Asset Description s/n Cycle Last Cal Per ANSI C63.4-1992/2000 Draft, 10.1.4 (as applicable) Transducer i00088 EMCO 3109-B 25MHz-300MHz 2336 24 mo. Sep-03 i00065 EMCO 3301-B Active Monopole 2635 24 mo. Sep-03 X i00089 Aprel 2001 200MHz-1GHz 001500 24 mo. Sep-03 X i00103 EMCO 3115 1GHz-18GHz 9208-3925 24 mo. Sep-03 Amplifier X i00028 HP 8449A 2749A00121 12 mo. Mar-04 Spectrum Analyzer i00029 HP 8563E 3213A00104 12 mo. Mar-04 X i00033 HP 85462A 3625A00357 12 mo. Sep-03 MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 10 of 18. Test Setup: Radiated Emissions State: MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 11 of 18. Name of Test: Field Strength of Spurious Radiation g0480110: 2004-Aug-20 Fri 15:36:00 State: 2:High Power Frequency Tuned, Frequency Emission, Meter, dBuV CF, dB uV/m @ 3m MHz MHz 916.500000 1833.254000 12.94 43.05 350.13 916.500000 2749.838000 12.93 44.18 365.54 916.500000 3666.396667 29.00 12.7 121.62 916.500000 4582.996667 31.17 15.17 207.49 916.500000 5499.596667 29.17 15.26 166.53 916.500000 6416.196667 28.50 16.55 178.85 916.500000 7332.796667 31.17 17.87 283.14 916.500000 8249.396667 32.17 20.65 437.52 916.500000 9165.996667 29.33 18.59 248.89 MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 12 of 18. Name of Test: Maximum Radiated Field Strength Specification: 47 CFR 15.249(a) Spec. Limit: 50 mV/m @ 3m Radiated Test Setup NOTES: (a) Search Antenna - Rotatable on boom (j) Cables routed through hollow turntable (b) Non-metallic boom center (c) Non-metallic mast (k) 30 cm or less (d) Adjustable horizontally (l) External power source (e) Equipment Under Test (m) 10 cm diameter coil of excess cable (f) Turntable (n) 25 cm (V), 1 m-7 m (V, H) (g) Boom adjustable in height. (o) 25 cm from bottom end of 'V', 1m (h) External control cables routed normally horizontally at least one wavelength. (p) Calibrated Cable at least 10m in length (i) Rotatable (q) Amplifier (optional) (r) Spectrum Analyzer Asset Description s/n Cycle Last Cal (as applicable) Per ANSI C63.4-1992, 10.1.4 Transducer X i00088 EMCO 3109-B 25MHz-300MHz 2336 24 mo. Sep-03 X i00089 Aprel 2001 200MHz-1GHz 001500 24 mo. Sep-03 X i00103 EMCO 3115 1GHz-18GHz 9208-3925 24 mo. Sep-03 Amplifier X i00028 HP 8449A 2749A00121 12 mo. Mar-04 Spectrum Analyzer X i00029 HP 8563E 3213A00104 12 mo. Jan-04 X i00033 HP 85462A 3625A00357 12 mo. Sep-03 MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 13 of 18. Measurement Data g0480109:2004-Aug-20 Fri 14:59:00 Frequency Tuned, MHz Frequency Emission, MHz Meter, dBuV CF, dB uV/m @ 3m 916.500000 916.497000 54.75 34.68 29,915.65 Supervised By: David E. Lee, Compliance Test Engineer MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 14 of 18. Name of Test: Radiated Spurious Emissions (Non-Harmonic) Specification: 47 CFR 15.249(c) Guide: ANSI/TIA/EIA-603-1992/2001, Paragraph 2.2.1 Test Equipment: As per previous page 15.249(c): Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emissions limits in § 15.209, whichever is the lesser attenuation. General Radiated Emission Limits Per 15.209: Frequency, MHz Field Strength, µV/m @ 3m 30 – 88 100 88 – 216 150 216 – 960 200 Above 960 300 Measurement Results: Frequency of Carrier, MHz = 916.500000 Spectrum Searched = 0 to 10 x FC All Other Emissions = ≥ 20 dB Below Limit Limit, µV /m @ 3m = 50 dBc or § 15.209 All Spurious Emissions were 20 Db or more below limit System sensitivity –130 dBm Supervised By: David E. Lee, Compliance Test Manager MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 15 of 18. Name of Test: Emission Masks (Occupied Bandwidth) Specification: 47 CFR 2.1049(c)(1) Guide: ANSI/TIA/EIA-603-1992, Paragraph 2.2.11 Test Equipment: As per previous page Measurement Procedure 1. The EUT and test equipment were set up as shown on the following page, with the Spectrum Analyzer connected. 2. For EUTs supporting audio modulation, the audio signal generator was adjusted to the frequency of maximum response and with output level set for ±2.5 kHz deviation (or 50% modulation). With level constant, the signal level was increased 16 dB. 3. For EUTs supporting digital modulation, the digital modulation mode was operated to its maximum extent. 4. The Occupied Bandwidth was measured with the Spectrum Analyzer controls set as shown on the test results. 5. Measurement Results: Attached MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number Transmitter Spurious Emission Test A. Occupied Bandwidth (In-Band Spurious) Test B. Out-of-Band Spurious Test (1) Sample (2) Asset Description s/n (1) Antenna – Loose Coupled (2) Spectrum Analyzer X i00029 HP 8563E 3213A00104 12 mo. Jan-04 X i00033 HP 85462A 3625A00357 12 mo. Sep-03 MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 17 of 18. Name of Test: Emission Masks (Occupied Bandwidth) g0480120: 2004-Aug-27 Fri 08.22:00 State: 2:High Power ATTEN 10dB MKR -9.7dBm RL -9.7dBm 10dB/ 916.500MHz D R START 901.00MHz STOP 929.00MHz *RBW 100kHz *VBW 300kHz SWP 50.0ms Power: HIGH (LOOSE COUPLED) Modulation: ASK BAND EDGES Supervised By: David E. Lee, Compliance Test Manager MFA p0480015, d0490022

FCCID: JLFPIC2 Page Number 18 of 18. Name of Test: Emission Masks (Occupied Bandwidth) Indicating 20 dB Bandwidth g0480119: 2004-Aug-27 Fri 08:17:00 State: 2:High Power ATTEN 10dB MKR -8.7dBm RL -8.7dBm 10dB/ 916.500MHz 3dB 20dB START 915.500MHz STOP 917.500MHz *RBW 100kHz *VBW 300kHz SWP 50.0ms Power: HIGH (LOOSE COUPLED) Modulation: ASK SIGNAL BAND WIDTH 250kHz @ 20dB Supervised By: David E. Lee, Compliance Test Manager MFA p0480015, d0490022

FCCID: JLFPIC2 NOTICE: § 15.205 Restricted Bands of Operation (a) Except as shown in paragraph (b) of this section, only spurious emissions are permitted in any of the frequency bands listed below: MHz MHz MHz GHz 0.090-0.110 16.42-16.423 399.9-410 4.5-5.25 0.495-0.505 16.69475-16.69625 608-614 5.35-5.46 2.1735-2.1905 16.80425-16.80475 960-1240 7.25-7.75 4.125-4.128 25.5-25.67 1300-1427 8.025-8.5 4.17725-4.17775 37.5-38.25 1435-1626.5 9.0-9.2 4.20725-4.20775 73-74.6 1645.5-1646.5 9.3-9.5 6.215-6.218 74.8-75.2 1660-1710 10.6-12.7 6.26775-6.26825 108-121.94 1718.8-1722.2 13.25-13.4 6.31175-6.31225 123-138 2200-2300 14.47-14.5 8.291-8.294 149.9-150.05 2310-2390 15.35-16.2 8.362-8.366 156.52475-156.52525 2483.5-2500 17.7-21.4 8.37625-8.38675 156.7-156.9 2655-2900 22.01-23.12 8.41425-8.41475 162.0125-167.17 3260-3267 23.6-24.0 12.29-12.293 167.72-173.2 3332-3339 31.2-31.8 12.51975-12.52025 240-285 3345.8-3358 36.43-36.5 12.57675-12.57725 322-339.4 3600-4400 13.36-13.41 MFA p0480015, d0490022

FCCID: JLFPIC2 Testimonial and Statement of Certification This is to certify that: 1. That the application was prepared either by, or under the direct supervision of, the undersigned. 2. That the technical data supplied with the application was taken under my direction and supervision. 3. That the data was obtained on representative units, randomly selected. 4. That, to the best of my knowledge and belief, the facts set forth in the application and accompanying technical data are true and correct. Certifying Engineer: David E. Lee, Compliance Test Manager MFA p0480015, d0490022


Document Created: 2004-09-10 17:23:20
Document Modified: 2004-09-10 17:23:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC